new file mode 100644
@@ -0,0 +1,100 @@
+* Clock bindings for Freescale i.MX28
+
+Required properties:
+- compatible: Should be "fsl,imx28-clkctrl"
+- reg: Address and length of the register set
+- #clock-cells: Should be <1>
+- clock-output-names: A list of clock output names that i.MX28 CLKCTRL
+ provides. The full list of all valid clock names and IDs is below.
+
+ Name ID
+ ------------------
+ ref_xtal 0
+ pll0 1
+ pll1 2
+ pll2 3
+ ref_cpu 4
+ ref_emi 5
+ ref_io0 6
+ ref_io1 7
+ ref_pix 8
+ ref_hsadc 9
+ ref_gpmi 10
+ saif0_sel 11
+ saif1_sel 12
+ gpmi_sel 13
+ ssp0_sel 14
+ ssp1_sel 15
+ ssp2_sel 16
+ ssp3_sel 17
+ emi_sel 18
+ etm_sel 19
+ lcdif_sel 20
+ cpu 21
+ ptp_sel 22
+ cpu_pll 23
+ cpu_xtal 24
+ hbus 25
+ xbus 26
+ ssp0_div 27
+ ssp1_div 28
+ ssp2_div 29
+ ssp3_div 30
+ gpmi_div 31
+ emi_pll 32
+ emi_xtal 33
+ lcdif_div 34
+ etm_div 35
+ ptp 36
+ saif0_div 37
+ saif1_div 38
+ clk32k_div 39
+ rtc 40
+ lradc 41
+ spdif_div 42
+ clk32k 43
+ pwm 44
+ uart 45
+ ssp0 46
+ ssp1 47
+ ssp2 48
+ ssp3 49
+ gpmi 50
+ spdif 51
+ emi 52
+ saif0 53
+ saif1 54
+ lcdif 55
+ etm 56
+ fec 57
+ can0 58
+ can1 59
+ usb0 60
+ usb1 61
+ usb0_pwr 62
+ usb1_pwr 63
+ enet_out 64
+
+ The ID will be used by clock consumer in the first cell of "clocks"
+ phandle to specify the desired clock.
+
+Examples:
+
+clks: clkctrl@80040000 {
+ compatible = "fsl,imx28-clkctrl";
+ reg = <0x80040000 0x2000>;
+ #clock-cells = <1>;
+ clock-output-names =
+ ...
+ "uart", /* 45 */
+ ...
+ "end_of_list";
+};
+
+auart0: serial@8006a000 {
+ compatible = "fsl,imx28-auart", "fsl,imx23-auart";
+ reg = <0x8006a000 0x2000>;
+ interrupts = <112 70 71>;
+ clocks = <&clks 45>;
+ status = "disabled";
+};
@@ -65,6 +65,7 @@
dma-apbh@80004000 {
compatible = "fsl,imx28-dma-apbh";
reg = <0x80004000 0x2000>;
+ clocks = <&clks 25>;
};
perfmon@80006000 {
@@ -81,6 +82,7 @@
reg-names = "gpmi-nand", "bch";
interrupts = <88>, <41>;
interrupt-names = "gpmi-dma", "bch";
+ clocks = <&clks 50>;
fsl,gpmi-dma-channel = <4>;
status = "disabled";
};
@@ -88,6 +90,7 @@
ssp0: ssp@80010000 {
reg = <0x80010000 0x2000>;
interrupts = <96 82>;
+ clocks = <&clks 46>;
fsl,ssp-dma-channel = <0>;
status = "disabled";
};
@@ -95,6 +98,7 @@
ssp1: ssp@80012000 {
reg = <0x80012000 0x2000>;
interrupts = <97 83>;
+ clocks = <&clks 47>;
fsl,ssp-dma-channel = <1>;
status = "disabled";
};
@@ -102,6 +106,7 @@
ssp2: ssp@80014000 {
reg = <0x80014000 0x2000>;
interrupts = <98 84>;
+ clocks = <&clks 48>;
fsl,ssp-dma-channel = <2>;
status = "disabled";
};
@@ -109,6 +114,7 @@
ssp3: ssp@80016000 {
reg = <0x80016000 0x2000>;
interrupts = <99 85>;
