diff mbox series

[v5,2/2] arm64: dts: amlogic: add support for xiaomi-aquaman/Mi TV Stick

Message ID 20250319190150.31529-4-funderscore@postmarketos.org (mailing list archive)
State New
Headers show
Series Add support for Xiaomi Mi TV Stick | expand

Commit Message

Ferass El Hafidi March 19, 2025, 7:01 p.m. UTC 
Xiaomi Mi TV Stick is a small Amlogic-based Android TV stick released in
2020.  It is known as `xiaomi-aquaman` internally.  Specifications:
 * Amlogic S805Y SoC
 * Android TV 9, upgradable to Android TV 10
 * 8 GB eMMC
 * 1 GB of RAM
 * Wi-Fi + Bluetooth

The devicetree is based on p241's DT, with some changes to better match
the Mi TV Stick:
 * there is no Ethernet port, no IR, no CVBS connector on the stick
 * a white LED is present
 * adjust memory to have 1 GB of RAM available

Signed-off-by: Ferass El Hafidi <funderscore@postmarketos.org>
---
 arch/arm64/boot/dts/amlogic/Makefile          |   1 +
 .../meson-gxl-s805y-xiaomi-aquaman.dts        | 292 ++++++++++++++++++
 .../boot/dts/amlogic/meson-gxl-s805y.dtsi     |  10 +
 3 files changed, 303 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s805y-xiaomi-aquaman.dts
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s805y.dtsi

Comments

Martin Blumenstingl March 19, 2025, 10:36 p.m. UTC | #1 
Hello,

thanks for your contribution and sorry for the late reply!

On Wed, Mar 19, 2025 at 8:02 PM Ferass El Hafidi
<funderscore@postmarketos.org> wrote:
[...]
> +       au2: analog-amplifier {
> +               compatible = "simple-audio-amplifier";
> +               sound-name-prefix = "AU2";
> +               VCC-supply = <&vcc_5v>;
> +               enable-gpios = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>;
> +       };
I couldn't find any pictures online that show an analog audio output
(typically a 3.5mm socket).
Can you confirm that this is really present?

[...]
> +       sound {
> +               compatible = "amlogic,gx-sound-card";
> +               model = "XIAOMI-AQUAMAN";
> +               audio-aux-devs = <&au2>;
> +               audio-widgets = "Line", "Lineout";
> +               audio-routing = "AU2 INL", "ACODEC LOLN",
> +                               "AU2 INR", "ACODEC LORN",
> +                               "Lineout", "AU2 OUTL",
> +                               "Lineout", "AU2 OUTR";
If there's no analog audio in/out then this section can be cleaned up
as well - together with the references to acodec in the dai-links
below.

[...]
> +/* Wireless SDIO Module (Amlogic W155S1 / Realtek RTL8821CS) */
> +&sd_emmc_b {
question to Neil: since we know that there's two board variants out
there (with different wifi chipsets) - are dt overlays down the road
enough (to enable Bluetooth / wifi - depending on the chipset or board
revision) or do we need to split the whole .dts?


Best regards,
Martin
Ferass El Hafidi March 20, 2025, 11:03 a.m. UTC | #2 
On Wed Mar 19, 2025 at 10:36 PM UTC, Martin Blumenstingl wrote:
> Hello,
>
> thanks for your contribution and sorry for the late reply!
>
> On Wed, Mar 19, 2025 at 8:02 PM Ferass El Hafidi
> <funderscore@postmarketos.org> wrote:
> [...]
> > +       au2: analog-amplifier {
> > +               compatible = "simple-audio-amplifier";
> > +               sound-name-prefix = "AU2";
> > +               VCC-supply = <&vcc_5v>;
> > +               enable-gpios = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>;
> > +       };
> I couldn't find any pictures online that show an analog audio output
> (typically a 3.5mm socket).
> Can you confirm that this is really present?
>
> [...]
> > +       sound {
> > +               compatible = "amlogic,gx-sound-card";
> > +               model = "XIAOMI-AQUAMAN";
> > +               audio-aux-devs = <&au2>;
> > +               audio-widgets = "Line", "Lineout";
> > +               audio-routing = "AU2 INL", "ACODEC LOLN",
> > +                               "AU2 INR", "ACODEC LORN",
> > +                               "Lineout", "AU2 OUTL",
> > +                               "Lineout", "AU2 OUTR";
> If there's no analog audio in/out then this section can be cleaned up
> as well - together with the references to acodec in the dai-links
> below.

