@@ -37,6 +37,7 @@ obj-$(CONFIG_GPIO_PCF857X) += gpio-pcf857x.o
obj-$(CONFIG_GPIO_PCH) += gpio-pch.o
obj-$(CONFIG_GPIO_PL061) += gpio-pl061.o
obj-$(CONFIG_GPIO_RDC321X) += gpio-rdc321x.o
+obj-$(CONFIG_PLAT_SAMSUNG) += gpio-samsung.o
obj-$(CONFIG_GPIO_SCH) += gpio-sch.o
obj-$(CONFIG_GPIO_STMPE) += gpio-stmpe.o
obj-$(CONFIG_GPIO_SX150X) += gpio-sx150x.o
new file mode 100644
@@ -0,0 +1,2686 @@
+/*
+ * Copyright (c) 2009-2011 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com/
+ *
+ * Copyright 2008 Openmoko, Inc.
+ * Copyright 2008 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
+ * http://armlinux.simtec.co.uk/
+ *
+ * SAMSUNG - GPIOlib support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/irq.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/spinlock.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/sysdev.h>
+#include <linux/ioport.h>
+
+#include <asm/irq.h>
+
+#include <mach/hardware.h>
+#include <mach/map.h>
+#include <mach/regs-clock.h>
+#include <mach/regs-gpio.h>
+
+#include <plat/cpu.h>
+#include <plat/gpio-core.h>
+#include <plat/gpio-cfg.h>
+#include <plat/gpio-cfg-helpers.h>
+#include <plat/gpio-fns.h>
+#include <plat/pm.h>
+
+#ifndef DEBUG_GPIO
+#define gpio_dbg(x...) do { } while (0)
+#else
+#define gpio_dbg(x...) printk(KERN_DEBUG x)
+#endif
+
+int samsung_gpio_setpull_updown(struct samsung_gpio_chip *chip,
+ unsigned int off, samsung_gpio_pull_t pull)
+{
+ void __iomem *reg = chip->base + 0x08;
+ int shift = off * 2;
+ u32 pup;
+
+ pup = __raw_readl(reg);
+ pup &= ~(3 << shift);
+ pup |= pull << shift;
+ __raw_writel(pup, reg);
+
+ return 0;
+}
+
+samsung_gpio_pull_t samsung_gpio_getpull_updown(struct samsung_gpio_chip *chip,
+ unsigned int off)
+{
+ void __iomem *reg = chip->base + 0x08;
+ int shift = off * 2;
+ u32 pup = __raw_readl(reg);
+
+ pup >>= shift;
+ pup &= 0x3;
+
+ return (__force samsung_gpio_pull_t)pup;
+}
+
+int s3c2443_gpio_setpull(struct samsung_gpio_chip *chip,
+ unsigned int off, samsung_gpio_pull_t pull)
+{
+ switch (pull) {
+ case S3C_GPIO_PULL_NONE:
+ pull = 0x01;
+ break;
+ case S3C_GPIO_PULL_UP:
+ pull = 0x00;
+ break;
+ case S3C_GPIO_PULL_DOWN:
+ pull = 0x02;
+ break;
+ }
+ return samsung_gpio_setpull_updown(chip, off, pull);
+}
+
+samsung_gpio_pull_t s3c2443_gpio_getpull(struct samsung_gpio_chip *chip,
+ unsigned int off)
+{
+ samsung_gpio_pull_t pull;
+
+ pull = samsung_gpio_getpull_updown(chip, off);
+
+ switch (pull) {
+ case 0x00:
+ pull = S3C_GPIO_PULL_UP;
+ break;
+ case 0x01:
+ case 0x03:
+ pull = S3C_GPIO_PULL_NONE;
+ break;
+ case 0x02:
+ pull = S3C_GPIO_PULL_DOWN;
+ break;
+ }
+
+ return pull;
+}
+
+static int s3c24xx_gpio_setpull_1(struct samsung_gpio_chip *chip,
+ unsigned int off, samsung_gpio_pull_t pull,
+ samsung_gpio_pull_t updown)
+{
+ void __iomem *reg = chip->base + 0x08;
+ u32 pup = __raw_readl(reg);
+
+ if (pull == updown)
+ pup &= ~(1 << off);
+ else if (pull == S3C_GPIO_PULL_NONE)
+ pup |= (1 << off);
+ else
+ return -EINVAL;
+
+ __raw_writel(pup, reg);
+ return 0;
+}
+
+static samsung_gpio_pull_t s3c24xx_gpio_getpull_1(struct samsung_gpio_chip *chip,
+ unsigned int off,
+ samsung_gpio_pull_t updown)
+{
+ void __iomem *reg = chip->base + 0x08;
+ u32 pup = __raw_readl(reg);
+
+ pup &= (1 << off);
+ return pup ? S3C_GPIO_PULL_NONE : updown;
+}
+
+samsung_gpio_pull_t s3c24xx_gpio_getpull_1up(struct samsung_gpio_chip *chip,
+ unsigned int off)
+{
+ return s3c24xx_gpio_getpull_1(chip, off, S3C_GPIO_PULL_UP);
+}
+
+int s3c24xx_gpio_setpull_1up(struct samsung_gpio_chip *chip,
+ unsigned int off, samsung_gpio_pull_t pull)
+{
+ return s3c24xx_gpio_setpull_1(chip, off, pull, S3C_GPIO_PULL_UP);
+}
+
+samsung_gpio_pull_t s3c24xx_gpio_getpull_1down(struct samsung_gpio_chip *chip,
+ unsigned int off)
+{
+ return s3c24xx_gpio_getpull_1(chip, off, S3C_GPIO_PULL_DOWN);
+}
+
+int s3c24xx_gpio_setpull_1down(struct samsung_gpio_chip *chip,
+ unsigned int off, samsung_gpio_pull_t pull)
+{
+ return s3c24xx_gpio_setpull_1(chip, off, pull, S3C_GPIO_PULL_DOWN);
+}
+
+static int exynos4_gpio_setpull(struct samsung_gpio_chip *chip,
+ unsigned int off, samsung_gpio_pull_t pull)
+{
+ if (pull == S3C_GPIO_PULL_UP)
+ pull = 3;
+
+ return samsung_gpio_setpull_updown(chip, off, pull);
+}
+
+static samsung_gpio_pull_t exynos4_gpio_getpull(struct samsung_gpio_chip *chip,
+ unsigned int off)
+{
+ samsung_gpio_pull_t pull;
+
+ pull = samsung_gpio_getpull_updown(chip, off);
+
+ if (pull == 3)
+ pull = S3C_GPIO_PULL_UP;
+
+ return pull;
+}
+
+/*
+ * samsung_gpio_setcfg_2bit - Samsung 2bit style GPIO configuration.
+ * @chip: The gpio chip that is being configured.
+ * @off: The offset for the GPIO being configured.
+ * @cfg: The configuration value to set.
+ *
+ * This helper deal with the GPIO cases where the control register
+ * has two bits of configuration per gpio, which have the following
+ * functions:
+ * 00 = input
+ * 01 = output
+ * 1x = special function
+ */
+
+static int samsung_gpio_setcfg_2bit(struct samsung_gpio_chip *chip,
+ unsigned int off, unsigned int cfg)
+{
+ void __iomem *reg = chip->base;
+ unsigned int shift = off * 2;
+ u32 con;
+
+ if (samsung_gpio_is_cfg_special(cfg)) {
+ cfg &= 0xf;
+ if (cfg > 3)
+ return -EINVAL;
+
+ cfg <<= shift;
+ }
+
+ con = __raw_readl(reg);
+ con &= ~(0x3 << shift);
+ con |= cfg;
+ __raw_writel(con, reg);
+
+ return 0;
+}
+
+/*
+ * samsung_gpio_getcfg_2bit - Samsung 2bit style GPIO configuration read.
+ * @chip: The gpio chip that is being configured.
+ * @off: The offset for the GPIO being configured.
+ *
+ * The reverse of samsung_gpio_setcfg_2bit(). Will return a value whicg
+ * could be directly passed back to samsung_gpio_setcfg_2bit(), from the
+ * S3C_GPIO_SPECIAL() macro.
+ */
+
+static unsigned int samsung_gpio_getcfg_2bit(struct samsung_gpio_chip *chip,
+ unsigned int off)
+{
+ u32 con;
+
+ con = __raw_readl(chip->base);
+ con >>= off * 2;
+ con &= 3;
+
+ /* this conversion works for IN and OUT as well as special mode */
+ return S3C_GPIO_SPECIAL(con);
+}
+
+/*
+ * samsung_gpio_setcfg_4bit - Samsung 4bit single register GPIO config.
+ * @chip: The gpio chip that is being configured.
+ * @off: The offset for the GPIO being configured.
+ * @cfg: The configuration value to set.
+ *
+ * This helper deal with the GPIO cases where the control register has 4 bits
+ * of control per GPIO, generally in the form of:
+ * 0000 = Input
+ * 0001 = Output
+ * others = Special functions (dependent on bank)
+ *
+ * Note, since the code to deal with the case where there are two control
+ * registers instead of one, we do not have a separate set of functions for
+ * each case.
+ */
+
+static int samsung_gpio_setcfg_4bit(struct samsung_gpio_chip *chip,
+ unsigned int off, unsigned int cfg)
+{
+ void __iomem *reg = chip->base;
+ unsigned int shift = (off & 7) * 4;
+ u32 con;
+
+ if (off < 8 && chip->chip.ngpio > 8)
+ reg -= 4;
+
+ if (samsung_gpio_is_cfg_special(cfg)) {
+ cfg &= 0xf;
+ cfg <<= shift;
+ }
+
+ con = __raw_readl(reg);
+ con &= ~(0xf << shift);
+ con |= cfg;
+ __raw_writel(con, reg);
+
+ return 0;
+}
+
+/*
+ * samsung_gpio_getcfg_4bit - Samsung 4bit single register GPIO config read.
+ * @chip: The gpio chip that is being configured.
+ * @off: The offset for the GPIO being configured.
+ *
+ * The reverse of samsung_gpio_setcfg_4bit(), turning a gpio configuration
+ * register setting into a value the software can use, such as could be passed
+ * to samsung_gpio_setcfg_4bit().
+ *
+ * @sa samsung_gpio_getcfg_2bit
+ */
+
+static unsigned samsung_gpio_getcfg_4bit(struct samsung_gpio_chip *chip,
+ unsigned int off)
+{
+ void __iomem *reg = chip->base;
+ unsigned int shift = (off & 7) * 4;
+ u32 con;
+
+ if (off < 8 && chip->chip.ngpio > 8)
+ reg -= 4;
+
+ con = __raw_readl(reg);
+ con >>= shift;
+ con &= 0xf;
+
+ /* this conversion works for IN and OUT as well as special mode */
+ return S3C_GPIO_SPECIAL(con);
+}
+
+/*
+ * s3c24xx_gpio_setcfg_abank - S3C24XX style GPIO configuration (Bank A)
+ * @chip: The gpio chip that is being configured.
+ * @off: The offset for the GPIO being configured.
+ * @cfg: The configuration value to set.
+ *
+ * This helper deal with the GPIO cases where the control register
+ * has one bit of configuration for the gpio, where setting the bit
+ * means the pin is in special function mode and unset means output.