+ clocks = <&clks 49>;
fsl,ssp-dma-channel = <3>;
status = "disabled";
};
@@ -523,6 +529,7 @@
dma-apbx@80024000 {
compatible = "fsl,imx28-dma-apbx";
reg = <0x80024000 0x2000>;
+ clocks = <&clks 26>;
};
dcp@80028000 {
@@ -551,6 +558,7 @@
compatible = "fsl,imx28-lcdif";
reg = <0x80030000 0x2000>;
interrupts = <38 86>;
+ clocks = <&clks 55>;
status = "disabled";
};
@@ -558,6 +566,7 @@
compatible = "fsl,imx28-flexcan", "fsl,p1010-flexcan";
reg = <0x80032000 0x2000>;
interrupts = <8>;
+ clocks = <&clks 58>;
status = "disabled";
};
@@ -565,6 +574,7 @@
compatible = "fsl,imx28-flexcan", "fsl,p1010-flexcan";
reg = <0x80034000 0x2000>;
interrupts = <9>;
+ clocks = <&clks 59>;
status = "disabled";
};
@@ -611,15 +621,84 @@
reg = <0x80040000 0x40000>;
ranges;
- clkctl@80040000 {
+ clks: clkctrl@80040000 {
+ compatible = "fsl,imx28-clkctrl";
reg = <0x80040000 0x2000>;
- status = "disabled";
+ #clock-cells = <1>;
+ clock-output-names =
+ "ref_xtal", /* 0 */
+ "pll0", /* 1 */
+ "pll1", /* 2 */
+ "pll2", /* 3 */
+ "ref_cpu", /* 4 */
+ "ref_emi", /* 5 */
+ "ref_io0", /* 6 */
+ "ref_io1", /* 7 */
+ "ref_pix", /* 8 */
+ "ref_hsadc", /* 9 */
+ "ref_gpmi", /* 10 */
+ "saif0_sel", /* 11 */
+ "saif1_sel", /* 12 */
+ "gpmi_sel", /* 13 */
+ "ssp0_sel", /* 14 */
+ "ssp1_sel", /* 15 */
+ "ssp2_sel", /* 16 */
+ "ssp3_sel", /* 17 */
+ "emi_sel", /* 18 */
+ "etm_sel", /* 19 */
+ "lcdif_sel", /* 20 */
+ "cpu", /* 21 */
+ "ptp_sel", /* 22 */
+ "cpu_pll", /* 23 */
+ "cpu_xtal", /* 24 */
+ "hbus", /* 25 */
+ "xbus", /* 26 */
+ "ssp0_div", /* 27 */
+ "ssp1_div", /* 28 */
+ "ssp2_div", /* 29 */
+ "ssp3_div", /* 30 */
+ "gpmi_div", /* 31 */
+ "emi_pll", /* 32 */
+ "emi_xtal", /* 33 */
+ "lcdif_div", /* 34 */
+ "etm_div", /* 35 */
+ "ptp", /* 36 */
+ "saif0_div", /* 37 */
+ "saif1_div", /* 38 */
+ "clk32k_div", /* 39 */
+ "rtc", /* 40 */
+ "lradc", /* 41 */
+ "spdif_div", /* 42 */
+ "clk32k", /* 43 */
+ "pwm", /* 44 */
+ "uart", /* 45 */
+ "ssp0", /* 46 */
+ "ssp1", /* 47 */
+ "ssp2", /* 48 */
+ "ssp3", /* 49 */
+ "gpmi", /* 50 */
+ "spdif", /* 51 */
+ "emi", /* 52 */
+ "saif0", /* 53 */
+ "saif1", /* 54 */
+ "lcdif", /* 55 */
+ "etm", /* 56 */
+ "fec", /* 57 */
+ "can0", /* 58 */
+ "can1", /* 59 */
+ "usb0", /* 60 */
+ "usb1", /* 61 */
+ "usb0_pwr", /* 62 */
+ "usb1_pwr", /* 63 */
+ "enet_out", /* 64 */
+ "end_of_list";
};
saif0: saif@80042000 {
compatible = "fsl,imx28-saif";
reg = <0x80042000 0x2000>;
interrupts = <59 80>;
+ clocks = <&clks 53>;
fsl,saif-dma-channel = <4>;
status = "disabled";
};
@@ -633,6 +712,7 @@
compatible = "fsl,imx28-saif";
reg = <0x80046000 0x2000>;