Oops, completely overlooked those.  Will fix in v6.  There indeed is no 
analog audio output.

>
> [...]
> > +/* Wireless SDIO Module (Amlogic W155S1 / Realtek RTL8821CS) */
> > +&sd_emmc_b {
> question to Neil: since we know that there's two board variants out
> there (with different wifi chipsets) - are dt overlays down the road
> enough (to enable Bluetooth / wifi - depending on the chipset or board
> revision) or do we need to split the whole .dts?
>

So far W155S1 and RTL8821CS are the *known* chipsets used, but there may 
be others.  Right now it's not my main concern, as W155S1 is not
supported in Mainline, as far as I know, and I can't test RTL8821CS
because my variant seems to have the former.

>
> Best regards,
> Martin

Regards.
Neil Armstrong March 24, 2025, 7:02 a.m. UTC | #3 
On 19/03/2025 20:01, Ferass El Hafidi wrote:
> Xiaomi Mi TV Stick is a small Amlogic-based Android TV stick released in
> 2020.  It is known as `xiaomi-aquaman` internally.  Specifications:
>   * Amlogic S805Y SoC
>   * Android TV 9, upgradable to Android TV 10
>   * 8 GB eMMC
>   * 1 GB of RAM
>   * Wi-Fi + Bluetooth
> 
> The devicetree is based on p241's DT, with some changes to better match
> the Mi TV Stick:
>   * there is no Ethernet port, no IR, no CVBS connector on the stick
>   * a white LED is present
>   * adjust memory to have 1 GB of RAM available
> 
> Signed-off-by: Ferass El Hafidi <funderscore@postmarketos.org>
> ---
>   arch/arm64/boot/dts/amlogic/Makefile          |   1 +
>   .../meson-gxl-s805y-xiaomi-aquaman.dts        | 292 ++++++++++++++++++
>   .../boot/dts/amlogic/meson-gxl-s805y.dtsi     |  10 +
>   3 files changed, 303 insertions(+)
>   create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s805y-xiaomi-aquaman.dts
>   create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s805y.dtsi
> 
> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
> index 2fbda8419..0921707f1 100644
> --- a/arch/arm64/boot/dts/amlogic/Makefile
> +++ b/arch/arm64/boot/dts/amlogic/Makefile
> @@ -49,6 +49,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-wetek-hub.dtb
>   dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-wetek-play2.dtb
>   dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-libretech-ac.dtb
>   dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb
> +dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805y-xiaomi-aquaman.dtb
>   dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-libretech-pc.dtb
>   dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-mecool-kii-pro.dtb
>   dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p230.dtb
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s805y-xiaomi-aquaman.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s805y-xiaomi-aquaman.dts
> new file mode 100644
> index 000000000..42c692017
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s805y-xiaomi-aquaman.dts
> @@ -0,0 +1,292 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2025 Ferass El Hafidi <funderscore@postmarketos.org>
> + * Heavily based on meson-gxl-s805x-p241.dtb:
> + *  - Copyright (c) 2018 BayLibre, SAS.
> + *    Author: Neil Armstrong <narmstrong@baylibre.com>
> + *    Author: Jerome Brunet <jbrunet@baylibre.com>