+ */
+
+static int s3c24xx_gpio_setcfg_abank(struct samsung_gpio_chip *chip,
+ unsigned int off, unsigned int cfg)
+{
+ void __iomem *reg = chip->base;
+ unsigned int shift = off;
+ u32 con;
+
+ if (samsung_gpio_is_cfg_special(cfg)) {
+ cfg &= 0xf;
+
+ /* Map output to 0, and SFN2 to 1 */
+ cfg -= 1;
+ if (cfg > 1)
+ return -EINVAL;
+
+ cfg <<= shift;
+ }
+
+ con = __raw_readl(reg);
+ con &= ~(0x1 << shift);
+ con |= cfg;
+ __raw_writel(con, reg);
+
+ return 0;
+}
+
+/*
+ * s3c24xx_gpio_getcfg_abank - S3C24XX style GPIO configuration read (Bank A)
+ * @chip: The gpio chip that is being configured.
+ * @off: The offset for the GPIO being configured.
+ *
+ * The reverse of s3c24xx_gpio_setcfg_abank() turning an GPIO into a usable
+ * GPIO configuration value.
+ *
+ * @sa samsung_gpio_getcfg_2bit
+ * @sa samsung_gpio_getcfg_4bit
+ */
+
+static unsigned s3c24xx_gpio_getcfg_abank(struct samsung_gpio_chip *chip,
+ unsigned int off)
+{
+ u32 con;
+
+ con = __raw_readl(chip->base);
+ con >>= off;
+ con &= 1;
+ con++;
+
+ return S3C_GPIO_SFN(con);
+}
+
+static int s5p64x0_gpio_setcfg_rbank(struct samsung_gpio_chip *chip,
+ unsigned int off, unsigned int cfg)
+{
+ void __iomem *reg = chip->base;
+ unsigned int shift;
+ u32 con;
+
+ switch (off) {
+ case 0:
+ case 1:
+ case 2:
+ case 3:
+ case 4:
+ case 5:
+ shift = (off & 7) * 4;
+ reg -= 4;
+ break;
+ case 6:
+ shift = ((off + 1) & 7) * 4;
+ reg -= 4;
+ default:
+ shift = ((off + 1) & 7) * 4;
+ break;
+ }
+
+ if (samsung_gpio_is_cfg_special(cfg)) {
+ cfg &= 0xf;
+ cfg <<= shift;
+ }
+
+ con = __raw_readl(reg);
+ con &= ~(0xf << shift);
+ con |= cfg;
+ __raw_writel(con, reg);
+
+ return 0;
+}
+
+static void __init samsung_gpiolib_set_cfg(struct samsung_gpio_cfg *chipcfg,
+ int nr_chips)
+{
+ for (; nr_chips > 0; nr_chips--, chipcfg++) {
+ if (!chipcfg->set_config)
+ chipcfg->set_config = samsung_gpio_setcfg_4bit;
+ if (!chipcfg->get_config)
+ chipcfg->get_config = samsung_gpio_getcfg_4bit;
+ if (!chipcfg->set_pull)
+ chipcfg->set_pull = samsung_gpio_setpull_updown;
+ if (!chipcfg->get_pull)
+ chipcfg->get_pull = samsung_gpio_getpull_updown;
+ }
+}
+
+struct samsung_gpio_cfg s3c24xx_gpiocfg_default = {
+ .set_config = samsung_gpio_setcfg_2bit,
+ .get_config = samsung_gpio_getcfg_2bit,
+};
+
+static struct samsung_gpio_cfg s3c24xx_gpiocfg_banka = {
+ .set_config = s3c24xx_gpio_setcfg_abank,
+ .get_config = s3c24xx_gpio_getcfg_abank,
+};
+
+static struct samsung_gpio_cfg exynos4_gpio_cfg = {
+ .set_pull = exynos4_gpio_setpull,
+ .get_pull = exynos4_gpio_getpull,
+};
+
+static struct samsung_gpio_cfg s5p64x0_gpio_cfg_rbank = {
+ .cfg_eint = 0x3,
+ .set_config = s5p64x0_gpio_setcfg_rbank,
+ .get_config = samsung_gpio_getcfg_4bit,
+ .set_pull = samsung_gpio_setpull_updown,
+ .get_pull = samsung_gpio_getpull_updown,
+};
+
+static struct samsung_gpio_cfg samsung_gpio_cfgs[] = {
+ {
+ .cfg_eint = 0x0,
+ }, {
+ .cfg_eint = 0x3,
+ }, {
+ .cfg_eint = 0x7,
+ }, {
+ .cfg_eint = 0xF,
+ }, {
+ .cfg_eint = 0x0,
+ .set_config = samsung_gpio_setcfg_2bit,
+ .get_config = samsung_gpio_getcfg_2bit,
+ }, {
+ .cfg_eint = 0x2,
+ .set_config = samsung_gpio_setcfg_2bit,
+ .get_config = samsung_gpio_getcfg_2bit,
+ }, {
+ .cfg_eint = 0x3,
+ .set_config = samsung_gpio_setcfg_2bit,
+ .get_config = samsung_gpio_getcfg_2bit,
+ }, {
+ .set_config = samsung_gpio_setcfg_2bit,
+ .get_config = samsung_gpio_getcfg_2bit,
+ },
+};
+
+/*
+ * Default routines for controlling GPIO, based on the original S3C24XX
+ * GPIO functions which deal with the case where each gpio bank of the
+ * chip is as following:
+ *
+ * base + 0x00: Control register, 2 bits per gpio
+ * gpio n: 2 bits starting at (2*n)
+ * 00 = input, 01 = output, others mean special-function
+ * base + 0x04: Data register, 1 bit per gpio
+ * bit n: data bit n
+*/
+
+static int samsung_gpiolib_2bit_input(struct gpio_chip *chip, unsigned offset)
+{
+ struct samsung_gpio_chip *ourchip = to_samsung_gpio(chip);
+ void __iomem *base = ourchip->base;
+ unsigned long flags;
+ unsigned long con;
+
+ samsung_gpio_lock(ourchip, flags);
+
+ con = __raw_readl(base + 0x00);
+ con &= ~(3 << (offset * 2));
+
+ __raw_writel(con, base + 0x00);
+
+ samsung_gpio_unlock(ourchip, flags);
+ return 0;
+}
+
+static int samsung_gpiolib_2bit_output(struct gpio_chip *chip,
+ unsigned offset, int value)
+{
+ struct samsung_gpio_chip *ourchip = to_samsung_gpio(chip);
+ void __iomem *base = ourchip->base;
+ unsigned long flags;
+ unsigned long dat;
+ unsigned long con;
+
+ samsung_gpio_lock(ourchip, flags);
+
+ dat = __raw_readl(base + 0x04);
+ dat &= ~(1 << offset);
+ if (value)
+ dat |= 1 << offset;
+ __raw_writel(dat, base + 0x04);
+
+ con = __raw_readl(base + 0x00);
+ con &= ~(3 << (offset * 2));
+ con |= 1 << (offset * 2);
+
+ __raw_writel(con, base + 0x00);
+ __raw_writel(dat, base + 0x04);
+
+ samsung_gpio_unlock(ourchip, flags);
+ return 0;
+}
+
+/*
+ * The samsung_gpiolib_4bit routines are to control the gpio banks where
+ * the gpio configuration register (GPxCON) has 4 bits per GPIO, as the
+ * following example:
+ *
+ * base + 0x00: Control register, 4 bits per gpio
+ * gpio n: 4 bits starting at (4*n)
+ * 0000 = input, 0001 = output, others mean special-function
+ * base + 0x04: Data register, 1 bit per gpio
+ * bit n: data bit n
+ *
+ * Note, since the data register is one bit per gpio and is at base + 0x4
+ * we can use samsung_gpiolib_get and samsung_gpiolib_set to change the
+ * state of the output.
+ */
+
+static int samsung_gpiolib_4bit_input(struct gpio_chip *chip,
+ unsigned int offset)
+{
+ struct samsung_gpio_chip *ourchip = to_samsung_gpio(chip);
+ void __iomem *base = ourchip->base;
+ unsigned long con;
+
+ con = __raw_readl(base + GPIOCON_OFF);
+ con &= ~(0xf << con_4bit_shift(offset));
+ __raw_writel(con, base + GPIOCON_OFF);
+
+ gpio_dbg("%s: %p: CON now %08lx\n", __func__, base, con);
+
+ return 0;
+}
+
+static int samsung_gpiolib_4bit_output(struct gpio_chip *chip,
+ unsigned int offset, int value)
+{
+ struct samsung_gpio_chip *ourchip = to_samsung_gpio(chip);
+ void __iomem *base = ourchip->base;
+ unsigned long con;
+ unsigned long dat;
+
+ con = __raw_readl(base + GPIOCON_OFF);
+ con &= ~(0xf << con_4bit_shift(offset));
+ con |= 0x1 << con_4bit_shift(offset);
+
+ dat = __raw_readl(base + GPIODAT_OFF);
+
+ if (value)
+ dat |= 1 << offset;
+ else
+ dat &= ~(1 << offset);
+
+ __raw_writel(dat, base + GPIODAT_OFF);
+ __raw_writel(con, base + GPIOCON_OFF);
+ __raw_writel(dat, base + GPIODAT_OFF);
+
+ gpio_dbg("%s: %p: CON %08lx, DAT %08lx\n", __func__, base, con, dat);
+
+ return 0;
+}
+
+/*
+ * The next set of routines are for the case where the GPIO configuration
+ * registers are 4 bits per GPIO but there is more than one register (the
+ * bank has more than 8 GPIOs.
+ *
+ * This case is the similar to the 4 bit case, but the registers are as
+ * follows:
+ *
+ * base + 0x00: Control register, 4 bits per gpio (lower 8 GPIOs)
+ * gpio n: 4 bits starting at (4*n)
+ * 0000 = input, 0001 = output, others mean special-function
+ * base + 0x04: Control register, 4 bits per gpio (up to 8 additions GPIOs)
+ * gpio n: 4 bits starting at (4*n)
+ * 0000 = input, 0001 = output, others mean special-function
+ * base + 0x08: Data register, 1 bit per gpio
+ * bit n: data bit n
+ *
+ * To allow us to use the samsung_gpiolib_get and samsung_gpiolib_set
+ * routines we store the 'base + 0x4' address so that these routines see
+ * the data register at ourchip->base + 0x04.
