mbox series

[net-next,v4,00/11] net: ethernet: ti: add networking support for k3 am65x/j721e soc

Message ID 20200317072739.23950-1-grygorii.strashko@ti.com (mailing list archive)
Headers show
Series net: ethernet: ti: add networking support for k3 am65x/j721e soc | expand

Message

Grygorii Strashko March 17, 2020, 7:27 a.m. UTC 
Hi

This v4 series adds basic networking support support TI K3 AM654x/J721E SoC which
have integrated Gigabit Ethernet MAC (Media Access Controller) into device MCU
domain and named MCU_CPSW0 (CPSW2G NUSS).

Formally TRMs refer CPSW2G NUSS as two-port Gigabit Ethernet Switch subsystem
with port 0 being the CPPI DMA host port and port 1 being the external Ethernet
port, but for 1 external port device it's just Port 0 <-> ALE <-> Port 1 and it's
rather device with HW filtering capabilities then actually switching device.
It's expected to have similar devices, but with more external ports.

The new Host port 0 Communications Port Programming Interface (CPPI5) is
operating by TI AM654x/J721E NAVSS Unified DMA Peripheral Root Complex (UDMA-P)
controller [1].

The CPSW2G contains below modules for which existing code is re-used:
 - MAC SL: cpsw_sl.c
 - Address Lookup Engine (ALE): cpsw_ale.c, basically compatible with K2 66AK2E/G
 - Management Data Input/Output interface (MDIO): davinci_mdio.c, fully 
   compatible with TI AM3/4/5 devices

Basic features supported by CPSW2G NUSS driver:
 - VLAN support, 802.1Q compliant, Auto add port VLAN for untagged frames on
   ingress, Auto VLAN removal on egress and auto pad to minimum frame size.
 - multicast filtering
 - promisc mode
 - TX multiq support in Round Robin or Fixed priority modes
 - RX checksum offload for non-fragmented IPv4/IPv6 TCP/UDP packets
 - TX checksum offload support for IPv4/IPv6 TCP/UDP packets (J721E only).

Features under development:
 - Support for IEEE 1588 Clock Synchronization. The CPSW2G NUSS includes new
   version of Common Platform Time Sync (CPTS)
 - tc-mqprio: priority level Quality Of Service (QOS) support (802.1p)
 - tc-cbs: Support for Audio/Video Bridging (P802.1Qav/D6.0) HW shapers
 - tc-taprio: IEEE 802.1Qbv/D2.2 Enhancements for Scheduled Traffic
 - frame preemption: IEEE P902.3br/D2.0 Interspersing Express Traffic, 802.1Qbu
 - extended ALE features: classifier/policers, auto-aging

Patches 1-6 are intended for netdev, Patches 7-11 are intended for K3 Platform
tree and provided here for testing purposes.

Changes in v4:
 - fixed minor comments from Jakub Kicinski <kuba@kernel.org>
 - dependencies resolved: required phy-rmii-sel changes [2] queued for merge
   except one [3] which is included in this series with Kishon's ask.

Changes in v3:
 - add ARM64 defconfig changes for testing purposes
 - fixed DT yaml definition
 - fixed comments from Jakub Kicinski <kuba@kernel.org>

Changes in v2:
 - fixed DT yaml definition
 - fixed comments from David Miller

v3: https://patchwork.ozlabs.org/cover/1254568/
v2: https://patchwork.ozlabs.org/cover/1250674/
v1: https://lwn.net/Articles/813087/

TRMs:
 AM654: http://www.ti.com/lit/ug/spruid7e/spruid7e.pdf
 J721E: http://www.ti.com/lit/ug/spruil1a/spruil1a.pdf

Preliminary documentation can be found at:
 http://software-dl.ti.com/processor-sdk-linux/esd/docs/latest/linux/Foundational_Components/Kernel/Kernel_Drivers/Network/K3_CPSW2g.html

[1] https://lwn.net/Articles/808030/
[2] https://lkml.org/lkml/2020/2/22/100
[3] https://lkml.org/lkml/2020/3/3/724

Grygorii Strashko (11):
  phy: ti: gmii-sel: simplify config dependencies between net drivers
    and gmii phy
  net: ethernet: ti: ale: fix seeing unreg mcast packets with promisc
    and allmulti disabled
  net: ethernet: ti: ale: add support for mac-only mode
  net: ethernet: ti: ale: am65: add support for default thread cfg
  dt-binding: ti: am65x: document mcu cpsw nuss
  net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver
  arm64: dts: ti: k3-am65-mcu: add cpsw nuss node
  arm64: dts: k3-am654-base-board: add mcu cpsw nuss pinmux and phy defs
  arm64: dts: ti: k3-j721e-mcu: add mcu cpsw nuss node
  arm64: dts: ti: k3-j721e-common-proc-board: add mcu cpsw nuss pinmux
    and phy defs
  arm64: defconfig: ti: k3: enable dma and networking

