@@ -709,14 +709,6 @@ config ARCH_PICOXCELL
family of Femtocell devices. The picoxcell support requires device tree
for all boards.
-config ARCH_PNX4008
- bool "Philips Nexperia PNX4008 Mobile"
- select CPU_ARM926T
- select CLKDEV_LOOKUP
- select ARCH_USES_GETTIMEOFFSET
- help
- This enables support for Philips PNX4008 mobile platform.
-
config ARCH_PXA
bool "PXA2xx/PXA3xx-based"
depends on MMU
@@ -167,7 +167,6 @@ machine-$(CONFIG_ARCH_OMAP1) := omap1
machine-$(CONFIG_ARCH_OMAP2PLUS) := omap2
machine-$(CONFIG_ARCH_ORION5X) := orion5x
machine-$(CONFIG_ARCH_PICOXCELL) := picoxcell
-machine-$(CONFIG_ARCH_PNX4008) := pnx4008
machine-$(CONFIG_ARCH_PRIMA2) := prima2
machine-$(CONFIG_ARCH_PXA) := pxa
machine-$(CONFIG_ARCH_REALVIEW) := realview
@@ -1,472 +0,0 @@
-CONFIG_EXPERIMENTAL=y
-CONFIG_SYSVIPC=y
-CONFIG_POSIX_MQUEUE=y
-CONFIG_BSD_PROCESS_ACCT=y
-CONFIG_AUDIT=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_EXPERT=y
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-CONFIG_MODVERSIONS=y
-CONFIG_MODULE_SRCVERSION_ALL=y
-CONFIG_ARCH_PNX4008=y
-CONFIG_PREEMPT=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="mem=64M console=ttyS0,115200"
-CONFIG_FPE_NWFPE=y
-CONFIG_BINFMT_AOUT=m
-CONFIG_BINFMT_MISC=m
-CONFIG_PM=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_MULTICAST=y
-CONFIG_IP_ADVANCED_ROUTER=y
-CONFIG_IP_MULTIPLE_TABLES=y
-CONFIG_IP_ROUTE_MULTIPATH=y
-CONFIG_IP_ROUTE_VERBOSE=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-CONFIG_IP_MROUTE=y
-CONFIG_IP_PIMSM_V1=y
-CONFIG_IP_PIMSM_V2=y
-CONFIG_SYN_COOKIES=y
-CONFIG_INET_AH=m
-CONFIG_INET_ESP=m
-CONFIG_INET_IPCOMP=m
-CONFIG_IPV6_PRIVACY=y
-CONFIG_INET6_AH=m
-CONFIG_INET6_ESP=m
-CONFIG_INET6_IPCOMP=m
-CONFIG_IPV6_TUNNEL=m
-CONFIG_NETFILTER=y
-CONFIG_IP_VS=m
-CONFIG_IP_VS_PROTO_TCP=y
-CONFIG_IP_VS_PROTO_UDP=y
-CONFIG_IP_VS_PROTO_ESP=y
-CONFIG_IP_VS_PROTO_AH=y
-CONFIG_IP_VS_RR=m
-CONFIG_IP_VS_WRR=m
-CONFIG_IP_VS_LC=m
-CONFIG_IP_VS_WLC=m
-CONFIG_IP_VS_LBLC=m
-CONFIG_IP_VS_LBLCR=m
-CONFIG_IP_VS_DH=m
-CONFIG_IP_VS_SH=m
-CONFIG_IP_VS_SED=m
-CONFIG_IP_VS_NQ=m
-CONFIG_IP_VS_FTP=m
-CONFIG_IP_NF_QUEUE=m
-CONFIG_IP6_NF_QUEUE=m
-CONFIG_DECNET_NF_GRABULATOR=m
-CONFIG_BRIDGE_NF_EBTABLES=m
-CONFIG_BRIDGE_EBT_BROUTE=m
-CONFIG_BRIDGE_EBT_T_FILTER=m
-CONFIG_BRIDGE_EBT_T_NAT=m
-CONFIG_BRIDGE_EBT_802_3=m
-CONFIG_BRIDGE_EBT_AMONG=m
-CONFIG_BRIDGE_EBT_ARP=m
-CONFIG_BRIDGE_EBT_IP=m
-CONFIG_BRIDGE_EBT_LIMIT=m
-CONFIG_BRIDGE_EBT_MARK=m
-CONFIG_BRIDGE_EBT_PKTTYPE=m
-CONFIG_BRIDGE_EBT_STP=m
-CONFIG_BRIDGE_EBT_VLAN=m
-CONFIG_BRIDGE_EBT_ARPREPLY=m
-CONFIG_BRIDGE_EBT_DNAT=m
-CONFIG_BRIDGE_EBT_MARK_T=m
-CONFIG_BRIDGE_EBT_REDIRECT=m
-CONFIG_BRIDGE_EBT_SNAT=m
-CONFIG_BRIDGE_EBT_LOG=m
-CONFIG_IP_SCTP=m
-CONFIG_ATM=y
-CONFIG_ATM_CLIP=y
-CONFIG_ATM_LANE=m
-CONFIG_ATM_MPOA=m
-CONFIG_ATM_BR2684=m
-CONFIG_BRIDGE=m
-CONFIG_VLAN_8021Q=m
-CONFIG_DECNET=m
-CONFIG_LLC2=m
-CONFIG_IPX=m
-CONFIG_ATALK=m
-CONFIG_DEV_APPLETALK=m
-CONFIG_IPDDP=m
-CONFIG_IPDDP_ENCAP=y
-CONFIG_IPDDP_DECAP=y
-CONFIG_X25=m
-CONFIG_LAPB=m
-CONFIG_ECONET=m
-CONFIG_ECONET_AUNUDP=y
-CONFIG_ECONET_NATIVE=y
-CONFIG_WAN_ROUTER=m
-CONFIG_NET_SCHED=y
-CONFIG_NET_SCH_CBQ=m
-CONFIG_NET_SCH_HTB=m
-CONFIG_NET_SCH_HFSC=m
-CONFIG_NET_SCH_ATM=m
-CONFIG_NET_SCH_PRIO=m
-CONFIG_NET_SCH_RED=m
-CONFIG_NET_SCH_SFQ=m
-CONFIG_NET_SCH_TEQL=m
-CONFIG_NET_SCH_TBF=m
-CONFIG_NET_SCH_GRED=m
-CONFIG_NET_SCH_DSMARK=m
-CONFIG_NET_SCH_NETEM=m
-CONFIG_NET_CLS_TCINDEX=m
-CONFIG_NET_CLS_ROUTE4=m
-CONFIG_NET_CLS_FW=m
-CONFIG_NET_CLS_U32=m
-CONFIG_NET_CLS_RSVP=m
-CONFIG_NET_CLS_RSVP6=m
-CONFIG_NET_PKTGEN=m
-CONFIG_MTD=y
-CONFIG_MTD_CONCAT=y
-CONFIG_MTD_PARTITIONS=y
-CONFIG_MTD_REDBOOT_PARTS=y
-CONFIG_MTD_CHAR=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_SLRAM=m
-CONFIG_MTD_PHRAM=m
-CONFIG_MTD_MTDRAM=m
-CONFIG_MTD_DOC2000=m
-CONFIG_MTD_DOC2001=m
-CONFIG_MTD_DOC2001PLUS=m
-CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_NANDSIM=m
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_CRYPTOLOOP=y
-CONFIG_BLK_DEV_NBD=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_SIZE=8192
-CONFIG_CDROM_PKTCDVD=m
-CONFIG_EEPROM_LEGACY=m
-CONFIG_SCSI=m
-CONFIG_BLK_DEV_SD=m
-CONFIG_CHR_DEV_ST=m
-CONFIG_CHR_DEV_OSST=m
-CONFIG_BLK_DEV_SR=m
-CONFIG_CHR_DEV_SG=m
-CONFIG_CHR_DEV_SCH=m
-CONFIG_SCSI_MULTI_LUN=y
-CONFIG_SCSI_CONSTANTS=y
-CONFIG_SCSI_LOGGING=y
-CONFIG_SCSI_SPI_ATTRS=m
-CONFIG_SCSI_FC_ATTRS=m
-CONFIG_SCSI_DEBUG=m
-CONFIG_NETDEVICES=y
-CONFIG_DUMMY=m
-CONFIG_BONDING=m
-CONFIG_EQUALIZER=m
-CONFIG_TUN=m
-CONFIG_NET_ETHERNET=y
-CONFIG_USB_CATC=m
-CONFIG_USB_KAWETH=m
-CONFIG_USB_PEGASUS=m
-CONFIG_USB_RTL8150=m
-CONFIG_USB_USBNET=m
-# CONFIG_USB_NET_CDC_SUBSET is not set
-CONFIG_WAN=y
-CONFIG_HDLC=m
-CONFIG_HDLC_RAW=m
-CONFIG_HDLC_RAW_ETH=m
-CONFIG_HDLC_CISCO=m
-CONFIG_HDLC_FR=m
-CONFIG_HDLC_PPP=m
-CONFIG_HDLC_X25=m
-CONFIG_DLCI=m
-CONFIG_WAN_ROUTER_DRIVERS=m
-CONFIG_LAPBETHER=m
-CONFIG_X25_ASY=m
-CONFIG_ATM_TCP=m
-CONFIG_PPP=m
-CONFIG_PPP_MULTILINK=y
-CONFIG_PPP_FILTER=y
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_SYNC_TTY=m
-CONFIG_PPP_DEFLATE=m
-CONFIG_PPP_BSDCOMP=m
-CONFIG_PPP_MPPE=m
-CONFIG_PPPOE=m
-CONFIG_PPPOATM=m
-CONFIG_SLIP=m
-CONFIG_SLIP_COMPRESSED=y
-CONFIG_SLIP_SMART=y
-CONFIG_SLIP_MODE_SLIP6=y
-CONFIG_NETCONSOLE=m
-# CONFIG_INPUT_MOUSEDEV is not set
-CONFIG_INPUT_JOYDEV=m
-CONFIG_INPUT_EVDEV=m
-CONFIG_INPUT_EVBUG=m
-CONFIG_KEYBOARD_LKKBD=m
-CONFIG_KEYBOARD_NEWTON=m
-CONFIG_KEYBOARD_SUNKBD=m
-CONFIG_KEYBOARD_XTKBD=m
-CONFIG_MOUSE_PS2=m
-CONFIG_MOUSE_SERIAL=m
-CONFIG_MOUSE_VSXXXAA=m
-CONFIG_INPUT_JOYSTICK=y
-CONFIG_JOYSTICK_ANALOG=m
-CONFIG_JOYSTICK_A3D=m
-CONFIG_JOYSTICK_ADI=m
-CONFIG_JOYSTICK_COBRA=m
-CONFIG_JOYSTICK_GF2K=m
-CONFIG_JOYSTICK_GRIP=m
-CONFIG_JOYSTICK_GRIP_MP=m
-CONFIG_JOYSTICK_GUILLEMOT=m
-CONFIG_JOYSTICK_INTERACT=m
-CONFIG_JOYSTICK_SIDEWINDER=m
-CONFIG_JOYSTICK_TMDC=m
-CONFIG_JOYSTICK_IFORCE=m
-CONFIG_JOYSTICK_IFORCE_USB=y
-CONFIG_JOYSTICK_IFORCE_232=y
-CONFIG_JOYSTICK_WARRIOR=m
-CONFIG_JOYSTICK_MAGELLAN=m
-CONFIG_JOYSTICK_SPACEORB=m
-CONFIG_JOYSTICK_SPACEBALL=m
-CONFIG_JOYSTICK_STINGER=m
-CONFIG_JOYSTICK_JOYDUMP=m
-CONFIG_INPUT_TOUCHSCREEN=y
-CONFIG_TOUCHSCREEN_GUNZE=m
-CONFIG_INPUT_MISC=y
-CONFIG_INPUT_UINPUT=m
-CONFIG_SERIO_SERPORT=m
-CONFIG_SERIO_RAW=m
-CONFIG_GAMEPORT_NS558=m
-CONFIG_GAMEPORT_L4=m
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_EXTENDED=y
-CONFIG_SERIAL_8250_MANY_PORTS=y
-CONFIG_SERIAL_8250_SHARE_IRQ=y
-CONFIG_SERIAL_8250_RSA=y
-CONFIG_HW_RANDOM=y
-CONFIG_I2C=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_SPI=y
-CONFIG_SPI_BITBANG=y
-# CONFIG_HWMON is not set
-CONFIG_WATCHDOG=y
-CONFIG_SOFT_WATCHDOG=m
-CONFIG_USBPCWATCHDOG=m
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_SOUND=m
-CONFIG_SND=m
-CONFIG_SND_SEQUENCER=m
-CONFIG_SND_SEQ_DUMMY=m
-CONFIG_SND_MIXER_OSS=m
-CONFIG_SND_PCM_OSS=m
-CONFIG_SND_SEQUENCER_OSS=y
-CONFIG_SND_DUMMY=m
-CONFIG_SND_VIRMIDI=m
-CONFIG_SND_MTPAV=m
-CONFIG_SND_SERIAL_U16550=m
-CONFIG_SND_MPU401=m
-CONFIG_SND_USB_AUDIO=m
-CONFIG_SOUND_PRIME=m
-CONFIG_USB_HID=m
-CONFIG_USB_HIDDEV=y
-CONFIG_USB_KBD=m
-CONFIG_USB_MOUSE=m
-CONFIG_USB=y
-CONFIG_USB_DEVICEFS=y
-CONFIG_USB_MON=y
-CONFIG_USB_SL811_HCD=m
-CONFIG_USB_ACM=m
-CONFIG_USB_PRINTER=m
-CONFIG_USB_STORAGE=m
-CONFIG_USB_STORAGE_DATAFAB=m
-CONFIG_USB_STORAGE_FREECOM=m
-CONFIG_USB_STORAGE_USBAT=m
-CONFIG_USB_STORAGE_SDDR09=m
-CONFIG_USB_STORAGE_SDDR55=m
-CONFIG_USB_STORAGE_JUMPSHOT=m
-CONFIG_USB_MDC800=m
-CONFIG_USB_MICROTEK=m
-CONFIG_USB_SERIAL=m
-CONFIG_USB_SERIAL_GENERIC=y
-CONFIG_USB_SERIAL_BELKIN=m
-CONFIG_USB_SERIAL_WHITEHEAT=m
-CONFIG_USB_SERIAL_DIGI_ACCELEPORT=m
-CONFIG_USB_SERIAL_CYPRESS_M8=m
-CONFIG_USB_SERIAL_EMPEG=m
-CONFIG_USB_SERIAL_FTDI_SIO=m
-CONFIG_USB_SERIAL_VISOR=m
-CONFIG_USB_SERIAL_IPAQ=m
-CONFIG_USB_SERIAL_IR=m
-CONFIG_USB_SERIAL_EDGEPORT=m
-CONFIG_USB_SERIAL_EDGEPORT_TI=m
-CONFIG_USB_SERIAL_IPW=m
-CONFIG_USB_SERIAL_KEYSPAN_PDA=m
-CONFIG_USB_SERIAL_KEYSPAN=m
-CONFIG_USB_SERIAL_KLSI=m
-CONFIG_USB_SERIAL_KOBIL_SCT=m
-CONFIG_USB_SERIAL_MCT_U232=m
-CONFIG_USB_SERIAL_PL2303=m
-CONFIG_USB_SERIAL_SAFE=m
-CONFIG_USB_SERIAL_CYBERJACK=m
-CONFIG_USB_SERIAL_XIRCOM=m
-CONFIG_USB_SERIAL_OMNINET=m
-CONFIG_USB_RIO500=m
-CONFIG_USB_LEGOTOWER=m
-CONFIG_USB_LCD=m
-CONFIG_USB_LED=m
-CONFIG_USB_CYTHERM=m
-CONFIG_USB_TEST=m
-CONFIG_USB_ATM=m
-CONFIG_USB_SPEEDTOUCH=m
-CONFIG_USB_GADGET=m
-CONFIG_USB_GADGET_DUMMY_HCD=y
-CONFIG_USB_ZERO=m
-CONFIG_USB_ETH=m
-CONFIG_USB_GADGETFS=m
-CONFIG_USB_FILE_STORAGE=m
-CONFIG_USB_G_SERIAL=m
-CONFIG_MMC=m
-CONFIG_EXT2_FS=y
-CONFIG_EXT2_FS_XATTR=y
-CONFIG_EXT2_FS_POSIX_ACL=y
-CONFIG_EXT2_FS_SECURITY=y
-CONFIG_EXT3_FS=m
-CONFIG_EXT3_FS_POSIX_ACL=y
-CONFIG_EXT3_FS_SECURITY=y
-CONFIG_REISERFS_FS=m
-CONFIG_REISERFS_FS_XATTR=y
-CONFIG_REISERFS_FS_POSIX_ACL=y
-CONFIG_REISERFS_FS_SECURITY=y
-CONFIG_JFS_FS=m
-CONFIG_JFS_POSIX_ACL=y
-CONFIG_JFS_STATISTICS=y
-CONFIG_XFS_FS=m
-CONFIG_XFS_QUOTA=y
-CONFIG_XFS_POSIX_ACL=y
-CONFIG_XFS_RT=y
-CONFIG_INOTIFY=y
-CONFIG_QUOTA=y
-CONFIG_QFMT_V1=m
-CONFIG_QFMT_V2=m
-CONFIG_AUTOFS_FS=m
-CONFIG_AUTOFS4_FS=m
-CONFIG_ISO9660_FS=m
-CONFIG_JOLIET=y
-CONFIG_ZISOFS=y
-CONFIG_UDF_FS=m
-CONFIG_MSDOS_FS=m
-CONFIG_VFAT_FS=m
-CONFIG_NTFS_FS=m
-CONFIG_TMPFS=y
-CONFIG_ADFS_FS=m
-CONFIG_AFFS_FS=m
-CONFIG_HFS_FS=m
-CONFIG_HFSPLUS_FS=m
-CONFIG_BEFS_FS=m
-CONFIG_BFS_FS=m
-CONFIG_EFS_FS=m
-CONFIG_JFFS2_FS=m
-CONFIG_CRAMFS=y
-CONFIG_VXFS_FS=m
-CONFIG_MINIX_FS=m
-CONFIG_HPFS_FS=m
-CONFIG_QNX4FS_FS=m
-CONFIG_ROMFS_FS=m
-CONFIG_SYSV_FS=m
-CONFIG_UFS_FS=m
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_NFS_V4=y
-CONFIG_ROOT_NFS=y
-CONFIG_NFSD=m
-CONFIG_NFSD_V4=y
-CONFIG_RPCSEC_GSS_SPKM3=m
-CONFIG_SMB_FS=m
-CONFIG_CIFS=m
-CONFIG_NCP_FS=m
-CONFIG_NCPFS_PACKET_SIGNING=y
-CONFIG_NCPFS_IOCTL_LOCKING=y
-CONFIG_NCPFS_STRONG=y
-CONFIG_NCPFS_NFS_NS=y
-CONFIG_NCPFS_OS2_NS=y
-CONFIG_NCPFS_NLS=y
-CONFIG_NCPFS_EXTRAS=y
-CONFIG_CODA_FS=m
-CONFIG_AFS_FS=m
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_ACORN_PARTITION=y
-CONFIG_ACORN_PARTITION_ICS=y
-CONFIG_ACORN_PARTITION_RISCIX=y
-CONFIG_OSF_PARTITION=y
-CONFIG_AMIGA_PARTITION=y
-CONFIG_ATARI_PARTITION=y
-CONFIG_MAC_PARTITION=y
-CONFIG_BSD_DISKLABEL=y
-CONFIG_MINIX_SUBPARTITION=y
-CONFIG_SOLARIS_X86_PARTITION=y
-CONFIG_UNIXWARE_DISKLABEL=y
-CONFIG_LDM_PARTITION=y
-CONFIG_SGI_PARTITION=y
-CONFIG_ULTRIX_PARTITION=y
-CONFIG_SUN_PARTITION=y
-CONFIG_NLS_DEFAULT="cp437"
-CONFIG_NLS_CODEPAGE_437=m
-CONFIG_NLS_CODEPAGE_737=m
-CONFIG_NLS_CODEPAGE_775=m
-CONFIG_NLS_CODEPAGE_850=m
-CONFIG_NLS_CODEPAGE_852=m
-CONFIG_NLS_CODEPAGE_855=m
-CONFIG_NLS_CODEPAGE_857=m
-CONFIG_NLS_CODEPAGE_860=m
-CONFIG_NLS_CODEPAGE_861=m
-CONFIG_NLS_CODEPAGE_862=m
-CONFIG_NLS_CODEPAGE_863=m
-CONFIG_NLS_CODEPAGE_864=m
-CONFIG_NLS_CODEPAGE_865=m
-CONFIG_NLS_CODEPAGE_866=m
-CONFIG_NLS_CODEPAGE_869=m
-CONFIG_NLS_CODEPAGE_936=m
-CONFIG_NLS_CODEPAGE_950=m
-CONFIG_NLS_CODEPAGE_932=m
-CONFIG_NLS_CODEPAGE_949=m
-CONFIG_NLS_CODEPAGE_874=m
-CONFIG_NLS_ISO8859_8=m
-CONFIG_NLS_CODEPAGE_1250=m
-CONFIG_NLS_CODEPAGE_1251=m
-CONFIG_NLS_ASCII=m
-CONFIG_NLS_ISO8859_1=m
-CONFIG_NLS_ISO8859_2=m
-CONFIG_NLS_ISO8859_3=m
-CONFIG_NLS_ISO8859_4=m
-CONFIG_NLS_ISO8859_5=m
-CONFIG_NLS_ISO8859_6=m
-CONFIG_NLS_ISO8859_7=m
-CONFIG_NLS_ISO8859_9=m
-CONFIG_NLS_ISO8859_13=m
-CONFIG_NLS_ISO8859_14=m
-CONFIG_NLS_ISO8859_15=m
-CONFIG_NLS_KOI8_R=m
-CONFIG_NLS_KOI8_U=m
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_KERNEL=y
-CONFIG_DEBUG_MUTEXES=y
-# CONFIG_DEBUG_BUGVERBOSE is not set
-CONFIG_SECURITY=y
-CONFIG_CRYPTO_NULL=m
-CONFIG_CRYPTO_TEST=m
-CONFIG_CRYPTO_HMAC=y
-CONFIG_CRYPTO_MD4=m
-CONFIG_CRYPTO_MICHAEL_MIC=m
-CONFIG_CRYPTO_SHA256=m
-CONFIG_CRYPTO_SHA512=m
-CONFIG_CRYPTO_WP512=m
-CONFIG_CRYPTO_ANUBIS=m
-CONFIG_CRYPTO_BLOWFISH=m
-CONFIG_CRYPTO_CAST6=m
-CONFIG_CRYPTO_KHAZAD=m
-CONFIG_CRYPTO_SERPENT=m
-CONFIG_CRYPTO_TEA=m
-CONFIG_CRYPTO_TWOFISH=m
-CONFIG_CRC16=m
@@ -1,12 +0,0 @@
-#
-# Makefile for the linux kernel.