+ */
+
+static int samsung_gpiolib_4bit2_input(struct gpio_chip *chip,
+ unsigned int offset)
+{
+ struct samsung_gpio_chip *ourchip = to_samsung_gpio(chip);
+ void __iomem *base = ourchip->base;
+ void __iomem *regcon = base;
+ unsigned long con;
+
+ if (offset > 7)
+ offset -= 8;
+ else
+ regcon -= 4;
+
+ con = __raw_readl(regcon);
+ con &= ~(0xf << con_4bit_shift(offset));
+ __raw_writel(con, regcon);
+
+ gpio_dbg("%s: %p: CON %08lx\n", __func__, base, con);
+
+ return 0;
+}
+
+static int samsung_gpiolib_4bit2_output(struct gpio_chip *chip,
+ unsigned int offset, int value)
+{
+ struct samsung_gpio_chip *ourchip = to_samsung_gpio(chip);
+ void __iomem *base = ourchip->base;
+ void __iomem *regcon = base;
+ unsigned long con;
+ unsigned long dat;
+ unsigned con_offset = offset;
+
+ if (con_offset > 7)
+ con_offset -= 8;
+ else
+ regcon -= 4;
+
+ con = __raw_readl(regcon);
+ con &= ~(0xf << con_4bit_shift(con_offset));
+ con |= 0x1 << con_4bit_shift(con_offset);
+
+ dat = __raw_readl(base + GPIODAT_OFF);
+
+ if (value)
+ dat |= 1 << offset;
+ else
+ dat &= ~(1 << offset);
+
+ __raw_writel(dat, base + GPIODAT_OFF);
+ __raw_writel(con, regcon);
+ __raw_writel(dat, base + GPIODAT_OFF);
+
+ gpio_dbg("%s: %p: CON %08lx, DAT %08lx\n", __func__, base, con, dat);
+
+ return 0;
+}
+
+/* The next set of routines are for the case of s3c24xx bank a */
+
+static int s3c24xx_gpiolib_banka_input(struct gpio_chip *chip, unsigned offset)
+{
+ return -EINVAL;
+}
+
+static int s3c24xx_gpiolib_banka_output(struct gpio_chip *chip,
+ unsigned offset, int value)
+{
+ struct samsung_gpio_chip *ourchip = to_samsung_gpio(chip);
+ void __iomem *base = ourchip->base;
+ unsigned long flags;
+ unsigned long dat;
+ unsigned long con;
+
+ local_irq_save(flags);
+
+ con = __raw_readl(base + 0x00);
+ dat = __raw_readl(base + 0x04);
+
+ dat &= ~(1 << offset);
+ if (value)
+ dat |= 1 << offset;
+
+ __raw_writel(dat, base + 0x04);
+
+ con &= ~(1 << offset);
+
+ __raw_writel(con, base + 0x00);
+ __raw_writel(dat, base + 0x04);
+
+ local_irq_restore(flags);
+ return 0;
+}
+
+/* The next set of routines are for the case of s5p64x0 bank r */
+
+static int s5p64x0_gpiolib_rbank_input(struct gpio_chip *chip,
+ unsigned int offset)
+{
+ struct samsung_gpio_chip *ourchip = to_samsung_gpio(chip);
+ void __iomem *base = ourchip->base;
+ void __iomem *regcon = base;
+ unsigned long con;
+ unsigned long flags;
+
+ switch (offset) {
+ case 6:
+ offset += 1;
+ case 0:
+ case 1:
+ case 2:
+ case 3:
+ case 4:
+ case 5:
+ regcon -= 4;
+ break;
+ default:
+ offset -= 7;
+ break;
+ }
+
+ samsung_gpio_lock(ourchip, flags);
+
+ con = __raw_readl(regcon);
+ con &= ~(0xf << con_4bit_shift(offset));
+ __raw_writel(con, regcon);
+
+ samsung_gpio_unlock(ourchip, flags);
+
+ return 0;
+}
+
+static int s5p64x0_gpiolib_rbank_output(struct gpio_chip *chip,
+ unsigned int offset, int value)
+{
+ struct samsung_gpio_chip *ourchip = to_samsung_gpio(chip);
+ void __iomem *base = ourchip->base;
+ void __iomem *regcon = base;
+ unsigned long con;
+ unsigned long dat;
+ unsigned long flags;
+ unsigned con_offset = offset;
+
+ switch (con_offset) {
+ case 6:
+ con_offset += 1;
+ case 0:
+ case 1:
+ case 2:
+ case 3:
+ case 4:
+ case 5:
+ regcon -= 4;
+ break;
+ default:
+ con_offset -= 7;
+ break;
+ }
+
+ samsung_gpio_lock(ourchip, flags);
+
+ con = __raw_readl(regcon);
+ con &= ~(0xf << con_4bit_shift(con_offset));
+ con |= 0x1 << con_4bit_shift(con_offset);
+
+ dat = __raw_readl(base + GPIODAT_OFF);
+ if (value)
+ dat |= 1 << offset;
+ else
+ dat &= ~(1 << offset);
+
+ __raw_writel(con, regcon);
+ __raw_writel(dat, base + GPIODAT_OFF);
+
+ samsung_gpio_unlock(ourchip, flags);
+
+ return 0;
+}
+
+static void samsung_gpiolib_set(struct gpio_chip *chip,
+ unsigned offset, int value)
+{
+ struct samsung_gpio_chip *ourchip = to_samsung_gpio(chip);
+ void __iomem *base = ourchip->base;
+ unsigned long flags;
+ unsigned long dat;
+
+ samsung_gpio_lock(ourchip, flags);
+
+ dat = __raw_readl(base + 0x04);
+ dat &= ~(1 << offset);
+ if (value)
+ dat |= 1 << offset;
+ __raw_writel(dat, base + 0x04);
+
+ samsung_gpio_unlock(ourchip, flags);
+}
+
+static int samsung_gpiolib_get(struct gpio_chip *chip, unsigned offset)
+{
+ struct samsung_gpio_chip *ourchip = to_samsung_gpio(chip);
+ unsigned long val;
+
+ val = __raw_readl(ourchip->base + 0x04);
+ val >>= offset;
+ val &= 1;
+
+ return val;
+}
+
+/*
+ * CONFIG_S3C_GPIO_TRACK enables the tracking of the s3c specific gpios
+ * for use with the configuration calls, and other parts of the s3c gpiolib
+ * support code.
+ *
+ * Not all s3c support code will need this, as some configurations of cpu
+ * may only support one or two different configuration options and have an
+ * easy gpio to samsung_gpio_chip mapping function. If this is the case, then
+ * the machine support file should provide its own samsung_gpiolib_getchip()
+ * and any other necessary functions.
+ */
+
+#ifdef CONFIG_S3C_GPIO_TRACK
+struct samsung_gpio_chip *s3c_gpios[S3C_GPIO_END];
+
+static __init void s3c_gpiolib_track(struct samsung_gpio_chip *chip)
+{
+ unsigned int gpn;
+ int i;
+
+ gpn = chip->chip.base;
+ for (i = 0; i < chip->chip.ngpio; i++, gpn++) {
+ BUG_ON(gpn >= ARRAY_SIZE(s3c_gpios));
+ s3c_gpios[gpn] = chip;
+ }
+}
+#endif /* CONFIG_S3C_GPIO_TRACK */
+
+/*
+ * samsung_gpiolib_add() - add the Samsung gpio_chip.
+ * @chip: The chip to register
+ *
+ * This is a wrapper to gpiochip_add() that takes our specific gpio chip
+ * information and makes the necessary alterations for the platform and
+ * notes the information for use with the configuration systems and any
+ * other parts of the system.
+ */
+
+static void __init samsung_gpiolib_add(struct samsung_gpio_chip *chip)
+{
+ struct gpio_chip *gc = &chip->chip;
+ int ret;
+
+ BUG_ON(!chip->base);
+ BUG_ON(!gc->label);
+ BUG_ON(!gc->ngpio);
+
+ spin_lock_init(&chip->lock);
+
+ if (!gc->direction_input)
+ gc->direction_input = samsung_gpiolib_2bit_input;
+ if (!gc->direction_output)
+ gc->direction_output = samsung_gpiolib_2bit_output;
+ if (!gc->set)
+ gc->set = samsung_gpiolib_set;
+ if (!gc->get)
+ gc->get = samsung_gpiolib_get;
+
+#ifdef CONFIG_PM
+ if (chip->pm != NULL) {
+ if (!chip->pm->save || !chip->pm->resume)
+ printk(KERN_ERR "gpio: %s has missing PM functions\n",
+ gc->label);
+ } else
+ printk(KERN_ERR "gpio: %s has no PM function\n", gc->label);
+#endif
+
+ /* gpiochip_add() prints own failure message on error. */
+ ret = gpiochip_add(gc);
+ if (ret >= 0)
+ s3c_gpiolib_track(chip);
+}
+
+static void __init s3c24xx_gpiolib_add_chips(struct samsung_gpio_chip *chip,
+ int nr_chips, void __iomem *base)
+{
+ int i;
+ struct gpio_chip *gc = &chip->chip;
+
+ for (i = 0 ; i < nr_chips; i++, chip++) {
+ if (!chip->config)
+ chip->config = &s3c24xx_gpiocfg_default;
+ if (!chip->pm)
+ chip->pm = __gpio_pm(&samsung_gpio_pm_2bit);
+ if ((base != NULL) && (chip->base == NULL))
+ chip->base = base + ((i) * 0x10);
+
+ if (!gc->direction_input)
+ gc->direction_input = samsung_gpiolib_2bit_input;
+ if (!gc->direction_output)
+ gc->direction_output = samsung_gpiolib_2bit_output;
+
+ samsung_gpiolib_add(chip);
+ }
+}
+
+static void __init samsung_gpiolib_add_2bit_chips(struct samsung_gpio_chip *chip,
+ int nr_chips, void __iomem *base,
+ unsigned int offset)
+{
+ int i;
+
+ for (i = 0 ; i < nr_chips; i++, chip++) {
+ chip->chip.direction_input = samsung_gpiolib_2bit_input;
+ chip->chip.direction_output = samsung_gpiolib_2bit_output;
+
+ if (!chip->config)
+ chip->config = &samsung_gpio_cfgs[7];
+ if (!chip->pm)
+ chip->pm = __gpio_pm(&samsung_gpio_pm_2bit);
+ if ((base != NULL) && (chip->base == NULL))
+ chip->base = base + ((i) * offset);
+
+ samsung_gpiolib_add(chip);
+ }
+}
+
+/*
+ * samsung_gpiolib_add_4bit_chips - 4bit single register GPIO config.
+ * @chip: The gpio chip that is being configured.
+ * @nr_chips: The no of chips (gpio ports) for the GPIO being configured.
+ *
+ * This helper deal with the GPIO cases where the control register has 4 bits
+ * of control per GPIO, generally in the form of:
+ * 0000 = Input
+ * 0001 = Output
+ * others = Special functions (dependent on bank)
+ *
+ * Note, since the code to deal with the case where there are two control
+ * registers instead of one, we do not have a separate set of function
+ * (samsung_gpiolib_add_4bit2_chips)for each case.