interrupts = <58 81>;
+ clocks = <&clks 54>;
fsl,saif-dma-channel = <5>;
status = "disabled";
};
@@ -680,6 +760,7 @@
pwm: pwm@80064000 {
compatible = "fsl,imx28-pwm", "fsl,imx23-pwm";
reg = <0x80064000 0x2000>;
+ clocks = <&clks 44>;
#pwm-cells = <2>;
fsl,pwm-number = <8>;
status = "disabled";
@@ -694,6 +775,7 @@
compatible = "fsl,imx28-auart", "fsl,imx23-auart";
reg = <0x8006a000 0x2000>;
interrupts = <112 70 71>;
+ clocks = <&clks 45>;
status = "disabled";
};
@@ -701,6 +783,7 @@
compatible = "fsl,imx28-auart", "fsl,imx23-auart";
reg = <0x8006c000 0x2000>;
interrupts = <113 72 73>;
+ clocks = <&clks 45>;
status = "disabled";
};
@@ -708,6 +791,7 @@
compatible = "fsl,imx28-auart", "fsl,imx23-auart";
reg = <0x8006e000 0x2000>;
interrupts = <114 74 75>;
+ clocks = <&clks 45>;
status = "disabled";
};
@@ -715,6 +799,7 @@
compatible = "fsl,imx28-auart", "fsl,imx23-auart";
reg = <0x80070000 0x2000>;
interrupts = <115 76 77>;
+ clocks = <&clks 45>;
status = "disabled";
};
@@ -722,6 +807,7 @@
compatible = "fsl,imx28-auart", "fsl,imx23-auart";
reg = <0x80072000 0x2000>;
interrupts = <116 78 79>;
+ clocks = <&clks 45>;
status = "disabled";
};
@@ -729,18 +815,22 @@
compatible = "arm,pl011", "arm,primecell";
reg = <0x80074000 0x1000>;
interrupts = <47>;
+ clocks = <&clks 45>, <&clks 26>;
+ clock-names = "uart", "apb_pclk";
status = "disabled";
};
usbphy0: usbphy@8007c000 {
compatible = "fsl,imx28-usbphy", "fsl,imx23-usbphy";
reg = <0x8007c000 0x2000>;
+ clocks = <&clks 62>;
status = "disabled";
};
usbphy1: usbphy@8007e000 {
compatible = "fsl,imx28-usbphy", "fsl,imx23-usbphy";
reg = <0x8007e000 0x2000>;
+ clocks = <&clks 63>;
status = "disabled";
};
};
@@ -757,6 +847,7 @@
compatible = "fsl,imx28-usb", "fsl,imx27-usb";
reg = <0x80080000 0x10000>;
interrupts = <93>;
+ clocks = <&clks 60>;
fsl,usbphy = <&usbphy0>;
status = "disabled";
};
@@ -765,6 +856,7 @@
compatible = "fsl,imx28-usb", "fsl,imx27-usb";
reg = <0x80090000 0x10000>;
interrupts = <92>;
+ clocks = <&clks 61>;
fsl,usbphy = <&usbphy1>;
status = "disabled";
};
@@ -778,6 +870,8 @@
compatible = "fsl,imx28-fec";
reg = <0x800f0000 0x4000>;
interrupts = <101>;
+ clocks = <&clks 57>, <&clks 57>;
+ clock-names = "ipg", "ahb";
status = "disabled";
};
@@ -785,6 +879,8 @@
compatible = "fsl,imx28-fec";
reg = <0x800f4000 0x4000>;
interrupts = <102>;
+ clocks = <&clks 57>, <&clks 57>;
+ clock-names = "ipg", "ahb";
status = "disabled";
};
@@ -14,6 +14,7 @@
#include <linux/err.h>
#include <linux/init.h>
#include <linux/io.h>
+#include <linux/of.h>
#include <mach/common.h>
#include <mach/mx28.h>
#include "clk.h"
