@@ -13,37 +13,37 @@
#include <mach/kirkwood.h>
-#define CPU_CONFIG (BRIDGE_VIRT_BASE | 0x0100)
+#define CPU_CONFIG (BRIDGE_VIRT_BASE + 0x0100)
#define CPU_CONFIG_ERROR_PROP 0x00000004
-#define CPU_CONTROL (BRIDGE_VIRT_BASE | 0x0104)
+#define CPU_CONTROL (BRIDGE_VIRT_BASE + 0x0104)
#define CPU_RESET 0x00000002
-#define RSTOUTn_MASK (BRIDGE_VIRT_BASE | 0x0108)
+#define RSTOUTn_MASK (BRIDGE_VIRT_BASE + 0x0108)
#define WDT_RESET_OUT_EN 0x00000002
#define SOFT_RESET_OUT_EN 0x00000004
-#define SYSTEM_SOFT_RESET (BRIDGE_VIRT_BASE | 0x010c)
+#define SYSTEM_SOFT_RESET (BRIDGE_VIRT_BASE + 0x010c)
#define SOFT_RESET 0x00000001
-#define BRIDGE_CAUSE (BRIDGE_VIRT_BASE | 0x0110)
+#define BRIDGE_CAUSE (BRIDGE_VIRT_BASE + 0x0110)
#define WDT_INT_REQ 0x0008
#define BRIDGE_INT_TIMER1_CLR (~0x0004)
-#define IRQ_VIRT_BASE (BRIDGE_VIRT_BASE | 0x0200)
+#define IRQ_VIRT_BASE (BRIDGE_VIRT_BASE + 0x0200)
#define IRQ_CAUSE_LOW_OFF 0x0000
#define IRQ_MASK_LOW_OFF 0x0004
#define IRQ_CAUSE_HIGH_OFF 0x0010
#define IRQ_MASK_HIGH_OFF 0x0014
-#define TIMER_VIRT_BASE (BRIDGE_VIRT_BASE | 0x0300)
-#define TIMER_PHYS_BASE (BRIDGE_PHYS_BASE | 0x0300)
+#define TIMER_VIRT_BASE (BRIDGE_VIRT_BASE + 0x0300)
+#define TIMER_PHYS_BASE (BRIDGE_PHYS_BASE + 0x0300)
-#define L2_CONFIG_REG (BRIDGE_VIRT_BASE | 0x0128)
+#define L2_CONFIG_REG (BRIDGE_VIRT_BASE + 0x0128)
#define L2_WRITETHROUGH 0x00000010
-#define CLOCK_GATING_CTRL (BRIDGE_VIRT_BASE | 0x11c)
+#define CLOCK_GATING_CTRL (BRIDGE_VIRT_BASE + 0x11c)
#define CGC_BIT_GE0 (0)
#define CGC_BIT_PEX0 (2)
#define CGC_BIT_USB0 (3)
@@ -61,61 +61,61 @@
/*
* Register Map
*/
-#define DDR_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE | 0x00000)
-#define DDR_WINDOW_CPU_BASE (DDR_VIRT_BASE | 0x1500)
-#define DDR_OPERATION_BASE (DDR_VIRT_BASE | 0x1418)
-
-#define DEV_BUS_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x10000)
-#define DEV_BUS_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE | 0x10000)
-#define SAMPLE_AT_RESET (DEV_BUS_VIRT_BASE | 0x0030)
-#define DEVICE_ID (DEV_BUS_VIRT_BASE | 0x0034)
-#define GPIO_LOW_VIRT_BASE (DEV_BUS_VIRT_BASE | 0x0100)
-#define GPIO_HIGH_VIRT_BASE (DEV_BUS_VIRT_BASE | 0x0140)
-#define RTC_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x0300)
-#define SPI_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x0600)
-#define I2C_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x1000)
-#define UART0_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x2000)
-#define UART0_VIRT_BASE (DEV_BUS_VIRT_BASE | 0x2000)
-#define UART1_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x2100)
-#define UART1_VIRT_BASE (DEV_BUS_VIRT_BASE | 0x2100)
-
-#define BRIDGE_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE | 0x20000)
-#define BRIDGE_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x20000)
-
-#define CRYPTO_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x30000)
-
-#define PCIE_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE | 0x40000)
-#define PCIE_LINK_CTRL (PCIE_VIRT_BASE | 0x70)
-#define PCIE_STATUS (PCIE_VIRT_BASE | 0x1a04)
-#define PCIE1_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE | 0x44000)
-#define PCIE1_LINK_CTRL (PCIE1_VIRT_BASE | 0x70)
-#define PCIE1_STATUS (PCIE1_VIRT_BASE | 0x1a04)
-
-#define USB_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x50000)
-
-#define XOR0_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x60800)
-#define XOR0_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE | 0x60800)
-#define XOR1_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x60900)
-#define XOR1_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE | 0x60900)
-#define XOR0_HIGH_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x60A00)
-#define XOR0_HIGH_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE | 0x60A00)
-#define XOR1_HIGH_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x60B00)
-#define XOR1_HIGH_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE | 0x60B00)
-
-#define GE00_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x70000)
-#define GE01_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x74000)
-
-#define SATA_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x80000)
-#define SATA_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE | 0x80000)
