@@ -496,7 +496,8 @@ dtb-$(CONFIG_MACH_ARMADA_370) += \
armada-370-mirabox.dtb \
armada-370-netgear-rn102.dtb \
armada-370-netgear-rn104.dtb \
- armada-370-rd.dtb
+ armada-370-rd.dtb \
+ armada-370-synology-ds213j.dtb
dtb-$(CONFIG_MACH_ARMADA_375) += \
armada-375-db.dtb
dtb-$(CONFIG_MACH_ARMADA_38X) += \
new file mode 100644
@@ -0,0 +1,321 @@
+/*
+ * Device Tree file for Synology DS213j
+ *
+ * Copyright (C) 2014, Arnaud EBALARD <arno@natisbad.org>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the old 0xd0000000).
+ * The 0xf1000000 is the default used by the recent, DT-capable, U-Boot
+ * bootloaders provided by Marvell. It is used in recent versions of
+ * DSM software provided by Synology. Nonetheless, some earlier boards
+ * were delivered with an older version of u-boot that left internal
+ * registers mapped at 0xd0000000. If you have such a device you will
+ * not be able to directly boot a kernel based on this Device Tree. In
+ * that case, the preferred solution is to update your bootloader (e.g.
+ * by upgrading to latest version of DSM, or building a new one and
+ * installing it from u-boot prompt) or adjust the Devive Tree
+ * (s/0xf1000000/0xd0000000/ in 'ranges' below).
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-370.dtsi"
+
+/ {
+ model = "Synology DS213j";
+ compatible = "synology,ds213j", "marvell,armada370",
+ "marvell,armada-370-xp";
+
+ chosen {
+ bootargs = "console=ttyS0,115200 earlyprintk";
+ stdout-path = &uart0;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>; /* 512 MB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+ MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>;
+
+ internal-regs {
+
+ sata@a0000 {
+ nr-ports = <2>;
+ status = "okay";
+ };
+
+ mdio {
+ phy1: ethernet-phy@1 { /* Marvell 88E1512 */
+ reg = <1>;
+ };
+ };
+
+ ethernet@70000 {
+ status = "okay";
+ phy = <&phy1>;
+ phy-mode = "sgmii";
+ };
+
+ spi0: spi@10600 {
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "micron,n25q064";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <20000000>;
+
+ /*
+ * Warning!
+ *
+ * Synology u-boot uses its compiled-in environment
+ * and it seems Synology did not care to change u-boot
+ * default configuration in order to allow saving a
+ * modified environment at a sensible location. So,
+ * if you do a 'saveenv' under u-boot, your modified
+ * environment will be saved at 1MB after the start
+ * of the flash, i.e. in the middle of the uImage.
+ * For that reason, it is strongly advised not to
+ * change the default environment, unless you know
+ * what you are doing.
+ */
+ partition@00000000 { /* u-boot */
+ label = "RedBoot";
+ reg = <0x00000000 0x000c0000>; /* 768KB */
+ };
+
+ partition@000c0000 { /* uImage */
+ label = "zImage";
+ reg = <0x000c0000 0x002d0000>; /* 2880KB */
+ };
+
+ partition@00390000 { /* uInitramfs */
+ label = "rd.gz";
+ reg = <0x00390000 0x00440000>; /* 4250KB */
+ };
+
+ partition@007d0000 { /* MAC address and serial number */
+ label = "vendor";
+ reg = <0x007d0000 0x00010000>; /* 64KB */
+ };
+
+ partition@007e0000 {
+ label = "RedBoot config";
+ reg = <0x007e0000 0x00010000>; /* 64KB */
+ };
+
+ partition@007f0000 {
+ label = "FIS directory";
+ reg = <0x007f0000 0x00010000>; /* 64KB */
+ };
+ };
+ };
+
+ /* rear USB port, near reset button */
+ usb@50000 {
+ status = "okay";
+ };
+
+ /* rear USB port, near RJ45 port */
+ usb@51000 {
+ status = "okay";
+ };
+
+ i2c@11000 {
+ compatible = "marvell,mv64xxx-i2c";
+ pinctrl-0 = <&i2c0_pins>;
+ pinctrl-names = "default";
+ clock-frequency = <400000>;
+ status = "okay";
+
+ /* Main device RTC chip */
+ s35390a: s35390a@30 {
+ compatible = "sii,s35390a";
+ reg = <0x30>;
+ };
+ };
+
+ /* RTC provided by Seiko S-35390A above */
+ rtc@10300 {
+ status = "disabled";
+ };
+
+ /* Connected to a header on device's PCB */
+ serial@12000 {
+ status = "okay";
+ };
+
+ /* Connected to a TI MSP430F2111 for power control */
+ serial@12100 {
+ status = "okay";