+ */
+
+static void __init samsung_gpiolib_add_4bit_chips(struct samsung_gpio_chip *chip,
+ int nr_chips, void __iomem *base)
+{
+ int i;
+
+ for (i = 0 ; i < nr_chips; i++, chip++) {
+ chip->chip.direction_input = samsung_gpiolib_4bit_input;
+ chip->chip.direction_output = samsung_gpiolib_4bit_output;
+
+ if (!chip->config)
+ chip->config = &samsung_gpio_cfgs[2];
+ if (!chip->pm)
+ chip->pm = __gpio_pm(&samsung_gpio_pm_4bit);
+ if ((base != NULL) && (chip->base == NULL))
+ chip->base = base + ((i) * 0x20);
+
+ samsung_gpiolib_add(chip);
+ }
+}
+
+static void __init samsung_gpiolib_add_4bit2_chips(struct samsung_gpio_chip *chip,
+ int nr_chips)
+{
+ for (; nr_chips > 0; nr_chips--, chip++) {
+ chip->chip.direction_input = samsung_gpiolib_4bit2_input;
+ chip->chip.direction_output = samsung_gpiolib_4bit2_output;
+
+ if (!chip->config)
+ chip->config = &samsung_gpio_cfgs[2];
+ if (!chip->pm)
+ chip->pm = __gpio_pm(&samsung_gpio_pm_4bit);
+
+ samsung_gpiolib_add(chip);
+ }
+}
+
+static void __init s5p64x0_gpiolib_add_rbank(struct samsung_gpio_chip *chip,
+ int nr_chips)
+{
+ for (; nr_chips > 0; nr_chips--, chip++) {
+ chip->chip.direction_input = s5p64x0_gpiolib_rbank_input;
+ chip->chip.direction_output = s5p64x0_gpiolib_rbank_output;
+
+ if (!chip->pm)
+ chip->pm = __gpio_pm(&samsung_gpio_pm_4bit);
+
+ samsung_gpiolib_add(chip);
+ }
+}
+
+int samsung_gpiolib_to_irq(struct gpio_chip *chip, unsigned int offset)
+{
+ struct samsung_gpio_chip *samsung_chip = container_of(chip, struct samsung_gpio_chip, chip);
+
+ return samsung_chip->irq_base + offset;
+}
+
+#ifdef CONFIG_PLAT_S3C24XX
+static int s3c24xx_gpiolib_fbank_to_irq(struct gpio_chip *chip, unsigned offset)
+{
+ if (offset < 4)
+ return IRQ_EINT0 + offset;
+
+ if (offset < 8)
+ return IRQ_EINT4 + offset - 4;
+
+ return -EINVAL;
+}
+#endif
+
+#ifdef CONFIG_PLAT_S3C64XX
+static int s3c64xx_gpiolib_mbank_to_irq(struct gpio_chip *chip, unsigned pin)
+{
+ return pin < 5 ? IRQ_EINT(23) + pin : -ENXIO;
+}
+
+static int s3c64xx_gpiolib_lbank_to_irq(struct gpio_chip *chip, unsigned pin)
+{
+ return pin >= 8 ? IRQ_EINT(16) + pin - 8 : -ENXIO;
+}
+#endif
+
+struct samsung_gpio_chip s3c24xx_gpios[] = {
+#ifdef CONFIG_PLAT_S3C24XX
+ {
+ .config = &s3c24xx_gpiocfg_banka,
+ .chip = {
+ .base = S3C2410_GPA(0),
+ .owner = THIS_MODULE,
+ .label = "GPIOA",
+ .ngpio = 24,
+ .direction_input = s3c24xx_gpiolib_banka_input,
+ .direction_output = s3c24xx_gpiolib_banka_output,
+ },
+ }, {
+ .chip = {
+ .base = S3C2410_GPB(0),
+ .owner = THIS_MODULE,
+ .label = "GPIOB",
+ .ngpio = 16,
+ },
+ }, {
+ .chip = {
+ .base = S3C2410_GPC(0),
+ .owner = THIS_MODULE,
+ .label = "GPIOC",
+ .ngpio = 16,
+ },
+ }, {
+ .chip = {
+ .base = S3C2410_GPD(0),
+ .owner = THIS_MODULE,
+ .label = "GPIOD",
+ .ngpio = 16,
+ },
+ }, {
+ .chip = {
+ .base = S3C2410_GPE(0),
+ .label = "GPIOE",
+ .owner = THIS_MODULE,
+ .ngpio = 16,
+ },
+ }, {
+ .chip = {
+ .base = S3C2410_GPF(0),
+ .owner = THIS_MODULE,
+ .label = "GPIOF",
+ .ngpio = 8,
+ .to_irq = s3c24xx_gpiolib_fbank_to_irq,
+ },
+ }, {
+ .irq_base = IRQ_EINT8,
+ .chip = {
+ .base = S3C2410_GPG(0),
+ .owner = THIS_MODULE,
+ .label = "GPIOG",
+ .ngpio = 16,
+ .to_irq = samsung_gpiolib_to_irq,
+ },
+ }, {
+ .chip = {
+ .base = S3C2410_GPH(0),
+ .owner = THIS_MODULE,
+ .label = "GPIOH",
+ .ngpio = 11,
+ },
+ },
+ /* GPIOS for the S3C2443 and later devices. */
+ {
+ .base = S3C2440_GPJCON,
+ .chip = {
+ .base = S3C2410_GPJ(0),
+ .owner = THIS_MODULE,
+ .label = "GPIOJ",
+ .ngpio = 16,
+ },
+ }, {
+ .base = S3C2443_GPKCON,
+ .chip = {
+ .base = S3C2410_GPK(0),
+ .owner = THIS_MODULE,
+ .label = "GPIOK",
+ .ngpio = 16,
+ },
+ }, {
+ .base = S3C2443_GPLCON,
+ .chip = {
+ .base = S3C2410_GPL(0),
+ .owner = THIS_MODULE,
+ .label = "GPIOL",
+ .ngpio = 15,
+ },
+ }, {
+ .base = S3C2443_GPMCON,
+ .chip = {
+ .base = S3C2410_GPM(0),
+ .owner = THIS_MODULE,
+ .label = "GPIOM",
+ .ngpio = 2,
+ },
+ },
+#endif
+};
+
+/*
+ * GPIO bank summary:
+ *
+ * Bank GPIOs Style SlpCon ExtInt Group
+ * A 8 4Bit Yes 1
+ * B 7 4Bit Yes 1
+ * C 8 4Bit Yes 2
+ * D 5 4Bit Yes 3
+ * E 5 4Bit Yes None
+ * F 16 2Bit Yes 4 [1]
+ * G 7 4Bit Yes 5
+ * H 10 4Bit[2] Yes 6
+ * I 16 2Bit Yes None
+ * J 12 2Bit Yes None
+ * K 16 4Bit[2] No None
+ * L 15 4Bit[2] No None
+ * M 6 4Bit No IRQ_EINT
+ * N 16 2Bit No IRQ_EINT
+ * O 16 2Bit Yes 7
+ * P 15 2Bit Yes 8
+ * Q 9 2Bit Yes 9
+ *
+ * [1] BANKF pins 14,15 do not form part of the external interrupt sources
+ * [2] BANK has two control registers, GPxCON0 and GPxCON1
+ */
+
+static struct samsung_gpio_chip s3c64xx_gpios_4bit[] = {
+#ifdef CONFIG_PLAT_S3C64XX
+ {
+ .chip = {
+ .base = S3C64XX_GPA(0),
+ .ngpio = S3C64XX_GPIO_A_NR,
+ .label = "GPA",
+ },
+ }, {
+ .chip = {
+ .base = S3C64XX_GPB(0),
+ .ngpio = S3C64XX_GPIO_B_NR,
+ .label = "GPB",
+ },
+ }, {
+ .chip = {
+ .base = S3C64XX_GPC(0),
+ .ngpio = S3C64XX_GPIO_C_NR,
+ .label = "GPC",
+ },
+ }, {
+ .chip = {
+ .base = S3C64XX_GPD(0),
+ .ngpio = S3C64XX_GPIO_D_NR,
+ .label = "GPD",
+ },
+ }, {
+ .config = &samsung_gpio_cfgs[0],
+ .chip = {
+ .base = S3C64XX_GPE(0),
+ .ngpio = S3C64XX_GPIO_E_NR,
+ .label = "GPE",
+ },
+ }, {
+ .base = S3C64XX_GPG_BASE,
+ .chip = {
+ .base = S3C64XX_GPG(0),
+ .ngpio = S3C64XX_GPIO_G_NR,
+ .label = "GPG",
+ },
+ }, {
+ .base = S3C64XX_GPM_BASE,
+ .config = &samsung_gpio_cfgs[1],
+ .chip = {
+ .base = S3C64XX_GPM(0),
+ .ngpio = S3C64XX_GPIO_M_NR,
+ .label = "GPM",
+ .to_irq = s3c64xx_gpiolib_mbank_to_irq,
+ },
+ },
+#endif
+};
+
+static struct samsung_gpio_chip s3c64xx_gpios_4bit2[] = {
+#ifdef CONFIG_PLAT_S3C64XX
+ {
+ .base = S3C64XX_GPH_BASE + 0x4,
+ .chip = {
+ .base = S3C64XX_GPH(0),
+ .ngpio = S3C64XX_GPIO_H_NR,
+ .label = "GPH",
+ },
+ }, {
+ .base = S3C64XX_GPK_BASE + 0x4,
+ .config = &samsung_gpio_cfgs[0],
+ .chip = {
+ .base = S3C64XX_GPK(0),
+ .ngpio = S3C64XX_GPIO_K_NR,
+ .label = "GPK",
+ },
+ }, {
+ .base = S3C64XX_GPL_BASE + 0x4,
+ .config = &samsung_gpio_cfgs[1],
+ .chip = {
+ .base = S3C64XX_GPL(0),
+ .ngpio = S3C64XX_GPIO_L_NR,
+ .label = "GPL",
+ .to_irq = s3c64xx_gpiolib_lbank_to_irq,
+ },
+ },
+#endif
+};
+
+static struct samsung_gpio_chip s3c64xx_gpios_2bit[] = {
+#ifdef CONFIG_PLAT_S3C64XX
+ {
+ .base = S3C64XX_GPF_BASE,
+ .config = &samsung_gpio_cfgs[6],
+ .chip = {
+ .base = S3C64XX_GPF(0),
+ .ngpio = S3C64XX_GPIO_F_NR,
+ .label = "GPF",
+ },
+ }, {
+ .config = &samsung_gpio_cfgs[7],
+ .chip = {
+ .base = S3C64XX_GPI(0),
+ .ngpio = S3C64XX_GPIO_I_NR,
+ .label = "GPI",
+ },
+ }, {
+ .config = &samsung_gpio_cfgs[7],
+ .chip = {
+ .base = S3C64XX_GPJ(0),
+ .ngpio = S3C64XX_GPIO_J_NR,
+ .label = "GPJ",
+ },
+ }, {
+ .config = &samsung_gpio_cfgs[6],
+ .chip = {
+ .base = S3C64XX_GPO(0),
+ .ngpio = S3C64XX_GPIO_O_NR,
+ .label = "GPO",
+ },
+ }, {
+ .config = &samsung_gpio_cfgs[6],
+ .chip = {
+ .base = S3C64XX_GPP(0),
+ .ngpio = S3C64XX_GPIO_P_NR,
+ .label = "GPP",
+ },
+ }, {
+ .config = &samsung_gpio_cfgs[6],
+ .chip = {
+ .base = S3C64XX_GPQ(0),
+ .ngpio = S3C64XX_GPIO_Q_NR,
+ .label = "GPQ",
+ },
+ }, {
+ .base = S3C64XX_GPN_BASE,
+ .irq_base = IRQ_EINT(0),
+ .config = &samsung_gpio_cfgs[5],
+ .chip = {
+ .base = S3C64XX_GPN(0),
+ .ngpio = S3C64XX_GPIO_N_NR,
+ .label = "GPN",
+ .to_irq = samsung_gpiolib_to_irq,
+ },
+ },
+#endif
+};
+
+/*
+ * S5P6440 GPIO bank summary:
+ *
+ * Bank GPIOs Style SlpCon ExtInt Group
+ * A 6 4Bit Yes 1
+ * B 7 4Bit Yes 1
+ * C 8 4Bit Yes 2