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/sound/meson-aiu.h>
> +
> +#include "meson-gxl-s805y.dtsi"
> +
> +/ {
> +	compatible = "xiaomi,aquaman", "amlogic,s805y", "amlogic,meson-gxl";
> +	model = "Xiaomi Mi TV Stick (aquaman)";
> +
> +	aliases {
> +		serial0 = &uart_AO;
> +		serial1 = &uart_A;
> +	};
> +
> +	au2: analog-amplifier {
> +		compatible = "simple-audio-amplifier";
> +		sound-name-prefix = "AU2";
> +		VCC-supply = <&vcc_5v>;
> +		enable-gpios = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	emmc_pwrseq: emmc-pwrseq {
> +		compatible = "mmc-pwrseq-emmc";
> +		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
> +	};
> +
> +	hdmi-connector {
> +		compatible = "hdmi-connector";
> +		type = "a";
> +
> +		port {
> +			hdmi_connector_in: endpoint {
> +				remote-endpoint = <&hdmi_tx_tmds_out>;
> +			};
> +		};
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		led-white {
> +			color = <LED_COLOR_ID_WHITE>;
> +			function = LED_FUNCTION_POWER;
> +			gpios = <&gpio GPIODV_24 GPIO_ACTIVE_HIGH>;
> +			default-state = "on";
> +			panic-indicator;
> +		};
> +	};
> +
> +	memory@0 {
> +		device_type = "memory";
> +		reg = <0x0 0x0 0x0 0x40000000>;
> +	};
> +
> +	vddio_boot: regulator-vddio-boot {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDIO_BOOT";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +	};
> +
> +	vddao_3v3: regulator-vddao-3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDAO_3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +
> +	vddio_ao18: regulator-vddio-ao18 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDIO_AO18";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +	};
> +
> +	vcc_3v3: regulator-vcc-3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VCC_3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +
> +	vcc_5v: regulator-vcc-5v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VCC_5V";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +	};
> +
> +	emmc_pwrseq: emmc-pwrseq {
> +		compatible = "mmc-pwrseq-emmc";
> +		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
> +	};
> +
> +	wifi32k: wifi32k {
> +		compatible = "pwm-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <32768>;
> +		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
> +	};
> +
> +	sdio_pwrseq: sdio-pwrseq {
> +		compatible = "mmc-pwrseq-simple";
> +		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
> +		clocks = <&wifi32k>;
> +		clock-names = "ext_clock";
> +	};
> +
> +	sound {
> +		compatible = "amlogic,gx-sound-card";
> +		model = "XIAOMI-AQUAMAN";
> +		audio-aux-devs = <&au2>;
> +		audio-widgets = "Line", "Lineout";
> +		audio-routing = "AU2 INL", "ACODEC LOLN",
> +				"AU2 INR", "ACODEC LORN",
> +				"Lineout", "AU2 OUTL",
> +				"Lineout", "AU2 OUTR";
> +		clocks = <&clkc CLKID_MPLL0>,
> +			 <&clkc CLKID_MPLL1>,
> +			 <&clkc CLKID_MPLL2>;
> +
> +		assigned-clocks = <&clkc CLKID_MPLL0>,
> +				  <&clkc CLKID_MPLL1>,
> +				  <&clkc CLKID_MPLL2>;
> +		assigned-clock-parents = <0>, <0>, <0>;
> +		assigned-clock-rates = <294912000>,
> +				       <270950400>,
> +				       <393216000>;
> +
> +		dai-link-0 {
> +			sound-dai = <&aiu AIU_CPU CPU_I2S_FIFO>;
> +		};
> +
> +		dai-link-1 {
> +			sound-dai = <&aiu AIU_CPU CPU_I2S_ENCODER>;
> +			dai-format = "i2s";