+ };
+
+ poweroff@12100 {
+ compatible = "synology,power-off";
+ reg = <0x12100 0x100>;
+ clocks = <&coreclk 0>;
+ };
+ };
+ };
+
+ gpio-fan-32-38 {
+ status = "okay";
+ compatible = "gpio-fan";
+ pinctrl-0 = <&fan_ctrl_low_pin &fan_ctrl_mid_pin
+ &fan_ctrl_high_pin &fan_alarm_pin>;
+ pinctrl-names = "default";
+ gpios = <&gpio1 31 GPIO_ACTIVE_HIGH
+ &gpio2 0 GPIO_ACTIVE_HIGH
+ &gpio2 1 GPIO_ACTIVE_HIGH>;
+ alarm-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+ gpio-fan,speed-map = < 0 0
+ 1000 1
+ 1150 2
+ 1350 4
+ 1500 3
+ 1650 5
+ 1750 6
+ 1900 7 >;
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&disk1_led_pin
+ &disk2_led_pin>;
+ pinctrl-names = "default";
+
+ disk1-led-amber {
+ label = "synology:amber:disk1";
+ gpios = <&gpio0 31 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ };
+
+ disk2-led-amber {
+ label = "synology:amber:disk2";
+ gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&sata1_pwr_pin &sata2_pwr_pin>;
+ pinctrl-names = "default";
+
+ sata1_regulator: sata1-regulator {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "SATA1 Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ startup-delay-us = <2000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+ };
+
+ sata2_regulator: sata2-regulator {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "SATA2 Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ startup-delay-us = <4000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&pinctrl {
+ disk1_led_pin: disk1-led-pin {
+ marvell,pins = "mpp31";
+ marvell,function = "gpio";
+ };
+
+ disk2_led_pin: disk2-led-pin {
+ marvell,pins = "mpp32";
+ marvell,function = "gpio";
+ };
+
+ sata1_pwr_pin: sata1-pwr-pin {
+ marvell,pins = "mpp37";
+ marvell,function = "gpio";
+ };
+
+ sata2_pwr_pin: sata2-pwr-pin {
+ marvell,pins = "mpp62";
+ marvell,function = "gpio";
+ };
+
+ sata1_pres_pin: sata1-pres-pin {
+ marvell,pins = "mpp60";
+ marvell,function = "gpio";
+ };
+
+ sata2_pres_pin: sata2-pres-pin {
+ marvell,pins = "mpp48";
+ marvell,function = "gpio";
+ };
+
+ syno_id_bit0_pin: syno-id-bit0-pin {
+ marvell,pins = "mpp55";
+ marvell,function = "gpio";
+ };
+
+ syno_id_bit1_pin: syno-id-bit1-pin {
+ marvell,pins = "mpp56";
+ marvell,function = "gpio";
+ };
+
+ syno_id_bit2_pin: syno-id-bit2-pin {
+ marvell,pins = "mpp57";
+ marvell,function = "gpio";
+ };
+
+ syno_id_bit3_pin: syno-id-bit3-pin {
+ marvell,pins = "mpp58";
+ marvell,function = "gpio";
+ };
+
+ fan_ctrl_low_pin: fan-ctrl-low-pin {
+ marvell,pins = "mpp65";
+ marvell,function = "gpio";
+ };
+
+ fan_ctrl_mid_pin: fan-ctrl-mid-pin {
+ marvell,pins = "mpp64";
+ marvell,function = "gpio";
+ };
+
+ fan_ctrl_high_pin: fan-ctrl-high-pin {
+ marvell,pins = "mpp63";
+ marvell,function = "gpo";
+ };
+
+ fan_alarm_pin: fan-alarm-pin {
+ marvell,pins = "mpp38";
+ marvell,function = "gpio";
+ };
+
+ poweroff_pin: poweroff-pin {
+ marvell,pins = "mpp4";
+ marvell,function = "gpio";
+ };
+};
Synology DS213j is a 2-bay NAS powered by a Marvell Armada 370 (88F6710 @1.2Ghz). It is very similar on many aspects to previous 2-bay synology models based on Marvell kirkwood SoC. Here is a short summary of the device: - 512MB RAM - boot on SPI flash (64Mbit Micron N25Q064) - 1 GbE interface (Armada MAC connected to a Marvell 88E1512 PHY via SGMII) - 2 rear USB 2.0 ports (directly handled by the Armada 370) - 2 internal SATA ports handled by the Armada 370: 2 GPIO for presence, 2 for powering them - two front amber LED (disk1, disk2) controlled by the SoC - Seiko S-35390A I2C RTC chip - UART0 providing serial console - UART1 used for poweroff (connected to a TI MSP430F2111) - Fan handled via 4 GPIO (3 for speed, 1 for alarm) Signed-off-by: Arnaud Ebalard <arno@natisbad.org> --- arch/arm/boot/dts/Makefile | 3 +- arch/arm/boot/dts/armada-370-synology-ds213j.dts | 321 +++++++++++++++++++++++ 2 files changed, 323 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/armada-370-synology-ds213j.dts