-#
-
-obj-y := core.o irq.o time.o clock.o gpio.o serial.o dma.o i2c.o
-obj-m :=
-obj-n :=
-obj- :=
-
-# Power Management
-obj-$(CONFIG_PM) += pm.o sleep.o
-
@@ -1,4 +0,0 @@
- zreladdr-y += 0x80008000
-params_phys-y := 0x80000100
-initrd_phys-y := 0x80800000
-
@@ -1,1001 +0,0 @@
-/*
- * arch/arm/mach-pnx4008/clock.c
- *
- * Clock control driver for PNX4008
- *
- * Authors: Vitaly Wool, Dmitry Chigirev <source@mvista.com>
- * Generic clock management functions are partially based on:
- * linux/arch/arm/mach-omap/clock.c
- *
- * 2005-2006 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/list.h>
-#include <linux/errno.h>
-#include <linux/device.h>
-#include <linux/err.h>
-#include <linux/delay.h>
-#include <linux/io.h>
-#include <linux/clkdev.h>
-
-#include <mach/hardware.h>
-#include <mach/clock.h>
-#include "clock.h"
-
-/*forward declaration*/
-static struct clk per_ck;
-static struct clk hclk_ck;
-static struct clk ck_1MHz;
-static struct clk ck_13MHz;
-static struct clk ck_pll1;
-static int local_set_rate(struct clk *clk, u32 rate);
-
-static inline void clock_lock(void)
-{
- local_irq_disable();
-}
-
-static inline void clock_unlock(void)
-{
- local_irq_enable();
-}
-
-static void propagate_rate(struct clk *clk)
-{
- struct clk *tmp_clk;
-
- tmp_clk = clk;
- while (tmp_clk->propagate_next) {
- tmp_clk = tmp_clk->propagate_next;
- local_set_rate(tmp_clk, tmp_clk->user_rate);
- }
-}
-
-static void clk_reg_disable(struct clk *clk)
-{
- if (clk->enable_reg)
- __raw_writel(__raw_readl(clk->enable_reg) &
- ~(1 << clk->enable_shift), clk->enable_reg);
-}
-
-static int clk_reg_enable(struct clk *clk)
-{
- if (clk->enable_reg)
- __raw_writel(__raw_readl(clk->enable_reg) |
- (1 << clk->enable_shift), clk->enable_reg);
- return 0;
-}
-
-static inline void clk_reg_disable1(struct clk *clk)
-{
- if (clk->enable_reg1)
- __raw_writel(__raw_readl(clk->enable_reg1) &
- ~(1 << clk->enable_shift1), clk->enable_reg1);
-}
-
-static inline void clk_reg_enable1(struct clk *clk)
-{
- if (clk->enable_reg1)
- __raw_writel(__raw_readl(clk->enable_reg1) |
- (1 << clk->enable_shift1), clk->enable_reg1);
-}
-
-static int clk_wait_for_pll_lock(struct clk *clk)
-{
- int i;
- i = 0;
- while (i++ < 0xFFF && !(__raw_readl(clk->scale_reg) & 1)) ; /*wait for PLL to lock */
-
- if (!(__raw_readl(clk->scale_reg) & 1)) {
- printk(KERN_ERR
- "%s ERROR: failed to lock, scale reg data: %x\n",
- clk->name, __raw_readl(clk->scale_reg));
- return -1;
- }
- return 0;
-}
-
-static int switch_to_dirty_13mhz(struct clk *clk)
-{
- int i;
- int ret;
- u32 tmp_reg;
-
- ret = 0;
-
- if (!clk->rate)
- clk_reg_enable1(clk);
-
- tmp_reg = __raw_readl(clk->parent_switch_reg);
- /*if 13Mhz clock selected, select 13'MHz (dirty) source from OSC */
- if (!(tmp_reg & 1)) {
- tmp_reg |= (1 << 1); /* Trigger switch to 13'MHz (dirty) clock */
- __raw_writel(tmp_reg, clk->parent_switch_reg);
- i = 0;
- while (i++ < 0xFFF && !(__raw_readl(clk->parent_switch_reg) & 1)) ; /*wait for 13'MHz selection status */
-
- if (!(__raw_readl(clk->parent_switch_reg) & 1)) {
- printk(KERN_ERR
- "%s ERROR: failed to select 13'MHz, parent sw reg data: %x\n",
- clk->name, __raw_readl(clk->parent_switch_reg));
- ret = -1;
- }
- }
-
- if (!clk->rate)
- clk_reg_disable1(clk);
-
- return ret;
-}
-
-static int switch_to_clean_13mhz(struct clk *clk)
-{
- int i;
- int ret;
- u32 tmp_reg;
-
- ret = 0;
-
- if (!clk->rate)
- clk_reg_enable1(clk);
-
- tmp_reg = __raw_readl(clk->parent_switch_reg);
- /*if 13'Mhz clock selected, select 13MHz (clean) source from OSC */
- if (tmp_reg & 1) {
- tmp_reg &= ~(1 << 1); /* Trigger switch to 13MHz (clean) clock */
- __raw_writel(tmp_reg, clk->parent_switch_reg);
- i = 0;
- while (i++ < 0xFFF && (__raw_readl(clk->parent_switch_reg) & 1)) ; /*wait for 13MHz selection status */
-
- if (__raw_readl(clk->parent_switch_reg) & 1) {
- printk(KERN_ERR
- "%s ERROR: failed to select 13MHz, parent sw reg data: %x\n",
- clk->name, __raw_readl(clk->parent_switch_reg));
- ret = -1;
- }
- }
-
- if (!clk->rate)
- clk_reg_disable1(clk);
-
- return ret;
-}
-
-static int set_13MHz_parent(struct clk *clk, struct clk *parent)
-{
- int ret = -EINVAL;
-
- if (parent == &ck_13MHz)
- ret = switch_to_clean_13mhz(clk);
- else if (parent == &ck_pll1)
- ret = switch_to_dirty_13mhz(clk);
-
- return ret;
-}
-
-#define PLL160_MIN_FCCO 156000
-#define PLL160_MAX_FCCO 320000
-
-/*
- * Calculate pll160 settings.
- * Possible input: up to 320MHz with step of clk->parent->rate.
- * In PNX4008 parent rate for pll160s may be either 1 or 13MHz.
- * Ignored paths: "feedback" (bit 13 set), "div-by-N".
- * Setting ARM PLL4 rate to 0 will put CPU into direct run mode.
- * Setting PLL5 and PLL3 rate to 0 will disable USB and DSP clock input.
- * Please refer to PNX4008 IC manual for details.
- */
-
-static int pll160_set_rate(struct clk *clk, u32 rate)
-{
- u32 tmp_reg, tmp_m, tmp_2p, i;
- u32 parent_rate;
- int ret = -EINVAL;
-
- parent_rate = clk->parent->rate;
-
- if (!parent_rate)
- goto out;
-
- /* set direct run for ARM or disable output for others */
- clk_reg_disable(clk);
-
- /* disable source input as well (ignored for ARM) */
- clk_reg_disable1(clk);
-
- tmp_reg = __raw_readl(clk->scale_reg);
- tmp_reg &= ~0x1ffff; /*clear all settings, power down */
- __raw_writel(tmp_reg, clk->scale_reg);
-
- rate -= rate % parent_rate; /*round down the input */
-
- if (rate > PLL160_MAX_FCCO)
- rate = PLL160_MAX_FCCO;
-
- if (!rate) {
- clk->rate = 0;
- ret = 0;
- goto out;
- }
-
- clk_reg_enable1(clk);
- tmp_reg = __raw_readl(clk->scale_reg);
-
- if (rate == parent_rate) {
- /*enter direct bypass mode */
- tmp_reg |= ((1 << 14) | (1 << 15));
- __raw_writel(tmp_reg, clk->scale_reg);
- clk->rate = parent_rate;
- clk_reg_enable(clk);
- ret = 0;
- goto out;
- }
-
- i = 0;
- for (tmp_2p = 1; tmp_2p < 16; tmp_2p <<= 1) {
- if (rate * tmp_2p >= PLL160_MIN_FCCO)
- break;
- i++;
- }
-
- if (tmp_2p > 1)
- tmp_reg |= ((i - 1) << 11);
- else
- tmp_reg |= (1 << 14); /*direct mode, no divide */
-
- tmp_m = rate * tmp_2p;
- tmp_m /= parent_rate;
-
- tmp_reg |= (tmp_m - 1) << 1; /*calculate M */
- tmp_reg |= (1 << 16); /*power up PLL */
- __raw_writel(tmp_reg, clk->scale_reg);
-
- if (clk_wait_for_pll_lock(clk) < 0) {
- clk_reg_disable(clk);
- clk_reg_disable1(clk);
-
- tmp_reg = __raw_readl(clk->scale_reg);
- tmp_reg &= ~0x1ffff; /*clear all settings, power down */
- __raw_writel(tmp_reg, clk->scale_reg);
- clk->rate = 0;
- ret = -EFAULT;
- goto out;
- }
-
- clk->rate = (tmp_m * parent_rate) / tmp_2p;
-
- if (clk->flags & RATE_PROPAGATES)
- propagate_rate(clk);
-
- clk_reg_enable(clk);
- ret = 0;
-
-out:
- return ret;
-}
-
-/*configure PER_CLK*/
-static int per_clk_set_rate(struct clk *clk, u32 rate)
-{
- u32 tmp;
-
- tmp = __raw_readl(clk->scale_reg);
- tmp &= ~(0x1f << 2);
- tmp |= ((clk->parent->rate / clk->rate) - 1) << 2;
- __raw_writel(tmp, clk->scale_reg);
- clk->rate = rate;
- return 0;
-}
-
-/*configure HCLK*/
-static int hclk_set_rate(struct clk *clk, u32 rate)
-{
- u32 tmp;
- tmp = __raw_readl(clk->scale_reg);
- tmp = tmp & ~0x3;
- switch (rate) {
- case 1:
- break;
- case 2:
- tmp |= 1;
- break;
- case 4:
- tmp |= 2;
- break;
- }
-
- __raw_writel(tmp, clk->scale_reg);
- clk->rate = rate;
- return 0;
-}
-
-static u32 hclk_round_rate(struct clk *clk, u32 rate)
-{
- switch (rate) {
- case 1:
- case 4:
- return rate;
- }
- return 2;
-}
-
-static u32 per_clk_round_rate(struct clk *clk, u32 rate)
-{
- return CLK_RATE_13MHZ;
-}
-
-static int on_off_set_rate(struct clk *clk, u32 rate)
-{
- if (rate) {
- clk_reg_enable(clk);
- clk->rate = 1;
- } else {
- clk_reg_disable(clk);
- clk->rate = 0;
- }
- return 0;
-}
-
-static int on_off_inv_set_rate(struct clk *clk, u32 rate)
-{
- if (rate) {
- clk_reg_disable(clk); /*enable bit is inverted */
- clk->rate = 1;
- } else {
- clk_reg_enable(clk);
- clk->rate = 0;
- }
- return 0;
-}
-
-static u32 on_off_round_rate(struct clk *clk, u32 rate)
-{
- return (rate ? 1 : 0);
-}
-
-static u32 pll4_round_rate(struct clk *clk, u32 rate)
-{
- if (rate > CLK_RATE_208MHZ)
- rate = CLK_RATE_208MHZ;
- if (rate == CLK_RATE_208MHZ && hclk_ck.user_rate == 1)
- rate = CLK_RATE_208MHZ - CLK_RATE_13MHZ;
- return (rate - (rate % (hclk_ck.user_rate * CLK_RATE_13MHZ)));
-}
-
-static u32 pll3_round_rate(struct clk *clk, u32 rate)
-{
- if (rate > CLK_RATE_208MHZ)
- rate = CLK_RATE_208MHZ;
- return (rate - rate % CLK_RATE_13MHZ);
-}
-
-static u32 pll5_round_rate(struct clk *clk, u32 rate)
-{
- return (rate ? CLK_RATE_48MHZ : 0);
-}
-
-static u32 ck_13MHz_round_rate(struct clk *clk, u32 rate)
-{
- return (rate ? CLK_RATE_13MHZ : 0);
-}
-
-static int ck_13MHz_set_rate(struct clk *clk, u32 rate)
-{
- if (rate) {
- clk_reg_disable(clk); /*enable bit is inverted */
- udelay(500);
- clk->rate = CLK_RATE_13MHZ;
- ck_1MHz.rate = CLK_RATE_1MHZ;
- } else {
- clk_reg_enable(clk);
- clk->rate = 0;
- ck_1MHz.rate = 0;
- }
- return 0;
-}
-
-static int pll1_set_rate(struct clk *clk, u32 rate)
-{
-#if 0 /* doesn't work on some boards, probably a HW BUG */
- if (rate) {
- clk_reg_disable(clk); /*enable bit is inverted */
- if (!clk_wait_for_pll_lock(clk)) {
- clk->rate = CLK_RATE_13MHZ;
- } else {
- clk_reg_enable(clk);
- clk->rate = 0;
- }
-
- } else {
- clk_reg_enable(clk);
- clk->rate = 0;
- }
-#endif
- return 0;
-}
-
-/* Clock sources */
-
-static struct clk osc_13MHz = {
- .name = "osc_13MHz",
- .flags = FIXED_RATE,
- .rate = CLK_RATE_13MHZ,
-};
-
-static struct clk ck_13MHz = {
- .name = "ck_13MHz",
- .parent = &osc_13MHz,
- .flags = NEEDS_INITIALIZATION,
- .round_rate = &ck_13MHz_round_rate,
- .set_rate = &ck_13MHz_set_rate,
- .enable_reg = OSC13CTRL_REG,
- .enable_shift = 0,
- .rate = CLK_RATE_13MHZ,
-};
-
-static struct clk osc_32KHz = {
- .name = "osc_32KHz",
- .flags = FIXED_RATE,
- .rate = CLK_RATE_32KHZ,
-};
-
-/*attached to PLL5*/
-static struct clk ck_1MHz = {
- .name = "ck_1MHz",
- .flags = FIXED_RATE | PARENT_SET_RATE,
- .parent = &ck_13MHz,
-};
-
-/* PLL1 (397) - provides 13' MHz clock */
-static struct clk ck_pll1 = {
- .name = "ck_pll1",
- .parent = &osc_32KHz,
- .flags = NEEDS_INITIALIZATION,
- .round_rate = &ck_13MHz_round_rate,
- .set_rate = &pll1_set_rate,
- .enable_reg = PLLCTRL_REG,
- .enable_shift = 1,
- .scale_reg = PLLCTRL_REG,
- .rate = CLK_RATE_13MHZ,
-};
-
-/* CPU/Bus PLL */
-static struct clk ck_pll4 = {
- .name = "ck_pll4",
- .parent = &ck_pll1,
- .flags = RATE_PROPAGATES | NEEDS_INITIALIZATION,
- .propagate_next = &per_ck,
- .round_rate = &pll4_round_rate,
- .set_rate = &pll160_set_rate,
- .rate = CLK_RATE_208MHZ,
- .scale_reg = HCLKPLLCTRL_REG,
- .enable_reg = PWRCTRL_REG,
- .enable_shift = 2,
- .parent_switch_reg = SYSCLKCTRL_REG,
- .set_parent = &set_13MHz_parent,
-};
-
-/* USB PLL */
-static struct clk ck_pll5 = {
- .name = "ck_pll5",
- .parent = &ck_1MHz,
- .flags = NEEDS_INITIALIZATION,
- .round_rate = &pll5_round_rate,
- .set_rate = &pll160_set_rate,
- .scale_reg = USBCTRL_REG,
- .enable_reg = USBCTRL_REG,
- .enable_shift = 18,
- .enable_reg1 = USBCTRL_REG,
- .enable_shift1 = 17,
-};
-
-/* XPERTTeak DSP PLL */
-static struct clk ck_pll3 = {
- .name = "ck_pll3",
- .parent = &ck_pll1,
- .flags = NEEDS_INITIALIZATION,
- .round_rate = &pll3_round_rate,
- .set_rate = &pll160_set_rate,
- .scale_reg = DSPPLLCTRL_REG,
- .enable_reg = DSPCLKCTRL_REG,
- .enable_shift = 3,
- .enable_reg1 = DSPCLKCTRL_REG,
- .enable_shift1 = 2,
- .parent_switch_reg = DSPCLKCTRL_REG,
- .set_parent = &set_13MHz_parent,
-};
-
-static struct clk hclk_ck = {
- .name = "hclk_ck",
- .parent = &ck_pll4,
- .flags = PARENT_SET_RATE,
- .set_rate = &hclk_set_rate,
- .round_rate = &hclk_round_rate,
- .scale_reg = HCLKDIVCTRL_REG,
- .rate = 2,
- .user_rate = 2,
-};
-
-static struct clk per_ck = {
- .name = "per_ck",
- .parent = &ck_pll4,
- .flags = FIXED_RATE,
- .propagate_next = &hclk_ck,
- .set_rate = &per_clk_set_rate,
- .round_rate = &per_clk_round_rate,
- .scale_reg = HCLKDIVCTRL_REG,
- .rate = CLK_RATE_13MHZ,
- .user_rate = CLK_RATE_13MHZ,
-};
-
-static struct clk m2hclk_ck = {
- .name = "m2hclk_ck",
- .parent = &hclk_ck,
- .flags = NEEDS_INITIALIZATION,
- .round_rate = &on_off_round_rate,
- .set_rate = &on_off_inv_set_rate,
- .rate = 1,
- .enable_shift = 6,
- .enable_reg = PWRCTRL_REG,
-};
-
-static struct clk vfp9_ck = {
- .name = "vfp9_ck",
- .parent = &ck_pll4,
- .flags = NEEDS_INITIALIZATION,
- .round_rate = &on_off_round_rate,
- .set_rate = &on_off_set_rate,
- .rate = 1,
- .enable_shift = 4,
- .enable_reg = VFP9CLKCTRL_REG,
-};
-
-static struct clk keyscan_ck = {
- .name = "keyscan_ck",
- .parent = &osc_32KHz,
- .flags = NEEDS_INITIALIZATION,
- .round_rate = &on_off_round_rate,
- .set_rate = &on_off_set_rate,
- .enable_shift = 0,
- .enable_reg = KEYCLKCTRL_REG,
-};
-
-static struct clk touch_ck = {
- .name = "touch_ck",
- .parent = &osc_32KHz,
- .flags = NEEDS_INITIALIZATION,
- .round_rate = &on_off_round_rate,
- .set_rate = &on_off_set_rate,
- .enable_shift = 0,
- .enable_reg = TSCLKCTRL_REG,
-};
-
-static struct clk pwm1_ck = {
- .name = "pwm1_ck",
- .parent = &osc_32KHz,
- .flags = NEEDS_INITIALIZATION,
- .round_rate = &on_off_round_rate,
- .set_rate = &on_off_set_rate,
- .enable_shift = 0,
- .enable_reg = PWMCLKCTRL_REG,
-};
-
-static struct clk pwm2_ck = {
- .name = "pwm2_ck",
- .parent = &osc_32KHz,
- .flags = NEEDS_INITIALIZATION,
- .round_rate = &on_off_round_rate,
- .set_rate = &on_off_set_rate,
- .enable_shift = 2,
- .enable_reg = PWMCLKCTRL_REG,
-};
-
-static struct clk jpeg_ck = {
- .name = "jpeg_ck",
- .parent = &hclk_ck,
- .flags = NEEDS_INITIALIZATION,
- .round_rate = &on_off_round_rate,
- .set_rate = &on_off_set_rate,
- .enable_shift = 0,
- .enable_reg = JPEGCLKCTRL_REG,
-};
-
-static struct clk ms_ck = {
- .name = "ms_ck",
- .parent = &ck_pll4,
- .flags = NEEDS_INITIALIZATION,
- .round_rate = &on_off_round_rate,
- .set_rate = &on_off_set_rate,
- .enable_shift = 5,
- .enable_reg = MSCTRL_REG,
-};
-
-static struct clk dum_ck = {
- .name = "dum_ck",
- .parent = &hclk_ck,
- .flags = NEEDS_INITIALIZATION,
- .round_rate = &on_off_round_rate,
- .set_rate = &on_off_set_rate,
- .enable_shift = 0,
- .enable_reg = DUMCLKCTRL_REG,
-};
-
-static struct clk flash_ck = {
- .name = "flash_ck",
- .parent = &hclk_ck,
- .round_rate = &on_off_round_rate,
- .set_rate = &on_off_set_rate,
- .enable_shift = 1, /* Only MLC clock supported */
- .enable_reg = FLASHCLKCTRL_REG,
-};
-
-static struct clk i2c0_ck = {
- .name = "i2c0_ck",
- .parent = &per_ck,
- .flags = NEEDS_INITIALIZATION | FIXED_RATE,
- .enable_shift = 0,
- .enable_reg = I2CCLKCTRL_REG,
- .rate = 13000000,
- .enable = clk_reg_enable,
- .disable = clk_reg_disable,
-};
-
-static struct clk i2c1_ck = {
- .name = "i2c1_ck",
- .parent = &per_ck,
- .flags = NEEDS_INITIALIZATION | FIXED_RATE,
- .enable_shift = 1,
- .enable_reg = I2CCLKCTRL_REG,
- .rate = 13000000,
- .enable = clk_reg_enable,
- .disable = clk_reg_disable,
-};
-
-static struct clk i2c2_ck = {
- .name = "i2c2_ck",
- .parent = &per_ck,
- .flags = NEEDS_INITIALIZATION | FIXED_RATE,
- .enable_shift = 2,
- .enable_reg = USB_OTG_CLKCTRL_REG,
- .rate = 13000000,
- .enable = clk_reg_enable,
- .disable = clk_reg_disable,
-};
-
-static struct clk spi0_ck = {
- .name = "spi0_ck",
- .parent = &hclk_ck,
- .flags = NEEDS_INITIALIZATION,
- .round_rate = &on_off_round_rate,
- .set_rate = &on_off_set_rate,
- .enable_shift = 0,
- .enable_reg = SPICTRL_REG,
-};
-
-static struct clk spi1_ck = {
- .name = "spi1_ck",
- .parent = &hclk_ck,
- .flags = NEEDS_INITIALIZATION,
- .round_rate = &on_off_round_rate,
- .set_rate = &on_off_set_rate,
- .enable_shift = 4,
- .enable_reg = SPICTRL_REG,
-};
-
-static struct clk dma_ck = {
- .name = "dma_ck",
- .parent = &hclk_ck,
- .round_rate = &on_off_round_rate,
- .set_rate = &on_off_set_rate,
- .enable_shift = 0,
- .enable_reg = DMACLKCTRL_REG,
-};
-
-static struct clk uart3_ck = {
- .name = "uart3_ck",
- .parent = &per_ck,
- .flags = NEEDS_INITIALIZATION,
- .round_rate = &on_off_round_rate,
- .set_rate = &on_off_set_rate,
- .rate = 1,
- .enable_shift = 0,
- .enable_reg = UARTCLKCTRL_REG,
-};
-
-static struct clk uart4_ck = {
- .name = "uart4_ck",
- .parent = &per_ck,
- .flags = NEEDS_INITIALIZATION,
- .round_rate = &on_off_round_rate,
- .set_rate = &on_off_set_rate,
- .enable_shift = 1,
- .enable_reg = UARTCLKCTRL_REG,
-};
-
-static struct clk uart5_ck = {
- .name = "uart5_ck",
- .parent = &per_ck,
- .flags = NEEDS_INITIALIZATION,
- .round_rate = &on_off_round_rate,
- .set_rate = &on_off_set_rate,
- .rate = 1,
- .enable_shift = 2,
- .enable_reg = UARTCLKCTRL_REG,
-};
-
-static struct clk uart6_ck = {
- .name = "uart6_ck",
- .parent = &per_ck,
- .flags = NEEDS_INITIALIZATION,
- .round_rate = &on_off_round_rate,
- .set_rate = &on_off_set_rate,
- .enable_shift = 3,
- .enable_reg = UARTCLKCTRL_REG,
-};
-
-static struct clk wdt_ck = {
- .name = "wdt_ck",