@@ -120,90 +121,6 @@ static void __init clk_misc_init(void)
writel_relaxed(val, FRAC0);
}
-static struct clk_lookup uart_lookups[] = {
- { .dev_id = "duart", },
- { .dev_id = "mxs-auart.0", },
- { .dev_id = "mxs-auart.1", },
- { .dev_id = "mxs-auart.2", },
- { .dev_id = "mxs-auart.3", },
- { .dev_id = "mxs-auart.4", },
- { .dev_id = "8006a000.serial", },
- { .dev_id = "8006c000.serial", },
- { .dev_id = "8006e000.serial", },
- { .dev_id = "80070000.serial", },
- { .dev_id = "80072000.serial", },
- { .dev_id = "80074000.serial", },
-};
-
-static struct clk_lookup hbus_lookups[] = {
- { .dev_id = "imx28-dma-apbh", },
- { .dev_id = "80004000.dma-apbh", },
-};
-
-static struct clk_lookup xbus_lookups[] = {
- { .dev_id = "duart", .con_id = "apb_pclk"},
- { .dev_id = "80074000.serial", .con_id = "apb_pclk"},
- { .dev_id = "imx28-dma-apbx", },
- { .dev_id = "80024000.dma-apbx", },
-};
-
-static struct clk_lookup ssp0_lookups[] = {
- { .dev_id = "imx28-mmc.0", },
- { .dev_id = "80010000.ssp", },
-};
-
-static struct clk_lookup ssp1_lookups[] = {
- { .dev_id = "imx28-mmc.1", },
- { .dev_id = "80012000.ssp", },
-};
-
-static struct clk_lookup ssp2_lookups[] = {
- { .dev_id = "imx28-mmc.2", },
- { .dev_id = "80014000.ssp", },
-};
-
-static struct clk_lookup ssp3_lookups[] = {
- { .dev_id = "imx28-mmc.3", },
- { .dev_id = "80016000.ssp", },
-};
-
-static struct clk_lookup lcdif_lookups[] = {
- { .dev_id = "imx28-fb", },
- { .dev_id = "80030000.lcdif", },
-};
-
-static struct clk_lookup gpmi_lookups[] = {
- { .dev_id = "imx28-gpmi-nand", },
- { .dev_id = "8000c000.gpmi-nand", },
-};
-
-static struct clk_lookup fec_lookups[] = {
- { .dev_id = "imx28-fec.0", },
- { .dev_id = "imx28-fec.1", },
- { .dev_id = "800f0000.ethernet", },
- { .dev_id = "800f4000.ethernet", },
-};
-
-static struct clk_lookup can0_lookups[] = {
- { .dev_id = "flexcan.0", },
- { .dev_id = "80032000.can", },
-};
-
-static struct clk_lookup can1_lookups[] = {
- { .dev_id = "flexcan.1", },
- { .dev_id = "80034000.can", },
-};
-
-static struct clk_lookup saif0_lookups[] = {
- { .dev_id = "mxs-saif.0", },
- { .dev_id = "80042000.saif", },
-};
-
-static struct clk_lookup saif1_lookups[] = {
- { .dev_id = "mxs-saif.1", },
- { .dev_id = "80046000.saif", },
-};
-
static const char *sel_cpu[] __initconst = { "ref_cpu", "ref_xtal", };
static const char *sel_io0[] __initconst = { "ref_io0", "ref_xtal", };
static const char *sel_io1[] __initconst = { "ref_io1", "ref_xtal", };
@@ -235,6 +152,7 @@ static enum imx28_clk clks_init_on[] __initdata = {
int __init mx28_clocks_init(void)
{
+ struct device_node *np;