 .../bindings/net/ti,k3-am654-cpsw-nuss.yaml   |  226 ++
 arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi       |   49 +
 arch/arm64/boot/dts/ti/k3-am65.dtsi           |    1 +
 .../arm64/boot/dts/ti/k3-am654-base-board.dts |   42 +
 .../dts/ti/k3-j721e-common-proc-board.dts     |   43 +
 .../boot/dts/ti/k3-j721e-mcu-wakeup.dtsi      |   49 +
 arch/arm64/boot/dts/ti/k3-j721e.dtsi          |    1 +
 arch/arm64/configs/defconfig                  |    3 +
 drivers/net/ethernet/ti/Kconfig               |   20 +-
 drivers/net/ethernet/ti/Makefile              |    3 +
 drivers/net/ethernet/ti/am65-cpsw-ethtool.c   |  747 +++++++
 drivers/net/ethernet/ti/am65-cpsw-nuss.c      | 1965 +++++++++++++++++
 drivers/net/ethernet/ti/am65-cpsw-nuss.h      |  143 ++
 drivers/net/ethernet/ti/cpsw_ale.c            |   38 +
 drivers/net/ethernet/ti/cpsw_ale.h            |    4 +
 drivers/net/ethernet/ti/k3-udma-desc-pool.c   |  126 ++
 drivers/net/ethernet/ti/k3-udma-desc-pool.h   |   30 +
 drivers/phy/ti/Kconfig                        |    3 -
 18 files changed, 3488 insertions(+), 5 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/net/ti,k3-am654-cpsw-nuss.yaml
 create mode 100644 drivers/net/ethernet/ti/am65-cpsw-ethtool.c
 create mode 100644 drivers/net/ethernet/ti/am65-cpsw-nuss.c
 create mode 100644 drivers/net/ethernet/ti/am65-cpsw-nuss.h
 create mode 100644 drivers/net/ethernet/ti/k3-udma-desc-pool.c
 create mode 100644 drivers/net/ethernet/ti/k3-udma-desc-pool.h

Comments

Murali Karicheri March 19, 2020, 1:12 p.m. UTC | #1 
On 03/17/2020 03:27 AM, Grygorii Strashko wrote:
> Hi
> 
> This v4 series adds basic networking support support TI K3 AM654x/J721E SoC which
> have integrated Gigabit Ethernet MAC (Media Access Controller) into device MCU
> domain and named MCU_CPSW0 (CPSW2G NUSS).
> 
> Formally TRMs refer CPSW2G NUSS as two-port Gigabit Ethernet Switch subsystem
> with port 0 being the CPPI DMA host port and port 1 being the external Ethernet
> port, but for 1 external port device it's just Port 0 <-> ALE <-> Port 1 and it's
> rather device with HW filtering capabilities then actually switching device.
> It's expected to have similar devices, but with more external ports.
> 
> The new Host port 0 Communications Port Programming Interface (CPPI5) is
> operating by TI AM654x/J721E NAVSS Unified DMA Peripheral Root Complex (UDMA-P)
> controller [1].
> 
> The CPSW2G contains below modules for which existing code is re-used:
>   - MAC SL: cpsw_sl.c
>   - Address Lookup Engine (ALE): cpsw_ale.c, basically compatible with K2 66AK2E/G
>   - Management Data Input/Output interface (MDIO): davinci_mdio.c, fully
>     compatible with TI AM3/4/5 devices
> 
> Basic features supported by CPSW2G NUSS driver:
>   - VLAN support, 802.1Q compliant, Auto add port VLAN for untagged frames on
>     ingress, Auto VLAN removal on egress and auto pad to minimum frame size.
>   - multicast filtering
>   - promisc mode
>   - TX multiq support in Round Robin or Fixed priority modes
>   - RX checksum offload for non-fragmented IPv4/IPv6 TCP/UDP packets
>   - TX checksum offload support for IPv4/IPv6 TCP/UDP packets (J721E only).
> 
> Features under development:
>   - Support for IEEE 1588 Clock Synchronization. The CPSW2G NUSS includes new
>     version of Common Platform Time Sync (CPTS)
>   - tc-mqprio: priority level Quality Of Service (QOS) support (802.1p)
>   - tc-cbs: Support for Audio/Video Bridging (P802.1Qav/D6.0) HW shapers
>   - tc-taprio: IEEE 802.1Qbv/D2.2 Enhancements for Scheduled Traffic
>   - frame preemption: IEEE P902.3br/D2.0 Interspersing Express Traffic, 802.1Qbu
>   - extended ALE features: classifier/policers, auto-aging
> 
> Patches 1-6 are intended for netdev, Patches 7-11 are intended for K3 Platform
> tree and provided here for testing purposes.
> 
> Changes in v4:
>   - fixed minor comments from Jakub Kicinski <kuba@kernel.org>
>   - dependencies resolved: required phy-rmii-sel changes [2] queued for merge
>     except one [3] which is included in this series with Kishon's ask.
> 

