diff mbox series

[v3,2/2] arm64: dts: amlogic: Used onboard usb hub reset on odroid n2

Message ID 20231119023454.1591-3-linux.amoon@gmail.com (mailing list archive)
State New, archived
Headers show
Series None | expand

Commit Message

Anand Moon Nov. 19, 2023, 2:34 a.m. UTC
On Odroid n2/n2+ previously use gpio-hog to reset the usb hub,
switch to used on-board usb hub reset to enable the usb hub
and enable power to hub.

Signed-off-by: Anand Moon <linux.amoon@gmail.com>
---
v3: none
v2: none
v1: none
---
 .../dts/amlogic/meson-g12b-odroid-n2.dtsi     | 36 ++++++++++++-------
 1 file changed, 24 insertions(+), 12 deletions(-)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
index 91c9769fda20..9e671444eca6 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
@@ -31,6 +31,30 @@  hub_5v: regulator-hub_5v {
 		enable-active-high;
 	};
 
+	/* USB hub supports both USB 2.0 and USB 3.0 root hub */
+	usb-hub {
+		dr_mode = "host";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* 2.0 hub on port 1 */
+		hub_2_0: hub@1 {
+			compatible = "usb5e3,610";
+			reg = <1>;
+			peer-hub = <&hub_3_0>;
+			vdd-supply = <&usb_pwr_en>;
+		};
+
+		/* 3.0 hub on port 4 */
+		hub_3_0: hub@2 {
+			compatible = "usb5e3,620";
+			reg = <2>;
+			peer-hub = <&hub_2_0>;
+			reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>;
+			vdd-supply = <&vcc_5v>;
+		};
+	};
+
 	sound {
 		compatible = "amlogic,axg-sound-card";
 		model = "ODROID-N2";
@@ -234,18 +258,6 @@  &gpio {
 		"PIN_3",  /* GPIOX_17 */
 		"PIN_5",  /* GPIOX_18 */
 		"PIN_36"; /* GPIOX_19 */
-	/*
-	 * WARNING: The USB Hub on the Odroid-N2 needs a reset signal
-	 * to be turned high in order to be detected by the USB Controller
-	 * This signal should be handled by a USB specific power sequence
-	 * in order to reset the Hub when USB bus is powered down.
-	 */
-	usb-hub-hog {
-		gpio-hog;
-		gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "usb-hub-reset";
-	};
 };
 
 &i2c3 {