-#define SATA0_IF_CTRL (SATA_VIRT_BASE | 0x2050)
-#define SATA0_PHY_MODE_2 (SATA_VIRT_BASE | 0x2330)
-#define SATA1_IF_CTRL (SATA_VIRT_BASE | 0x4050)
-#define SATA1_PHY_MODE_2 (SATA_VIRT_BASE | 0x4330)
-
-#define SDIO_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0x90000)
-
-#define AUDIO_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE | 0xA0000)
-#define AUDIO_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE | 0xA0000)
+#define DDR_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE + 0x00000)
+#define DDR_WINDOW_CPU_BASE (DDR_VIRT_BASE + 0x1500)
+#define DDR_OPERATION_BASE (DDR_VIRT_BASE + 0x1418)
+
+#define DEV_BUS_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE + 0x10000)
+#define DEV_BUS_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE + 0x10000)
+#define SAMPLE_AT_RESET (DEV_BUS_VIRT_BASE + 0x0030)
+#define DEVICE_ID (DEV_BUS_VIRT_BASE + 0x0034)
+#define GPIO_LOW_VIRT_BASE (DEV_BUS_VIRT_BASE + 0x0100)
+#define GPIO_HIGH_VIRT_BASE (DEV_BUS_VIRT_BASE + 0x0140)
+#define RTC_PHYS_BASE (DEV_BUS_PHYS_BASE + 0x0300)
+#define SPI_PHYS_BASE (DEV_BUS_PHYS_BASE + 0x0600)
+#define I2C_PHYS_BASE (DEV_BUS_PHYS_BASE + 0x1000)
+#define UART0_PHYS_BASE (DEV_BUS_PHYS_BASE + 0x2000)
+#define UART0_VIRT_BASE (DEV_BUS_VIRT_BASE + 0x2000)
+#define UART1_PHYS_BASE (DEV_BUS_PHYS_BASE + 0x2100)
+#define UART1_VIRT_BASE (DEV_BUS_VIRT_BASE + 0x2100)
+
+#define BRIDGE_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE + 0x20000)
+#define BRIDGE_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE + 0x20000)
+
+#define CRYPTO_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE + 0x30000)
+
+#define PCIE_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE + 0x40000)
+#define PCIE_LINK_CTRL (PCIE_VIRT_BASE + 0x70)
+#define PCIE_STATUS (PCIE_VIRT_BASE + 0x1a04)
+#define PCIE1_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE + 0x44000)
+#define PCIE1_LINK_CTRL (PCIE1_VIRT_BASE + 0x70)
+#define PCIE1_STATUS (PCIE1_VIRT_BASE + 0x1a04)
+
+#define USB_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE + 0x50000)
+
+#define XOR0_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE + 0x60800)
+#define XOR0_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE + 0x60800)
+#define XOR1_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE + 0x60900)
+#define XOR1_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE + 0x60900)
+#define XOR0_HIGH_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE + 0x60A00)
+#define XOR0_HIGH_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE + 0x60A00)
+#define XOR1_HIGH_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE + 0x60B00)
+#define XOR1_HIGH_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE + 0x60B00)
+
+#define GE00_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE + 0x70000)
+#define GE01_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE + 0x74000)
+
+#define SATA_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE + 0x80000)
+#define SATA_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE + 0x80000)
+#define SATA0_IF_CTRL (SATA_VIRT_BASE + 0x2050)
+#define SATA0_PHY_MODE_2 (SATA_VIRT_BASE + 0x2330)
+#define SATA1_IF_CTRL (SATA_VIRT_BASE + 0x4050)
+#define SATA1_PHY_MODE_2 (SATA_VIRT_BASE + 0x4330)
+
+#define SDIO_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE + 0x90000)
+
+#define AUDIO_PHYS_BASE (KIRKWOOD_REGS_PHYS_BASE + 0xA0000)
+#define AUDIO_VIRT_BASE (KIRKWOOD_REGS_VIRT_BASE + 0xA0000)
/*
* Supported devices and revisions.
Since we are going to use IOMEM() to define many base virtual addresses, we can no longer use binary or to define the individual register addresses ("binary or" arithmetic on pointers is not allowed). Instead, use the more conventional plus operator to do so. The binary or operators were actually not useful because the low-order bits of the base address were always zero, so the usage of the binary or operators was effectively identical to a plus operator. Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> --- arch/arm/mach-kirkwood/include/mach/bridge-regs.h | 20 ++-- arch/arm/mach-kirkwood/include/mach/kirkwood.h | 110 ++++++++++----------- 2 files changed, 65 insertions(+), 65 deletions(-)