+ * F 2 2Bit Yes 4 [1]
+ * G 7 4Bit Yes 5
+ * H 10 4Bit[2] Yes 6
+ * I 16 2Bit Yes None
+ * J 12 2Bit Yes None
+ * N 16 2Bit No IRQ_EINT
+ * P 8 2Bit Yes 8
+ * R 15 4Bit[2] Yes 8
+ */
+
+static struct samsung_gpio_chip s5p6440_gpios_4bit[] = {
+#ifdef CONFIG_CPU_S5P6440
+ {
+ .chip = {
+ .base = S5P6440_GPA(0),
+ .ngpio = S5P6440_GPIO_A_NR,
+ .label = "GPA",
+ },
+ }, {
+ .chip = {
+ .base = S5P6440_GPB(0),
+ .ngpio = S5P6440_GPIO_B_NR,
+ .label = "GPB",
+ },
+ }, {
+ .chip = {
+ .base = S5P6440_GPC(0),
+ .ngpio = S5P6440_GPIO_C_NR,
+ .label = "GPC",
+ },
+ }, {
+ .base = S5P64X0_GPG_BASE,
+ .chip = {
+ .base = S5P6440_GPG(0),
+ .ngpio = S5P6440_GPIO_G_NR,
+ .label = "GPG",
+ },
+ },
+#endif
+};
+
+static struct samsung_gpio_chip s5p6440_gpios_4bit2[] = {
+#ifdef CONFIG_CPU_S5P6440
+ {
+ .base = S5P64X0_GPH_BASE + 0x4,
+ .chip = {
+ .base = S5P6440_GPH(0),
+ .ngpio = S5P6440_GPIO_H_NR,
+ .label = "GPH",
+ },
+ },
+#endif
+};
+
+static struct samsung_gpio_chip s5p6440_gpios_rbank[] = {
+#ifdef CONFIG_CPU_S5P6440
+ {
+ .base = S5P64X0_GPR_BASE + 0x4,
+ .config = &s5p64x0_gpio_cfg_rbank,
+ .chip = {
+ .base = S5P6440_GPR(0),
+ .ngpio = S5P6440_GPIO_R_NR,
+ .label = "GPR",
+ },
+ },
+#endif
+};
+
+static struct samsung_gpio_chip s5p6440_gpios_2bit[] = {
+#ifdef CONFIG_CPU_S5P6440
+ {
+ .base = S5P64X0_GPF_BASE,
+ .config = &samsung_gpio_cfgs[6],
+ .chip = {
+ .base = S5P6440_GPF(0),
+ .ngpio = S5P6440_GPIO_F_NR,
+ .label = "GPF",
+ },
+ }, {
+ .base = S5P64X0_GPI_BASE,
+ .config = &samsung_gpio_cfgs[4],
+ .chip = {
+ .base = S5P6440_GPI(0),
+ .ngpio = S5P6440_GPIO_I_NR,
+ .label = "GPI",
+ },
+ }, {
+ .base = S5P64X0_GPJ_BASE,
+ .config = &samsung_gpio_cfgs[4],
+ .chip = {
+ .base = S5P6440_GPJ(0),
+ .ngpio = S5P6440_GPIO_J_NR,
+ .label = "GPJ",
+ },
+ }, {
+ .base = S5P64X0_GPN_BASE,
+ .config = &samsung_gpio_cfgs[5],
+ .chip = {
+ .base = S5P6440_GPN(0),
+ .ngpio = S5P6440_GPIO_N_NR,
+ .label = "GPN",
+ },
+ }, {
+ .base = S5P64X0_GPP_BASE,
+ .config = &samsung_gpio_cfgs[6],
+ .chip = {
+ .base = S5P6440_GPP(0),
+ .ngpio = S5P6440_GPIO_P_NR,
+ .label = "GPP",
+ },
+ },
+#endif
+};
+
+/*
+ * S5P6450 GPIO bank summary:
+ *
+ * Bank GPIOs Style SlpCon ExtInt Group
+ * A 6 4Bit Yes 1
+ * B 7 4Bit Yes 1
+ * C 8 4Bit Yes 2
+ * D 8 4Bit Yes None
+ * F 2 2Bit Yes None
+ * G 14 4Bit[2] Yes 5
+ * H 10 4Bit[2] Yes 6
+ * I 16 2Bit Yes None
+ * J 12 2Bit Yes None
+ * K 5 4Bit Yes None
+ * N 16 2Bit No IRQ_EINT
+ * P 11 2Bit Yes 8
+ * Q 14 2Bit Yes None
+ * R 15 4Bit[2] Yes None
+ * S 8 2Bit Yes None
+ *
+ * [1] BANKF pins 14,15 do not form part of the external interrupt sources
+ * [2] BANK has two control registers, GPxCON0 and GPxCON1
+ */
+
+static struct samsung_gpio_chip s5p6450_gpios_4bit[] = {
+#ifdef CONFIG_CPU_S5P6450
+ {
+ .chip = {
+ .base = S5P6450_GPA(0),
+ .ngpio = S5P6450_GPIO_A_NR,
+ .label = "GPA",
+ },
+ }, {
+ .chip = {
+ .base = S5P6450_GPB(0),
+ .ngpio = S5P6450_GPIO_B_NR,
+ .label = "GPB",
+ },
+ }, {
+ .chip = {
+ .base = S5P6450_GPC(0),
+ .ngpio = S5P6450_GPIO_C_NR,
+ .label = "GPC",
+ },
+ }, {
+ .chip = {
+ .base = S5P6450_GPD(0),
+ .ngpio = S5P6450_GPIO_D_NR,
+ .label = "GPD",
+ },
+ }, {
+ .base = S5P6450_GPK_BASE,
+ .chip = {
+ .base = S5P6450_GPK(0),
+ .ngpio = S5P6450_GPIO_K_NR,
+ .label = "GPK",
+ },
+ },
+#endif
+};
+
+static struct samsung_gpio_chip s5p6450_gpios_4bit2[] = {
+#ifdef CONFIG_CPU_S5P6450
+ {
+ .base = S5P64X0_GPG_BASE + 0x4,
+ .chip = {
+ .base = S5P6450_GPG(0),
+ .ngpio = S5P6450_GPIO_G_NR,
+ .label = "GPG",
+ },
+ }, {
+ .base = S5P64X0_GPH_BASE + 0x4,
+ .chip = {
+ .base = S5P6450_GPH(0),
+ .ngpio = S5P6450_GPIO_H_NR,
+ .label = "GPH",
+ },
+ },
+#endif
+};
+
+static struct samsung_gpio_chip s5p6450_gpios_rbank[] = {
+#ifdef CONFIG_CPU_S5P6450
+ {
+ .base = S5P64X0_GPR_BASE + 0x4,
+ .config = &s5p64x0_gpio_cfg_rbank,
+ .chip = {
+ .base = S5P6450_GPR(0),
+ .ngpio = S5P6450_GPIO_R_NR,
+ .label = "GPR",
+ },
+ },
+#endif
+};
+
+static struct samsung_gpio_chip s5p6450_gpios_2bit[] = {
+#ifdef CONFIG_CPU_S5P6450
+ {
+ .base = S5P64X0_GPF_BASE,
+ .config = &samsung_gpio_cfgs[6],
+ .chip = {
+ .base = S5P6450_GPF(0),
+ .ngpio = S5P6450_GPIO_F_NR,
+ .label = "GPF",
+ },
+ }, {
+ .base = S5P64X0_GPI_BASE,
+ .config = &samsung_gpio_cfgs[4],
+ .chip = {
+ .base = S5P6450_GPI(0),
+ .ngpio = S5P6450_GPIO_I_NR,
+ .label = "GPI",
+ },
+ }, {
+ .base = S5P64X0_GPJ_BASE,
+ .config = &samsung_gpio_cfgs[4],
+ .chip = {
+ .base = S5P6450_GPJ(0),
+ .ngpio = S5P6450_GPIO_J_NR,
+ .label = "GPJ",
+ },
+ }, {
+ .base = S5P64X0_GPN_BASE,
+ .config = &samsung_gpio_cfgs[5],
+ .chip = {
+ .base = S5P6450_GPN(0),
+ .ngpio = S5P6450_GPIO_N_NR,
+ .label = "GPN",
+ },
+ }, {
+ .base = S5P64X0_GPP_BASE,
+ .config = &samsung_gpio_cfgs[6],
+ .chip = {
+ .base = S5P6450_GPP(0),
+ .ngpio = S5P6450_GPIO_P_NR,
+ .label = "GPP",
+ },
+ }, {
+ .base = S5P6450_GPQ_BASE,
+ .config = &samsung_gpio_cfgs[5],
+ .chip = {
+ .base = S5P6450_GPQ(0),
+ .ngpio = S5P6450_GPIO_Q_NR,
+ .label = "GPQ",
+ },
+ }, {
+ .base = S5P6450_GPS_BASE,
+ .config = &samsung_gpio_cfgs[6],
+ .chip = {
+ .base = S5P6450_GPS(0),
+ .ngpio = S5P6450_GPIO_S_NR,
+ .label = "GPS",
+ },
+ },
+#endif
+};
+
+/*
+ * S5PC100 GPIO bank summary:
+ *
+ * Bank GPIOs Style INT Type
+ * A0 8 4Bit GPIO_INT0
+ * A1 5 4Bit GPIO_INT1
+ * B 8 4Bit GPIO_INT2
+ * C 5 4Bit GPIO_INT3
+ * D 7 4Bit GPIO_INT4
+ * E0 8 4Bit GPIO_INT5
+ * E1 6 4Bit GPIO_INT6
+ * F0 8 4Bit GPIO_INT7
+ * F1 8 4Bit GPIO_INT8
+ * F2 8 4Bit GPIO_INT9
+ * F3 4 4Bit GPIO_INT10
+ * G0 8 4Bit GPIO_INT11
+ * G1 3 4Bit GPIO_INT12
+ * G2 7 4Bit GPIO_INT13
+ * G3 7 4Bit GPIO_INT14
+ * H0 8 4Bit WKUP_INT
+ * H1 8 4Bit WKUP_INT
+ * H2 8 4Bit WKUP_INT
+ * H3 8 4Bit WKUP_INT
+ * I 8 4Bit GPIO_INT15
+ * J0 8 4Bit GPIO_INT16
+ * J1 5 4Bit GPIO_INT17
+ * J2 8 4Bit GPIO_INT18
+ * J3 8 4Bit GPIO_INT19
+ * J4 4 4Bit GPIO_INT20
+ * K0 8 4Bit None
+ * K1 6 4Bit None
+ * K2 8 4Bit None
+ * K3 8 4Bit None
+ * L0 8 4Bit None
+ * L1 8 4Bit None
+ * L2 8 4Bit None
+ * L3 8 4Bit None
+ */
+
+static struct samsung_gpio_chip s5pc100_gpios_4bit[] = {
+#ifdef CONFIG_CPU_S5PC100
+ {
+ .chip = {
+ .base = S5PC100_GPA0(0),
+ .ngpio = S5PC100_GPIO_A0_NR,
+ .label = "GPA0",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPA1(0),
+ .ngpio = S5PC100_GPIO_A1_NR,
+ .label = "GPA1",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPB(0),
+ .ngpio = S5PC100_GPIO_B_NR,
+ .label = "GPB",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPC(0),
+ .ngpio = S5PC100_GPIO_C_NR,
+ .label = "GPC",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPD(0),
+ .ngpio = S5PC100_GPIO_D_NR,
+ .label = "GPD",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPE0(0),
+ .ngpio = S5PC100_GPIO_E0_NR,
+ .label = "GPE0",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPE1(0),
+ .ngpio = S5PC100_GPIO_E1_NR,
+ .label = "GPE1",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPF0(0),
+ .ngpio = S5PC100_GPIO_F0_NR,
+ .label = "GPF0",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPF1(0),
+ .ngpio = S5PC100_GPIO_F1_NR,
+ .label = "GPF1",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPF2(0),
+ .ngpio = S5PC100_GPIO_F2_NR,
+ .label = "GPF2",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPF3(0),
+ .ngpio = S5PC100_GPIO_F3_NR,
+ .label = "GPF3",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPG0(0),
+ .ngpio = S5PC100_GPIO_G0_NR,
