[v2,0/3] arm64: dts: imx8mp: add support for the ABB SoM and carrier

Message

Heiko Schocher Oct. 31, 2024, 3:12 p.m. UTC

The board uses an ABB specific SoM from ADLink, based on NXP
i.MX8MP SoC. The SoM is used on 3 different carrier boards,
with small differences.

series is based on:
819837584309 - (tag: v6.12-rc5, origin/master, origin/HEAD) Linux 6.12-rc5

patches are now checked with

make W=1 dt_binding_check
make W=1 dtbs_check
make W=1 CHECK_DTBS=y {for each dtb introduced in this series)

as Krzysztof suggested.

Changes in v2:
- worked in comments from Krzysztof
  - reworked the compatible strings for ABB imx8mp based boards
  - removed unneeded dtbos and build now dtbs for each
    carrierboard.
  - removed user spidev entries, as I do not know the
    real spi devices connected to...
  - call dtb check targets as described in cover letter
    and fixed warnings except warnings see below:
not fixed dtb check warnings
- pci (warning pops up for each new dtb from this patch, but
  also for a lot of other boards, which are already in tree)
imx8mp-aristainetos3-adpismarc.dtb: pcie-ep@33800000: reg: [[864026624, 4194304], [402653184, 134217728]] is too short
        from schema $id: http://devicetree.org/schemas/pci/fsl,imx6q-pcie-ep.yaml#
imx8mp-aristainetos3-adpismarc.dtb: pcie-ep@33800000: reg-names: ['dbi', 'addr_space'] is too short
        from schema $id: http://devicetree.org/schemas/pci/fsl,imx6q-pcie-ep.yaml#
- proton2s dtb specific:
  - rs485
    imx8mp-aristainetos3-proton2s.dtb: serial@30a60000: rs485-rts-delay:0: 0 is not of type 'array'
        from schema $id: http://devicetree.org/schemas/serial/fsl-imx-uart.yaml#
    imx8mp-aristainetos3-proton2s.dtb: serial@30a60000: rs485-rts-delay:1: 0 is not of type 'array'
        from schema $id: http://devicetree.org/schemas/serial/fsl-imx-uart.yaml#
    imx8mp-aristainetos3-proton2s.dtb: serial@30a60000: Unevaluated properties are not allowed ('linux,rs485-enabled-at-boot-time', 'rs485-rts-active-low', 'rs485-rts-delay' were unexpected)
        from schema $id: http://devicetree.org/schemas/serial/fsl-imx-uart.yaml#
    do not see, what I am doing wrong, also rs485 works fine
  - led driver
    imx8mp-aristainetos3-proton2s.dtb: /soc@0/bus@30800000/i2c@30a30000/tlc59108@40: failed to match any schema with compatible: ['ti,tlc59108']
    I use the comaptible entry used in drivers/leds/leds-tlc591xx.c
    Ah, may because file
    Documentation/devicetree/bindings/leds/leds-tlc591xx.txt
    is not converted to yaml?
  - pinctrl driver
    adding 'gpio-line-names' leads in a warning as this property
    is not checked yet (and so a warning is dropped).
    add this check in new patch
    dt-bindings: pinctrl: sx150xq: allow gpio line naming
    in v2

Heiko Schocher (3):
  dt-bindings: arm: fsl: Add ABB SoM and carrier
  dt-bindings: pinctrl: sx150xq: allow gpio line naming
  arm64: dts: imx8mp: add aristainetos3 board support

 .../devicetree/bindings/arm/fsl.yaml          |    9 +
 .../bindings/pinctrl/semtech,sx1501q.yaml     |    4 +
 arch/arm64/boot/dts/freescale/Makefile        |    5 +
 .../imx8mp-aristainetos3-adpismarc.dts        |   38 +
 .../imx8mp-aristainetos3-helios-lvds.dtso     |  115 ++
 .../freescale/imx8mp-aristainetos3-helios.dts |   99 ++
 .../imx8mp-aristainetos3-proton2s.dts         |  162 +++
 .../imx8mp-aristainetos3a-som-v1.dtsi         | 1116 +++++++++++++++++
 8 files changed, 1548 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtso
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dtsi