| Message ID | 20190813113627.27251-1-vidyas@nvidia.com (mailing list archive) |
|---|---|
| Headers | show |
| Series | PCI: tegra: Add Tegra194 PCIe support | expand |
On Tue, Aug 13, 2019 at 05:06:14PM +0530, Vidya Sagar wrote: > Tegra194 has six PCIe controllers based on Synopsys DesignWare core. > There are two Universal PHY (UPHY) blocks with each supporting 12(HSIO: > Hisg Speed IO) and 8(NVHS: NVIDIA High Speed) lanes respectively. > Controllers:0~4 use UPHY lanes from HSIO brick whereas Controller:5 uses > UPHY lanes from NVHS brick. Lane mapping in HSIO UPHY brick to each PCIe > controller (0~4) is controlled in XBAR module by BPMP-FW. Since PCIe > core has PIPE interface, a glue module called PIPE-to-UPHY (P2U) is used > to connect each UPHY lane (applicable to both HSIO and NVHS UPHY bricks) > to PCIe controller > This patch series > - Adds support for P2U PHY driver > - Adds support for PCIe host controller > - Adds device tree nodes each PCIe controllers > - Enables nodes applicable to p2972-0000 platform > - Adds helper APIs in Designware core driver to get capability regs offset > - Adds defines for new feature registers of PCIe spec revision 4 > - Makes changes in DesignWare core driver to get Tegra194 PCIe working > > Testing done on P2972-0000 platform > - Able to get PCIe link up with on-board Marvel eSATA controller > - Able to get PCIe link up with NVMe cards connected to M.2 Key-M slot > - Able to do data transfers with both SATA drives and NVMe cards > - Able to perform suspend-resume sequence > > Note > - Enabling x8 slot on P2972-0000 platform requires pinmux driver for Tegra194. > It is being worked on currently and hence Controller:5 (i.e. x8 slot) is > disabled in this patch series. A future patch series would enable this. > - This series is based on top of the following series > Jisheng's patches to add support to .remove() in Designware sub-system > https://patchwork.kernel.org/project/linux-pci/list/?series=98559 > (Update: Jisheng's patches are now accepted and applied for v5.2) > My patches made on top of Jisheng's patches to export various symbols > http://patchwork.ozlabs.org/project/linux-pci/list/?series=115671 > (Update: My above patch series is accepted and applied for v5.3) > Another patch of mine to enable BPMP-FW resume in noirq phase > http://patchwork.ozlabs.org/patch/1140973/ > (This is already accepted) > > V16: > * Added empty lines (cosmetic changes) where required in pcie-tegra194.c file > to address Lorenzo's review comments. > > V15: > * Refactored pcie-tegra194.c code to call only tegra_bpmp_transfer() API > in both .probe() path and .resume_noirq() path. > > V14: > * Addressed Lorenzo's review comments in pcie-tegra194.c file (Patch 13/13) > * Added a new patch to export dw_pcie_wait_for_link() API > > V13: > * Addressed Bjorn's review comments for adding Gen-4 specific defines to pci_regs.h header file > > V12: > * Modified the commit message of patch-3 in this series to address review > comments from Lorenzo > > V11: > * Removed device-tree patches from the series as they are applied to relevant > Tegra specific trees by Thierry Reding. > * Included older Tegra chips to extend quirk that disables MSI interrupt being > used for Tegra PCIe root ports. > * Addressed review comments in P2U driver file. > > V10: > * Used _relaxed() versions of readl() & writel() > > V9: > * Made the drivers dependent on ARCH_TEGRA_194_SOC directly > * Addressed review comments from Dmitry > > V8: > * Changed P2U driver file name from pcie-p2u-tegra194.c to phy-tegra194-p2u.c > * Addressed review comments from Thierry and Rob > > V7: > * Took care of review comments from Rob > * Added a quirk to disable MSI for root ports > * Removed using pcie_pme_disable_msi() API in host controller driver > > V6: > * Removed patch that exports pcie_bus_config symbol > * Took care of review comments from Thierry and Rob > > V5: > * Removed redundant APIs in pcie-designware-ep.c file after moving them > to pcie-designware.c file based on Bjorn's review comments > > V4: > * Rebased on top of linux-next top of the tree > * Addressed Gustavo's comments and added his Ack for some of the changes. > > V3: > * Addressed review comments from Thierry > > V2: > * Addressed review comments from Bjorn, Thierry, Jonathan, Rob & Kishon > * Added more patches in v2 series > > Vidya Sagar (13): > PCI: Add #defines for some of PCIe spec r4.0 features > PCI: Disable MSI for Tegra root ports > PCI: dwc: Perform dbi regs write lock towards the end > PCI: dwc: Move config space capability search API > PCI: dwc: Add ext config space capability search API > PCI: dwc: Export dw_pcie_wait_for_link() API > dt-bindings: PCI: designware: Add binding for CDM register check > PCI: dwc: Add support to enable CDM register check > dt-bindings: Add PCIe supports-clkreq property > dt-bindings: PCI: tegra: Add device tree support for Tegra194 > dt-bindings: PHY: P2U: Add Tegra194 P2U block > phy: tegra: Add PCIe PIPE2UPHY support > PCI: tegra: Add Tegra194 PCIe support > > .../bindings/pci/designware-pcie.txt | 5 + > .../bindings/pci/nvidia,tegra194-pcie.txt | 155 ++ > Documentation/devicetree/bindings/pci/pci.txt | 5 + > .../bindings/phy/phy-tegra194-p2u.txt | 28 + > drivers/pci/controller/dwc/Kconfig | 10 + > drivers/pci/controller/dwc/Makefile | 1 + > .../pci/controller/dwc/pcie-designware-ep.c | 37 +- > .../pci/controller/dwc/pcie-designware-host.c | 14 +- > drivers/pci/controller/dwc/pcie-designware.c | 88 + > drivers/pci/controller/dwc/pcie-designware.h | 12 + > drivers/pci/controller/dwc/pcie-tegra194.c | 1631 +++++++++++++++++ > drivers/pci/quirks.c | 53 + > drivers/phy/tegra/Kconfig | 7 + > drivers/phy/tegra/Makefile | 1 + > drivers/phy/tegra/phy-tegra194-p2u.c | 120 ++ > include/uapi/linux/pci_regs.h | 14 +- > 16 files changed, 2139 insertions(+), 42 deletions(-) > create mode 100644 Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt > create mode 100644 Documentation/devicetree/bindings/phy/phy-tegra194-p2u.txt > create mode 100644 drivers/pci/controller/dwc/pcie-tegra194.c > create mode 100644 drivers/phy/tegra/phy-tegra194-p2u.c > I have applied it to pci/tegra, subject to kbuild test validation, for v5.4. Thanks, Lorenzo