+ .label = "GPG0",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPG1(0),
+ .ngpio = S5PC100_GPIO_G1_NR,
+ .label = "GPG1",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPG2(0),
+ .ngpio = S5PC100_GPIO_G2_NR,
+ .label = "GPG2",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPG3(0),
+ .ngpio = S5PC100_GPIO_G3_NR,
+ .label = "GPG3",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPI(0),
+ .ngpio = S5PC100_GPIO_I_NR,
+ .label = "GPI",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPJ0(0),
+ .ngpio = S5PC100_GPIO_J0_NR,
+ .label = "GPJ0",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPJ1(0),
+ .ngpio = S5PC100_GPIO_J1_NR,
+ .label = "GPJ1",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPJ2(0),
+ .ngpio = S5PC100_GPIO_J2_NR,
+ .label = "GPJ2",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPJ3(0),
+ .ngpio = S5PC100_GPIO_J3_NR,
+ .label = "GPJ3",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPJ4(0),
+ .ngpio = S5PC100_GPIO_J4_NR,
+ .label = "GPJ4",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPK0(0),
+ .ngpio = S5PC100_GPIO_K0_NR,
+ .label = "GPK0",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPK1(0),
+ .ngpio = S5PC100_GPIO_K1_NR,
+ .label = "GPK1",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPK2(0),
+ .ngpio = S5PC100_GPIO_K2_NR,
+ .label = "GPK2",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPK3(0),
+ .ngpio = S5PC100_GPIO_K3_NR,
+ .label = "GPK3",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPL0(0),
+ .ngpio = S5PC100_GPIO_L0_NR,
+ .label = "GPL0",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPL1(0),
+ .ngpio = S5PC100_GPIO_L1_NR,
+ .label = "GPL1",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPL2(0),
+ .ngpio = S5PC100_GPIO_L2_NR,
+ .label = "GPL2",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPL3(0),
+ .ngpio = S5PC100_GPIO_L3_NR,
+ .label = "GPL3",
+ },
+ }, {
+ .chip = {
+ .base = S5PC100_GPL4(0),
+ .ngpio = S5PC100_GPIO_L4_NR,
+ .label = "GPL4",
+ },
+ }, {
+ .base = (S5P_VA_GPIO + 0xC00),
+ .irq_base = IRQ_EINT(0),
+ .chip = {
+ .base = S5PC100_GPH0(0),
+ .ngpio = S5PC100_GPIO_H0_NR,
+ .label = "GPH0",
+ .to_irq = samsung_gpiolib_to_irq,
+ },
+ }, {
+ .base = (S5P_VA_GPIO + 0xC20),
+ .irq_base = IRQ_EINT(8),
+ .chip = {
+ .base = S5PC100_GPH1(0),
+ .ngpio = S5PC100_GPIO_H1_NR,
+ .label = "GPH1",
+ .to_irq = samsung_gpiolib_to_irq,
+ },
+ }, {
+ .base = (S5P_VA_GPIO + 0xC40),
+ .irq_base = IRQ_EINT(16),
+ .chip = {
+ .base = S5PC100_GPH2(0),
+ .ngpio = S5PC100_GPIO_H2_NR,
+ .label = "GPH2",
+ .to_irq = samsung_gpiolib_to_irq,
+ },
+ }, {
+ .base = (S5P_VA_GPIO + 0xC60),
+ .irq_base = IRQ_EINT(24),
+ .chip = {
+ .base = S5PC100_GPH3(0),
+ .ngpio = S5PC100_GPIO_H3_NR,
+ .label = "GPH3",
+ .to_irq = samsung_gpiolib_to_irq,
+ },
+ },
+#endif
+};
+
+/*
+ * Followings are the gpio banks in S5PV210/S5PC110
+ *
+ * The 'config' member when left to NULL, is initialized to the default
+ * structure samsung_gpio_cfgs[4] in the init function below.
+ *
+ * The 'base' member is also initialized in the init function below.
+ * Note: The initialization of 'base' member of samsung_gpio_chip structure
+ * uses the above macro and depends on the banks being listed in order here.
+ */
+
+static struct samsung_gpio_chip s5pv210_gpios_4bit[] = {
+#ifdef CONFIG_CPU_S5PV210
+ {
+ .chip = {
+ .base = S5PV210_GPA0(0),
+ .ngpio = S5PV210_GPIO_A0_NR,
+ .label = "GPA0",
+ },
+ }, {
+ .chip = {
+ .base = S5PV210_GPA1(0),
+ .ngpio = S5PV210_GPIO_A1_NR,
+ .label = "GPA1",
+ },
+ }, {
+ .chip = {
+ .base = S5PV210_GPB(0),
+ .ngpio = S5PV210_GPIO_B_NR,
+ .label = "GPB",
+ },
+ }, {
+ .chip = {
+ .base = S5PV210_GPC0(0),
+ .ngpio = S5PV210_GPIO_C0_NR,
+ .label = "GPC0",
+ },
+ }, {
+ .chip = {
+ .base = S5PV210_GPC1(0),
+ .ngpio = S5PV210_GPIO_C1_NR,
+ .label = "GPC1",
+ },
+ }, {
+ .chip = {
+ .base = S5PV210_GPD0(0),
+ .ngpio = S5PV210_GPIO_D0_NR,
+ .label = "GPD0",
+ },
+ }, {
+ .chip = {
+ .base = S5PV210_GPD1(0),
+ .ngpio = S5PV210_GPIO_D1_NR,
+ .label = "GPD1",
+ },
+ }, {
+ .chip = {
+ .base = S5PV210_GPE0(0),
+ .ngpio = S5PV210_GPIO_E0_NR,
+ .label = "GPE0",
+ },
+ }, {
+ .chip = {
+ .base = S5PV210_GPE1(0),
+ .ngpio = S5PV210_GPIO_E1_NR,
+ .label = "GPE1",
+ },
+ }, {
+ .chip = {
+ .base = S5PV210_GPF0(0),
+ .ngpio = S5PV210_GPIO_F0_NR,
+ .label = "GPF0",
+ },
+ }, {
+ .chip = {
+ .base = S5PV210_GPF1(0),
+ .ngpio = S5PV210_GPIO_F1_NR,
+ .label = "GPF1",
+ },
+ }, {
+ .chip = {
+ .base = S5PV210_GPF2(0),
+ .ngpio = S5PV210_GPIO_F2_NR,
+ .label = "GPF2",
+ },
+ }, {
+ .chip = {
+ .base = S5PV210_GPF3(0),
+ .ngpio = S5PV210_GPIO_F3_NR,
+ .label = "GPF3",
+ },
+ }, {
+ .chip = {
+ .base = S5PV210_GPG0(0),
+ .ngpio = S5PV210_GPIO_G0_NR,
+ .label = "GPG0",
+ },
+ }, {
+ .chip = {
+ .base = S5PV210_GPG1(0),
+ .ngpio = S5PV210_GPIO_G1_NR,
+ .label = "GPG1",
+ },
+ }, {
+ .chip = {
+ .base = S5PV210_GPG2(0),
+ .ngpio = S5PV210_GPIO_G2_NR,
+ .label = "GPG2",
+ },
+ }, {
+ .chip = {
+ .base = S5PV210_GPG3(0),
+ .ngpio = S5PV210_GPIO_G3_NR,
+ .label = "GPG3",
+ },
+ }, {
+ .chip = {
+ .base = S5PV210_GPI(0),
+ .ngpio = S5PV210_GPIO_I_NR,
+ .label = "GPI",
+ },
+ }, {
+ .chip = {
+ .base = S5PV210_GPJ0(0),
+ .ngpio = S5PV210_GPIO_J0_NR,
+ .label = "GPJ0",
+ },
+ }, {
+ .chip = {
+ .base = S5PV210_GPJ1(0),
+ .ngpio = S5PV210_GPIO_J1_NR,
+ .label = "GPJ1",
+ },
+ }, {
+ .chip = {
+ .base = S5PV210_GPJ2(0),
+ .ngpio = S5PV210_GPIO_J2_NR,
+ .label = "GPJ2",
+ },
+ }, {
+ .chip = {
+ .base = S5PV210_GPJ3(0),
+ .ngpio = S5PV210_GPIO_J3_NR,
+ .label = "GPJ3",
+ },
+ }, {
+ .chip = {
+ .base = S5PV210_GPJ4(0),
+ .ngpio = S5PV210_GPIO_J4_NR,
+ .label = "GPJ4",
+ },
+ }, {
+ .chip = {
+ .base = S5PV210_MP01(0),
+ .ngpio = S5PV210_GPIO_MP01_NR,
+ .label = "MP01",
+ },
+ }, {
+ .chip = {
+ .base = S5PV210_MP02(0),
+ .ngpio = S5PV210_GPIO_MP02_NR,
+ .label = "MP02",
+ },
+ }, {
+ .chip = {
+ .base = S5PV210_MP03(0),
+ .ngpio = S5PV210_GPIO_MP03_NR,
+ .label = "MP03",
+ },
+ }, {
+ .chip = {
+ .base = S5PV210_MP04(0),
+ .ngpio = S5PV210_GPIO_MP04_NR,
+ .label = "MP04",
+ },
+ }, {
+ .chip = {
+ .base = S5PV210_MP05(0),
+ .ngpio = S5PV210_GPIO_MP05_NR,
+ .label = "MP05",
+ },
+ }, {
+ .base = (S5P_VA_GPIO + 0xC00),
+ .irq_base = IRQ_EINT(0),
+ .chip = {
+ .base = S5PV210_GPH0(0),
+ .ngpio = S5PV210_GPIO_H0_NR,
+ .label = "GPH0",
+ .to_irq = samsung_gpiolib_to_irq,
+ },
+ }, {
+ .base = (S5P_VA_GPIO + 0xC20),
+ .irq_base = IRQ_EINT(8),
+ .chip = {
+ .base = S5PV210_GPH1(0),
+ .ngpio = S5PV210_GPIO_H1_NR,
+ .label = "GPH1",
+ .to_irq = samsung_gpiolib_to_irq,
+ },
+ }, {
+ .base = (S5P_VA_GPIO + 0xC40),
+ .irq_base = IRQ_EINT(16),
+ .chip = {
+ .base = S5PV210_GPH2(0),
+ .ngpio = S5PV210_GPIO_H2_NR,
+ .label = "GPH2",
+ .to_irq = samsung_gpiolib_to_irq,
+ },
+ }, {
+ .base = (S5P_VA_GPIO + 0xC60),
+ .irq_base = IRQ_EINT(24),
+ .chip = {
+ .base = S5PV210_GPH3(0),
+ .ngpio = S5PV210_GPIO_H3_NR,
+ .label = "GPH3",
+ .to_irq = samsung_gpiolib_to_irq,
+ },
+ },
+#endif
+};
+
+/*
+ * Followings are the gpio banks in EXYNOS4210
+ *
+ * The 'config' member when left to NULL, is initialized to the default
+ * structure samsung_gpio_cfgs[4] in the init function below.
+ *
+ * The 'base' member is also initialized in the init function below.
+ * Note: The initialization of 'base' member of samsung_gpio_chip structure
+ * uses the above macro and depends on the banks being listed in order here.