- .parent = &per_ck,
- .flags = NEEDS_INITIALIZATION,
- .enable_shift = 0,
- .enable_reg = TIMCLKCTRL_REG,
- .enable = clk_reg_enable,
- .disable = clk_reg_disable,
-};
-
-/* These clocks are visible outside this module
- * and can be initialized
- */
-static struct clk *onchip_clks[] __initdata = {
- &ck_13MHz,
- &ck_pll1,
- &ck_pll4,
- &ck_pll5,
- &ck_pll3,
- &vfp9_ck,
- &m2hclk_ck,
- &hclk_ck,
- &dma_ck,
- &flash_ck,
- &dum_ck,
- &keyscan_ck,
- &pwm1_ck,
- &pwm2_ck,
- &jpeg_ck,
- &ms_ck,
- &touch_ck,
- &i2c0_ck,
- &i2c1_ck,
- &i2c2_ck,
- &spi0_ck,
- &spi1_ck,
- &uart3_ck,
- &uart4_ck,
- &uart5_ck,
- &uart6_ck,
- &wdt_ck,
-};
-
-static struct clk_lookup onchip_clkreg[] = {
- { .clk = &ck_13MHz, .con_id = "ck_13MHz" },
- { .clk = &ck_pll1, .con_id = "ck_pll1" },
- { .clk = &ck_pll4, .con_id = "ck_pll4" },
- { .clk = &ck_pll5, .con_id = "ck_pll5" },
- { .clk = &ck_pll3, .con_id = "ck_pll3" },
- { .clk = &vfp9_ck, .con_id = "vfp9_ck" },
- { .clk = &m2hclk_ck, .con_id = "m2hclk_ck" },
- { .clk = &hclk_ck, .con_id = "hclk_ck" },
- { .clk = &dma_ck, .con_id = "dma_ck" },
- { .clk = &flash_ck, .con_id = "flash_ck" },
- { .clk = &dum_ck, .con_id = "dum_ck" },
- { .clk = &keyscan_ck, .con_id = "keyscan_ck" },
- { .clk = &pwm1_ck, .con_id = "pwm1_ck" },
- { .clk = &pwm2_ck, .con_id = "pwm2_ck" },
- { .clk = &jpeg_ck, .con_id = "jpeg_ck" },
- { .clk = &ms_ck, .con_id = "ms_ck" },
- { .clk = &touch_ck, .con_id = "touch_ck" },
- { .clk = &i2c0_ck, .dev_id = "pnx-i2c.0" },
- { .clk = &i2c1_ck, .dev_id = "pnx-i2c.1" },
- { .clk = &i2c2_ck, .dev_id = "pnx-i2c.2" },
- { .clk = &spi0_ck, .con_id = "spi0_ck" },
- { .clk = &spi1_ck, .con_id = "spi1_ck" },
- { .clk = &uart3_ck, .con_id = "uart3_ck" },
- { .clk = &uart4_ck, .con_id = "uart4_ck" },
- { .clk = &uart5_ck, .con_id = "uart5_ck" },
- { .clk = &uart6_ck, .con_id = "uart6_ck" },
- { .clk = &wdt_ck, .dev_id = "pnx4008-watchdog" },
-};
-
-static void local_clk_disable(struct clk *clk)
-{
- if (WARN_ON(clk->usecount == 0))
- return;
-
- if (!(--clk->usecount)) {
- if (clk->disable)
- clk->disable(clk);
- else if (!(clk->flags & FIXED_RATE) && clk->rate && clk->set_rate)
- clk->set_rate(clk, 0);
- if (clk->parent)
- local_clk_disable(clk->parent);
- }
-}
-
-static int local_clk_enable(struct clk *clk)
-{
- int ret = 0;
-
- if (clk->usecount == 0) {
- if (clk->parent) {
- ret = local_clk_enable(clk->parent);
- if (ret != 0)
- goto out;
- }
-
- if (clk->enable)
- ret = clk->enable(clk);
- else if (!(clk->flags & FIXED_RATE) && !clk->rate && clk->set_rate
- && clk->user_rate)
- ret = clk->set_rate(clk, clk->user_rate);
-
- if (ret != 0 && clk->parent) {
- local_clk_disable(clk->parent);
- goto out;
- }
-
- clk->usecount++;
- }
-out:
- return ret;
-}
-
-static int local_set_rate(struct clk *clk, u32 rate)
-{
- int ret = -EINVAL;
- if (clk->set_rate) {
-
- if (clk->user_rate == clk->rate && clk->parent->rate) {
- /* if clock enabled or rate not set */
- clk->user_rate = clk->round_rate(clk, rate);
- ret = clk->set_rate(clk, clk->user_rate);
- } else
- clk->user_rate = clk->round_rate(clk, rate);
- ret = 0;
- }
- return ret;
-}
-
-int clk_set_rate(struct clk *clk, unsigned long rate)
-{
- int ret = -EINVAL;
-
- if (clk->flags & FIXED_RATE)
- goto out;
-
- clock_lock();
- if ((clk->flags & PARENT_SET_RATE) && clk->parent) {
-
- clk->user_rate = clk->round_rate(clk, rate);
- /* parent clock needs to be refreshed
- for the setting to take effect */
- } else {
- ret = local_set_rate(clk, rate);
- }
- ret = 0;
- clock_unlock();
-
-out:
- return ret;
-}
-
-EXPORT_SYMBOL(clk_set_rate);
-
-unsigned long clk_get_rate(struct clk *clk)
-{
- unsigned long ret;
- clock_lock();
- ret = clk->rate;
- clock_unlock();
- return ret;
-}
-EXPORT_SYMBOL(clk_get_rate);
-
-int clk_enable(struct clk *clk)
-{
- int ret;
-
- clock_lock();
- ret = local_clk_enable(clk);
- clock_unlock();
- return ret;
-}
-
-EXPORT_SYMBOL(clk_enable);
-
-void clk_disable(struct clk *clk)
-{
- clock_lock();
- local_clk_disable(clk);
- clock_unlock();
-}
-
-EXPORT_SYMBOL(clk_disable);
-
-long clk_round_rate(struct clk *clk, unsigned long rate)
-{
- long ret;
- clock_lock();
- if (clk->round_rate)
- ret = clk->round_rate(clk, rate);
- else
- ret = clk->rate;
- clock_unlock();
- return ret;
-}
-
-EXPORT_SYMBOL(clk_round_rate);
-
-int clk_set_parent(struct clk *clk, struct clk *parent)
-{
- int ret = -ENODEV;
- if (!clk->set_parent)
- goto out;
-
- clock_lock();
- ret = clk->set_parent(clk, parent);
- if (!ret)
- clk->parent = parent;
- clock_unlock();
-
-out:
- return ret;
-}
-
-EXPORT_SYMBOL(clk_set_parent);
-
-static int __init clk_init(void)
-{
- struct clk **clkp;
-
- /* Disable autoclocking, as it doesn't seem to work */
- __raw_writel(0xff, AUTOCLK_CTRL);
-
- for (clkp = onchip_clks; clkp < onchip_clks + ARRAY_SIZE(onchip_clks);
- clkp++) {
- struct clk *clk = *clkp;
- if (clk->flags & NEEDS_INITIALIZATION) {
- if (clk->set_rate) {
- clk->user_rate = clk->rate;
- local_set_rate(clk, clk->user_rate);
- if (clk->set_parent)
- clk->set_parent(clk, clk->parent);
- }
- if (clk->enable && clk->usecount)
- clk->enable(clk);
- if (clk->disable && !clk->usecount)
- clk->disable(clk);
- }
- pr_debug("%s: clock %s, rate %ld\n",
- __func__, clk->name, clk->rate);
- }
-
- local_clk_enable(&ck_pll4);
-
- /* if ck_13MHz is not used, disable it. */
- if (ck_13MHz.usecount == 0)
- local_clk_disable(&ck_13MHz);
-
- /* Disable autoclocking */
- __raw_writeb(0xff, AUTOCLK_CTRL);
-
- clkdev_add_table(onchip_clkreg, ARRAY_SIZE(onchip_clkreg));
-
- return 0;
-}
-
-arch_initcall(clk_init);
@@ -1,43 +0,0 @@
-/*
- * arch/arm/mach-pnx4008/clock.h
- *
- * Clock control driver for PNX4008 - internal header file
- *
- * Author: Vitaly Wool <source@mvista.com>
- *
- * 2006 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-#ifndef __ARCH_ARM_PNX4008_CLOCK_H__
-#define __ARCH_ARM_PNX4008_CLOCK_H__
-
-struct clk {
- const char *name;
- struct clk *parent;
- struct clk *propagate_next;
- u32 rate;
- u32 user_rate;
- s8 usecount;
- u32 flags;
- u32 scale_reg;
- u8 enable_shift;
- u32 enable_reg;
- u8 enable_shift1;
- u32 enable_reg1;
- u32 parent_switch_reg;
- u32(*round_rate) (struct clk *, u32);
- int (*set_rate) (struct clk *, u32);
- int (*set_parent) (struct clk * clk, struct clk * parent);
- int (*enable)(struct clk *);
- void (*disable)(struct clk *);
-};
-
-/* Flags */
-#define RATE_PROPAGATES (1<<0)
-#define NEEDS_INITIALIZATION (1<<1)
-#define PARENT_SET_RATE (1<<2)
-#define FIXED_RATE (1<<3)
-
-#endif
@@ -1,290 +0,0 @@
-/*
- * arch/arm/mach-pnx4008/core.c
- *
- * PNX4008 core startup code
- *
- * Authors: Vitaly Wool, Dmitry Chigirev,
- * Grigory Tolstolytkin, Dmitry Pervushin <source@mvista.com>
- *
- * Based on reference code received from Philips:
- * Copyright (C) 2003 Philips Semiconductors
- *
- * 2005 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/mm.h>
-#include <linux/interrupt.h>
-#include <linux/list.h>
-#include <linux/init.h>
-#include <linux/ioport.h>
-#include <linux/serial_8250.h>
-#include <linux/device.h>
-#include <linux/spi/spi.h>
-#include <linux/io.h>
-
-#include <mach/hardware.h>
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/pgtable.h>
-#include <asm/page.h>
-#include <asm/system_misc.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/time.h>
-
-#include <mach/irq.h>
-#include <mach/clock.h>
-#include <mach/dma.h>
-
-struct resource spipnx_0_resources[] = {
- {
- .start = PNX4008_SPI1_BASE,
- .end = PNX4008_SPI1_BASE + SZ_4K,
- .flags = IORESOURCE_MEM,
- }, {
- .start = PER_SPI1_REC_XMIT,
- .flags = IORESOURCE_DMA,
- }, {
- .start = SPI1_INT,
- .flags = IORESOURCE_IRQ,
- }, {
- .flags = 0,
- },
-};
-
-struct resource spipnx_1_resources[] = {
- {
- .start = PNX4008_SPI2_BASE,
- .end = PNX4008_SPI2_BASE + SZ_4K,
- .flags = IORESOURCE_MEM,
- }, {
- .start = PER_SPI2_REC_XMIT,
- .flags = IORESOURCE_DMA,
- }, {
- .start = SPI2_INT,
- .flags = IORESOURCE_IRQ,
- }, {
- .flags = 0,
- }
-};
-
-static struct spi_board_info spi_board_info[] __initdata = {
- {
- .modalias = "m25p80",
- .max_speed_hz = 1000000,
- .bus_num = 1,
- .chip_select = 0,
- },
-};
-
-static struct platform_device spipnx_1 = {
- .name = "spipnx",
- .id = 1,
- .num_resources = ARRAY_SIZE(spipnx_0_resources),
- .resource = spipnx_0_resources,
- .dev = {
- .coherent_dma_mask = 0xFFFFFFFF,
- },
-};
-
-static struct platform_device spipnx_2 = {
- .name = "spipnx",
- .id = 2,
- .num_resources = ARRAY_SIZE(spipnx_1_resources),
- .resource = spipnx_1_resources,
- .dev = {
- .coherent_dma_mask = 0xFFFFFFFF,
- },
-};
-
-static struct plat_serial8250_port platform_serial_ports[] = {
- {
- .membase = (void *)__iomem(IO_ADDRESS(PNX4008_UART5_BASE)),
- .mapbase = (unsigned long)PNX4008_UART5_BASE,
- .irq = IIR5_INT,
- .uartclk = PNX4008_UART_CLK,
- .regshift = 2,
- .iotype = UPIO_MEM,
- .flags = UPF_BOOT_AUTOCONF | UPF_BUGGY_UART | UPF_SKIP_TEST,
- },
- {
- .membase = (void *)__iomem(IO_ADDRESS(PNX4008_UART3_BASE)),
- .mapbase = (unsigned long)PNX4008_UART3_BASE,
- .irq = IIR3_INT,
- .uartclk = PNX4008_UART_CLK,
- .regshift = 2,
- .iotype = UPIO_MEM,
- .flags = UPF_BOOT_AUTOCONF | UPF_BUGGY_UART | UPF_SKIP_TEST,
- },
- {}
-};
-
-static struct platform_device serial_device = {
- .name = "serial8250",
- .id = PLAT8250_DEV_PLATFORM,
- .dev = {
- .platform_data = &platform_serial_ports,
- },
-};
-
-static struct platform_device nand_flash_device = {
- .name = "pnx4008-flash",
- .id = -1,
- .dev = {
- .coherent_dma_mask = 0xFFFFFFFF,
- },
-};
-
-/* The dmamask must be set for OHCI to work */
-static u64 ohci_dmamask = ~(u32) 0;
-
-static struct resource ohci_resources[] = {
- {
- .start = IO_ADDRESS(PNX4008_USB_CONFIG_BASE),
- .end = IO_ADDRESS(PNX4008_USB_CONFIG_BASE + 0x100),
- .flags = IORESOURCE_MEM,
- }, {
- .start = USB_HOST_INT,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device ohci_device = {
- .name = "pnx4008-usb-ohci",
- .id = -1,
- .dev = {
- .dma_mask = &ohci_dmamask,
- .coherent_dma_mask = 0xffffffff,
- },
- .num_resources = ARRAY_SIZE(ohci_resources),
- .resource = ohci_resources,
-};
-
-static struct platform_device sdum_device = {
- .name = "pnx4008-sdum",
- .id = 0,
- .dev = {
- .coherent_dma_mask = 0xffffffff,
- },
-};
-
-static struct platform_device rgbfb_device = {
- .name = "pnx4008-rgbfb",
- .id = 0,
- .dev = {
- .coherent_dma_mask = 0xffffffff,
- }
-};
-
-struct resource watchdog_resources[] = {
- {
- .start = PNX4008_WDOG_BASE,
- .end = PNX4008_WDOG_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct platform_device watchdog_device = {
- .name = "pnx4008-watchdog",
- .id = -1,
- .num_resources = ARRAY_SIZE(watchdog_resources),
- .resource = watchdog_resources,
-};
-
-static struct platform_device *devices[] __initdata = {
- &spipnx_1,
- &spipnx_2,
- &serial_device,
- &ohci_device,
- &nand_flash_device,
- &sdum_device,
- &rgbfb_device,
- &watchdog_device,
-};
-
-
-extern void pnx4008_uart_init(void);
-
-static void __init pnx4008_init(void)
-{
- /*disable all START interrupt sources,
- and clear all START interrupt flags */
- __raw_writel(0, START_INT_ER_REG(SE_PIN_BASE_INT));
- __raw_writel(0, START_INT_ER_REG(SE_INT_BASE_INT));
- __raw_writel(0xffffffff, START_INT_RSR_REG(SE_PIN_BASE_INT));
- __raw_writel(0xffffffff, START_INT_RSR_REG(SE_INT_BASE_INT));
-
- platform_add_devices(devices, ARRAY_SIZE(devices));
- spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
- /* Switch on the UART clocks */
- pnx4008_uart_init();
-}
-
-static struct map_desc pnx4008_io_desc[] __initdata = {
- {
- .virtual = IO_ADDRESS(PNX4008_IRAM_BASE),
- .pfn = __phys_to_pfn(PNX4008_IRAM_BASE),
- .length = SZ_64K,
- .type = MT_DEVICE,
- }, {
- .virtual = IO_ADDRESS(PNX4008_NDF_FLASH_BASE),
- .pfn = __phys_to_pfn(PNX4008_NDF_FLASH_BASE),
- .length = SZ_1M - SZ_128K,
- .type = MT_DEVICE,
- }, {
- .virtual = IO_ADDRESS(PNX4008_JPEG_CONFIG_BASE),
- .pfn = __phys_to_pfn(PNX4008_JPEG_CONFIG_BASE),
- .length = SZ_128K * 3,
- .type = MT_DEVICE,
- }, {
- .virtual = IO_ADDRESS(PNX4008_DMA_CONFIG_BASE),
- .pfn = __phys_to_pfn(PNX4008_DMA_CONFIG_BASE),
- .length = SZ_1M,
- .type = MT_DEVICE,
- }, {
- .virtual = IO_ADDRESS(PNX4008_AHB2FAB_BASE),
- .pfn = __phys_to_pfn(PNX4008_AHB2FAB_BASE),
- .length = SZ_1M,
- .type = MT_DEVICE,
- },
-};
-
-void __init pnx4008_map_io(void)
-{
- iotable_init(pnx4008_io_desc, ARRAY_SIZE(pnx4008_io_desc));
-}
-
-static void pnx4008_restart(char mode, const char *cmd)
-{
- soft_restart(0);
-}
-
-#ifdef CONFIG_PM
-extern int pnx4008_pm_init(void);
-#else
-static inline int pnx4008_pm_init(void) { return 0; }
-#endif
-
-void __init pnx4008_init_late(void)
-{
- pnx4008_pm_init();
-}
-
-extern struct sys_timer pnx4008_timer;
-
-MACHINE_START(PNX4008, "Philips PNX4008")
- /* Maintainer: MontaVista Software Inc. */
- .atag_offset = 0x100,
- .map_io = pnx4008_map_io,
- .init_irq = pnx4008_init_irq,
- .init_machine = pnx4008_init,
- .init_late = pnx4008_init_late,
- .timer = &pnx4008_timer,
- .restart = pnx4008_restart,
-MACHINE_END
@@ -1,1105 +0,0 @@
-/*
- * linux/arch/arm/mach-pnx4008/dma.c
- *
- * PNX4008 DMA registration and IRQ dispatching
- *
- * Author: Vitaly Wool
- * Copyright: MontaVista Software Inc. (c) 2005
- *
- * Based on the code from Nicolas Pitre
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/interrupt.h>
-#include <linux/errno.h>
-#include <linux/err.h>
-#include <linux/dma-mapping.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/gfp.h>
-
-#include <mach/hardware.h>
-#include <mach/dma.h>
-#include <asm/dma-mapping.h>
-#include <mach/clock.h>
-
-static struct dma_channel {
- char *name;
- void (*irq_handler) (int, int, void *);
- void *data;
- struct pnx4008_dma_ll *ll;
- u32 ll_dma;
- void *target_addr;
- int target_id;
-} dma_channels[MAX_DMA_CHANNELS];
-
-static struct ll_pool {
- void *vaddr;
- void *cur;
- dma_addr_t dma_addr;
- int count;
-} ll_pool;
-
-static DEFINE_SPINLOCK(ll_lock);
-
-struct pnx4008_dma_ll *pnx4008_alloc_ll_entry(dma_addr_t * ll_dma)
-{
- struct pnx4008_dma_ll *ll = NULL;
- unsigned long flags;
-
- spin_lock_irqsave(&ll_lock, flags);
- if (ll_pool.count > 4) { /* can give one more */
- ll = *(struct pnx4008_dma_ll **) ll_pool.cur;
- *ll_dma = ll_pool.dma_addr + ((void *)ll - ll_pool.vaddr);
- *(void **)ll_pool.cur = **(void ***)ll_pool.cur;
- memset(ll, 0, sizeof(*ll));
- ll_pool.count--;
- }
- spin_unlock_irqrestore(&ll_lock, flags);
-
- return ll;
-}
-
-EXPORT_SYMBOL_GPL(pnx4008_alloc_ll_entry);
-
-void pnx4008_free_ll_entry(struct pnx4008_dma_ll * ll, dma_addr_t ll_dma)
-{
- unsigned long flags;
-
- if (ll) {
- if ((unsigned long)((long)ll - (long)ll_pool.vaddr) > 0x4000) {
- printk(KERN_ERR "Trying to free entry not allocated by DMA\n");
- BUG();
- }
-
- if (ll->flags & DMA_BUFFER_ALLOCATED)
- ll->free(ll->alloc_data);
-
- spin_lock_irqsave(&ll_lock, flags);
- *(long *)ll = *(long *)ll_pool.cur;
- *(long *)ll_pool.cur = (long)ll;
- ll_pool.count++;
- spin_unlock_irqrestore(&ll_lock, flags);
- }
-}
-
-EXPORT_SYMBOL_GPL(pnx4008_free_ll_entry);
-
-void pnx4008_free_ll(u32 ll_dma, struct pnx4008_dma_ll * ll)
-{
- struct pnx4008_dma_ll *ptr;
- u32 dma;
-
- while (ll) {
- dma = ll->next_dma;
- ptr = ll->next;
- pnx4008_free_ll_entry(ll, ll_dma);
-
- ll_dma = dma;
- ll = ptr;
- }
-}
-
-EXPORT_SYMBOL_GPL(pnx4008_free_ll);
-
-static int dma_channels_requested = 0;
-
-static inline void dma_increment_usage(void)
-{
- if (!dma_channels_requested++) {
- struct clk *clk = clk_get(0, "dma_ck");
- if (!IS_ERR(clk)) {
- clk_set_rate(clk, 1);
- clk_put(clk);
- }
- pnx4008_config_dma(-1, -1, 1);
- }
-}
-static inline void dma_decrement_usage(void)
-{
- if (!--dma_channels_requested) {
- struct clk *clk = clk_get(0, "dma_ck");
- if (!IS_ERR(clk)) {
- clk_set_rate(clk, 0);
- clk_put(clk);
- }
- pnx4008_config_dma(-1, -1, 0);
-
- }
-}
-
-static DEFINE_SPINLOCK(dma_lock);
-
-static inline void pnx4008_dma_lock(void)
-{
- spin_lock_irq(&dma_lock);
-}
-
-static inline void pnx4008_dma_unlock(void)
-{
- spin_unlock_irq(&dma_lock);
-}
-
-#define VALID_CHANNEL(c) (((c) >= 0) && ((c) < MAX_DMA_CHANNELS))
-
-int pnx4008_request_channel(char *name, int ch,
- void (*irq_handler) (int, int, void *), void *data)
-{
- int i, found = 0;
-
- /* basic sanity checks */
- if (!name || (ch != -1 && !VALID_CHANNEL(ch)))
- return -EINVAL;
-
- pnx4008_dma_lock();
-
- /* try grabbing a DMA channel with the requested priority */
- for (i = MAX_DMA_CHANNELS - 1; i >= 0; i--) {
- if (!dma_channels[i].name && (ch == -1 || ch == i)) {
- found = 1;
- break;
- }
- }
-
- if (found) {
- dma_increment_usage();
- dma_channels[i].name = name;
- dma_channels[i].irq_handler = irq_handler;
- dma_channels[i].data = data;
- dma_channels[i].ll = NULL;
- dma_channels[i].ll_dma = 0;
- } else {
- printk(KERN_WARNING "No more available DMA channels for %s\n",
- name);
- i = -ENODEV;
- }
-
- pnx4008_dma_unlock();
