@@ -22,6 +22,62 @@ Required properties for iomux controller:
- atmel,mux-mask: array of mask (periph per bank) to describe if a pin can be
configured in this periph mode. All the periph and bank need to be describe.
+How to create such array:
+
+Each column will represent the possible peripheral of the pinctrl
+Each line will represent a pio bank
+
+Take an example on the 9260
+Peripheral: 2 ( A and B)
+Bank: 3 (A, B and C)
+=>
+
+ /* A B */
+ 0xffffffff 0xffc00c3b /* pioA */
+ 0xffffffff 0x7fff3ccf /* pioB */
+ 0xffffffff 0x007fffff /* pioC */
+
+For each peripheral/bank we will descibe in a u32 if a pin can can be
+configured in it by putting 1 to the pin bit (1 << pin)
+
+Let's take the pioA on peripheral B
+From the datasheet Table 10-2.
+Peripheral B
+PA0 MCDB0
+PA1 MCCDB
+PA2
+PA3 MCDB3
+PA4 MCDB2
+PA5 MCDB1
+PA6
+PA7
+PA8
+PA9
+PA10 ETX2
+PA11 ETX3
+PA12
+PA13
+PA14
+PA15
+PA16
+PA17
+PA18
+PA19
+PA20
+PA21
+PA22 ETXER
+PA23 ETX2
+PA24 ETX3
+PA25 ERX2
+PA26 ERX3
+PA27 ERXCK
+PA28 ECRS
+PA29 ECOL
+PA30 RXD4
+PA31 TXD4
+
+=> 0xffc00c3b
+
Required properties for pin configuration node:
- atmel,pins: 4 integers array, represents a group of pins mux and config
setting. The format is atmel,pins = <PIN_BANK PIN_BANK_NUM PERIPH CONFIG>.
@@ -35,18 +91,14 @@ NOTE:
Some requirements for using atmel,at91rm9200-pinctrl binding:
1. We have pin function node defined under at91 controller node to represent
what pinmux functions this SoC supports.
-2. The pin configuration node intends to work on a specific function should
- to be defined under that specific function node.
- The function node's name should represent well about what function
- this group of pins in this pin configuration node are working on.
-3. The driver can use the function node's name and pin configuration node's
+2. The driver can use the function node's name and pin configuration node's
name describe the pin function and group hierarchy.
- For example, Linux Iat91 pinctrl driver takes the function node's name
+ For example, Linux at91 pinctrl driver takes the function node's name
as the function name and pin configuration node's name as group name to
create the map table.
-4. Each pin configuration node should have a phandle, devices can set pins
+3. Each pin configuration node should have a phandle, devices can set pins
configurations by referring to the phandle of that pin configuration node.
-5. The gpio controller must be describe in the pinctrl simple-bus.
+4. The gpio controller must be describe in the pinctrl simple-bus.
Examples:
@@ -103,6 +103,15 @@
compatible = "atmel,at91rm9200-pinctrl", "simple-bus";
ranges = <0xfffff400 0xfffff400 0x600>;
+ atmel,mux-mask = <
+ /* A B */
+ 0xffffffff 0xffc00c3b /* pioA */
+ 0xffffffff 0x7fff3ccf /* pioB */
+ 0xffffffff 0x007fffff /* pioC */
+ >;
+
+ /* shared pinctrl settings */
+
pioA: gpio@fffff400 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x200>;
@@ -94,6 +94,17 @@
compatible = "atmel,at91rm9200-pinctrl", "simple-bus";
ranges = <0xfffff200 0xfffff200 0xa00>;
+ atmel,mux-mask = <
+ /* A B */
+ 0xfffffffb 0xffffe07f /* pioA */
+ 0x0007ffff 0x39072fff /* pioB */
+ 0xffffffff 0x3ffffff8 /* pioC */