> +			mclk-fs = <256>;
> +
> +			codec-0 {
> +				sound-dai = <&aiu AIU_HDMI CTRL_I2S>;
> +			};
> +
> +			codec-1 {
> +				sound-dai = <&aiu AIU_ACODEC CTRL_I2S>;
> +			};
> +		};
> +
> +		dai-link-2 {
> +			sound-dai = <&aiu AIU_HDMI CTRL_OUT>;
> +
> +			codec-0 {
> +				sound-dai = <&hdmi_tx>;
> +			};
> +		};
> +
> +		dai-link-3 {
> +			sound-dai = <&aiu AIU_ACODEC CTRL_OUT>;
> +
> +			codec-0 {
> +				sound-dai = <&acodec>;
> +			};
> +		};
> +	};
> +};
> +
> +&acodec {
> +	AVDD-supply = <&vddio_ao18>;
> +	status = "okay";
> +};
> +
> +&aiu {
> +	status = "okay";
> +};
> +
> +&cec_AO {
> +	status = "okay";
> +	pinctrl-0 = <&ao_cec_pins>;
> +	pinctrl-names = "default";
> +	hdmi-phandle = <&hdmi_tx>;
> +};
> +
> +&hdmi_tx {
> +	status = "okay";
> +	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
> +	pinctrl-names = "default";
> +	hdmi-supply = <&vcc_5v>;
> +};
> +
> +&hdmi_tx_tmds_port {
> +	hdmi_tx_tmds_out: endpoint {
> +		remote-endpoint = <&hdmi_connector_in>;
> +	};
> +};
> +
> +&saradc {
> +	status = "okay";
> +	vref-supply = <&vddio_ao18>;
> +};
> +
> +/* Wireless SDIO Module (Amlogic W155S1 / Realtek RTL8821CS) */
> +&sd_emmc_b {
> +	status = "okay";
> +	pinctrl-0 = <&sdio_pins>;
> +	pinctrl-1 = <&sdio_clk_gate_pins>;
> +	pinctrl-names = "default", "clk-gate";
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +
> +	bus-width = <4>;
> +	cap-sd-highspeed;
> +	max-frequency = <50000000>;
> +
> +	non-removable;
> +	disable-wp;
> +
> +	/* WiFi firmware requires power to be kept while in suspend */
> +	keep-power-in-suspend;
> +
> +	mmc-pwrseq = <&sdio_pwrseq>;
> +
> +	vmmc-supply = <&vddao_3v3>;
> +	vqmmc-supply = <&vddio_boot>;
> +
> +	sdio: wifi@1 {
> +		reg = <1>;
> +	}
> +};
> +
> +/* eMMC */
> +&sd_emmc_c {
> +	status = "okay";
> +	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
> +	pinctrl-1 = <&emmc_clk_gate_pins>;
> +	pinctrl-names = "default", "clk-gate";
> +
> +	bus-width = <8>;
> +	cap-mmc-highspeed;
> +	max-frequency = <200000000>;
> +	non-removable;
> +	disable-wp;
> +	mmc-ddr-1_8v;
> +	mmc-hs200-1_8v;
> +
> +	mmc-pwrseq = <&emmc_pwrseq>;
> +	vmmc-supply = <&vcc_3v3>;
> +	vqmmc-supply = <&vddio_boot>;
> +};
> +
> +&pwm_ef {
> +	status = "okay";
> +	pinctrl-0 = <&pwm_e_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +/*
> + * This is connected to the Bluetooth module
> + * Note: There's no driver for the Bluetooth module of some variants yet.
> + */
> +&uart_A {
> +	status = "okay";
> +	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
> +	pinctrl-names = "default";
> +	uart-has-rtscts;
> +};
> +
> +&uart_AO {
> +	status = "okay";
> +	pinctrl-0 = <&uart_ao_a_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +&usb {
> +	status = "okay";
> +	dr_mode = "otg";
> +	vbus-supply = <&vcc_5v>;
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s805y.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl-s805y.dtsi
> new file mode 100644
> index 000000000..49b29b71f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s805y.dtsi
> @@ -0,0 +1,10 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2025 Ferass El Hafidi <funderscore@postmarketos.org>
> + */
> +
> +#include "meson-gxl-s805x.dtsi"
> +
> +/ {
> +	compatible = "amlogic,s805y", "amlogic,meson-gxl";
> +};