- return i;
-}
-
-EXPORT_SYMBOL_GPL(pnx4008_request_channel);
-
-void pnx4008_free_channel(int ch)
-{
- if (!dma_channels[ch].name) {
- printk(KERN_CRIT
- "%s: trying to free channel %d which is already freed\n",
- __func__, ch);
- return;
- }
-
- pnx4008_dma_lock();
- pnx4008_free_ll(dma_channels[ch].ll_dma, dma_channels[ch].ll);
- dma_channels[ch].ll = NULL;
- dma_decrement_usage();
-
- dma_channels[ch].name = NULL;
- pnx4008_dma_unlock();
-}
-
-EXPORT_SYMBOL_GPL(pnx4008_free_channel);
-
-int pnx4008_config_dma(int ahb_m1_be, int ahb_m2_be, int enable)
-{
- unsigned long dma_cfg = __raw_readl(DMAC_CONFIG);
-
- switch (ahb_m1_be) {
- case 0:
- dma_cfg &= ~(1 << 1);
- break;
- case 1:
- dma_cfg |= (1 << 1);
- break;
- default:
- break;
- }
-
- switch (ahb_m2_be) {
- case 0:
- dma_cfg &= ~(1 << 2);
- break;
- case 1:
- dma_cfg |= (1 << 2);
- break;
- default:
- break;
- }
-
- switch (enable) {
- case 0:
- dma_cfg &= ~(1 << 0);
- break;
- case 1:
- dma_cfg |= (1 << 0);
- break;
- default:
- break;
- }
-
- pnx4008_dma_lock();
- __raw_writel(dma_cfg, DMAC_CONFIG);
- pnx4008_dma_unlock();
-
- return 0;
-}
-
-EXPORT_SYMBOL_GPL(pnx4008_config_dma);
-
-int pnx4008_dma_pack_control(const struct pnx4008_dma_ch_ctrl * ch_ctrl,
- unsigned long *ctrl)
-{
- int i = 0, dbsize, sbsize, err = 0;
-
- if (!ctrl || !ch_ctrl) {
- err = -EINVAL;
- goto out;
- }
-
- *ctrl = 0;
-
- switch (ch_ctrl->tc_mask) {
- case 0:
- break;
- case 1:
- *ctrl |= (1 << 31);
- break;
-
- default:
- err = -EINVAL;
- goto out;
- }
-
- switch (ch_ctrl->cacheable) {
- case 0:
- break;
- case 1:
- *ctrl |= (1 << 30);
- break;
-
- default:
- err = -EINVAL;
- goto out;
- }
- switch (ch_ctrl->bufferable) {
- case 0:
- break;
- case 1:
- *ctrl |= (1 << 29);
- break;
-
- default:
- err = -EINVAL;
- goto out;
- }
- switch (ch_ctrl->priv_mode) {
- case 0:
- break;
- case 1:
- *ctrl |= (1 << 28);
- break;
-
- default:
- err = -EINVAL;
- goto out;
- }
- switch (ch_ctrl->di) {
- case 0:
- break;
- case 1:
- *ctrl |= (1 << 27);
- break;
-
- default:
- err = -EINVAL;
- goto out;
- }
- switch (ch_ctrl->si) {
- case 0:
- break;
- case 1:
- *ctrl |= (1 << 26);
- break;
-
- default:
- err = -EINVAL;
- goto out;
- }
- switch (ch_ctrl->dest_ahb1) {
- case 0:
- break;
- case 1:
- *ctrl |= (1 << 25);
- break;
-
- default:
- err = -EINVAL;
- goto out;
- }
- switch (ch_ctrl->src_ahb1) {
- case 0:
- break;
- case 1:
- *ctrl |= (1 << 24);
- break;
-
- default:
- err = -EINVAL;
- goto out;
- }
- switch (ch_ctrl->dwidth) {
- case WIDTH_BYTE:
- *ctrl &= ~(7 << 21);
- break;
- case WIDTH_HWORD:
- *ctrl &= ~(7 << 21);
- *ctrl |= (1 << 21);
- break;
- case WIDTH_WORD:
- *ctrl &= ~(7 << 21);
- *ctrl |= (2 << 21);
- break;
-
- default:
- err = -EINVAL;
- goto out;
- }
- switch (ch_ctrl->swidth) {
- case WIDTH_BYTE:
- *ctrl &= ~(7 << 18);
- break;
- case WIDTH_HWORD:
- *ctrl &= ~(7 << 18);
- *ctrl |= (1 << 18);
- break;
- case WIDTH_WORD:
- *ctrl &= ~(7 << 18);
- *ctrl |= (2 << 18);
- break;
-
- default:
- err = -EINVAL;
- goto out;
- }
- dbsize = ch_ctrl->dbsize;
- while (!(dbsize & 1)) {
- i++;
- dbsize >>= 1;
- }
- if (ch_ctrl->dbsize != 1 || i > 8 || i == 1) {
- err = -EINVAL;
- goto out;
- } else if (i > 1)
- i--;
- *ctrl &= ~(7 << 15);
- *ctrl |= (i << 15);
-
- sbsize = ch_ctrl->sbsize;
- while (!(sbsize & 1)) {
- i++;
- sbsize >>= 1;
- }
- if (ch_ctrl->sbsize != 1 || i > 8 || i == 1) {
- err = -EINVAL;
- goto out;
- } else if (i > 1)
- i--;
- *ctrl &= ~(7 << 12);
- *ctrl |= (i << 12);
-
- if (ch_ctrl->tr_size > 0x7ff) {
- err = -E2BIG;
- goto out;
- }
- *ctrl &= ~0x7ff;
- *ctrl |= ch_ctrl->tr_size & 0x7ff;
-
-out:
- return err;
-}
-
-EXPORT_SYMBOL_GPL(pnx4008_dma_pack_control);
-
-int pnx4008_dma_parse_control(unsigned long ctrl,
- struct pnx4008_dma_ch_ctrl * ch_ctrl)
-{
- int err = 0;
-
- if (!ch_ctrl) {
- err = -EINVAL;
- goto out;
- }
-
- ch_ctrl->tr_size = ctrl & 0x7ff;
- ctrl >>= 12;
-
- ch_ctrl->sbsize = 1 << (ctrl & 7);
- if (ch_ctrl->sbsize > 1)
- ch_ctrl->sbsize <<= 1;
- ctrl >>= 3;
-
- ch_ctrl->dbsize = 1 << (ctrl & 7);
- if (ch_ctrl->dbsize > 1)
- ch_ctrl->dbsize <<= 1;
- ctrl >>= 3;
-
- switch (ctrl & 7) {
- case 0:
- ch_ctrl->swidth = WIDTH_BYTE;
- break;
- case 1:
- ch_ctrl->swidth = WIDTH_HWORD;
- break;
- case 2:
- ch_ctrl->swidth = WIDTH_WORD;
- break;
- default:
- err = -EINVAL;
- goto out;
- }
- ctrl >>= 3;
-
- switch (ctrl & 7) {
- case 0:
- ch_ctrl->dwidth = WIDTH_BYTE;
- break;
- case 1:
- ch_ctrl->dwidth = WIDTH_HWORD;
- break;
- case 2:
- ch_ctrl->dwidth = WIDTH_WORD;
- break;
- default:
- err = -EINVAL;
- goto out;
- }
- ctrl >>= 3;
-
- ch_ctrl->src_ahb1 = ctrl & 1;
- ctrl >>= 1;
-
- ch_ctrl->dest_ahb1 = ctrl & 1;
- ctrl >>= 1;
-
- ch_ctrl->si = ctrl & 1;
- ctrl >>= 1;
-
- ch_ctrl->di = ctrl & 1;
- ctrl >>= 1;
-
- ch_ctrl->priv_mode = ctrl & 1;
- ctrl >>= 1;
-
- ch_ctrl->bufferable = ctrl & 1;
- ctrl >>= 1;
-
- ch_ctrl->cacheable = ctrl & 1;
- ctrl >>= 1;
-
- ch_ctrl->tc_mask = ctrl & 1;
-
-out:
- return err;
-}
-
-EXPORT_SYMBOL_GPL(pnx4008_dma_parse_control);
-
-int pnx4008_dma_pack_config(const struct pnx4008_dma_ch_config * ch_cfg,
- unsigned long *cfg)
-{
- int err = 0;
-
- if (!cfg || !ch_cfg) {
- err = -EINVAL;
- goto out;
- }
-
- *cfg = 0;
-
- switch (ch_cfg->halt) {
- case 0:
- break;
- case 1:
- *cfg |= (1 << 18);
- break;
-
- default:
- err = -EINVAL;
- goto out;
- }
- switch (ch_cfg->active) {
- case 0:
- break;
- case 1:
- *cfg |= (1 << 17);
- break;
-
- default:
- err = -EINVAL;
- goto out;
- }
- switch (ch_cfg->lock) {
- case 0:
- break;
- case 1:
- *cfg |= (1 << 16);
- break;
-
- default:
- err = -EINVAL;
- goto out;
- }
- switch (ch_cfg->itc) {
- case 0:
- break;
- case 1:
- *cfg |= (1 << 15);
- break;
-
- default:
- err = -EINVAL;
- goto out;
- }
- switch (ch_cfg->ie) {
- case 0:
- break;
- case 1:
- *cfg |= (1 << 14);
- break;
-
- default:
- err = -EINVAL;
- goto out;
- }
- switch (ch_cfg->flow_cntrl) {
- case FC_MEM2MEM_DMA:
- *cfg &= ~(7 << 11);
- break;
- case FC_MEM2PER_DMA:
- *cfg &= ~(7 << 11);
- *cfg |= (1 << 11);
- break;
- case FC_PER2MEM_DMA:
- *cfg &= ~(7 << 11);
- *cfg |= (2 << 11);
- break;
- case FC_PER2PER_DMA:
- *cfg &= ~(7 << 11);
- *cfg |= (3 << 11);
- break;
- case FC_PER2PER_DPER:
- *cfg &= ~(7 << 11);
- *cfg |= (4 << 11);
- break;
- case FC_MEM2PER_PER:
- *cfg &= ~(7 << 11);
- *cfg |= (5 << 11);
- break;
- case FC_PER2MEM_PER:
- *cfg &= ~(7 << 11);
- *cfg |= (6 << 11);
- break;
- case FC_PER2PER_SPER:
- *cfg |= (7 << 11);
- break;
-
- default:
- err = -EINVAL;
- goto out;
- }
- *cfg &= ~(0x1f << 6);
- *cfg |= ((ch_cfg->dest_per & 0x1f) << 6);
-
- *cfg &= ~(0x1f << 1);
- *cfg |= ((ch_cfg->src_per & 0x1f) << 1);
-
-out:
- return err;
-}
-
-EXPORT_SYMBOL_GPL(pnx4008_dma_pack_config);
-
-int pnx4008_dma_parse_config(unsigned long cfg,
- struct pnx4008_dma_ch_config * ch_cfg)
-{
- int err = 0;
-
- if (!ch_cfg) {
- err = -EINVAL;
- goto out;
- }
-
- cfg >>= 1;
-
- ch_cfg->src_per = cfg & 0x1f;
- cfg >>= 5;
-
- ch_cfg->dest_per = cfg & 0x1f;
- cfg >>= 5;
-
- switch (cfg & 7) {
- case 0:
- ch_cfg->flow_cntrl = FC_MEM2MEM_DMA;
- break;
- case 1:
- ch_cfg->flow_cntrl = FC_MEM2PER_DMA;
- break;
- case 2:
- ch_cfg->flow_cntrl = FC_PER2MEM_DMA;
- break;
- case 3:
- ch_cfg->flow_cntrl = FC_PER2PER_DMA;
- break;
- case 4:
- ch_cfg->flow_cntrl = FC_PER2PER_DPER;
- break;
- case 5:
- ch_cfg->flow_cntrl = FC_MEM2PER_PER;
- break;
- case 6:
- ch_cfg->flow_cntrl = FC_PER2MEM_PER;
- break;
- case 7:
- ch_cfg->flow_cntrl = FC_PER2PER_SPER;
- }
- cfg >>= 3;
-
- ch_cfg->ie = cfg & 1;
- cfg >>= 1;
-
- ch_cfg->itc = cfg & 1;
- cfg >>= 1;
-
- ch_cfg->lock = cfg & 1;
- cfg >>= 1;
-
- ch_cfg->active = cfg & 1;
- cfg >>= 1;
-
- ch_cfg->halt = cfg & 1;
-
-out:
- return err;
-}
-
-EXPORT_SYMBOL_GPL(pnx4008_dma_parse_config);
-
-void pnx4008_dma_split_head_entry(struct pnx4008_dma_config * config,
- struct pnx4008_dma_ch_ctrl * ctrl)
-{
- int new_len = ctrl->tr_size, num_entries = 0;
- int old_len = new_len;
- int src_width, dest_width, count = 1;
-
- switch (ctrl->swidth) {
- case WIDTH_BYTE:
- src_width = 1;
- break;
- case WIDTH_HWORD:
- src_width = 2;
- break;
- case WIDTH_WORD:
- src_width = 4;
- break;
- default:
- return;
- }
-
- switch (ctrl->dwidth) {
- case WIDTH_BYTE:
- dest_width = 1;
- break;
- case WIDTH_HWORD:
- dest_width = 2;
- break;
- case WIDTH_WORD:
- dest_width = 4;
- break;
- default:
- return;
- }
-
- while (new_len > 0x7FF) {
- num_entries++;
- new_len = (ctrl->tr_size + num_entries) / (num_entries + 1);
- }
- if (num_entries != 0) {
- struct pnx4008_dma_ll *ll = NULL;
- config->ch_ctrl &= ~0x7ff;
- config->ch_ctrl |= new_len;
- if (!config->is_ll) {
- config->is_ll = 1;
- while (num_entries) {
- if (!ll) {
- config->ll =
- pnx4008_alloc_ll_entry(&config->
- ll_dma);
- ll = config->ll;
- } else {
- ll->next =
- pnx4008_alloc_ll_entry(&ll->
- next_dma);
- ll = ll->next;
- }
-
- if (ctrl->si)
- ll->src_addr =
- config->src_addr +
- src_width * new_len * count;
- else
- ll->src_addr = config->src_addr;
- if (ctrl->di)
- ll->dest_addr =
- config->dest_addr +
- dest_width * new_len * count;
- else
- ll->dest_addr = config->dest_addr;
- ll->ch_ctrl = config->ch_ctrl & 0x7fffffff;
- ll->next_dma = 0;
- ll->next = NULL;
- num_entries--;
- count++;
- }
- } else {
- struct pnx4008_dma_ll *ll_old = config->ll;
- unsigned long ll_dma_old = config->ll_dma;
- while (num_entries) {
- if (!ll) {
- config->ll =
- pnx4008_alloc_ll_entry(&config->
- ll_dma);
- ll = config->ll;
- } else {
- ll->next =
- pnx4008_alloc_ll_entry(&ll->
- next_dma);
- ll = ll->next;
- }
-
- if (ctrl->si)
- ll->src_addr =
- config->src_addr +
- src_width * new_len * count;
- else
- ll->src_addr = config->src_addr;
- if (ctrl->di)
- ll->dest_addr =
- config->dest_addr +
- dest_width * new_len * count;
- else
- ll->dest_addr = config->dest_addr;
- ll->ch_ctrl = config->ch_ctrl & 0x7fffffff;
- ll->next_dma = 0;
- ll->next = NULL;
- num_entries--;
- count++;
- }
- ll->next_dma = ll_dma_old;
- ll->next = ll_old;
- }
- /* adjust last length/tc */
- ll->ch_ctrl = config->ch_ctrl & (~0x7ff);
- ll->ch_ctrl |= old_len - new_len * (count - 1);
- config->ch_ctrl &= 0x7fffffff;
- }
-}
-
-EXPORT_SYMBOL_GPL(pnx4008_dma_split_head_entry);
-
-void pnx4008_dma_split_ll_entry(struct pnx4008_dma_ll * cur_ll,
- struct pnx4008_dma_ch_ctrl * ctrl)
-{
- int new_len = ctrl->tr_size, num_entries = 0;
- int old_len = new_len;
- int src_width, dest_width, count = 1;
-
- switch (ctrl->swidth) {
- case WIDTH_BYTE:
- src_width = 1;
- break;
- case WIDTH_HWORD:
- src_width = 2;
- break;
- case WIDTH_WORD:
- src_width = 4;
- break;
- default:
- return;
- }
-
- switch (ctrl->dwidth) {
- case WIDTH_BYTE:
- dest_width = 1;
- break;
- case WIDTH_HWORD:
- dest_width = 2;
- break;
- case WIDTH_WORD:
- dest_width = 4;
- break;
- default:
- return;
- }
-
- while (new_len > 0x7FF) {
- num_entries++;
- new_len = (ctrl->tr_size + num_entries) / (num_entries + 1);
- }
- if (num_entries != 0) {
- struct pnx4008_dma_ll *ll = NULL;
- cur_ll->ch_ctrl &= ~0x7ff;
- cur_ll->ch_ctrl |= new_len;
- if (!cur_ll->next) {
- while (num_entries) {
- if (!ll) {
- cur_ll->next =
- pnx4008_alloc_ll_entry(&cur_ll->
- next_dma);
- ll = cur_ll->next;
- } else {
- ll->next =
- pnx4008_alloc_ll_entry(&ll->
- next_dma);
- ll = ll->next;
- }
-
- if (ctrl->si)
- ll->src_addr =
- cur_ll->src_addr +
- src_width * new_len * count;
- else
- ll->src_addr = cur_ll->src_addr;
- if (ctrl->di)
- ll->dest_addr =
- cur_ll->dest_addr +
- dest_width * new_len * count;
- else
- ll->dest_addr = cur_ll->dest_addr;
- ll->ch_ctrl = cur_ll->ch_ctrl & 0x7fffffff;
- ll->next_dma = 0;
- ll->next = NULL;
- num_entries--;
- count++;
- }
- } else {
- struct pnx4008_dma_ll *ll_old = cur_ll->next;
- unsigned long ll_dma_old = cur_ll->next_dma;
- while (num_entries) {
- if (!ll) {
- cur_ll->next =
- pnx4008_alloc_ll_entry(&cur_ll->
- next_dma);
- ll = cur_ll->next;
- } else {
- ll->next =
- pnx4008_alloc_ll_entry(&ll->
- next_dma);
- ll = ll->next;
- }
-
- if (ctrl->si)
- ll->src_addr =
- cur_ll->src_addr +
- src_width * new_len * count;
- else
- ll->src_addr = cur_ll->src_addr;
- if (ctrl->di)
- ll->dest_addr =
- cur_ll->dest_addr +
- dest_width * new_len * count;
- else
- ll->dest_addr = cur_ll->dest_addr;
- ll->ch_ctrl = cur_ll->ch_ctrl & 0x7fffffff;
- ll->next_dma = 0;
- ll->next = NULL;
- num_entries--;
- count++;
- }
-
- ll->next_dma = ll_dma_old;
- ll->next = ll_old;
- }
- /* adjust last length/tc */
- ll->ch_ctrl = cur_ll->ch_ctrl & (~0x7ff);
- ll->ch_ctrl |= old_len - new_len * (count - 1);
- cur_ll->ch_ctrl &= 0x7fffffff;
- }
-}
-
-EXPORT_SYMBOL_GPL(pnx4008_dma_split_ll_entry);
-
-int pnx4008_config_channel(int ch, struct pnx4008_dma_config * config)
-{
- if (!VALID_CHANNEL(ch) || !dma_channels[ch].name)
- return -EINVAL;
-
- pnx4008_dma_lock();
- __raw_writel(config->src_addr, DMAC_Cx_SRC_ADDR(ch));
- __raw_writel(config->dest_addr, DMAC_Cx_DEST_ADDR(ch));
-
- if (config->is_ll)
- __raw_writel(config->ll_dma, DMAC_Cx_LLI(ch));
- else
- __raw_writel(0, DMAC_Cx_LLI(ch));
-
- __raw_writel(config->ch_ctrl, DMAC_Cx_CONTROL(ch));
- __raw_writel(config->ch_cfg, DMAC_Cx_CONFIG(ch));
- pnx4008_dma_unlock();
-
- return 0;
-
-}
-
-EXPORT_SYMBOL_GPL(pnx4008_config_channel);
-
-int pnx4008_channel_get_config(int ch, struct pnx4008_dma_config * config)
-{
- if (!VALID_CHANNEL(ch) || !dma_channels[ch].name || !config)
- return -EINVAL;
-
- pnx4008_dma_lock();
- config->ch_cfg = __raw_readl(DMAC_Cx_CONFIG(ch));
- config->ch_ctrl = __raw_readl(DMAC_Cx_CONTROL(ch));
-
- config->ll_dma = __raw_readl(DMAC_Cx_LLI(ch));
- config->is_ll = config->ll_dma ? 1 : 0;
-
- config->src_addr = __raw_readl(DMAC_Cx_SRC_ADDR(ch));
- config->dest_addr = __raw_readl(DMAC_Cx_DEST_ADDR(ch));
- pnx4008_dma_unlock();
-
- return 0;
-}
-
-EXPORT_SYMBOL_GPL(pnx4008_channel_get_config);
-
-int pnx4008_dma_ch_enable(int ch)
-{
- unsigned long ch_cfg;
-
- if (!VALID_CHANNEL(ch) || !dma_channels[ch].name)
- return -EINVAL;
-
- pnx4008_dma_lock();
- ch_cfg = __raw_readl(DMAC_Cx_CONFIG(ch));
- ch_cfg |= 1;
- __raw_writel(ch_cfg, DMAC_Cx_CONFIG(ch));
- pnx4008_dma_unlock();
-
- return 0;
-}
-
-EXPORT_SYMBOL_GPL(pnx4008_dma_ch_enable);
-
-int pnx4008_dma_ch_disable(int ch)
-{
- unsigned long ch_cfg;
-
- if (!VALID_CHANNEL(ch) || !dma_channels[ch].name)
- return -EINVAL;
-
- pnx4008_dma_lock();
- ch_cfg = __raw_readl(DMAC_Cx_CONFIG(ch));
- ch_cfg &= ~1;
- __raw_writel(ch_cfg, DMAC_Cx_CONFIG(ch));
- pnx4008_dma_unlock();
-
- return 0;
-}
-
-EXPORT_SYMBOL_GPL(pnx4008_dma_ch_disable);
-
-int pnx4008_dma_ch_enabled(int ch)
-{
- unsigned long ch_cfg;
-
- if (!VALID_CHANNEL(ch) || !dma_channels[ch].name)
- return -EINVAL;
-
- pnx4008_dma_lock();
- ch_cfg = __raw_readl(DMAC_Cx_CONFIG(ch));
- pnx4008_dma_unlock();
-
- return ch_cfg & 1;
-}
-
-EXPORT_SYMBOL_GPL(pnx4008_dma_ch_enabled);
-
-static irqreturn_t dma_irq_handler(int irq, void *dev_id)
-{
- int i;
- unsigned long dint = __raw_readl(DMAC_INT_STAT);
- unsigned long tcint = __raw_readl(DMAC_INT_TC_STAT);
- unsigned long eint = __raw_readl(DMAC_INT_ERR_STAT);
- unsigned long i_bit;
-
- for (i = MAX_DMA_CHANNELS - 1; i >= 0; i--) {
- i_bit = 1 << i;
- if (dint & i_bit) {
- struct dma_channel *channel = &dma_channels[i];
-
- if (channel->name && channel->irq_handler) {
- int cause = 0;
-
- if (eint & i_bit)
- cause |= DMA_ERR_INT;
- if (tcint & i_bit)
- cause |= DMA_TC_INT;
- channel->irq_handler(i, cause, channel->data);
- } else {
- /*
- * IRQ for an unregistered DMA channel
- */
- printk(KERN_WARNING
- "spurious IRQ for DMA channel %d\n", i);
- }
- if (tcint & i_bit)
- __raw_writel(i_bit, DMAC_INT_TC_CLEAR);
- if (eint & i_bit)
- __raw_writel(i_bit, DMAC_INT_ERR_CLEAR);
- }
- }
- return IRQ_HANDLED;
-}
-
-static int __init pnx4008_dma_init(void)
-{
- int ret, i;
-
- ret = request_irq(DMA_INT, dma_irq_handler, 0, "DMA", NULL);
- if (ret) {
- printk(KERN_CRIT "Wow! Can't register IRQ for DMA\n");
- goto out;
- }
-
- ll_pool.count = 0x4000 / sizeof(struct pnx4008_dma_ll);
- ll_pool.cur = ll_pool.vaddr =
- dma_alloc_coherent(NULL, ll_pool.count * sizeof(struct pnx4008_dma_ll),
- &ll_pool.dma_addr, GFP_KERNEL);
-
- if (!ll_pool.vaddr) {
- ret = -ENOMEM;
- free_irq(DMA_INT, NULL);
- goto out;
- }
-
- for (i = 0; i < ll_pool.count - 1; i++) {
- void **addr = ll_pool.vaddr + i * sizeof(struct pnx4008_dma_ll);
- *addr = (void *)addr + sizeof(struct pnx4008_dma_ll);
- }
- *(long *)(ll_pool.vaddr +
- (ll_pool.count - 1) * sizeof(struct pnx4008_dma_ll)) =
- (long)ll_pool.vaddr;
-
- __raw_writel(1, DMAC_CONFIG);
-
-out:
- return ret;
-}
-arch_initcall(pnx4008_dma_init);
@@ -1,328 +0,0 @@
-/*
- * arch/arm/mach-pnx4008/gpio.c
- *
- * PNX4008 GPIO driver
- *
- * Author: Dmitry Chigirev <source@mvista.com>
- *
- * Based on reference code by Iwo Mergler and Z.Tabaaloute from Philips:
- * Copyright (c) 2005 Koninklijke Philips Electronics N.V.