+ 0xfffffbff 0xffffffff /* pioD */
+ 0xffe00fff 0xfbfcff00 /* pioE */
+ >;
+
+ /* shared pinctrl settings */
+
pioA: gpio@fffff200 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff200 0x200>;
@@ -142,6 +153,7 @@
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
+ };
};
dbgu: serial@ffffee00 {
@@ -112,6 +112,17 @@
compatible = "atmel,at91rm9200-pinctrl", "simple-bus";
ranges = <0xfffff200 0xfffff200 0xa00>;
+ atmel,mux-mask = <
+ /* A B */
+ 0xffffffff 0xffc003ff /* pioA */
+ 0xffffffff 0x800f8f00 /* pioB */
+ 0xffffffff 0x00000e00 /* pioC */
+ 0xffffffff 0xff0c1381 /* pioD */
+ 0xffffffff 0x81ffff81 /* pioE */
+ >;
+
+ /* shared pinctrl settings */
+
pioA: gpio@fffff200 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff200 0x200>;
@@ -103,9 +103,19 @@
pinctrl@fffff400 {
#address-cells = <1>;
#size-cells = <1>;
- compatible = "atmel,at91rm9200-pinctrl", "simple-bus";
+ compatible = "atmel,at91sam9x5-pinctrl", "atmel,at91rm9200-pinctrl", "simple-bus";
ranges = <0xfffff400 0xfffff400 0x800>;
+ atmel,mux-mask = <
+ /* A B C */
+ 0xffffffff 0xffe07983 0x00000000 /* pioA */
+ 0x00040000 0x00047e0f 0x00000000 /* pioB */
+ 0xfdffffff 0x07c00000 0xb83fffff /* pioC */
+ 0x003fffff 0x003f8000 0x00000000 /* pioD */
+ >;
+
+ /* shared pinctrl settings */
+
pioA: gpio@fffff400 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x200>;
@@ -111,9 +111,19 @@
pinctrl@fffff200 {
#address-cells = <1>;
#size-cells = <1>;
- compatible = "atmel,at91rm9200-pinctrl", "simple-bus";
+ compatible = "atmel,at91sam9x5-pinctrl", "atmel,at91rm9200-pinctrl", "simple-bus";
ranges = <0xfffff400 0xfffff400 0x800>;
+ atmel,mux-mask = <
+ /* A B C */
+ 0xffffffff 0xffe0399f 0xc000001c /* pioA */
+ 0xffffffff 0xffc003ff 0xffc003ff /* pioB */
+ 0xffffffff 0xffc003ff 0xffc003ff /* pioC */
+ 0xffffffff 0xffc003ff 0xffc003ff /* pioD */
+ >;
+
+ /* shared pinctrl settings */
+
pioA: gpio@fffff400 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x200>;
@@ -111,6 +111,7 @@ CONFIG_I2C=y
CONFIG_I2C_GPIO=y
CONFIG_SPI=y
CONFIG_SPI_ATMEL=y
+CONFIG_PINCTRL_AT91=y
# CONFIG_HWMON is not set
CONFIG_WATCHDOG=y
CONFIG_AT91SAM9X_WATCHDOG=y
@@ -232,6 +232,9 @@ static struct clk_lookup periph_clocks_lookups[] = {
CLKDEV_CON_ID("pioA", &pioA_clk),
CLKDEV_CON_ID("pioB", &pioB_clk),
CLKDEV_CON_ID("pioC", &pioC_clk),
+ CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioA_clk),
+ CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioB_clk),
+ CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioC_clk),
};
static struct clk_lookup usart_clocks_lookups[] = {
@@ -210,6 +210,11 @@ static struct clk_lookup periph_clocks_lookups[] = {
CLKDEV_CON_DEV_ID("hclk", "a00000.ohci", &ohci_clk),
CLKDEV_CON_DEV_ID("spi_clk", "fffa4000.spi", &spi0_clk),
CLKDEV_CON_DEV_ID("spi_clk", "fffa8000.spi", &spi1_clk),
+ CLKDEV_CON_DEV_ID(NULL, "fffff200.gpio", &pioA_clk),
+ CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioB_clk),
+ CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioCDE_clk),
+ CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioCDE_clk),
+ CLKDEV_CON_DEV_ID(NULL, "fffffa00.gpio", &pioCDE_clk),
};