I get:
Error: arch/arm64/boot/dts/amlogic/meson-gxl-s805y-xiaomi-aquaman.dts:243.1-2 syntax error
FATAL ERROR: Unable to parse input tree

whil building, could you fix that ?

Neil
Neil Armstrong March 24, 2025, 7:03 a.m. UTC | #4 
On 19/03/2025 23:36, Martin Blumenstingl wrote:
> Hello,
> 
> thanks for your contribution and sorry for the late reply!
> 
> On Wed, Mar 19, 2025 at 8:02 PM Ferass El Hafidi
> <funderscore@postmarketos.org> wrote:
> [...]
>> +       au2: analog-amplifier {
>> +               compatible = "simple-audio-amplifier";
>> +               sound-name-prefix = "AU2";
>> +               VCC-supply = <&vcc_5v>;
>> +               enable-gpios = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>;
>> +       };
> I couldn't find any pictures online that show an analog audio output
> (typically a 3.5mm socket).
> Can you confirm that this is really present?
> 
> [...]
>> +       sound {
>> +               compatible = "amlogic,gx-sound-card";
>> +               model = "XIAOMI-AQUAMAN";
>> +               audio-aux-devs = <&au2>;
>> +               audio-widgets = "Line", "Lineout";
>> +               audio-routing = "AU2 INL", "ACODEC LOLN",
>> +                               "AU2 INR", "ACODEC LORN",
>> +                               "Lineout", "AU2 OUTL",
>> +                               "Lineout", "AU2 OUTR";
> If there's no analog audio in/out then this section can be cleaned up
> as well - together with the references to acodec in the dai-links
> below.
> 
> [...]
>> +/* Wireless SDIO Module (Amlogic W155S1 / Realtek RTL8821CS) */
>> +&sd_emmc_b {
> question to Neil: since we know that there's two board variants out
> there (with different wifi chipsets) - are dt overlays down the road
> enough (to enable Bluetooth / wifi - depending on the chipset or board
> revision) or do we need to split the whole .dts?

Perhaps yes

Neil

> 
> 
> Best regards,
> Martin
Ferass El Hafidi March 24, 2025, 11 a.m. UTC | #5 
On Mon Mar 24, 2025 at 7:02 AM UTC, Neil Armstrong wrote:
> I get:
> Error: arch/arm64/boot/dts/amlogic/meson-gxl-s805y-xiaomi-aquaman.dts:243.1-2 syntax error
> FATAL ERROR: Unable to parse input tree

Yes, somehow a ";" is missing.