- *
- * 2005 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/io.h>
-#include <mach/hardware.h>
-#include <mach/platform.h>
-#include <mach/gpio-pnx4008.h>
-
-/* register definitions */
-#define PIO_VA_BASE IO_ADDRESS(PNX4008_PIO_BASE)
-
-#define PIO_INP_STATE (0x00U)
-#define PIO_OUTP_SET (0x04U)
-#define PIO_OUTP_CLR (0x08U)
-#define PIO_OUTP_STATE (0x0CU)
-#define PIO_DRV_SET (0x10U)
-#define PIO_DRV_CLR (0x14U)
-#define PIO_DRV_STATE (0x18U)
-#define PIO_SDINP_STATE (0x1CU)
-#define PIO_SDOUTP_SET (0x20U)
-#define PIO_SDOUTP_CLR (0x24U)
-#define PIO_MUX_SET (0x28U)
-#define PIO_MUX_CLR (0x2CU)
-#define PIO_MUX_STATE (0x30U)
-
-static inline void gpio_lock(void)
-{
- local_irq_disable();
-}
-
-static inline void gpio_unlock(void)
-{
- local_irq_enable();
-}
-
-/* Inline functions */
-static inline int gpio_read_bit(u32 reg, int gpio)
-{
- u32 bit, val;
- int ret = -EFAULT;
-
- if (gpio < 0)
- goto out;
-
- bit = GPIO_BIT(gpio);
- if (bit) {
- val = __raw_readl(PIO_VA_BASE + reg);
- ret = (val & bit) ? 1 : 0;
- }
-out:
- return ret;
-}
-
-static inline int gpio_set_bit(u32 reg, int gpio)
-{
- u32 bit, val;
- int ret = -EFAULT;
-
- if (gpio < 0)
- goto out;
-
- bit = GPIO_BIT(gpio);
- if (bit) {
- val = __raw_readl(PIO_VA_BASE + reg);
- val |= bit;
- __raw_writel(val, PIO_VA_BASE + reg);
- ret = 0;
- }
-out:
- return ret;
-}
-
-/* Very simple access control, bitmap for allocated/free */
-static unsigned long access_map[4];
-#define INP_INDEX 0
-#define OUTP_INDEX 1
-#define GPIO_INDEX 2
-#define MUX_INDEX 3
-
-/*GPIO to Input Mapping */
-static short gpio_to_inp_map[32] = {
- -1, -1, -1, -1, -1, -1, -1, -1,
- -1, -1, -1, -1, -1, -1, -1, -1,
- -1, -1, -1, -1, -1, -1, -1, -1,
- -1, 10, 11, 12, 13, 14, 24, -1
-};
-
-/*GPIO to Mux Mapping */
-static short gpio_to_mux_map[32] = {
- -1, -1, -1, -1, -1, -1, -1, -1,
- -1, -1, -1, -1, -1, -1, -1, -1,
- -1, -1, -1, -1, -1, -1, -1, -1,
- -1, -1, -1, 0, 1, 4, 5, -1
-};
-
-/*Output to Mux Mapping */
-static short outp_to_mux_map[32] = {
- -1, -1, -1, 6, -1, -1, -1, -1,
- -1, -1, -1, -1, -1, -1, -1, -1,
- -1, -1, -1, -1, -1, 2, -1, -1,
- -1, -1, -1, -1, -1, -1, -1, -1
-};
-
-int pnx4008_gpio_register_pin(unsigned short pin)
-{
- unsigned long bit = GPIO_BIT(pin);
- int ret = -EBUSY; /* Already in use */
-
- gpio_lock();
-
- if (GPIO_ISBID(pin)) {
- if (access_map[GPIO_INDEX] & bit)
- goto out;
- access_map[GPIO_INDEX] |= bit;
-
- } else if (GPIO_ISRAM(pin)) {
- if (access_map[GPIO_INDEX] & bit)
- goto out;
- access_map[GPIO_INDEX] |= bit;
-
- } else if (GPIO_ISMUX(pin)) {
- if (access_map[MUX_INDEX] & bit)
- goto out;
- access_map[MUX_INDEX] |= bit;
-
- } else if (GPIO_ISOUT(pin)) {
- if (access_map[OUTP_INDEX] & bit)
- goto out;
- access_map[OUTP_INDEX] |= bit;
-
- } else if (GPIO_ISIN(pin)) {
- if (access_map[INP_INDEX] & bit)
- goto out;
- access_map[INP_INDEX] |= bit;
- } else
- goto out;
- ret = 0;
-
-out:
- gpio_unlock();
- return ret;
-}
-
-EXPORT_SYMBOL(pnx4008_gpio_register_pin);
-
-int pnx4008_gpio_unregister_pin(unsigned short pin)
-{
- unsigned long bit = GPIO_BIT(pin);
- int ret = -EFAULT; /* Not registered */
-
- gpio_lock();
-
- if (GPIO_ISBID(pin)) {
- if (~access_map[GPIO_INDEX] & bit)
- goto out;
- access_map[GPIO_INDEX] &= ~bit;
- } else if (GPIO_ISRAM(pin)) {
- if (~access_map[GPIO_INDEX] & bit)
- goto out;
- access_map[GPIO_INDEX] &= ~bit;
- } else if (GPIO_ISMUX(pin)) {
- if (~access_map[MUX_INDEX] & bit)
- goto out;
- access_map[MUX_INDEX] &= ~bit;
- } else if (GPIO_ISOUT(pin)) {
- if (~access_map[OUTP_INDEX] & bit)
- goto out;
- access_map[OUTP_INDEX] &= ~bit;
- } else if (GPIO_ISIN(pin)) {
- if (~access_map[INP_INDEX] & bit)
- goto out;
- access_map[INP_INDEX] &= ~bit;
- } else
- goto out;
- ret = 0;
-
-out:
- gpio_unlock();
- return ret;
-}
-
-EXPORT_SYMBOL(pnx4008_gpio_unregister_pin);
-
-unsigned long pnx4008_gpio_read_pin(unsigned short pin)
-{
- unsigned long ret = -EFAULT;
- int gpio = GPIO_BIT_MASK(pin);
- gpio_lock();
- if (GPIO_ISOUT(pin)) {
- ret = gpio_read_bit(PIO_OUTP_STATE, gpio);
- } else if (GPIO_ISRAM(pin)) {
- if (gpio_read_bit(PIO_DRV_STATE, gpio) == 0) {
- ret = gpio_read_bit(PIO_SDINP_STATE, gpio);
- }
- } else if (GPIO_ISBID(pin)) {
- ret = gpio_read_bit(PIO_DRV_STATE, gpio);
- if (ret > 0)
- ret = gpio_read_bit(PIO_OUTP_STATE, gpio);
- else if (ret == 0)
- ret =
- gpio_read_bit(PIO_INP_STATE, gpio_to_inp_map[gpio]);
- } else if (GPIO_ISIN(pin)) {
- ret = gpio_read_bit(PIO_INP_STATE, gpio);
- }
- gpio_unlock();
- return ret;
-}
-
-EXPORT_SYMBOL(pnx4008_gpio_read_pin);
-
-/* Write Value to output */
-int pnx4008_gpio_write_pin(unsigned short pin, int output)
-{
- int gpio = GPIO_BIT_MASK(pin);
- int ret = -EFAULT;
-
- gpio_lock();
- if (GPIO_ISOUT(pin)) {
- printk( "writing '%x' to '%x'\n",
- gpio, output ? PIO_OUTP_SET : PIO_OUTP_CLR );
- ret = gpio_set_bit(output ? PIO_OUTP_SET : PIO_OUTP_CLR, gpio);
- } else if (GPIO_ISRAM(pin)) {
- if (gpio_read_bit(PIO_DRV_STATE, gpio) > 0)
- ret = gpio_set_bit(output ? PIO_SDOUTP_SET :
- PIO_SDOUTP_CLR, gpio);
- } else if (GPIO_ISBID(pin)) {
- if (gpio_read_bit(PIO_DRV_STATE, gpio) > 0)
- ret = gpio_set_bit(output ? PIO_OUTP_SET :
- PIO_OUTP_CLR, gpio);
- }
- gpio_unlock();
- return ret;
-}
-
-EXPORT_SYMBOL(pnx4008_gpio_write_pin);
-
-/* Value = 1 : Set GPIO pin as output */
-/* Value = 0 : Set GPIO pin as input */
-int pnx4008_gpio_set_pin_direction(unsigned short pin, int output)
-{
- int gpio = GPIO_BIT_MASK(pin);
- int ret = -EFAULT;
-
- gpio_lock();
- if (GPIO_ISBID(pin) || GPIO_ISRAM(pin)) {
- ret = gpio_set_bit(output ? PIO_DRV_SET : PIO_DRV_CLR, gpio);
- }
- gpio_unlock();
- return ret;
-}
-
-EXPORT_SYMBOL(pnx4008_gpio_set_pin_direction);
-
-/* Read GPIO pin direction: 0= pin used as input, 1= pin used as output*/
-int pnx4008_gpio_read_pin_direction(unsigned short pin)
-{
- int gpio = GPIO_BIT_MASK(pin);
- int ret = -EFAULT;
-
- gpio_lock();
- if (GPIO_ISBID(pin) || GPIO_ISRAM(pin)) {
- ret = gpio_read_bit(PIO_DRV_STATE, gpio);
- }
- gpio_unlock();
- return ret;
-}
-
-EXPORT_SYMBOL(pnx4008_gpio_read_pin_direction);
-
-/* Value = 1 : Set pin to muxed function */
-/* Value = 0 : Set pin as GPIO */
-int pnx4008_gpio_set_pin_mux(unsigned short pin, int output)
-{
- int gpio = GPIO_BIT_MASK(pin);
- int ret = -EFAULT;
-
- gpio_lock();
- if (GPIO_ISBID(pin)) {
- ret =
- gpio_set_bit(output ? PIO_MUX_SET : PIO_MUX_CLR,
- gpio_to_mux_map[gpio]);
- } else if (GPIO_ISOUT(pin)) {
- ret =
- gpio_set_bit(output ? PIO_MUX_SET : PIO_MUX_CLR,
- outp_to_mux_map[gpio]);
- } else if (GPIO_ISMUX(pin)) {
- ret = gpio_set_bit(output ? PIO_MUX_SET : PIO_MUX_CLR, gpio);
- }
- gpio_unlock();
- return ret;
-}
-
-EXPORT_SYMBOL(pnx4008_gpio_set_pin_mux);
-
-/* Read pin mux function: 0= pin used as GPIO, 1= pin used for muxed function*/
-int pnx4008_gpio_read_pin_mux(unsigned short pin)
-{
- int gpio = GPIO_BIT_MASK(pin);
- int ret = -EFAULT;
-
- gpio_lock();
- if (GPIO_ISBID(pin)) {
- ret = gpio_read_bit(PIO_MUX_STATE, gpio_to_mux_map[gpio]);
- } else if (GPIO_ISOUT(pin)) {
- ret = gpio_read_bit(PIO_MUX_STATE, outp_to_mux_map[gpio]);
- } else if (GPIO_ISMUX(pin)) {
- ret = gpio_read_bit(PIO_MUX_STATE, gpio);
- }
- gpio_unlock();
- return ret;
-}
-
-EXPORT_SYMBOL(pnx4008_gpio_read_pin_mux);
@@ -1,86 +0,0 @@
-/*
- * I2C initialization for PNX4008.
- *
- * Author: Vitaly Wool <vitalywool@gmail.com>
- *
- * 2005-2006 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-
-#include <linux/clk.h>
-#include <linux/i2c.h>
-#include <linux/i2c-pnx.h>
-#include <linux/platform_device.h>
-#include <linux/err.h>
-#include <mach/platform.h>
-#include <mach/irqs.h>
-
-static struct resource i2c0_resources[] = {
- {
- .start = PNX4008_I2C1_BASE,
- .end = PNX4008_I2C1_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = I2C_1_INT,
- .end = I2C_1_INT,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct resource i2c1_resources[] = {
- {
- .start = PNX4008_I2C2_BASE,
- .end = PNX4008_I2C2_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = I2C_2_INT,
- .end = I2C_2_INT,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct resource i2c2_resources[] = {
- {
- .start = PNX4008_USB_CONFIG_BASE + 0x300,
- .end = PNX4008_USB_CONFIG_BASE + 0x300 + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .start = USB_I2C_INT,
- .end = USB_I2C_INT,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device i2c0_device = {
- .name = "pnx-i2c.0",
- .id = 0,
- .resource = i2c0_resources,
- .num_resources = ARRAY_SIZE(i2c0_resources),
-};
-
-static struct platform_device i2c1_device = {
- .name = "pnx-i2c.1",
- .id = 1,
- .resource = i2c1_resources,
- .num_resources = ARRAY_SIZE(i2c1_resources),
-};
-
-static struct platform_device i2c2_device = {
- .name = "pnx-i2c.2",
- .id = 2,
- .resource = i2c2_resources,
- .num_resources = ARRAY_SIZE(i2c2_resources),
-};
-
-static struct platform_device *devices[] __initdata = {
- &i2c0_device,
- &i2c1_device,
- &i2c2_device,
-};
-
-void __init pnx4008_register_i2c_devices(void)
-{
- platform_add_devices(devices, ARRAY_SIZE(devices));
-}
@@ -1,62 +0,0 @@
-/*
- * arch/arm/mach-pnx4008/include/mach/clock.h
- *
- * Clock control driver for PNX4008 - header file
- *
- * Authors: Vitaly Wool, Dmitry Chigirev <source@mvista.com>
- *
- * 2005 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-#ifndef __PNX4008_CLOCK_H__
-#define __PNX4008_CLOCK_H__
-
-struct module;
-struct clk;
-
-#define PWRMAN_VA_BASE IO_ADDRESS(PNX4008_PWRMAN_BASE)
-#define HCLKDIVCTRL_REG (PWRMAN_VA_BASE + 0x40)
-#define PWRCTRL_REG (PWRMAN_VA_BASE + 0x44)
-#define PLLCTRL_REG (PWRMAN_VA_BASE + 0x48)
-#define OSC13CTRL_REG (PWRMAN_VA_BASE + 0x4c)
-#define SYSCLKCTRL_REG (PWRMAN_VA_BASE + 0x50)
-#define HCLKPLLCTRL_REG (PWRMAN_VA_BASE + 0x58)
-#define USBCTRL_REG (PWRMAN_VA_BASE + 0x64)
-#define SDRAMCLKCTRL_REG (PWRMAN_VA_BASE + 0x68)
-#define MSCTRL_REG (PWRMAN_VA_BASE + 0x80)
-#define BTCLKCTRL (PWRMAN_VA_BASE + 0x84)
-#define DUMCLKCTRL_REG (PWRMAN_VA_BASE + 0x90)
-#define I2CCLKCTRL_REG (PWRMAN_VA_BASE + 0xac)
-#define KEYCLKCTRL_REG (PWRMAN_VA_BASE + 0xb0)
-#define TSCLKCTRL_REG (PWRMAN_VA_BASE + 0xb4)
-#define PWMCLKCTRL_REG (PWRMAN_VA_BASE + 0xb8)
-#define TIMCLKCTRL_REG (PWRMAN_VA_BASE + 0xbc)
-#define SPICTRL_REG (PWRMAN_VA_BASE + 0xc4)
-#define FLASHCLKCTRL_REG (PWRMAN_VA_BASE + 0xc8)
-#define UART3CLK_REG (PWRMAN_VA_BASE + 0xd0)
-#define UARTCLKCTRL_REG (PWRMAN_VA_BASE + 0xe4)
-#define DMACLKCTRL_REG (PWRMAN_VA_BASE + 0xe8)
-#define AUTOCLK_CTRL (PWRMAN_VA_BASE + 0xec)
-#define JPEGCLKCTRL_REG (PWRMAN_VA_BASE + 0xfc)
-
-#define AUDIOCONFIG_VA_BASE IO_ADDRESS(PNX4008_AUDIOCONFIG_BASE)
-#define DSPPLLCTRL_REG (AUDIOCONFIG_VA_BASE + 0x60)
-#define DSPCLKCTRL_REG (AUDIOCONFIG_VA_BASE + 0x64)
-#define AUDIOCLKCTRL_REG (AUDIOCONFIG_VA_BASE + 0x68)
-#define AUDIOPLLCTRL_REG (AUDIOCONFIG_VA_BASE + 0x6C)
-
-#define USB_OTG_CLKCTRL_REG IO_ADDRESS(PNX4008_USB_CONFIG_BASE + 0xff4)
-
-#define VFP9CLKCTRL_REG IO_ADDRESS(PNX4008_DEBUG_BASE)
-
-#define CLK_RATE_13MHZ 13000
-#define CLK_RATE_1MHZ 1000
-#define CLK_RATE_208MHZ 208000
-#define CLK_RATE_48MHZ 48000
-#define CLK_RATE_32KHZ 32
-
-#define PNX4008_UART_CLK CLK_RATE_13MHZ * 1000 /* in MHz */
-
-#endif
@@ -1,21 +0,0 @@
-/* arch/arm/mach-pnx4008/include/mach/debug-macro.S
- *
- * Debugging macro include header
- *
- * Copyright (C) 1994-1999 Russell King
- * Moved from linux/arch/arm/kernel/debug.S by Ben Dooks
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
-*/
-
- .macro addruart, rp, rv, tmp
- mov \rp, #0x00090000
- add \rv, \rp, #0xf4000000 @ virtual
- add \rp, \rp, #0x40000000 @ physical
- .endm
-
-#define UART_SHIFT 2
-#include <asm/hardware/debug-8250.S>
@@ -1,160 +0,0 @@
-/*
- * arch/arm/mach-pnx4008/include/mach/dma.h
- *
- * PNX4008 DMA header file
- *
- * Author: Vitaly Wool
- * Copyright: MontaVista Software Inc. (c) 2005
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_DMA_H
-#define __ASM_ARCH_DMA_H
-
-#include "platform.h"
-
-#define MAX_DMA_CHANNELS 8
-
-#define DMAC_BASE IO_ADDRESS(PNX4008_DMA_CONFIG_BASE)
-#define DMAC_INT_STAT (DMAC_BASE + 0x0000)
-#define DMAC_INT_TC_STAT (DMAC_BASE + 0x0004)
-#define DMAC_INT_TC_CLEAR (DMAC_BASE + 0x0008)
-#define DMAC_INT_ERR_STAT (DMAC_BASE + 0x000c)
-#define DMAC_INT_ERR_CLEAR (DMAC_BASE + 0x0010)
-#define DMAC_SOFT_SREQ (DMAC_BASE + 0x0024)
-#define DMAC_CONFIG (DMAC_BASE + 0x0030)
-#define DMAC_Cx_SRC_ADDR(c) (DMAC_BASE + 0x0100 + (c) * 0x20)
-#define DMAC_Cx_DEST_ADDR(c) (DMAC_BASE + 0x0104 + (c) * 0x20)
-#define DMAC_Cx_LLI(c) (DMAC_BASE + 0x0108 + (c) * 0x20)
-#define DMAC_Cx_CONTROL(c) (DMAC_BASE + 0x010c + (c) * 0x20)
-#define DMAC_Cx_CONFIG(c) (DMAC_BASE + 0x0110 + (c) * 0x20)
-
-enum {
- WIDTH_BYTE = 0,
- WIDTH_HWORD,
- WIDTH_WORD
-};
-
-enum {
- FC_MEM2MEM_DMA,
- FC_MEM2PER_DMA,
- FC_PER2MEM_DMA,
- FC_PER2PER_DMA,
- FC_PER2PER_DPER,
- FC_MEM2PER_PER,
- FC_PER2MEM_PER,
- FC_PER2PER_SPER
-};
-
-enum {
- DMA_INT_UNKNOWN = 0,
- DMA_ERR_INT = 1,
- DMA_TC_INT = 2,
-};
-
-enum {
- DMA_BUFFER_ALLOCATED = 1,
- DMA_HAS_LL = 2,
-};
-
-enum {
- PER_CAM_DMA_1 = 0,
- PER_NDF_FLASH = 1,
- PER_MBX_SLAVE_FIFO = 2,
- PER_SPI2_REC_XMIT = 3,
- PER_MS_SD_RX_XMIT = 4,
- PER_HS_UART_1_XMIT = 5,
- PER_HS_UART_1_RX = 6,
- PER_HS_UART_2_XMIT = 7,
- PER_HS_UART_2_RX = 8,
- PER_HS_UART_7_XMIT = 9,
- PER_HS_UART_7_RX = 10,
- PER_SPI1_REC_XMIT = 11,
- PER_MLC_NDF_SREC = 12,
- PER_CAM_DMA_2 = 13,
- PER_PRNG_INFIFO = 14,
- PER_PRNG_OUTFIFO = 15,
-};
-
-struct pnx4008_dma_ch_ctrl {
- int tc_mask;
- int cacheable;
- int bufferable;
- int priv_mode;
- int di;
- int si;
- int dest_ahb1;
- int src_ahb1;
- int dwidth;
- int swidth;
- int dbsize;
- int sbsize;
- int tr_size;
-};
-
-struct pnx4008_dma_ch_config {
- int halt;
- int active;
- int lock;
- int itc;
- int ie;
- int flow_cntrl;
- int dest_per;
- int src_per;
-};
-
-struct pnx4008_dma_ll {
- unsigned long src_addr;
- unsigned long dest_addr;
- u32 next_dma;
- unsigned long ch_ctrl;
- struct pnx4008_dma_ll *next;
- int flags;
- void *alloc_data;
- int (*free) (void *);
-};
-
-struct pnx4008_dma_config {
- int is_ll;
- unsigned long src_addr;
- unsigned long dest_addr;
- unsigned long ch_ctrl;
- unsigned long ch_cfg;
- struct pnx4008_dma_ll *ll;
- u32 ll_dma;
- int flags;
- void *alloc_data;
- int (*free) (void *);
-};
-
-extern struct pnx4008_dma_ll *pnx4008_alloc_ll_entry(dma_addr_t *);
-extern void pnx4008_free_ll_entry(struct pnx4008_dma_ll *, dma_addr_t);
-extern void pnx4008_free_ll(u32 ll_dma, struct pnx4008_dma_ll *);
-
-extern int pnx4008_request_channel(char *, int,
- void (*)(int, int, void *),
- void *);
-extern void pnx4008_free_channel(int);
-extern int pnx4008_config_dma(int, int, int);
-extern int pnx4008_dma_pack_control(const struct pnx4008_dma_ch_ctrl *,
- unsigned long *);
-extern int pnx4008_dma_parse_control(unsigned long,
- struct pnx4008_dma_ch_ctrl *);
-extern int pnx4008_dma_pack_config(const struct pnx4008_dma_ch_config *,
- unsigned long *);
-extern int pnx4008_dma_parse_config(unsigned long,
- struct pnx4008_dma_ch_config *);
-extern int pnx4008_config_channel(int, struct pnx4008_dma_config *);
-extern int pnx4008_channel_get_config(int, struct pnx4008_dma_config *);
-extern int pnx4008_dma_ch_enable(int);
-extern int pnx4008_dma_ch_disable(int);
-extern int pnx4008_dma_ch_enabled(int);
-extern void pnx4008_dma_split_head_entry(struct pnx4008_dma_config *,
- struct pnx4008_dma_ch_ctrl *);
-extern void pnx4008_dma_split_ll_entry(struct pnx4008_dma_ll *,
- struct pnx4008_dma_ch_ctrl *);
-
-#endif /* _ASM_ARCH_DMA_H */
@@ -1,116 +0,0 @@
-/*
- * arch/arm/mach-pnx4008/include/mach/entry-macro.S
- *
- * Low-level IRQ helper macros for PNX4008-based platforms
- *
- * 2005-2006 (c) MontaVista Software, Inc.