int i;
clk_misc_init();
@@ -312,27 +230,12 @@ int __init mx28_clocks_init(void)
return PTR_ERR(clks[i]);
}
+ np = of_find_compatible_node(NULL, NULL, "fsl,imx28-clkctrl");
+ if (np)
+ of_clk_add_provider(np, of_clk_src_onecell_get, NULL);
+
clk_register_clkdev(clks[clk32k], NULL, "timrot");
clk_register_clkdev(clks[enet_out], NULL, "enet_out");
- clk_register_clkdev(clks[pwm], NULL, "80064000.pwm");
- clk_register_clkdevs(clks[hbus], hbus_lookups, ARRAY_SIZE(hbus_lookups));
- clk_register_clkdevs(clks[xbus], xbus_lookups, ARRAY_SIZE(xbus_lookups));
- clk_register_clkdevs(clks[uart], uart_lookups, ARRAY_SIZE(uart_lookups));
- clk_register_clkdevs(clks[ssp0], ssp0_lookups, ARRAY_SIZE(ssp0_lookups));
- clk_register_clkdevs(clks[ssp1], ssp1_lookups, ARRAY_SIZE(ssp1_lookups));
- clk_register_clkdevs(clks[ssp2], ssp2_lookups, ARRAY_SIZE(ssp2_lookups));
- clk_register_clkdevs(clks[ssp3], ssp3_lookups, ARRAY_SIZE(ssp3_lookups));
- clk_register_clkdevs(clks[gpmi], gpmi_lookups, ARRAY_SIZE(gpmi_lookups));
- clk_register_clkdevs(clks[saif0], saif0_lookups, ARRAY_SIZE(saif0_lookups));
- clk_register_clkdevs(clks[saif1], saif1_lookups, ARRAY_SIZE(saif1_lookups));
- clk_register_clkdevs(clks[lcdif], lcdif_lookups, ARRAY_SIZE(lcdif_lookups));
- clk_register_clkdevs(clks[fec], fec_lookups, ARRAY_SIZE(fec_lookups));
- clk_register_clkdevs(clks[can0], can0_lookups, ARRAY_SIZE(can0_lookups));
- clk_register_clkdevs(clks[can1], can1_lookups, ARRAY_SIZE(can1_lookups));
- clk_register_clkdev(clks[usb0_pwr], NULL, "8007c000.usbphy");
- clk_register_clkdev(clks[usb1_pwr], NULL, "8007e000.usbphy");
- clk_register_clkdev(clks[usb0], NULL, "80080000.usb");
- clk_register_clkdev(clks[usb1], NULL, "80090000.usb");
for (i = 0; i < ARRAY_SIZE(clks_init_on); i++)
clk_prepare_enable(clks[clks_init_on[i]]);
It really becomes a maintenance issue that every time a device needs to look up (clk_get) a clock we have to patch kernel clock file to call clk_register_clkdev for that clock. Since clock DT support which is meant to resolve clock lookup in device tree is in place, the patch moves imx28 client devices' clock lookup over to device tree, so that any new lookup to be added at later time can just get done in DT instead of kernel. Signed-off-by: Shawn Guo <shawn.guo@linaro.org> --- .../devicetree/bindings/clock/imx28-clock.txt | 100 ++++++++++++++++++ arch/arm/boot/dts/imx28.dtsi | 100 ++++++++++++++++++- drivers/clk/mxs/clk-imx28.c | 109 +------------------ 3 files changed, 204 insertions(+), 105 deletions(-) create mode 100644 Documentation/devicetree/bindings/clock/imx28-clock.txt