>
> whil building, could you fix that ?
>
> Neil
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 2fbda8419..0921707f1 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -49,6 +49,7 @@  dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-wetek-hub.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-wetek-play2.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-libretech-ac.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805y-xiaomi-aquaman.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-libretech-pc.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-mecool-kii-pro.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p230.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s805y-xiaomi-aquaman.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s805y-xiaomi-aquaman.dts
new file mode 100644
index 000000000..42c692017
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s805y-xiaomi-aquaman.dts
@@ -0,0 +1,292 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2025 Ferass El Hafidi <funderscore@postmarketos.org>
+ * Heavily based on meson-gxl-s805x-p241.dtb:
+ *  - Copyright (c) 2018 BayLibre, SAS.
+ *    Author: Neil Armstrong <narmstrong@baylibre.com>
+ *    Author: Jerome Brunet <jbrunet@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/sound/meson-aiu.h>
+
+#include "meson-gxl-s805y.dtsi"
+
+/ {
+	compatible = "xiaomi,aquaman", "amlogic,s805y", "amlogic,meson-gxl";
+	model = "Xiaomi Mi TV Stick (aquaman)";
+
+	aliases {
+		serial0 = &uart_AO;
+		serial1 = &uart_A;
+	};
+
+	au2: analog-amplifier {
+		compatible = "simple-audio-amplifier";
+		sound-name-prefix = "AU2";
+		VCC-supply = <&vcc_5v>;
+		enable-gpios = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-white {
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&gpio GPIODV_24 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+			panic-indicator;
+		};
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	vddio_boot: regulator-vddio-boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddao_3v3: regulator-vddao-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vddio_ao18: regulator-vddio-ao18 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vcc_3v3: regulator-vcc-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcc_5v: regulator-vcc-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+
+	sound {
+		compatible = "amlogic,gx-sound-card";
+		model = "XIAOMI-AQUAMAN";
+		audio-aux-devs = <&au2>;
+		audio-widgets = "Line", "Lineout";
+		audio-routing = "AU2 INL", "ACODEC LOLN",
+				"AU2 INR", "ACODEC LORN",
+				"Lineout", "AU2 OUTL",
+				"Lineout", "AU2 OUTR";
+		clocks = <&clkc CLKID_MPLL0>,
+			 <&clkc CLKID_MPLL1>,
+			 <&clkc CLKID_MPLL2>;
+
+		assigned-clocks = <&clkc CLKID_MPLL0>,
+				  <&clkc CLKID_MPLL1>,
+				  <&clkc CLKID_MPLL2>;
+		assigned-clock-parents = <0>, <0>, <0>;
+		assigned-clock-rates = <294912000>,
+				       <270950400>,
+				       <393216000>;
+
+		dai-link-0 {
+			sound-dai = <&aiu AIU_CPU CPU_I2S_FIFO>;
+		};
+
+		dai-link-1 {
+			sound-dai = <&aiu AIU_CPU CPU_I2S_ENCODER>;
+			dai-format = "i2s";
+			mclk-fs = <256>;
+
+			codec-0 {
+				sound-dai = <&aiu AIU_HDMI CTRL_I2S>;
+			};
+
+			codec-1 {
+				sound-dai = <&aiu AIU_ACODEC CTRL_I2S>;
+			};
+		};
+
+		dai-link-2 {
+			sound-dai = <&aiu AIU_HDMI CTRL_OUT>;
+
+			codec-0 {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+
+		dai-link-3 {
+			sound-dai = <&aiu AIU_ACODEC CTRL_OUT>;
+
+			codec-0 {
+				sound-dai = <&acodec>;
+			};
+		};
+	};
+};
+
+&acodec {
+	AVDD-supply = <&vddio_ao18>;
+	status = "okay";
+};
+
+&aiu {
+	status = "okay";
+};
+
+&cec_AO {
+	status = "okay";
+	pinctrl-0 = <&ao_cec_pins>;
+	pinctrl-names = "default";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
+	pinctrl-names = "default";
+	hdmi-supply = <&vcc_5v>;
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddio_ao18>;
+};
+
+/* Wireless SDIO Module (Amlogic W155S1 / Realtek RTL8821CS) */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+
+	non-removable;
+	disable-wp;
+
+	/* WiFi firmware requires power to be kept while in suspend */
+	keep-power-in-suspend;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+
+	sdio: wifi@1 {
+		reg = <1>;
+	}
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins>;
+	pinctrl-names = "default";
+};
+
+/*
+ * This is connected to the Bluetooth module
+ * Note: There's no driver for the Bluetooth module of some variants yet.
+ */
+&uart_A {
+	status = "okay";
+	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+};
+
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb {
+	status = "okay";
+	dr_mode = "otg";
+	vbus-supply = <&vcc_5v>;
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s805y.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl-s805y.dtsi
new file mode 100644
index 000000000..49b29b71f
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s805y.dtsi
@@ -0,0 +1,10 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2025 Ferass El Hafidi <funderscore@postmarketos.org>
+ */
+
+#include "meson-gxl-s805x.dtsi"
+
+/ {
+	compatible = "amlogic,s805y", "amlogic,meson-gxl";
+};