- * Author: Vitaly Wool <vwool@ru.mvista.com>
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include "platform.h"
-
-#define IO_BASE 0xF0000000
-#define IO_ADDRESS(x) (((((x) & 0xff000000) >> 4) | ((x) & 0xfffff)) | IO_BASE)
-
-#define INTRC_MASK 0x00
-#define INTRC_RAW_STAT 0x04
-#define INTRC_STAT 0x08
-#define INTRC_POLAR 0x0C
-#define INTRC_ACT_TYPE 0x10
-#define INTRC_TYPE 0x14
-
-#define SIC1_BASE_INT 32
-#define SIC2_BASE_INT 64
-
- .macro get_irqnr_preamble, base, tmp
- .endm
-
- .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
-/* decode the MIC interrupt numbers */
- ldr \base, =IO_ADDRESS(PNX4008_INTCTRLMIC_BASE)
- ldr \irqstat, [\base, #INTRC_STAT]
-
- cmp \irqstat,#1<<16
- movhs \irqnr,#16
- movlo \irqnr,#0
- movhs \irqstat,\irqstat,lsr#16
- cmp \irqstat,#1<<8
- addhs \irqnr,\irqnr,#8
- movhs \irqstat,\irqstat,lsr#8
- cmp \irqstat,#1<<4
- addhs \irqnr,\irqnr,#4
- movhs \irqstat,\irqstat,lsr#4
- cmp \irqstat,#1<<2
- addhs \irqnr,\irqnr,#2
- movhs \irqstat,\irqstat,lsr#2
- cmp \irqstat,#1<<1
- addhs \irqnr,\irqnr,#1
-
-/* was there an interrupt ? if not then drop out with EQ status */
- teq \irqstat,#0
- beq 1003f
-
-/* and now check for extended IRQ reasons */
- cmp \irqnr,#1
- bls 1003f
- cmp \irqnr,#30
- blo 1002f
-
-/* IRQ 31,30 : High priority cascade IRQ handle */
-/* read the correct SIC */
-/* decoding status after compare : eq is 30 (SIC1) , ne is 31 (SIC2) */
-/* set the base IRQ number */
- ldreq \base, =IO_ADDRESS(PNX4008_INTCTRLSIC1_BASE)
- moveq \irqnr,#SIC1_BASE_INT
- ldrne \base, =IO_ADDRESS(PNX4008_INTCTRLSIC2_BASE)
- movne \irqnr,#SIC2_BASE_INT
- ldr \irqstat, [\base, #INTRC_STAT]
- ldr \tmp, [\base, #INTRC_TYPE]
-/* and with inverted mask : low priority interrupts */
- and \irqstat,\irqstat,\tmp
- b 1004f
-
-1003:
-/* IRQ 1,0 : Low priority cascade IRQ handle */
-/* read the correct SIC */
-/* decoding status after compare : eq is 1 (SIC2) , ne is 0 (SIC1)*/
-/* read the correct SIC */
-/* set the base IRQ number */
- ldrne \base, =IO_ADDRESS(PNX4008_INTCTRLSIC1_BASE)
- movne \irqnr,#SIC1_BASE_INT
- ldreq \base, =IO_ADDRESS(PNX4008_INTCTRLSIC2_BASE)
- moveq \irqnr,#SIC2_BASE_INT
- ldr \irqstat, [\base, #INTRC_STAT]
- ldr \tmp, [\base, #INTRC_TYPE]
-/* and with inverted mask : low priority interrupts */
- bic \irqstat,\irqstat,\tmp
-
-1004:
-
- cmp \irqstat,#1<<16
- addhs \irqnr,\irqnr,#16
- movhs \irqstat,\irqstat,lsr#16
- cmp \irqstat,#1<<8
- addhs \irqnr,\irqnr,#8
- movhs \irqstat,\irqstat,lsr#8
- cmp \irqstat,#1<<4
- addhs \irqnr,\irqnr,#4
- movhs \irqstat,\irqstat,lsr#4
- cmp \irqstat,#1<<2
- addhs \irqnr,\irqnr,#2
- movhs \irqstat,\irqstat,lsr#2
- cmp \irqstat,#1<<1
- addhs \irqnr,\irqnr,#1
-
-
-/* is irqstat not zero */
-
-1002:
-/* we assert that irqstat is not equal to zero and return ne status if true*/
- teq \irqstat,#0
-1003:
- .endm
-
@@ -1,241 +0,0 @@
-/*
- * arch/arm/mach-pnx4008/include/mach/gpio-pnx4008.h
- *
- * PNX4008 GPIO driver - header file
- *
- * Author: Dmitry Chigirev <source@mvista.com>
- *
- * Based on reference code by Iwo Mergler and Z.Tabaaloute from Philips:
- * Copyright (c) 2005 Koninklijke Philips Electronics N.V.
- *
- * 2005 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-
-#ifndef _PNX4008_GPIO_H_
-#define _PNX4008_GPIO_H_
-
-
-/* Block numbers */
-#define GPIO_IN (0)
-#define GPIO_OUT (0x100)
-#define GPIO_BID (0x200)
-#define GPIO_RAM (0x300)
-#define GPIO_MUX (0x400)
-
-#define GPIO_TYPE_MASK(K) ((K) & 0x700)
-
-/* INPUT GPIOs */
-/* GPI */
-#define GPI_00 (GPIO_IN | 0)
-#define GPI_01 (GPIO_IN | 1)
-#define GPI_02 (GPIO_IN | 2)
-#define GPI_03 (GPIO_IN | 3)
-#define GPI_04 (GPIO_IN | 4)
-#define GPI_05 (GPIO_IN | 5)
-#define GPI_06 (GPIO_IN | 6)
-#define GPI_07 (GPIO_IN | 7)
-#define GPI_08 (GPIO_IN | 8)
-#define GPI_09 (GPIO_IN | 9)
-#define U1_RX (GPIO_IN | 15)
-#define U2_HTCS (GPIO_IN | 16)
-#define U2_RX (GPIO_IN | 17)
-#define U3_RX (GPIO_IN | 18)
-#define U4_RX (GPIO_IN | 19)
-#define U5_RX (GPIO_IN | 20)
-#define U6_IRRX (GPIO_IN | 21)
-#define U7_HCTS (GPIO_IN | 22)
-#define U7_RX (GPIO_IN | 23)
-/* MISC IN */
-#define SPI1_DATIN (GPIO_IN | 25)
-#define DISP_SYNC (GPIO_IN | 26)
-#define SPI2_DATIN (GPIO_IN | 27)
-#define GPI_11 (GPIO_IN | 28)
-
-#define GPIO_IN_MASK 0x1eff83ff
-
-/* OUTPUT GPIOs */
-/* GPO */
-#define GPO_00 (GPIO_OUT | 0)
-#define GPO_01 (GPIO_OUT | 1)
-#define GPO_02 (GPIO_OUT | 2)
-#define GPO_03 (GPIO_OUT | 3)
-#define GPO_04 (GPIO_OUT | 4)
-#define GPO_05 (GPIO_OUT | 5)
-#define GPO_06 (GPIO_OUT | 6)
-#define GPO_07 (GPIO_OUT | 7)
-#define GPO_08 (GPIO_OUT | 8)
-#define GPO_09 (GPIO_OUT | 9)
-#define GPO_10 (GPIO_OUT | 10)
-#define GPO_11 (GPIO_OUT | 11)
-#define GPO_12 (GPIO_OUT | 12)
-#define GPO_13 (GPIO_OUT | 13)
-#define GPO_14 (GPIO_OUT | 14)
-#define GPO_15 (GPIO_OUT | 15)
-#define GPO_16 (GPIO_OUT | 16)
-#define GPO_17 (GPIO_OUT | 17)
-#define GPO_18 (GPIO_OUT | 18)
-#define GPO_19 (GPIO_OUT | 19)
-#define GPO_20 (GPIO_OUT | 20)
-#define GPO_21 (GPIO_OUT | 21)
-#define GPO_22 (GPIO_OUT | 22)
-#define GPO_23 (GPIO_OUT | 23)
-
-#define GPIO_OUT_MASK 0xffffff
-
-/* BIDIRECTIONAL GPIOs */
-/* RAM pins */
-#define RAM_D19 (GPIO_RAM | 0)
-#define RAM_D20 (GPIO_RAM | 1)
-#define RAM_D21 (GPIO_RAM | 2)
-#define RAM_D22 (GPIO_RAM | 3)
-#define RAM_D23 (GPIO_RAM | 4)
-#define RAM_D24 (GPIO_RAM | 5)
-#define RAM_D25 (GPIO_RAM | 6)
-#define RAM_D26 (GPIO_RAM | 7)
-#define RAM_D27 (GPIO_RAM | 8)
-#define RAM_D28 (GPIO_RAM | 9)
-#define RAM_D29 (GPIO_RAM | 10)
-#define RAM_D30 (GPIO_RAM | 11)
-#define RAM_D31 (GPIO_RAM | 12)
-
-#define GPIO_RAM_MASK 0x1fff
-
-/* I/O pins */
-#define GPIO_00 (GPIO_BID | 25)
-#define GPIO_01 (GPIO_BID | 26)
-#define GPIO_02 (GPIO_BID | 27)
-#define GPIO_03 (GPIO_BID | 28)
-#define GPIO_04 (GPIO_BID | 29)
-#define GPIO_05 (GPIO_BID | 30)
-
-#define GPIO_BID_MASK 0x7e000000
-
-/* Non-GPIO multiplexed PIOs. For multiplexing with GPIO, please use GPIO macros */
-#define GPIO_SDRAM_SEL (GPIO_MUX | 3)
-
-#define GPIO_MUX_MASK 0x8
-
-/* Extraction/assembly macros */
-#define GPIO_BIT_MASK(K) ((K) & 0x1F)
-#define GPIO_BIT(K) (1 << GPIO_BIT_MASK(K))
-#define GPIO_ISMUX(K) ((GPIO_TYPE_MASK(K) == GPIO_MUX) && (GPIO_BIT(K) & GPIO_MUX_MASK))
-#define GPIO_ISRAM(K) ((GPIO_TYPE_MASK(K) == GPIO_RAM) && (GPIO_BIT(K) & GPIO_RAM_MASK))
-#define GPIO_ISBID(K) ((GPIO_TYPE_MASK(K) == GPIO_BID) && (GPIO_BIT(K) & GPIO_BID_MASK))
-#define GPIO_ISOUT(K) ((GPIO_TYPE_MASK(K) == GPIO_OUT) && (GPIO_BIT(K) & GPIO_OUT_MASK))
-#define GPIO_ISIN(K) ((GPIO_TYPE_MASK(K) == GPIO_IN) && (GPIO_BIT(K) & GPIO_IN_MASK))
-
-/* Start Enable Pin Interrupts - table 58 page 66 */
-
-#define SE_PIN_BASE_INT 32
-
-#define SE_U7_RX_INT 63
-#define SE_U7_HCTS_INT 62
-#define SE_BT_CLKREQ_INT 61
-#define SE_U6_IRRX_INT 60
-/*59 unused*/
-#define SE_U5_RX_INT 58
-#define SE_GPI_11_INT 57
-#define SE_U3_RX_INT 56
-#define SE_U2_HCTS_INT 55
-#define SE_U2_RX_INT 54
-#define SE_U1_RX_INT 53
-#define SE_DISP_SYNC_INT 52
-/*51 unused*/
-#define SE_SDIO_INT_N 50
-#define SE_MSDIO_START_INT 49
-#define SE_GPI_06_INT 48
-#define SE_GPI_05_INT 47
-#define SE_GPI_04_INT 46
-#define SE_GPI_03_INT 45
-#define SE_GPI_02_INT 44
-#define SE_GPI_01_INT 43
-#define SE_GPI_00_INT 42
-#define SE_SYSCLKEN_PIN_INT 41
-#define SE_SPI1_DATAIN_INT 40
-#define SE_GPI_07_INT 39
-#define SE_SPI2_DATAIN_INT 38
-#define SE_GPI_10_INT 37
-#define SE_GPI_09_INT 36
-#define SE_GPI_08_INT 35
-/*34-32 unused*/
-
-/* Start Enable Internal Interrupts - table 57 page 65 */
-
-#define SE_INT_BASE_INT 0
-
-#define SE_TS_IRQ 31
-#define SE_TS_P_INT 30
-#define SE_TS_AUX_INT 29
-/*27-28 unused*/
-#define SE_USB_AHB_NEED_CLK_INT 26
-#define SE_MSTIMER_INT 25
-#define SE_RTC_INT 24
-#define SE_USB_NEED_CLK_INT 23
-#define SE_USB_INT 22
-#define SE_USB_I2C_INT 21
-#define SE_USB_OTG_TIMER_INT 20
-#define SE_USB_OTG_ATX_INT_N 19
-/*18 unused*/
-#define SE_DSP_GPIO4_INT 17
-#define SE_KEY_IRQ 16
-#define SE_DSP_SLAVEPORT_INT 15
-#define SE_DSP_GPIO1_INT 14
-#define SE_DSP_GPIO0_INT 13
-#define SE_DSP_AHB_INT 12
-/*11-6 unused*/
-#define SE_GPIO_05_INT 5
-#define SE_GPIO_04_INT 4
-#define SE_GPIO_03_INT 3
-#define SE_GPIO_02_INT 2
-#define SE_GPIO_01_INT 1
-#define SE_GPIO_00_INT 0
-
-#define START_INT_REG_BIT(irq) (1<<((irq)&0x1F))
-
-#define START_INT_ER_REG(irq) IO_ADDRESS((PNX4008_PWRMAN_BASE + 0x20 + (((irq)&(0x1<<5))>>1)))
-#define START_INT_RSR_REG(irq) IO_ADDRESS((PNX4008_PWRMAN_BASE + 0x24 + (((irq)&(0x1<<5))>>1)))
-#define START_INT_SR_REG(irq) IO_ADDRESS((PNX4008_PWRMAN_BASE + 0x28 + (((irq)&(0x1<<5))>>1)))
-#define START_INT_APR_REG(irq) IO_ADDRESS((PNX4008_PWRMAN_BASE + 0x2C + (((irq)&(0x1<<5))>>1)))
-
-extern int pnx4008_gpio_register_pin(unsigned short pin);
-extern int pnx4008_gpio_unregister_pin(unsigned short pin);
-extern unsigned long pnx4008_gpio_read_pin(unsigned short pin);
-extern int pnx4008_gpio_write_pin(unsigned short pin, int output);
-extern int pnx4008_gpio_set_pin_direction(unsigned short pin, int output);
-extern int pnx4008_gpio_read_pin_direction(unsigned short pin);
-extern int pnx4008_gpio_set_pin_mux(unsigned short pin, int output);
-extern int pnx4008_gpio_read_pin_mux(unsigned short pin);
-
-static inline void start_int_umask(u8 irq)
-{
- __raw_writel(__raw_readl(START_INT_ER_REG(irq)) |
- START_INT_REG_BIT(irq), START_INT_ER_REG(irq));
-}
-
-static inline void start_int_mask(u8 irq)
-{
- __raw_writel(__raw_readl(START_INT_ER_REG(irq)) &
- ~START_INT_REG_BIT(irq), START_INT_ER_REG(irq));
-}
-
-static inline void start_int_ack(u8 irq)
-{
- __raw_writel(START_INT_REG_BIT(irq), START_INT_RSR_REG(irq));
-}
-
-static inline void start_int_set_falling_edge(u8 irq)
-{
- __raw_writel(__raw_readl(START_INT_APR_REG(irq)) &
- ~START_INT_REG_BIT(irq), START_INT_APR_REG(irq));
-}
-
-static inline void start_int_set_rising_edge(u8 irq)
-{
- __raw_writel(__raw_readl(START_INT_APR_REG(irq)) |
- START_INT_REG_BIT(irq), START_INT_APR_REG(irq));
-}
-
-#endif /* _PNX4008_GPIO_H_ */
@@ -1,32 +0,0 @@
-/*
- * arch/arm/mach-pnx4008/include/mach/hardware.h
- *
- * Copyright (c) 2005 MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-#ifndef __ASM_ARCH_HARDWARE_H
-#define __ASM_ARCH_HARDWARE_H
-
-#include <asm/sizes.h>
-#include <mach/platform.h>
-
-/* Start of virtual addresses for IO devices */
-#define IO_BASE 0xF0000000
-
-/* This macro relies on fact that for all HW i/o addresses bits 20-23 are 0 */
-#define IO_ADDRESS(x) (((((x) & 0xff000000) >> 4) | ((x) & 0xfffff)) | IO_BASE)
-
-#endif
@@ -1,42 +0,0 @@
-/*
- * arch/arm/mach-pnx4008/include/mach/irq.h
- *
- * PNX4008 IRQ controller driver - header file
- * this one is used in entry-arnv.S as well so it cannot contain C code
- *
- * Copyright (c) 2005 Philips Semiconductors
- * Copyright (c) 2005 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-#ifndef __PNX4008_IRQ_H__
-#define __PNX4008_IRQ_H__
-
-#define MIC_VA_BASE IO_ADDRESS(PNX4008_INTCTRLMIC_BASE)
-#define SIC1_VA_BASE IO_ADDRESS(PNX4008_INTCTRLSIC1_BASE)
-#define SIC2_VA_BASE IO_ADDRESS(PNX4008_INTCTRLSIC2_BASE)
-
-/* Manual: Chapter 20, page 195 */
-
-#define INTC_BIT(irq) (1<< ((irq) & 0x1F))
-
-#define INTC_ER(irq) IO_ADDRESS((PNX4008_INTCTRLMIC_BASE + 0x0 + (((irq)&(0x3<<5))<<9)))
-#define INTC_RSR(irq) IO_ADDRESS((PNX4008_INTCTRLMIC_BASE + 0x4 + (((irq)&(0x3<<5))<<9)))
-#define INTC_SR(irq) IO_ADDRESS((PNX4008_INTCTRLMIC_BASE + 0x8 + (((irq)&(0x3<<5))<<9)))
-#define INTC_APR(irq) IO_ADDRESS((PNX4008_INTCTRLMIC_BASE + 0xC + (((irq)&(0x3<<5))<<9)))
-#define INTC_ATR(irq) IO_ADDRESS((PNX4008_INTCTRLMIC_BASE + 0x10 + (((irq)&(0x3<<5))<<9)))
-#define INTC_ITR(irq) IO_ADDRESS((PNX4008_INTCTRLMIC_BASE + 0x14 + (((irq)&(0x3<<5))<<9)))
-
-#define START_INT_REG_BIT(irq) (1<<((irq)&0x1F))
-
-#define START_INT_ER_REG(irq) IO_ADDRESS((PNX4008_PWRMAN_BASE + 0x20 + (((irq)&(0x1<<5))>>1)))
-#define START_INT_RSR_REG(irq) IO_ADDRESS((PNX4008_PWRMAN_BASE + 0x24 + (((irq)&(0x1<<5))>>1)))
-#define START_INT_SR_REG(irq) IO_ADDRESS((PNX4008_PWRMAN_BASE + 0x28 + (((irq)&(0x1<<5))>>1)))
-#define START_INT_APR_REG(irq) IO_ADDRESS((PNX4008_PWRMAN_BASE + 0x2C + (((irq)&(0x1<<5))>>1)))
-
-extern void __init pnx4008_init_irq(void);
-
-#endif /* __PNX4008_IRQ_H__ */
@@ -1,215 +0,0 @@
-/*
- * arch/arm/mach-pnx4008/include/mach/irqs.h
- *
- * PNX4008 IRQ controller driver - header file
- *
- * Author: Dmitry Chigirev <source@mvista.com>
- *
- * 2005 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-#ifndef __PNX4008_IRQS_h__
-#define __PNX4008_IRQS_h__
-
-#define NR_IRQS 96
-
-/*Manual: table 259, page 199*/
-
-/*SUB2 Interrupt Routing (SIC2)*/
-
-#define SIC2_BASE_INT 64
-
-#define CLK_SWITCH_ARM_INT 95 /*manual: Clkswitch ARM */
-#define CLK_SWITCH_DSP_INT 94 /*manual: ClkSwitch DSP */
-#define CLK_SWITCH_AUD_INT 93 /*manual: Clkswitch AUD */
-#define GPI_06_INT 92
-#define GPI_05_INT 91
-#define GPI_04_INT 90
-#define GPI_03_INT 89
-#define GPI_02_INT 88
-#define GPI_01_INT 87
-#define GPI_00_INT 86
-#define BT_CLKREQ_INT 85
-#define SPI1_DATIN_INT 84
-#define U5_RX_INT 83
-#define SDIO_INT_N 82
-#define CAM_HS_INT 81
-#define CAM_VS_INT 80
-#define GPI_07_INT 79
-#define DISP_SYNC_INT 78
-#define DSP_INT8 77
-#define U7_HCTS_INT 76
-#define GPI_10_INT 75
-#define GPI_09_INT 74
-#define GPI_08_INT 73
-#define DSP_INT7 72
-#define U2_HCTS_INT 71
-#define SPI2_DATIN_INT 70
-#define GPIO_05_INT 69
-#define GPIO_04_INT 68
-#define GPIO_03_INT 67
-#define GPIO_02_INT 66
-#define GPIO_01_INT 65
-#define GPIO_00_INT 64
-
-/*Manual: table 258, page 198*/
-
-/*SUB1 Interrupt Routing (SIC1)*/
-
-#define SIC1_BASE_INT 32
-
-#define USB_I2C_INT 63
-#define USB_DEV_HP_INT 62
-#define USB_DEV_LP_INT 61
-#define USB_DEV_DMA_INT 60
-#define USB_HOST_INT 59
-#define USB_OTG_ATX_INT_N 58
-#define USB_OTG_TIMER_INT 57
-#define SW_INT 56
-#define SPI1_INT 55
-#define KEY_IRQ 54
-#define DSP_M_INT 53
-#define RTC_INT 52
-#define I2C_1_INT 51
-#define I2C_2_INT 50
-#define PLL1_LOCK_INT 49
-#define PLL2_LOCK_INT 48
-#define PLL3_LOCK_INT 47
-#define PLL4_LOCK_INT 46
-#define PLL5_LOCK_INT 45
-#define SPI2_INT 44
-#define DSP_INT1 43
-#define DSP_INT2 42
-#define DSP_TDM_INT2 41
-#define TS_AUX_INT 40
-#define TS_IRQ 39
-#define TS_P_INT 38
-#define UOUT1_TO_PAD_INT 37
-#define GPI_11_INT 36
-#define DSP_INT4 35
-#define JTAG_COMM_RX_INT 34
-#define JTAG_COMM_TX_INT 33
-#define DSP_INT3 32
-
-/*Manual: table 257, page 197*/
-
-/*MAIN Interrupt Routing*/
-
-#define MAIN_BASE_INT 0
-
-#define SUB2_FIQ_N 31 /*active low */
-#define SUB1_FIQ_N 30 /*active low */
-#define JPEG_INT 29
-#define DMA_INT 28
-#define MSTIMER_INT 27
-#define IIR1_INT 26
-#define IIR2_INT 25
-#define IIR7_INT 24
-#define DSP_TDM_INT0 23
-#define DSP_TDM_INT1 22
-#define DSP_P_INT 21
-#define DSP_INT0 20
-#define DUM_INT 19
-#define UOUT0_TO_PAD_INT 18
-#define MP4_ENC_INT 17
-#define MP4_DEC_INT 16
-#define SD0_INT 15
-#define MBX_INT 14
-#define SD1_INT 13
-#define MS_INT_N 12
-#define FLASH_INT 11 /*NAND*/
-#define IIR6_INT 10
-#define IIR5_INT 9
-#define IIR4_INT 8
-#define IIR3_INT 7
-#define WATCH_INT 6
-#define HSTIMER_INT 5
-#define ARCH_TIMER_IRQ HSTIMER_INT
-#define CAM_INT 4
-#define PRNG_INT 3
-#define CRYPTO_INT 2
-#define SUB2_IRQ_N 1 /*active low */
-#define SUB1_IRQ_N 0 /*active low */
-
-#define PNX4008_IRQ_TYPES \
-{ /*IRQ #'s: */ \
-IRQ_TYPE_LEVEL_LOW, IRQ_TYPE_LEVEL_LOW, IRQ_TYPE_LEVEL_LOW, IRQ_TYPE_LEVEL_HIGH, /* 0, 1, 2, 3 */ \
-IRQ_TYPE_LEVEL_LOW, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, /* 4, 5, 6, 7 */ \
-IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, /* 8, 9,10,11 */ \
-IRQ_TYPE_LEVEL_LOW, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, /* 12,13,14,15 */ \
-IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, /* 16,17,18,19 */ \
-IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, /* 20,21,22,23 */ \
-IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, /* 24,25,26,27 */ \
-IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_LOW, IRQ_TYPE_LEVEL_LOW, /* 28,29,30,31 */ \
-IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_LOW, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, /* 32,33,34,35 */ \
-IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_EDGE_FALLING, IRQ_TYPE_LEVEL_HIGH, /* 36,37,38,39 */ \
-IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, /* 40,41,42,43 */ \
-IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, /* 44,45,46,47 */ \
-IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_LOW, IRQ_TYPE_LEVEL_LOW, /* 48,49,50,51 */ \
-IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, /* 52,53,54,55 */ \
-IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_LOW, IRQ_TYPE_LEVEL_HIGH, /* 56,57,58,59 */ \
-IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, /* 60,61,62,63 */ \
-IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, /* 64,65,66,67 */ \
-IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, /* 68,69,70,71 */ \
-IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, /* 72,73,74,75 */ \
-IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, /* 76,77,78,79 */ \
-IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, /* 80,81,82,83 */ \
-IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, /* 84,85,86,87 */ \
-IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, /* 88,89,90,91 */ \
-IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_LEVEL_HIGH, /* 92,93,94,95 */ \
-}
-
-/* Start Enable Pin Interrupts - table 58 page 66 */
-
-#define SE_PIN_BASE_INT 32
-
-#define SE_U7_RX_INT 63
-#define SE_U7_HCTS_INT 62
-#define SE_BT_CLKREQ_INT 61
-#define SE_U6_IRRX_INT 60
-/*59 unused*/
-#define SE_U5_RX_INT 58
-#define SE_GPI_11_INT 57
-#define SE_U3_RX_INT 56
-#define SE_U2_HCTS_INT 55
-#define SE_U2_RX_INT 54
-#define SE_U1_RX_INT 53
-#define SE_DISP_SYNC_INT 52
-/*51 unused*/
-#define SE_SDIO_INT_N 50
-#define SE_MSDIO_START_INT 49
-#define SE_GPI_06_INT 48
-#define SE_GPI_05_INT 47
-#define SE_GPI_04_INT 46
-#define SE_GPI_03_INT 45
-#define SE_GPI_02_INT 44
-#define SE_GPI_01_INT 43
-#define SE_GPI_00_INT 42
-#define SE_SYSCLKEN_PIN_INT 41
-#define SE_SPI1_DATAIN_INT 40
-#define SE_GPI_07_INT 39
-#define SE_SPI2_DATAIN_INT 38
-#define SE_GPI_10_INT 37
-#define SE_GPI_09_INT 36
-#define SE_GPI_08_INT 35
-/*34-32 unused*/
-
-/* Start Enable Internal Interrupts - table 57 page 65 */
-
-#define SE_INT_BASE_INT 0
-
-#define SE_TS_IRQ 31
-#define SE_TS_P_INT 30
-#define SE_TS_AUX_INT 29
-/*27-28 unused*/
-#define SE_USB_AHB_NEED_CLK_INT 26
-#define SE_MSTIMER_INT 25
-#define SE_RTC_INT 24
-#define SE_USB_NEED_CLK_INT 23
-#define SE_USB_INT 22
-#define SE_USB_I2C_INT 21
-#define SE_USB_OTG_TIMER_INT 20
-
-#endif /* __PNX4008_IRQS_h__ */
@@ -1,21 +0,0 @@
-/*
- * arch/arm/mach-pnx4008/include/mach/param.h
- *
- * Copyright (C) 1999 ARM Limited
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#define HZ 100
@@ -1,69 +0,0 @@
-/*
- * arch/arm/mach-pnx4008/include/mach/platform.h
- *
- * PNX4008 Base addresses - header file
- *
- * Author: Dmitry Chigirev <source@mvista.com>
- *
- * Based on reference code received from Philips:
- * Copyright (C) 2003 Philips Semiconductors
- *
- * 2005 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-
-
-#ifndef __ASM_ARCH_PLATFORM_H__
-#define __ASM_ARCH_PLATFORM_H__
-
-#define PNX4008_IRAM_BASE 0x08000000
-#define PNX4008_IRAM_SIZE 0x00010000
-#define PNX4008_YUV_SLAVE_BASE 0x10000000
-#define PNX4008_DUM_SLAVE_BASE 0x18000000
-#define PNX4008_NDF_FLASH_BASE 0x20020000
-#define PNX4008_SPI1_BASE 0x20088000
-#define PNX4008_SPI2_BASE 0x20090000
-#define PNX4008_SD_CONFIG_BASE 0x20098000
-#define PNX4008_FLASH_DATA 0x200B0000
-#define PNX4008_MLC_FLASH_BASE 0x200B8000
-#define PNX4008_JPEG_CONFIG_BASE 0x300A0000
-#define PNX4008_DMA_CONFIG_BASE 0x31000000
-#define PNX4008_USB_CONFIG_BASE 0x31020000
-#define PNX4008_SDRAM_CFG_BASE 0x31080000
-#define PNX4008_AHB2FAB_BASE 0x40000000
-#define PNX4008_PWRMAN_BASE 0x40004000
-#define PNX4008_INTCTRLMIC_BASE 0x40008000
-#define PNX4008_INTCTRLSIC1_BASE 0x4000C000
-#define PNX4008_INTCTRLSIC2_BASE 0x40010000
-#define PNX4008_HSUART1_BASE 0x40014000
-#define PNX4008_HSUART2_BASE 0x40018000
-#define PNX4008_HSUART7_BASE 0x4001C000
-#define PNX4008_RTC_BASE 0x40024000
-#define PNX4008_PIO_BASE 0x40028000
-#define PNX4008_MSTIMER_BASE 0x40034000
-#define PNX4008_HSTIMER_BASE 0x40038000
-#define PNX4008_WDOG_BASE 0x4003C000
-#define PNX4008_DEBUG_BASE 0x40040000
-#define PNX4008_TOUCH1_BASE 0x40048000
-#define PNX4008_KEYSCAN_BASE 0x40050000
-#define PNX4008_UARTCTRL_BASE 0x40054000
-#define PNX4008_PWM_BASE 0x4005C000
-#define PNX4008_UART3_BASE 0x40080000
-#define PNX4008_UART4_BASE 0x40088000
-#define PNX4008_UART5_BASE 0x40090000
-#define PNX4008_UART6_BASE 0x40098000
-#define PNX4008_I2C1_BASE 0x400A0000
-#define PNX4008_I2C2_BASE 0x400A8000
-#define PNX4008_MAGICGATE_BASE 0x400B0000
-#define PNX4008_DUMCONF_BASE 0x400B8000
-#define PNX4008_DUM_MAINCFG_BASE 0x400BC000
-#define PNX4008_DSP_BASE 0x400C0000
-#define PNX4008_PROFCOUNTER_BASE 0x400C8000
-#define PNX4008_CRYPTO_BASE 0x400D0000
-#define PNX4008_CAMIFCONF_BASE 0x400D8000
-#define PNX4008_YUV2RGB_BASE 0x400E0000
-#define PNX4008_AUDIOCONFIG_BASE 0x400E8000
-
-#endif
@@ -1,33 +0,0 @@
-/*
- * arch/arm/mach-pnx4008/include/mach/pm.h
- *
- * PNX4008 Power Management Routiness - header file
- *
- * Authors: Vitaly Wool, Dmitry Chigirev <source@mvista.com>
- *
- * 2005 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-
-#ifndef __ASM_ARCH_PNX4008_PM_H
-#define __ASM_ARCH_PNX4008_PM_H
-
-#ifndef __ASSEMBLER__
-#include "irq.h"
-#include "irqs.h"
-#include "clock.h"
-
-extern void pnx4008_pm_idle(void);
-extern void pnx4008_pm_suspend(void);
-extern unsigned int pnx4008_cpu_suspend_sz;
-extern void pnx4008_cpu_suspend(void);
-extern unsigned int pnx4008_cpu_standby_sz;
-extern void pnx4008_cpu_standby(void);
-
-extern int pnx4008_startup_pll(struct clk *);
-extern int pnx4008_shutdown_pll(struct clk *);
-
-#endif /* ASSEMBLER */
-#endif /* __ASM_ARCH_PNX4008_PM_H */
@@ -1,19 +0,0 @@
-/*
- * arch/arm/mach-pnx4008/include/mach/timex.h
- *
- * PNX4008 timers header file
- *
- * Author: Dmitry Chigirev <source@mvista.com>
- *
- * 2005 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-
-#ifndef __PNX4008_TIMEX_H
-#define __PNX4008_TIMEX_H
-
-#define CLOCK_TICK_RATE 1000000
-
-#endif
@@ -1,46 +0,0 @@
-/*
- * arch/arm/mach-pnx4008/include/mach/uncompress.h
- *
- * Copyright (C) 1999 ARM Limited
- * Copyright (C) 2006 MontaVista Software, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#define UART5_BASE 0x40090000
-
-#define UART5_DR (*(volatile unsigned char *) (UART5_BASE))
-#define UART5_FR (*(volatile unsigned char *) (UART5_BASE + 18))
-
-static __inline__ void putc(char c)
-{
- while (UART5_FR & (1 << 5))
- barrier();
-
- UART5_DR = c;
-}
-
-/*
- * This does not append a newline
- */
-static inline void flush(void)
-{
-}
-
-/*
- * nothing to do
- */
-#define arch_decomp_setup()
-#define arch_decomp_wdog()
@@ -1,121 +0,0 @@
-/*
- * arch/arm/mach-pnx4008/irq.c
- *
- * PNX4008 IRQ controller driver
- *
- * Author: Dmitry Chigirev <source@mvista.com>
- *
- * Based on reference code received from Philips:
- * Copyright (C) 2003 Philips Semiconductors
- *
- * 2005 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/mm.h>
-#include <linux/interrupt.h>
-#include <linux/list.h>
-#include <linux/init.h>
-#include <linux/ioport.h>
-#include <linux/device.h>
-#include <linux/irq.h>
-#include <linux/io.h>
-#include <mach/hardware.h>
-#include <asm/setup.h>
-#include <asm/pgtable.h>
-#include <asm/page.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/map.h>
-#include <mach/irq.h>
-
-static u8 pnx4008_irq_type[NR_IRQS] = PNX4008_IRQ_TYPES;
-
-static void pnx4008_mask_irq(struct irq_data *d)
-{
- __raw_writel(__raw_readl(INTC_ER(d->irq)) & ~INTC_BIT(d->irq), INTC_ER(d->irq)); /* mask interrupt */
-}
-
-static void pnx4008_unmask_irq(struct irq_data *d)
-{
- __raw_writel(__raw_readl(INTC_ER(d->irq)) | INTC_BIT(d->irq), INTC_ER(d->irq)); /* unmask interrupt */
-}
-
-static void pnx4008_mask_ack_irq(struct irq_data *d)
-{
- __raw_writel(__raw_readl(INTC_ER(d->irq)) & ~INTC_BIT(d->irq), INTC_ER(d->irq)); /* mask interrupt */
- __raw_writel(INTC_BIT(d->irq), INTC_SR(d->irq)); /* clear interrupt status */
-}
-
-static int pnx4008_set_irq_type(struct irq_data *d, unsigned int type)
-{
- switch (type) {
- case IRQ_TYPE_EDGE_RISING:
- __raw_writel(__raw_readl(INTC_ATR(d->irq)) | INTC_BIT(d->irq), INTC_ATR(d->irq)); /*edge sensitive */
- __raw_writel(__raw_readl(INTC_APR(d->irq)) | INTC_BIT(d->irq), INTC_APR(d->irq)); /*rising edge */
- irq_set_handler(d->irq, handle_edge_irq);
- break;
- case IRQ_TYPE_EDGE_FALLING:
- __raw_writel(__raw_readl(INTC_ATR(d->irq)) | INTC_BIT(d->irq), INTC_ATR(d->irq)); /*edge sensitive */
- __raw_writel(__raw_readl(INTC_APR(d->irq)) & ~INTC_BIT(d->irq), INTC_APR(d->irq)); /*falling edge */
- irq_set_handler(d->irq, handle_edge_irq);
- break;
- case IRQ_TYPE_LEVEL_LOW:
- __raw_writel(__raw_readl(INTC_ATR(d->irq)) & ~INTC_BIT(d->irq), INTC_ATR(d->irq)); /*level sensitive */
- __raw_writel(__raw_readl(INTC_APR(d->irq)) & ~INTC_BIT(d->irq), INTC_APR(d->irq)); /*low level */
- irq_set_handler(d->irq, handle_level_irq);
- break;
- case IRQ_TYPE_LEVEL_HIGH:
- __raw_writel(__raw_readl(INTC_ATR(d->irq)) & ~INTC_BIT(d->irq), INTC_ATR(d->irq)); /*level sensitive */
- __raw_writel(__raw_readl(INTC_APR(d->irq)) | INTC_BIT(d->irq), INTC_APR(d->irq)); /* high level */
- irq_set_handler(d->irq, handle_level_irq);
- break;
-
- /* IRQ_TYPE_EDGE_BOTH is not supported */
- default:
- printk(KERN_ERR "PNX4008 IRQ: Unsupported irq type %d\n", type);
- return -1;
- }
- return 0;
-}
-
-static struct irq_chip pnx4008_irq_chip = {
- .irq_ack = pnx4008_mask_ack_irq,
- .irq_mask = pnx4008_mask_irq,
- .irq_unmask = pnx4008_unmask_irq,
- .irq_set_type = pnx4008_set_irq_type,
-};
-
-void __init pnx4008_init_irq(void)
-{
- unsigned int i;
-
- /* configure IRQ's */
- for (i = 0; i < NR_IRQS; i++) {
- set_irq_flags(i, IRQF_VALID);
- irq_set_chip(i, &pnx4008_irq_chip);
- pnx4008_set_irq_type(irq_get_irq_data(i), pnx4008_irq_type[i]);
- }
-
- /* configure and enable IRQ 0,1,30,31 (cascade interrupts) */
- pnx4008_set_irq_type(irq_get_irq_data(SUB1_IRQ_N),
- pnx4008_irq_type[SUB1_IRQ_N]);
- pnx4008_set_irq_type(irq_get_irq_data(SUB2_IRQ_N),
- pnx4008_irq_type[SUB2_IRQ_N]);
- pnx4008_set_irq_type(irq_get_irq_data(SUB1_FIQ_N),
- pnx4008_irq_type[SUB1_FIQ_N]);
- pnx4008_set_irq_type(irq_get_irq_data(SUB2_FIQ_N),
- pnx4008_irq_type[SUB2_FIQ_N]);
-
- /* mask all others */
- __raw_writel((1 << SUB2_FIQ_N) | (1 << SUB1_FIQ_N) |
- (1 << SUB2_IRQ_N) | (1 << SUB1_IRQ_N),
- INTC_ER(MAIN_BASE_INT));
- __raw_writel(0, INTC_ER(SIC1_BASE_INT));
- __raw_writel(0, INTC_ER(SIC2_BASE_INT));
-}
-
@@ -1,153 +0,0 @@
-/*
- * arch/arm/mach-pnx4008/pm.c
- *
- * Power Management driver for PNX4008
- *
- * Authors: Vitaly Wool, Dmitry Chigirev <source@mvista.com>
- *
- * 2005 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-
-#include <linux/pm.h>
-#include <linux/rtc.h>
-#include <linux/sched.h>
-#include <linux/proc_fs.h>
-#include <linux/suspend.h>
-#include <linux/delay.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/slab.h>
-
-#include <asm/cacheflush.h>
-
-#include <mach/hardware.h>
-#include <mach/pm.h>
-#include <mach/clock.h>
-
-#define SRAM_VA IO_ADDRESS(PNX4008_IRAM_BASE)
-
-static void *saved_sram;
-
-static struct clk *pll4_clk;
-
-static inline void pnx4008_standby(void)
-{
- void (*pnx4008_cpu_standby_ptr) (void);
-
- local_irq_disable();
- local_fiq_disable();
-
- clk_disable(pll4_clk);
-
- /*saving portion of SRAM to be used by suspend function. */
- memcpy(saved_sram, (void *)SRAM_VA, pnx4008_cpu_standby_sz);
-
- /*make sure SRAM copy gets physically written into SDRAM.
- SDRAM will be placed into self-refresh during power down */
- flush_cache_all();
-
- /*copy suspend function into SRAM */
- memcpy((void *)SRAM_VA, pnx4008_cpu_standby, pnx4008_cpu_standby_sz);
-
- /*do suspend */
- pnx4008_cpu_standby_ptr = (void *)SRAM_VA;
- pnx4008_cpu_standby_ptr();
-
- /*restoring portion of SRAM that was used by suspend function */
- memcpy((void *)SRAM_VA, saved_sram, pnx4008_cpu_standby_sz);
-
- clk_enable(pll4_clk);
-
- local_fiq_enable();
- local_irq_enable();
-}
-
-static inline void pnx4008_suspend(void)
-{
- void (*pnx4008_cpu_suspend_ptr) (void);
-
- local_irq_disable();
- local_fiq_disable();
-
- clk_disable(pll4_clk);
-
- __raw_writel(0xffffffff, START_INT_RSR_REG(SE_PIN_BASE_INT));
- __raw_writel(0xffffffff, START_INT_RSR_REG(SE_INT_BASE_INT));
-
- /*saving portion of SRAM to be used by suspend function. */
- memcpy(saved_sram, (void *)SRAM_VA, pnx4008_cpu_suspend_sz);
-
- /*make sure SRAM copy gets physically written into SDRAM.
- SDRAM will be placed into self-refresh during power down */
- flush_cache_all();
-
- /*copy suspend function into SRAM */
- memcpy((void *)SRAM_VA, pnx4008_cpu_suspend, pnx4008_cpu_suspend_sz);
-
- /*do suspend */
- pnx4008_cpu_suspend_ptr = (void *)SRAM_VA;
- pnx4008_cpu_suspend_ptr();
-
- /*restoring portion of SRAM that was used by suspend function */
- memcpy((void *)SRAM_VA, saved_sram, pnx4008_cpu_suspend_sz);
-
- clk_enable(pll4_clk);
-
- local_fiq_enable();
- local_irq_enable();
-}
-
-static int pnx4008_pm_enter(suspend_state_t state)
-{
- switch (state) {
- case PM_SUSPEND_STANDBY:
- pnx4008_standby();
- break;
- case PM_SUSPEND_MEM:
- pnx4008_suspend();
- break;
- }
- return 0;
-}
-
-static int pnx4008_pm_valid(suspend_state_t state)
-{
- return (state == PM_SUSPEND_STANDBY) ||
- (state == PM_SUSPEND_MEM);
-}
-
-static const struct platform_suspend_ops pnx4008_pm_ops = {
- .enter = pnx4008_pm_enter,
- .valid = pnx4008_pm_valid,
-};
-
-int __init pnx4008_pm_init(void)
-{
- u32 sram_size_to_allocate;
-
- pll4_clk = clk_get(0, "ck_pll4");
- if (IS_ERR(pll4_clk)) {
- printk(KERN_ERR
- "PM Suspend cannot acquire ARM(PLL4) clock control\n");
- return PTR_ERR(pll4_clk);
- }
-
- if (pnx4008_cpu_standby_sz > pnx4008_cpu_suspend_sz)
- sram_size_to_allocate = pnx4008_cpu_standby_sz;
- else
- sram_size_to_allocate = pnx4008_cpu_suspend_sz;
-
- saved_sram = kmalloc(sram_size_to_allocate, GFP_ATOMIC);
- if (!saved_sram) {
- printk(KERN_ERR
- "PM Suspend: cannot allocate memory to save portion of SRAM\n");
- clk_put(pll4_clk);
- return -ENOMEM;
- }
-
- suspend_set_ops(&pnx4008_pm_ops);
- return 0;
-}
@@ -1,67 +0,0 @@
-/*
- * linux/arch/arm/mach-pnx4008/serial.c
- *
- * PNX4008 UART initialization
- *
- * Copyright: MontaVista Software Inc. (c) 2005
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#include <linux/kernel.h>
-#include <linux/types.h>
-#include <linux/io.h>
-
-#include <mach/platform.h>
-#include <mach/hardware.h>
-
-#include <linux/serial_core.h>
-#include <linux/serial_reg.h>
-
-#include <mach/gpio-pnx4008.h>
-#include <mach/clock.h>
-
-#define UART_3 0
-#define UART_4 1
-#define UART_5 2
-#define UART_6 3
-#define UART_UNKNOWN (-1)
-
-#define UART3_BASE_VA IO_ADDRESS(PNX4008_UART3_BASE)
-#define UART4_BASE_VA IO_ADDRESS(PNX4008_UART4_BASE)
-#define UART5_BASE_VA IO_ADDRESS(PNX4008_UART5_BASE)
-#define UART6_BASE_VA IO_ADDRESS(PNX4008_UART6_BASE)
-
-#define UART_FCR_OFFSET 8
-#define UART_FIFO_SIZE 64
-
-void pnx4008_uart_init(void)
-{
- u32 tmp;
- int i = UART_FIFO_SIZE;
-
- __raw_writel(0xC1, UART5_BASE_VA + UART_FCR_OFFSET);
- __raw_writel(0xC1, UART3_BASE_VA + UART_FCR_OFFSET);
-
- /* Send a NULL to fix the UART HW bug */
- __raw_writel(0x00, UART5_BASE_VA);
- __raw_writel(0x00, UART3_BASE_VA);
-
- while (i--) {
- tmp = __raw_readl(UART5_BASE_VA);
- tmp = __raw_readl(UART3_BASE_VA);
- }
- __raw_writel(0, UART5_BASE_VA + UART_FCR_OFFSET);
- __raw_writel(0, UART3_BASE_VA + UART_FCR_OFFSET);
-
- /* setup wakeup interrupt */
- start_int_set_rising_edge(SE_U3_RX_INT);
- start_int_ack(SE_U3_RX_INT);
- start_int_umask(SE_U3_RX_INT);
-
- start_int_set_rising_edge(SE_U5_RX_INT);
- start_int_ack(SE_U5_RX_INT);
- start_int_umask(SE_U5_RX_INT);
-}
-
@@ -1,195 +0,0 @@
-/*
- * linux/arch/arm/mach-pnx4008/sleep.S
- *
- * PNX4008 support for STOP mode and SDRAM self-refresh
- *
- * Authors: Dmitry Chigirev, Vitaly Wool <source@mvista.com>
- *
- * 2005 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-
-#include <linux/linkage.h>
-#include <asm/assembler.h>
-#include <mach/hardware.h>
-
-#define PWRMAN_VA_BASE IO_ADDRESS(PNX4008_PWRMAN_BASE)
-#define PWR_CTRL_REG_OFFS 0x44
-
-#define SDRAM_CFG_VA_BASE IO_ADDRESS(PNX4008_SDRAM_CFG_BASE)
-#define MPMC_STATUS_REG_OFFS 0x4
-
- .text
-
-ENTRY(pnx4008_cpu_suspend)
- @this function should be entered in Direct run mode.
-
- @ save registers on stack
- stmfd sp!, {r0 - r6, lr}
-
- @ setup Power Manager base address in r4
- @ and put it's value in r5
- mov r4, #(PWRMAN_VA_BASE & 0xff000000)
- orr r4, r4, #(PWRMAN_VA_BASE & 0x00ff0000)
- orr r4, r4, #(PWRMAN_VA_BASE & 0x0000ff00)
- orr r4, r4, #(PWRMAN_VA_BASE & 0x000000ff)
- ldr r5, [r4, #PWR_CTRL_REG_OFFS]
-
- @ setup SDRAM controller base address in r2
- @ and put it's value in r3
- mov r2, #(SDRAM_CFG_VA_BASE & 0xff000000)
- orr r2, r2, #(SDRAM_CFG_VA_BASE & 0x00ff0000)
- orr r2, r2, #(SDRAM_CFG_VA_BASE & 0x0000ff00)
- orr r2, r2, #(SDRAM_CFG_VA_BASE & 0x000000ff)
- ldr r3, [r2, #MPMC_STATUS_REG_OFFS] @extra read - HW bug workaround
-
- @ clear SDRAM self-refresh bit latch
- and r5, r5, #(~(1 << 8))
- @ clear SDRAM self-refresh bit
- and r5, r5, #(~(1 << 9))
- str r5, [r4, #PWR_CTRL_REG_OFFS]
-
- @ do save current bit settings in r1
- mov r1, r5
-
- @ set SDRAM self-refresh bit
- orr r5, r5, #(1 << 9)
- str r5, [r4, #PWR_CTRL_REG_OFFS]
-
- @ set SDRAM self-refresh bit latch
- orr r5, r5, #(1 << 8)
- str r5, [r4, #PWR_CTRL_REG_OFFS]
-
- @ clear SDRAM self-refresh bit latch
- and r5, r5, #(~(1 << 8))
- str r5, [r4, #PWR_CTRL_REG_OFFS]
-
- @ clear SDRAM self-refresh bit
- and r5, r5, #(~(1 << 9))
- str r5, [r4, #PWR_CTRL_REG_OFFS]
-
- @ wait for SDRAM to get into self-refresh mode
-2: ldr r3, [r2, #MPMC_STATUS_REG_OFFS]
- tst r3, #(1 << 2)
- beq 2b
-
- @ to prepare SDRAM to get out of self-refresh mode after wakeup
- orr r5, r5, #(1 << 7)
- str r5, [r4, #PWR_CTRL_REG_OFFS]
-
- @ do enter stop mode
- orr r5, r5, #(1 << 0)
- str r5, [r4, #PWR_CTRL_REG_OFFS]
- nop
- nop
- nop
- nop
- nop
- nop
- nop
- nop
- nop
-
- @ sleeping now...