+ */
+
+static struct samsung_gpio_chip exynos4_gpios_1[] = {
+#ifdef CONFIG_ARCH_EXYNOS4
+ {
+ .chip = {
+ .base = EXYNOS4_GPA0(0),
+ .ngpio = EXYNOS4_GPIO_A0_NR,
+ .label = "GPA0",
+ },
+ }, {
+ .chip = {
+ .base = EXYNOS4_GPA1(0),
+ .ngpio = EXYNOS4_GPIO_A1_NR,
+ .label = "GPA1",
+ },
+ }, {
+ .chip = {
+ .base = EXYNOS4_GPB(0),
+ .ngpio = EXYNOS4_GPIO_B_NR,
+ .label = "GPB",
+ },
+ }, {
+ .chip = {
+ .base = EXYNOS4_GPC0(0),
+ .ngpio = EXYNOS4_GPIO_C0_NR,
+ .label = "GPC0",
+ },
+ }, {
+ .chip = {
+ .base = EXYNOS4_GPC1(0),
+ .ngpio = EXYNOS4_GPIO_C1_NR,
+ .label = "GPC1",
+ },
+ }, {
+ .chip = {
+ .base = EXYNOS4_GPD0(0),
+ .ngpio = EXYNOS4_GPIO_D0_NR,
+ .label = "GPD0",
+ },
+ }, {
+ .chip = {
+ .base = EXYNOS4_GPD1(0),
+ .ngpio = EXYNOS4_GPIO_D1_NR,
+ .label = "GPD1",
+ },
+ }, {
+ .chip = {
+ .base = EXYNOS4_GPE0(0),
+ .ngpio = EXYNOS4_GPIO_E0_NR,
+ .label = "GPE0",
+ },
+ }, {
+ .chip = {
+ .base = EXYNOS4_GPE1(0),
+ .ngpio = EXYNOS4_GPIO_E1_NR,
+ .label = "GPE1",
+ },
+ }, {
+ .chip = {
+ .base = EXYNOS4_GPE2(0),
+ .ngpio = EXYNOS4_GPIO_E2_NR,
+ .label = "GPE2",
+ },
+ }, {
+ .chip = {
+ .base = EXYNOS4_GPE3(0),
+ .ngpio = EXYNOS4_GPIO_E3_NR,
+ .label = "GPE3",
+ },
+ }, {
+ .chip = {
+ .base = EXYNOS4_GPE4(0),
+ .ngpio = EXYNOS4_GPIO_E4_NR,
+ .label = "GPE4",
+ },
+ }, {
+ .chip = {
+ .base = EXYNOS4_GPF0(0),
+ .ngpio = EXYNOS4_GPIO_F0_NR,
+ .label = "GPF0",
+ },
+ }, {
+ .chip = {
+ .base = EXYNOS4_GPF1(0),
+ .ngpio = EXYNOS4_GPIO_F1_NR,
+ .label = "GPF1",
+ },
+ }, {
+ .chip = {
+ .base = EXYNOS4_GPF2(0),
+ .ngpio = EXYNOS4_GPIO_F2_NR,
+ .label = "GPF2",
+ },
+ }, {
+ .chip = {
+ .base = EXYNOS4_GPF3(0),
+ .ngpio = EXYNOS4_GPIO_F3_NR,
+ .label = "GPF3",
+ },
+ },
+#endif
+};
+
+static struct samsung_gpio_chip exynos4_gpios_2[] = {
+#ifdef CONFIG_ARCH_EXYNOS4
+ {
+ .chip = {
+ .base = EXYNOS4_GPJ0(0),
+ .ngpio = EXYNOS4_GPIO_J0_NR,
+ .label = "GPJ0",
+ },
+ }, {
+ .chip = {
+ .base = EXYNOS4_GPJ1(0),
+ .ngpio = EXYNOS4_GPIO_J1_NR,
+ .label = "GPJ1",
+ },
+ }, {
+ .chip = {
+ .base = EXYNOS4_GPK0(0),
+ .ngpio = EXYNOS4_GPIO_K0_NR,
+ .label = "GPK0",
+ },
+ }, {
+ .chip = {
+ .base = EXYNOS4_GPK1(0),
+ .ngpio = EXYNOS4_GPIO_K1_NR,
+ .label = "GPK1",
+ },
+ }, {
+ .chip = {
+ .base = EXYNOS4_GPK2(0),
+ .ngpio = EXYNOS4_GPIO_K2_NR,
+ .label = "GPK2",
+ },
+ }, {
+ .chip = {
+ .base = EXYNOS4_GPK3(0),
+ .ngpio = EXYNOS4_GPIO_K3_NR,
+ .label = "GPK3",
+ },
+ }, {
+ .chip = {
+ .base = EXYNOS4_GPL0(0),
+ .ngpio = EXYNOS4_GPIO_L0_NR,
+ .label = "GPL0",
+ },
+ }, {
+ .chip = {
+ .base = EXYNOS4_GPL1(0),
+ .ngpio = EXYNOS4_GPIO_L1_NR,
+ .label = "GPL1",
+ },
+ }, {
+ .chip = {
+ .base = EXYNOS4_GPL2(0),
+ .ngpio = EXYNOS4_GPIO_L2_NR,
+ .label = "GPL2",
+ },
+ }, {
+ .config = &samsung_gpio_cfgs[4],
+ .chip = {
+ .base = EXYNOS4_GPY0(0),
+ .ngpio = EXYNOS4_GPIO_Y0_NR,
+ .label = "GPY0",
+ },
+ }, {
+ .config = &samsung_gpio_cfgs[4],
+ .chip = {
+ .base = EXYNOS4_GPY1(0),
+ .ngpio = EXYNOS4_GPIO_Y1_NR,
+ .label = "GPY1",
+ },
+ }, {
+ .config = &samsung_gpio_cfgs[4],
+ .chip = {
+ .base = EXYNOS4_GPY2(0),
+ .ngpio = EXYNOS4_GPIO_Y2_NR,
+ .label = "GPY2",
+ },
+ }, {
+ .config = &samsung_gpio_cfgs[4],
+ .chip = {
+ .base = EXYNOS4_GPY3(0),
+ .ngpio = EXYNOS4_GPIO_Y3_NR,
+ .label = "GPY3",
+ },
+ }, {
+ .config = &samsung_gpio_cfgs[4],
+ .chip = {
+ .base = EXYNOS4_GPY4(0),
+ .ngpio = EXYNOS4_GPIO_Y4_NR,
+ .label = "GPY4",
+ },
+ }, {
+ .config = &samsung_gpio_cfgs[4],
+ .chip = {
+ .base = EXYNOS4_GPY5(0),
+ .ngpio = EXYNOS4_GPIO_Y5_NR,
+ .label = "GPY5",
+ },
+ }, {
+ .config = &samsung_gpio_cfgs[4],
+ .chip = {
+ .base = EXYNOS4_GPY6(0),
+ .ngpio = EXYNOS4_GPIO_Y6_NR,
+ .label = "GPY6",
+ },
+ }, {
+ .base = (S5P_VA_GPIO2 + 0xC00),
+ .config = &samsung_gpio_cfgs[4],
+ .irq_base = IRQ_EINT(0),
+ .chip = {
+ .base = EXYNOS4_GPX0(0),
+ .ngpio = EXYNOS4_GPIO_X0_NR,
+ .label = "GPX0",
+ .to_irq = samsung_gpiolib_to_irq,
+ },
+ }, {
+ .base = (S5P_VA_GPIO2 + 0xC20),
+ .config = &samsung_gpio_cfgs[4],
+ .irq_base = IRQ_EINT(8),
+ .chip = {
+ .base = EXYNOS4_GPX1(0),
+ .ngpio = EXYNOS4_GPIO_X1_NR,
+ .label = "GPX1",
+ .to_irq = samsung_gpiolib_to_irq,
+ },
+ }, {
+ .base = (S5P_VA_GPIO2 + 0xC40),
+ .config = &samsung_gpio_cfgs[4],
+ .irq_base = IRQ_EINT(16),
+ .chip = {
+ .base = EXYNOS4_GPX2(0),
+ .ngpio = EXYNOS4_GPIO_X2_NR,
+ .label = "GPX2",
+ .to_irq = samsung_gpiolib_to_irq,
+ },
+ }, {
+ .base = (S5P_VA_GPIO2 + 0xC60),
+ .config = &samsung_gpio_cfgs[4],
+ .irq_base = IRQ_EINT(24),
+ .chip = {
+ .base = EXYNOS4_GPX3(0),
+ .ngpio = EXYNOS4_GPIO_X3_NR,
+ .label = "GPX3",
+ .to_irq = samsung_gpiolib_to_irq,
+ },
+ },
+#endif
+};
+
+static struct samsung_gpio_chip exynos4_gpios_3[] = {
+#ifdef CONFIG_ARCH_EXYNOS4
+ {
+ .chip = {
+ .base = EXYNOS4_GPZ(0),
+ .ngpio = EXYNOS4_GPIO_Z_NR,
+ .label = "GPZ",
+ },
+ },
+#endif
+};
+
+/* TODO: cleanup soc_is_* */
+static __init int samsung_gpiolib_init(void)
+{
+ struct samsung_gpio_chip *chip;
+ int i, nr_chips;
+ int group = 0;
+
+ samsung_gpiolib_set_cfg(samsung_gpio_cfgs, ARRAY_SIZE(samsung_gpio_cfgs));
+
+ if (soc_is_s3c24xx()) {
+ s3c24xx_gpiolib_add_chips(s3c24xx_gpios,
+ ARRAY_SIZE(s3c24xx_gpios), S3C24XX_VA_GPIO);
+ } else if (soc_is_s3c64xx()) {
+ samsung_gpiolib_add_2bit_chips(s3c64xx_gpios_2bit,
+ ARRAY_SIZE(s3c64xx_gpios_2bit),
+ S3C64XX_VA_GPIO + 0xE0, 0x20);
+ samsung_gpiolib_add_4bit_chips(s3c64xx_gpios_4bit,
+ ARRAY_SIZE(s3c64xx_gpios_4bit),
+ S3C64XX_VA_GPIO);
+ samsung_gpiolib_add_4bit2_chips(s3c64xx_gpios_4bit2,
+ ARRAY_SIZE(s3c64xx_gpios_4bit2));
+ } else if (soc_is_s5p6440()) {
+ samsung_gpiolib_add_2bit_chips(s5p6440_gpios_2bit,
+ ARRAY_SIZE(s5p6440_gpios_2bit), NULL, 0x0);
+ samsung_gpiolib_add_4bit_chips(s5p6440_gpios_4bit,
+ ARRAY_SIZE(s5p6440_gpios_4bit), S5P_VA_GPIO);
+ samsung_gpiolib_add_4bit2_chips(s5p6440_gpios_4bit2,
+ ARRAY_SIZE(s5p6440_gpios_4bit2));
+ s5p64x0_gpiolib_add_rbank(s5p6440_gpios_rbank,
+ ARRAY_SIZE(s5p6440_gpios_rbank));
+ } else if (soc_is_s5p6450()) {
+ samsung_gpiolib_add_2bit_chips(s5p6450_gpios_2bit,
+ ARRAY_SIZE(s5p6450_gpios_2bit), NULL, 0x0);
+ samsung_gpiolib_add_4bit_chips(s5p6450_gpios_4bit,
+ ARRAY_SIZE(s5p6450_gpios_4bit), S5P_VA_GPIO);
+ samsung_gpiolib_add_4bit2_chips(s5p6450_gpios_4bit2,
+ ARRAY_SIZE(s5p6450_gpios_4bit2));
+ s5p64x0_gpiolib_add_rbank(s5p6450_gpios_rbank,
+ ARRAY_SIZE(s5p6450_gpios_rbank));
+ } else if (soc_is_s5pc100()) {
+ group = 0;
+ chip = s5pc100_gpios_4bit;
+ nr_chips = ARRAY_SIZE(s5pc100_gpios_4bit);
+
+ for (i = 0; i < nr_chips; i++, chip++) {
+ if (!chip->config) {
+ chip->config = &samsung_gpio_cfgs[4];
+ chip->group = group++;
+ }
+ }
+ samsung_gpiolib_add_4bit_chips(chip, nr_chips, S5P_VA_GPIO);
+#if defined(CONFIG_CPU_S5PC100) && defined(CONFIG_S5P_GPIO_INT)
+ s5p_register_gpioint_bank(IRQ_GPIOINT, 0, S5P_GPIOINT_GROUP_MAXNR);
+#endif
+ } else if (soc_is_s5pv210()) {
+ group = 0;
+ chip = s5pv210_gpios_4bit;
+ nr_chips = ARRAY_SIZE(s5pv210_gpios_4bit);
+
+ for (i = 0; i < nr_chips; i++, chip++) {
+ if (!chip->config) {
