[v2,00/10] Enable per-port SATA interrupts and drop an hack in the IRQ subsystem

Message

Miquel Raynal March 6, 2019, 10:21 a.m. UTC

Hello,

Some time ago, when the initial support for Armada CP110 was
contributed, the SATA core was not able to handle per-port
interrupts. Despite the hardware reality, the device tree only
represents one main interrupt for the two ports. Having both SATA
ports enabled at the same time has been achieved by a hack in the ICU
driver(1) that faked the use of the two interrupts, no matter which
SATA port was in use.

Now that the SATA core is ready to handle more than one interrupt,
this series adds support for it in the libahci_platform code. The
CP110 device tree must be updated to reflect the two SATA ports
available and their respective interrupts. To do not break DT backward
compatibility, the ahci_platform driver now embeds a special quirk
which checks if the DT is valid (only for A8k compatible) and, if
needed, creates the two missing sub-nodes, and assign them the
relevant "reg" and "interrupts" properties, before removing the main
SATA node "interrupts" one.


Thanks,
Miquèl

(1) The ICU is an irqchip aggregating the CP110 (south-bridge)
interrupts into MSIs for the AP806 (north-bridge).

Changes in v2
=============
* In the AHCI world, the 'irq' is now an '*irqs' array, I ensured it
  is allocated even when not using *_platform drivers.
* Moved the whole logic from the generic ahci_platform.c driver to the
  Marvell's ahci_mvebu.c driver.
* Dropped the whole DT manipulation quirk.
* Instead used a hack to configure both interrupts when using the
  deprecated bindings, this hack is a8k specific but there is a flag
  that is passed to the core during the ahci_platform_get_resources()
  to indicate that the number of ports must be forced to 2 no matter
  the number of child nodes.
* The A8k based Clearfog-GT actually uses the SATA IP (Baruch's info)
  so do not remove the SATA node from the DT. Instead, change the DTS
  to fit the new bindings (the board only uses the second port at
  offset 1).
* Added bindings documentation about the A8k AHCI compatible (existing
  in DTs, missing in the doc).
* SATA Sub-nodes representing ports already are documented, I just
  added a mention that they can also have an interrupts property which
  is mutually exclusive with the root SATA node.


Miquel Raynal (9):
  ata: libahci: Ensure the host interrupt status bits are cleared
  ata: ahci: Support per-port interrupts
  dt-bindings: ata: Update ahci bindings with possible per-port
    interrupts
  ata: ahci: mvebu: Rename a platform data flag
  ata: ahci: mvebu: Add a parameter to a platform data callback
  dt-bindings: ata: Update ahci_mvebu bindings
  ata: ahci: mvebu: Support A8k compatible
  ata: ahci: mvebu: Add support for A8k legacy bindings
  irqchip/irq-mvebu-icu: Remove the double SATA ports interrupt hack

Thomas Petazzoni (1):
  arm64: dts: marvell: armada-cp110: Switch to per-port SATA interrupts

 .../devicetree/bindings/ata/ahci-platform.txt |  7 ++
 .../arm64/boot/dts/marvell/armada-7040-db.dts |  7 +-
 .../marvell/armada-8040-clearfog-gt-8k.dts    |  5 +-
 .../arm64/boot/dts/marvell/armada-8040-db.dts | 14 +++-
 arch/arm64/boot/dts/marvell/armada-cp110.dtsi | 16 ++++-
 drivers/ata/acard-ahci.c                      |  2 +-
 drivers/ata/ahci.c                            |  8 ++-
 drivers/ata/ahci.h                            |  3 +-
 drivers/ata/ahci_mvebu.c                      | 61 +++++++++++++---
 drivers/ata/libahci.c                         |  9 ++-
 drivers/ata/libahci_platform.c                | 70 ++++++++++++++++---
 drivers/ata/sata_highbank.c                   |  2 +-
 drivers/irqchip/irq-mvebu-icu.c               | 18 -----
 include/linux/ahci_platform.h                 |  1 +
 14 files changed, 174 insertions(+), 49 deletions(-)