-
- @ coming out of STOP mode into Direct Run mode
- @ clear STOP mode and SDRAM self-refresh bits
- str r1, [r4, #PWR_CTRL_REG_OFFS]
-
- @ wait for SDRAM to get out self-refresh mode
-3: ldr r3, [r2, #MPMC_STATUS_REG_OFFS]
- tst r3, #5
- bne 3b
-
- @ restore regs and return
- ldmfd sp!, {r0 - r6, pc}
-
-ENTRY(pnx4008_cpu_suspend_sz)
- .word . - pnx4008_cpu_suspend
-
-ENTRY(pnx4008_cpu_standby)
- @ save registers on stack
- stmfd sp!, {r0 - r6, lr}
-
- @ setup Power Manager base address in r4
- @ and put it's value in r5
- mov r4, #(PWRMAN_VA_BASE & 0xff000000)
- orr r4, r4, #(PWRMAN_VA_BASE & 0x00ff0000)
- orr r4, r4, #(PWRMAN_VA_BASE & 0x0000ff00)
- orr r4, r4, #(PWRMAN_VA_BASE & 0x000000ff)
- ldr r5, [r4, #PWR_CTRL_REG_OFFS]
-
- @ setup SDRAM controller base address in r2
- @ and put it's value in r3
- mov r2, #(SDRAM_CFG_VA_BASE & 0xff000000)
- orr r2, r2, #(SDRAM_CFG_VA_BASE & 0x00ff0000)
- orr r2, r2, #(SDRAM_CFG_VA_BASE & 0x0000ff00)
- orr r2, r2, #(SDRAM_CFG_VA_BASE & 0x000000ff)
- ldr r3, [r2, #MPMC_STATUS_REG_OFFS] @extra read - HW bug workaround
-
- @ clear SDRAM self-refresh bit latch
- and r5, r5, #(~(1 << 8))
- @ clear SDRAM self-refresh bit
- and r5, r5, #(~(1 << 9))
- str r5, [r4, #PWR_CTRL_REG_OFFS]
-
- @ do save current bit settings in r1
- mov r1, r5
-
- @ set SDRAM self-refresh bit
- orr r5, r5, #(1 << 9)
- str r5, [r4, #PWR_CTRL_REG_OFFS]
-
- @ set SDRAM self-refresh bit latch
- orr r5, r5, #(1 << 8)
- str r5, [r4, #PWR_CTRL_REG_OFFS]
-
- @ clear SDRAM self-refresh bit latch
- and r5, r5, #(~(1 << 8))
- str r5, [r4, #PWR_CTRL_REG_OFFS]
-
- @ clear SDRAM self-refresh bit
- and r5, r5, #(~(1 << 9))
- str r5, [r4, #PWR_CTRL_REG_OFFS]
-
- @ wait for SDRAM to get into self-refresh mode
-2: ldr r3, [r2, #MPMC_STATUS_REG_OFFS]
- tst r3, #(1 << 2)
- beq 2b
-
- @ set 'get out of self-refresh mode after wakeup' bit
- orr r5, r5, #(1 << 7)
- str r5, [r4, #PWR_CTRL_REG_OFFS]
-
- mcr p15, 0, r0, c7, c0, 4 @ kinda sleeping now...
-
- @ set SDRAM self-refresh bit latch
- orr r5, r5, #(1 << 8)
- str r5, [r4, #PWR_CTRL_REG_OFFS]
-
- @ clear SDRAM self-refresh bit latch
- and r5, r5, #(~(1 << 8))
- str r5, [r4, #PWR_CTRL_REG_OFFS]
-
- @ wait for SDRAM to get out self-refresh mode
-3: ldr r3, [r2, #MPMC_STATUS_REG_OFFS]
- tst r3, #5
- bne 3b
-
- @ restore regs and return
- ldmfd sp!, {r0 - r6, pc}
-
-ENTRY(pnx4008_cpu_standby_sz)
- .word . - pnx4008_cpu_standby
-
-ENTRY(pnx4008_cache_clean_invalidate)
- stmfd sp!, {r0 - r6, lr}
-#ifdef CONFIG_CPU_DCACHE_WRITETHROUGH
- mcr p15, 0, ip, c7, c6, 0 @ invalidate D cache
-#else
-1: mrc p15, 0, r15, c7, c14, 3 @ test,clean,invalidate
- bne 1b
-#endif
- ldmfd sp!, {r0 - r6, pc}
@@ -1,134 +0,0 @@
-/*
- * arch/arm/mach-pnx4008/time.c
- *
- * PNX4008 Timers
- *
- * Authors: Vitaly Wool, Dmitry Chigirev, Grigory Tolstolytkin <source@mvista.com>
- *
- * 2005 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/interrupt.h>
-#include <linux/sched.h>
-#include <linux/spinlock.h>
-#include <linux/module.h>
-#include <linux/kallsyms.h>
-#include <linux/time.h>
-#include <linux/timex.h>
-#include <linux/irq.h>
-#include <linux/io.h>
-
-#include <mach/hardware.h>
-#include <asm/leds.h>
-#include <asm/mach/time.h>
-#include <asm/errno.h>
-
-#include "time.h"
-
-/*! Note: all timers are UPCOUNTING */
-
-/*!
- * Returns number of us since last clock interrupt. Note that interrupts
- * will have been disabled by do_gettimeoffset()
- */
-static unsigned long pnx4008_gettimeoffset(void)
-{
- u32 ticks_to_match =
- __raw_readl(HSTIM_MATCH0) - __raw_readl(HSTIM_COUNTER);
- u32 elapsed = LATCH - ticks_to_match;
- return (elapsed * (tick_nsec / 1000)) / LATCH;
-}
-
-/*!
- * IRQ handler for the timer
- */
-static irqreturn_t pnx4008_timer_interrupt(int irq, void *dev_id)
-{
- if (__raw_readl(HSTIM_INT) & MATCH0_INT) {
-
- do {
- timer_tick();
-
- /*
- * this algorithm takes care of possible delay
- * for this interrupt handling longer than a normal
- * timer period
- */
- __raw_writel(__raw_readl(HSTIM_MATCH0) + LATCH,
- HSTIM_MATCH0);
- __raw_writel(MATCH0_INT, HSTIM_INT); /* clear interrupt */
-
- /*
- * The goal is to keep incrementing HSTIM_MATCH0
- * register until HSTIM_MATCH0 indicates time after
- * what HSTIM_COUNTER indicates.
- */
- } while ((signed)
- (__raw_readl(HSTIM_MATCH0) -
- __raw_readl(HSTIM_COUNTER)) < 0);
- }
-
- return IRQ_HANDLED;
-}
-
-static struct irqaction pnx4008_timer_irq = {
- .name = "PNX4008 Tick Timer",
- .flags = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
- .handler = pnx4008_timer_interrupt
-};
-
-/*!
- * Set up timer and timer interrupt.
- */
-static __init void pnx4008_setup_timer(void)
-{
- __raw_writel(RESET_COUNT, MSTIM_CTRL);
- while (__raw_readl(MSTIM_COUNTER)) ; /* wait for reset to complete. 100% guarantee event */
- __raw_writel(0, MSTIM_CTRL); /* stop the timer */
- __raw_writel(0, MSTIM_MCTRL);
-
- __raw_writel(RESET_COUNT, HSTIM_CTRL);
- while (__raw_readl(HSTIM_COUNTER)) ; /* wait for reset to complete. 100% guarantee event */
- __raw_writel(0, HSTIM_CTRL);
- __raw_writel(0, HSTIM_MCTRL);
- __raw_writel(0, HSTIM_CCR);
- __raw_writel(12, HSTIM_PMATCH); /* scale down to 1 MHZ */
- __raw_writel(LATCH, HSTIM_MATCH0);
- __raw_writel(MR0_INT, HSTIM_MCTRL);
-
- setup_irq(HSTIMER_INT, &pnx4008_timer_irq);
-
- __raw_writel(COUNT_ENAB | DEBUG_EN, HSTIM_CTRL); /*start timer, stop when JTAG active */
-}
-
-/* Timer Clock Control in PM register */
-#define TIMCLK_CTRL_REG IO_ADDRESS((PNX4008_PWRMAN_BASE + 0xBC))
-#define WATCHDOG_CLK_EN 1
-#define TIMER_CLK_EN 2 /* HS and MS timers? */
-
-static u32 timclk_ctrl_reg_save;
-
-void pnx4008_timer_suspend(void)
-{
- timclk_ctrl_reg_save = __raw_readl(TIMCLK_CTRL_REG);
- __raw_writel(0, TIMCLK_CTRL_REG); /* disable timers */
-}
-
-void pnx4008_timer_resume(void)
-{
- __raw_writel(timclk_ctrl_reg_save, TIMCLK_CTRL_REG); /* enable timers */
-}
-
-struct sys_timer pnx4008_timer = {
- .init = pnx4008_setup_timer,
- .offset = pnx4008_gettimeoffset,
- .suspend = pnx4008_timer_suspend,
- .resume = pnx4008_timer_resume,
-};
-
@@ -1,70 +0,0 @@
-/*
- * arch/arm/mach-pnx4008/include/mach/timex.h
- *
- * PNX4008 timers header file
- *
- * Author: Dmitry Chigirev <source@mvista.com>
- *
- * 2005 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-#ifndef PNX_TIME_H
-#define PNX_TIME_H
-
-#include <linux/io.h>
-#include <mach/hardware.h>
-
-#define TICKS2USECS(x) (x)
-
-/* MilliSecond Timer - Chapter 21 Page 202 */
-
-#define MSTIM_INT IO_ADDRESS((PNX4008_MSTIMER_BASE + 0x0))
-#define MSTIM_CTRL IO_ADDRESS((PNX4008_MSTIMER_BASE + 0x4))
-#define MSTIM_COUNTER IO_ADDRESS((PNX4008_MSTIMER_BASE + 0x8))
-#define MSTIM_MCTRL IO_ADDRESS((PNX4008_MSTIMER_BASE + 0x14))
-#define MSTIM_MATCH0 IO_ADDRESS((PNX4008_MSTIMER_BASE + 0x18))
-#define MSTIM_MATCH1 IO_ADDRESS((PNX4008_MSTIMER_BASE + 0x1c))
-
-/* High Speed Timer - Chpater 22, Page 205 */
-
-#define HSTIM_INT IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x0))
-#define HSTIM_CTRL IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x4))
-#define HSTIM_COUNTER IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x8))
-#define HSTIM_PMATCH IO_ADDRESS((PNX4008_HSTIMER_BASE + 0xC))
-#define HSTIM_PCOUNT IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x10))
-#define HSTIM_MCTRL IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x14))
-#define HSTIM_MATCH0 IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x18))
-#define HSTIM_MATCH1 IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x1c))
-#define HSTIM_MATCH2 IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x20))
-#define HSTIM_CCR IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x28))
-#define HSTIM_CR0 IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x2C))
-#define HSTIM_CR1 IO_ADDRESS((PNX4008_HSTIMER_BASE + 0x30))
-
-/* IMPORTANT: both timers are UPCOUNTING */
-
-/* xSTIM_MCTRL bit definitions */
-#define MR0_INT 1
-#define RESET_COUNT0 (1<<1)
-#define STOP_COUNT0 (1<<2)
-#define MR1_INT (1<<3)
-#define RESET_COUNT1 (1<<4)
-#define STOP_COUNT1 (1<<5)
-#define MR2_INT (1<<6)
-#define RESET_COUNT2 (1<<7)
-#define STOP_COUNT2 (1<<8)
-
-/* xSTIM_CTRL bit definitions */
-#define COUNT_ENAB 1
-#define RESET_COUNT (1<<1)
-#define DEBUG_EN (1<<2)
-
-/* xSTIM_INT bit definitions */
-#define MATCH0_INT 1
-#define MATCH1_INT (1<<1)
-#define MATCH2_INT (1<<2)
-#define RTC_TICK0 (1<<4)
-#define RTC_TICK1 (1<<5)
-
-#endif
@@ -158,7 +158,6 @@ edb9315a MACH_EDB9315A EDB9315A 772
stargate2 MACH_STARGATE2 STARGATE2 774
intelmote2 MACH_INTELMOTE2 INTELMOTE2 775
trizeps4 MACH_TRIZEPS4 TRIZEPS4 776
-pnx4008 MACH_PNX4008 PNX4008 782
cpuat91 MACH_CPUAT91 CPUAT91 787
iq81340sc MACH_IQ81340SC IQ81340SC 799
iq81340mc MACH_IQ81340MC IQ81340MC 801
@@ -545,7 +545,7 @@ config I2C_PMCMSP
config I2C_PNX
tristate "I2C bus support for Philips PNX and NXP LPC targets"
- depends on ARCH_PNX4008 || ARCH_LPC32XX
+ depends on ARCH_LPC32XX
help
This driver supports the Philips IP3204 I2C IP block master and/or
slave controller
@@ -13,7 +13,6 @@ config USB_ARCH_HAS_OHCI
default y if PXA3xx
default y if ARCH_EP93XX
default y if ARCH_AT91
- default y if ARCH_PNX4008
default y if MFD_TC6393XB
default y if ARCH_W90X900
default y if ARCH_DAVINCI_DA8XX
@@ -292,7 +292,7 @@ config USB_OHCI_HCD
depends on USB && USB_ARCH_HAS_OHCI
select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3
select USB_OTG_UTILS if ARCH_OMAP
- select USB_ISP1301 if ARCH_LPC32XX || ARCH_PNX4008
+ select USB_ISP1301 if ARCH_LPC32XX
---help---
The Open Host Controller Interface (OHCI) is a standard for accessing
USB 1.1 host controller hardware. It does more in hardware than Intel's
@@ -1049,7 +1049,7 @@ MODULE_LICENSE ("GPL");
#define PLATFORM_DRIVER ohci_hcd_at91_driver
#endif
-#if defined(CONFIG_ARCH_PNX4008) || defined(CONFIG_ARCH_LPC32XX)
+#ifdef CONFIG_ARCH_LPC32XX
#include "ohci-nxp.c"
#define PLATFORM_DRIVER usb_hcd_nxp_driver
#endif
@@ -2,7 +2,6 @@
* driver for NXP USB Host devices
*
* Currently supported OHCI host devices:
- * - Philips PNX4008
* - NXP LPC32xx
*
* Authors: Dmitry Chigirev <source@mvista.com>
@@ -66,38 +65,6 @@ static struct clk *usb_pll_clk;
static struct clk *usb_dev_clk;
static struct clk *usb_otg_clk;
-static void isp1301_configure_pnx4008(void)
-{
- /* PNX4008 only supports DAT_SE0 USB mode */
- /* PNX4008 R2A requires setting the MAX603 to output 3.6V */
- /* Power up externel charge-pump */
-
- i2c_smbus_write_byte_data(isp1301_i2c_client,
- ISP1301_I2C_MODE_CONTROL_1, MC1_DAT_SE0 | MC1_SPEED_REG);
- i2c_smbus_write_byte_data(isp1301_i2c_client,
- ISP1301_I2C_MODE_CONTROL_1 | ISP1301_I2C_REG_CLEAR_ADDR,
- ~(MC1_DAT_SE0 | MC1_SPEED_REG));
- i2c_smbus_write_byte_data(isp1301_i2c_client,
- ISP1301_I2C_MODE_CONTROL_2,
- MC2_BI_DI | MC2_PSW_EN | MC2_SPD_SUSP_CTRL);
- i2c_smbus_write_byte_data(isp1301_i2c_client,
- ISP1301_I2C_MODE_CONTROL_2 | ISP1301_I2C_REG_CLEAR_ADDR,
- ~(MC2_BI_DI | MC2_PSW_EN | MC2_SPD_SUSP_CTRL));
- i2c_smbus_write_byte_data(isp1301_i2c_client,
- ISP1301_I2C_OTG_CONTROL_1, OTG1_DM_PULLDOWN | OTG1_DP_PULLDOWN);
- i2c_smbus_write_byte_data(isp1301_i2c_client,
- ISP1301_I2C_OTG_CONTROL_1 | ISP1301_I2C_REG_CLEAR_ADDR,
- ~(OTG1_DM_PULLDOWN | OTG1_DP_PULLDOWN));
- i2c_smbus_write_byte_data(isp1301_i2c_client,
- ISP1301_I2C_INTERRUPT_LATCH | ISP1301_I2C_REG_CLEAR_ADDR, 0xFF);
- i2c_smbus_write_byte_data(isp1301_i2c_client,
- ISP1301_I2C_INTERRUPT_FALLING | ISP1301_I2C_REG_CLEAR_ADDR,
- 0xFF);
- i2c_smbus_write_byte_data(isp1301_i2c_client,
- ISP1301_I2C_INTERRUPT_RISING | ISP1301_I2C_REG_CLEAR_ADDR,
- 0xFF);
-}
-
static void isp1301_configure_lpc32xx(void)
{
/* LPC32XX only supports DAT_SE0 USB mode */
@@ -149,10 +116,7 @@ static void isp1301_configure_lpc32xx(vo
static void isp1301_configure(void)
{
- if (machine_is_pnx4008())
- isp1301_configure_pnx4008();
- else
- isp1301_configure_lpc32xx();
+ isp1301_configure_lpc32xx();
}
static inline void isp1301_vbus_on(void)
@@ -241,47 +205,6 @@ static const struct hc_driver ohci_nxp_h
.start_port_reset = ohci_start_port_reset,
};
-static void nxp_set_usb_bits(void)
-{
- if (machine_is_pnx4008()) {
- start_int_set_falling_edge(SE_USB_OTG_ATX_INT_N);
- start_int_ack(SE_USB_OTG_ATX_INT_N);
- start_int_umask(SE_USB_OTG_ATX_INT_N);
-
- start_int_set_rising_edge(SE_USB_OTG_TIMER_INT);
- start_int_ack(SE_USB_OTG_TIMER_INT);
- start_int_umask(SE_USB_OTG_TIMER_INT);
-
- start_int_set_rising_edge(SE_USB_I2C_INT);
- start_int_ack(SE_USB_I2C_INT);
- start_int_umask(SE_USB_I2C_INT);
-
- start_int_set_rising_edge(SE_USB_INT);
- start_int_ack(SE_USB_INT);
- start_int_umask(SE_USB_INT);
-
- start_int_set_rising_edge(SE_USB_NEED_CLK_INT);
- start_int_ack(SE_USB_NEED_CLK_INT);
- start_int_umask(SE_USB_NEED_CLK_INT);
-
- start_int_set_rising_edge(SE_USB_AHB_NEED_CLK_INT);
- start_int_ack(SE_USB_AHB_NEED_CLK_INT);
- start_int_umask(SE_USB_AHB_NEED_CLK_INT);
- }
-}
-
-static void nxp_unset_usb_bits(void)
-{
- if (machine_is_pnx4008()) {
- start_int_mask(SE_USB_OTG_ATX_INT_N);
- start_int_mask(SE_USB_OTG_TIMER_INT);
- start_int_mask(SE_USB_I2C_INT);
- start_int_mask(SE_USB_INT);
- start_int_mask(SE_USB_NEED_CLK_INT);
- start_int_mask(SE_USB_AHB_NEED_CLK_INT);
- }
-}
-
static int __devinit usb_hcd_nxp_probe(struct platform_device *pdev)
{
struct usb_hcd *hcd = 0;
@@ -376,9 +299,6 @@ static int __devinit usb_hcd_nxp_probe(s
goto out8;
}
- /* Set all USB bits in the Start Enable register */
- nxp_set_usb_bits();
-
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!res) {
dev_err(&pdev->dev, "Failed to get MEM resource\n");
@@ -413,7 +333,6 @@ static int __devinit usb_hcd_nxp_probe(s
nxp_stop_hc();
out8:
- nxp_unset_usb_bits();
usb_put_hcd(hcd);
out7:
clk_disable(usb_otg_clk);
@@ -441,7 +360,6 @@ static int usb_hcd_nxp_remove(struct pla
nxp_stop_hc();
release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
usb_put_hcd(hcd);
- nxp_unset_usb_bits();
clk_disable(usb_pll_clk);
clk_put(usb_pll_clk);
clk_disable(usb_dev_clk);
@@ -237,12 +237,12 @@ config OMAP_WATCHDOG
here to enable the OMAP1610/OMAP1710/OMAP2420/OMAP3430/OMAP4430 watchdog timer.
config PNX4008_WATCHDOG
- tristate "PNX4008 and LPC32XX Watchdog"
- depends on ARCH_PNX4008 || ARCH_LPC32XX
+ tristate "LPC32XX Watchdog"
+ depends on ARCH_LPC32XX
select WATCHDOG_CORE
help
Say Y here if to include support for the watchdog timer
- in the PNX4008 or LPC32XX processor.
+ in the LPC32XX processor.
This driver can be built as a module by choosing M. The module
will be called pnx4008_wdt.
This patch removes the ARM architecture mach-pnx4008. No direct support or user feedback since 2006. Acknowledgements from NXP/Philips and Linux arm-soc maintainers. Signed-off-by: Roland Stigge <stigge@antcom.de> --- Changes since v1: * Removed removal of pnx4008 video driver, separated out into patch for video subsystem Applies to v3.6-rc3 arch/arm/Kconfig | 8 arch/arm/Makefile | 1 arch/arm/configs/pnx4008_defconfig | 472 --------- arch/arm/mach-pnx4008/Makefile | 12 arch/arm/mach-pnx4008/Makefile.boot | 4 arch/arm/mach-pnx4008/clock.c | 1001 ------------------- arch/arm/mach-pnx4008/clock.h | 43 arch/arm/mach-pnx4008/core.c | 290 ----- arch/arm/mach-pnx4008/dma.c | 1105 ---------------------- arch/arm/mach-pnx4008/gpio.c | 328 ------ arch/arm/mach-pnx4008/i2c.c | 86 - arch/arm/mach-pnx4008/include/mach/clock.h | 62 - arch/arm/mach-pnx4008/include/mach/debug-macro.S | 21 arch/arm/mach-pnx4008/include/mach/dma.h | 160 --- arch/arm/mach-pnx4008/include/mach/entry-macro.S | 116 -- arch/arm/mach-pnx4008/include/mach/gpio-pnx4008.h | 241 ---- arch/arm/mach-pnx4008/include/mach/hardware.h | 32 arch/arm/mach-pnx4008/include/mach/irq.h | 42 arch/arm/mach-pnx4008/include/mach/irqs.h | 215 ---- arch/arm/mach-pnx4008/include/mach/param.h | 21 arch/arm/mach-pnx4008/include/mach/platform.h | 69 - arch/arm/mach-pnx4008/include/mach/pm.h | 33 arch/arm/mach-pnx4008/include/mach/timex.h | 19 arch/arm/mach-pnx4008/include/mach/uncompress.h | 46 arch/arm/mach-pnx4008/irq.c | 121 -- arch/arm/mach-pnx4008/pm.c | 153 --- arch/arm/mach-pnx4008/serial.c | 67 - arch/arm/mach-pnx4008/sleep.S | 195 --- arch/arm/mach-pnx4008/time.c | 134 -- arch/arm/mach-pnx4008/time.h | 70 - arch/arm/tools/mach-types | 1 drivers/i2c/busses/Kconfig | 2 drivers/usb/Kconfig | 1 drivers/usb/host/Kconfig | 2 drivers/usb/host/ohci-hcd.c | 2 drivers/usb/host/ohci-nxp.c | 84 - drivers/watchdog/Kconfig | 6 37 files changed, 7 insertions(+), 5258 deletions(-)