+ chip->config = &samsung_gpio_cfgs[4];
+ chip->group = group++;
+ }
+ }
+ samsung_gpiolib_add_4bit_chips(chip, nr_chips, S5P_VA_GPIO);
+#if defined(CONFIG_CPU_S5PV210) && defined(CONFIG_S5P_GPIO_INT)
+ s5p_register_gpioint_bank(IRQ_GPIOINT, 0, S5P_GPIOINT_GROUP_MAXNR);
+#endif
+ } else if (soc_is_exynos4210()) {
+ group = 0;
+
+ /* gpio part1 */
+ chip = exynos4_gpios_1;
+ nr_chips = ARRAY_SIZE(exynos4_gpios_1);
+
+ for (i = 0; i < nr_chips; i++, chip++) {
+ if (!chip->config) {
+ chip->config = &exynos4_gpio_cfg;
+ chip->group = group++;
+ }
+ }
+ samsung_gpiolib_add_4bit_chips(chip, nr_chips, S5P_VA_GPIO1);
+
+ /* gpio part2 */
+ chip = exynos4_gpios_2;
+ nr_chips = ARRAY_SIZE(exynos4_gpios_2);
+
+ for (i = 0; i < nr_chips; i++, chip++) {
+ if (!chip->config) {
+ chip->config = &exynos4_gpio_cfg;
+ chip->group = group++;
+ }
+ }
+ samsung_gpiolib_add_4bit_chips(chip, nr_chips, S5P_VA_GPIO2);
+
+ /* gpio part3 */
+ chip = exynos4_gpios_3;
+ nr_chips = ARRAY_SIZE(exynos4_gpios_3);
+
+ for (i = 0; i < nr_chips; i++, chip++) {
+ if (!chip->config) {
+ chip->config = &exynos4_gpio_cfg;
+ chip->group = group++;
+ }
+ }
+ samsung_gpiolib_add_4bit_chips(chip, nr_chips, S5P_VA_GPIO3);
+
+#if defined(CONFIG_SOC_EXYNOS4210) && defined(CONFIG_S5P_GPIO_INT)
+ s5p_register_gpioint_bank(IRQ_GPIO_XA, 0, IRQ_GPIO1_NR_GROUPS);
+ s5p_register_gpioint_bank(IRQ_GPIO_XB, IRQ_GPIO1_NR_GROUPS, IRQ_GPIO2_NR_GROUPS);
+#endif
+ }
+
+ return 0;
+}
+core_initcall(samsung_gpiolib_init);
+
+int s3c_gpio_cfgpin(unsigned int pin, unsigned int config)
+{
+ struct samsung_gpio_chip *chip = samsung_gpiolib_getchip(pin);
+ unsigned long flags;
+ int offset;
+ int ret;
+
+ if (!chip)
+ return -EINVAL;
+
+ offset = pin - chip->chip.base;
+
+ samsung_gpio_lock(chip, flags);
+ ret = samsung_gpio_do_setcfg(chip, offset, config);
+ samsung_gpio_unlock(chip, flags);
+
+ return ret;
+}
+EXPORT_SYMBOL(s3c_gpio_cfgpin);
+
+int s3c_gpio_cfgpin_range(unsigned int start, unsigned int nr,
+ unsigned int cfg)
+{
+ int ret;
+
+ for (; nr > 0; nr--, start++) {
+ ret = s3c_gpio_cfgpin(start, cfg);
+ if (ret != 0)
+ return ret;
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(s3c_gpio_cfgpin_range);
+
+int s3c_gpio_cfgall_range(unsigned int start, unsigned int nr,
+ unsigned int cfg, samsung_gpio_pull_t pull)
+{
+ int ret;
+
+ for (; nr > 0; nr--, start++) {
+ s3c_gpio_setpull(start, pull);
+ ret = s3c_gpio_cfgpin(start, cfg);
+ if (ret != 0)
+ return ret;
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(s3c_gpio_cfgall_range);
+
+unsigned s3c_gpio_getcfg(unsigned int pin)
+{
+ struct samsung_gpio_chip *chip = samsung_gpiolib_getchip(pin);
+ unsigned long flags;
+ unsigned ret = 0;
+ int offset;
+
+ if (chip) {
+ offset = pin - chip->chip.base;
+
+ samsung_gpio_lock(chip, flags);
+ ret = samsung_gpio_do_getcfg(chip, offset);
+ samsung_gpio_unlock(chip, flags);
+ }
+
+ return ret;
+}
+EXPORT_SYMBOL(s3c_gpio_getcfg);
+
+int s3c_gpio_setpull(unsigned int pin, samsung_gpio_pull_t pull)
+{
+ struct samsung_gpio_chip *chip = samsung_gpiolib_getchip(pin);
+ unsigned long flags;
+ int offset, ret;
+
+ if (!chip)
+ return -EINVAL;
+
+ offset = pin - chip->chip.base;
+
+ samsung_gpio_lock(chip, flags);
+ ret = samsung_gpio_do_setpull(chip, offset, pull);
+ samsung_gpio_unlock(chip, flags);
+
+ return ret;
+}
+EXPORT_SYMBOL(s3c_gpio_setpull);
+
+samsung_gpio_pull_t s3c_gpio_getpull(unsigned int pin)
+{
+ struct samsung_gpio_chip *chip = samsung_gpiolib_getchip(pin);
+ unsigned long flags;
+ int offset;
+ u32 pup = 0;
+
+ if (chip) {
+ offset = pin - chip->chip.base;
+
+ samsung_gpio_lock(chip, flags);
+ pup = samsung_gpio_do_getpull(chip, offset);
+ samsung_gpio_unlock(chip, flags);
+ }
+
+ return (__force samsung_gpio_pull_t)pup;
+}
+EXPORT_SYMBOL(s3c_gpio_getpull);
+
+/* gpiolib wrappers until these are totally eliminated */
+
+void s3c2410_gpio_pullup(unsigned int pin, unsigned int to)
+{
+ int ret;
+
+ WARN_ON(to); /* should be none of these left */
+
+ if (!to) {
+ /* if pull is enabled, try first with up, and if that
+ * fails, try using down */
+
+ ret = s3c_gpio_setpull(pin, S3C_GPIO_PULL_UP);
+ if (ret)
+ s3c_gpio_setpull(pin, S3C_GPIO_PULL_DOWN);
+ } else {
+ s3c_gpio_setpull(pin, S3C_GPIO_PULL_NONE);
+ }
+}
+EXPORT_SYMBOL(s3c2410_gpio_pullup);
+
+void s3c2410_gpio_setpin(unsigned int pin, unsigned int to)
+{
+ /* do this via gpiolib until all users removed */
+
+ gpio_request(pin, "temporary");
+ gpio_set_value(pin, to);
+ gpio_free(pin);
+}
+EXPORT_SYMBOL(s3c2410_gpio_setpin);
+
+unsigned int s3c2410_gpio_getpin(unsigned int pin)
+{
+ struct samsung_gpio_chip *chip = samsung_gpiolib_getchip(pin);
+ unsigned long offs = pin - chip->chip.base;
+
+ return __raw_readl(chip->base + 0x04) & (1 << offs);
+}
+EXPORT_SYMBOL(s3c2410_gpio_getpin);
+
+#ifdef CONFIG_S5P_GPIO_DRVSTR
+s5p_gpio_drvstr_t s5p_gpio_get_drvstr(unsigned int pin)
+{
+ struct samsung_gpio_chip *chip = samsung_gpiolib_getchip(pin);
+ unsigned int off;
+ void __iomem *reg;
+ int shift;
+ u32 drvstr;
+
+ if (!chip)
+ return -EINVAL;
+
+ off = pin - chip->chip.base;
+ shift = off * 2;
+ reg = chip->base + 0x0C;
+
+ drvstr = __raw_readl(reg);
+ drvstr = drvstr >> shift;
+ drvstr &= 0x3;
+
+ return (__force s5p_gpio_drvstr_t)drvstr;
+}
+EXPORT_SYMBOL(s5p_gpio_get_drvstr);
+
+int s5p_gpio_set_drvstr(unsigned int pin, s5p_gpio_drvstr_t drvstr)
+{
+ struct samsung_gpio_chip *chip = samsung_gpiolib_getchip(pin);
+ unsigned int off;
+ void __iomem *reg;
+ int shift;
+ u32 tmp;
+
+ if (!chip)
+ return -EINVAL;
+
+ off = pin - chip->chip.base;
+ shift = off * 2;
+ reg = chip->base + 0x0C;
+
+ tmp = __raw_readl(reg);
+ tmp &= ~(0x3 << shift);
+ tmp |= drvstr << shift;
+
+ __raw_writel(tmp, reg);
+
+ return 0;
+}
+EXPORT_SYMBOL(s5p_gpio_set_drvstr);
+#endif /* CONFIG_S5P_GPIO_DRVSTR */
+
+#ifdef CONFIG_PLAT_S3C24XX
+unsigned int s3c2410_modify_misccr(unsigned int clear, unsigned int change)
+{
+ unsigned long flags;
+ unsigned long misccr;
+
+ local_irq_save(flags);
+ misccr = __raw_readl(S3C24XX_MISCCR);
+ misccr &= ~clear;
+ misccr ^= change;
+ __raw_writel(misccr, S3C24XX_MISCCR);
+ local_irq_restore(flags);
+
+ return misccr;
+}
+EXPORT_SYMBOL(s3c2410_modify_misccr);
+#endif
This patch adds support for Samsung GPIOs with one gpio driver. Actually there are drivers/gpio-s3c24xx.c, gpio-s3c64xx.c, gpio-s5p64x0.c, gpio-s5pc100.c, gpio-s5pv210.c, gpio-exynos4.c, gpio-plat-samsung.c, plat-samsung/gpio-config.c and gpio.c to support each Samsung SoCs before. Basically, the gpio-samsung.c has been made by their merging and removing duplicated definitions. Note: gpio-samsung.c includes some SoC dependent codes and it will be replaced next time. Cc: Ben Dooks <ben-linux@fluff.org> Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com> --- drivers/gpio/Makefile | 1 + drivers/gpio/gpio-samsung.c | 2686 +++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 2687 insertions(+), 0 deletions(-) create mode 100644 drivers/gpio/gpio-samsung.c