Tested-by: Murali Karicheri <m-karicheri2@ti.com>

Logs at https://pastebin.ubuntu.com/p/rP6pcMqcw5/

> Changes in v3:
>   - add ARM64 defconfig changes for testing purposes
>   - fixed DT yaml definition
>   - fixed comments from Jakub Kicinski <kuba@kernel.org>
> 
> Changes in v2:
>   - fixed DT yaml definition
>   - fixed comments from David Miller
> 
> v3: https://patchwork.ozlabs.org/cover/1254568/
> v2: https://patchwork.ozlabs.org/cover/1250674/
> v1: https://lwn.net/Articles/813087/
> 
> TRMs:
>   AM654: http://www.ti.com/lit/ug/spruid7e/spruid7e.pdf
>   J721E: http://www.ti.com/lit/ug/spruil1a/spruil1a.pdf
> 
> Preliminary documentation can be found at:
>   http://software-dl.ti.com/processor-sdk-linux/esd/docs/latest/linux/Foundational_Components/Kernel/Kernel_Drivers/Network/K3_CPSW2g.html
> 
> [1] https://lwn.net/Articles/808030/
> [2] https://lkml.org/lkml/2020/2/22/100
> [3] https://lkml.org/lkml/2020/3/3/724
> 
> Grygorii Strashko (11):
>    phy: ti: gmii-sel: simplify config dependencies between net drivers
>      and gmii phy
>    net: ethernet: ti: ale: fix seeing unreg mcast packets with promisc
>      and allmulti disabled
>    net: ethernet: ti: ale: add support for mac-only mode
>    net: ethernet: ti: ale: am65: add support for default thread cfg
>    dt-binding: ti: am65x: document mcu cpsw nuss
>    net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver
>    arm64: dts: ti: k3-am65-mcu: add cpsw nuss node
>    arm64: dts: k3-am654-base-board: add mcu cpsw nuss pinmux and phy defs
>    arm64: dts: ti: k3-j721e-mcu: add mcu cpsw nuss node
>    arm64: dts: ti: k3-j721e-common-proc-board: add mcu cpsw nuss pinmux
>      and phy defs
>    arm64: defconfig: ti: k3: enable dma and networking
> 
>   .../bindings/net/ti,k3-am654-cpsw-nuss.yaml   |  226 ++
>   arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi       |   49 +
>   arch/arm64/boot/dts/ti/k3-am65.dtsi           |    1 +
>   .../arm64/boot/dts/ti/k3-am654-base-board.dts |   42 +
>   .../dts/ti/k3-j721e-common-proc-board.dts     |   43 +
>   .../boot/dts/ti/k3-j721e-mcu-wakeup.dtsi      |   49 +
>   arch/arm64/boot/dts/ti/k3-j721e.dtsi          |    1 +
>   arch/arm64/configs/defconfig                  |    3 +
>   drivers/net/ethernet/ti/Kconfig               |   20 +-
>   drivers/net/ethernet/ti/Makefile              |    3 +
>   drivers/net/ethernet/ti/am65-cpsw-ethtool.c   |  747 +++++++
>   drivers/net/ethernet/ti/am65-cpsw-nuss.c      | 1965 +++++++++++++++++
>   drivers/net/ethernet/ti/am65-cpsw-nuss.h      |  143 ++
>   drivers/net/ethernet/ti/cpsw_ale.c            |   38 +
>   drivers/net/ethernet/ti/cpsw_ale.h            |    4 +
>   drivers/net/ethernet/ti/k3-udma-desc-pool.c   |  126 ++
>   drivers/net/ethernet/ti/k3-udma-desc-pool.h   |   30 +
>   drivers/phy/ti/Kconfig                        |    3 -
>   18 files changed, 3488 insertions(+), 5 deletions(-)
>   create mode 100644 Documentation/devicetree/bindings/net/ti,k3-am654-cpsw-nuss.yaml
>   create mode 100644 drivers/net/ethernet/ti/am65-cpsw-ethtool.c
>   create mode 100644 drivers/net/ethernet/ti/am65-cpsw-nuss.c
>   create mode 100644 drivers/net/ethernet/ti/am65-cpsw-nuss.h
>   create mode 100644 drivers/net/ethernet/ti/k3-udma-desc-pool.c
>   create mode 100644 drivers/net/ethernet/ti/k3-udma-desc-pool.h
>