static struct clk_lookup usart_clocks_lookups[] = {
@@ -256,6 +256,12 @@ static struct clk_lookup periph_clocks_lookups[] = {
CLKDEV_CON_DEV_ID("ehci_clk", "800000.ehci", &uhphs_clk),
/* fake hclk clock */
CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &uhphs_clk),
+ CLKDEV_CON_DEV_ID(NULL, "fffff200.gpio", &pioA_clk),
+ CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioB_clk),
+ CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioC_clk),
+ CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioDE_clk),
+ CLKDEV_CON_DEV_ID(NULL, "fffffa00.gpio", &pioDE_clk),
+
CLKDEV_CON_ID("pioA", &pioA_clk),
CLKDEV_CON_ID("pioB", &pioB_clk),
CLKDEV_CON_ID("pioC", &pioC_clk),
@@ -169,10 +169,10 @@ static struct clk_lookup periph_clocks_lookups[] = {
CLKDEV_CON_DEV_ID("t0_clk", "f8008000.timer", &tcb_clk),
CLKDEV_CON_DEV_ID("t0_clk", "f800c000.timer", &tcb_clk),
CLKDEV_CON_DEV_ID("dma_clk", "ffffec00.dma-controller", &dma_clk),
- CLKDEV_CON_ID("pioA", &pioAB_clk),
- CLKDEV_CON_ID("pioB", &pioAB_clk),
- CLKDEV_CON_ID("pioC", &pioCD_clk),
- CLKDEV_CON_ID("pioD", &pioCD_clk),
+ CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioAB_clk),
+ CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioAB_clk),
+ CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioCD_clk),
+ CLKDEV_CON_DEV_ID(NULL, "fffffa00.gpio", &pioCD_clk),
/* additional fake clock for macb_hclk */
CLKDEV_CON_DEV_ID("hclk", "500000.ohci", &uhp_clk),
CLKDEV_CON_DEV_ID("ohci_clk", "500000.ohci", &uhp_clk),
@@ -221,9 +221,6 @@ static void __init at91sam9n12_map_io(void)
void __init at91sam9n12_initialize(void)
{
at91_extern_irq = (1 << AT91SAM9N12_ID_IRQ0);
-
- /* Register GPIO subsystem (using DT) */
- at91_gpio_init(NULL, 0);
}
AT91_SOC_START(sam9n12)
@@ -231,10 +231,10 @@ static struct clk_lookup periph_clocks_lookups[] = {
CLKDEV_CON_DEV_ID("t0_clk", "f800c000.timer", &tcb0_clk),
CLKDEV_CON_DEV_ID("dma_clk", "ffffec00.dma-controller", &dma0_clk),
CLKDEV_CON_DEV_ID("dma_clk", "ffffee00.dma-controller", &dma1_clk),
- CLKDEV_CON_ID("pioA", &pioAB_clk),
- CLKDEV_CON_ID("pioB", &pioAB_clk),
- CLKDEV_CON_ID("pioC", &pioCD_clk),
- CLKDEV_CON_ID("pioD", &pioCD_clk),
+ CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioAB_clk),
+ CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioAB_clk),
+ CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioCD_clk),
+ CLKDEV_CON_DEV_ID(NULL, "fffffa00.gpio", &pioCD_clk),
/* additional fake clock for macb_hclk */
CLKDEV_CON_DEV_ID("hclk", "f802c000.ethernet", &macb0_clk),
CLKDEV_CON_DEV_ID("hclk", "f8030000.ethernet", &macb1_clk),
@@ -310,12 +310,6 @@ static void __init at91sam9x5_map_io(void)
at91_init_sram(0, AT91SAM9X5_SRAM_BASE, AT91SAM9X5_SRAM_SIZE);
}
-void __init at91sam9x5_initialize(void)
-{
- /* Register GPIO subsystem (using DT) */
- at91_gpio_init(NULL, 0);
-}
-
/* --------------------------------------------------------------------
* Interrupt initialization
* -------------------------------------------------------------------- */
@@ -323,5 +317,4 @@ void __init at91sam9x5_initialize(void)
AT91_SOC_START(sam9x5)
.map_io = at91sam9x5_map_io,
.register_clocks = at91sam9x5_register_clocks,
- .init = at91sam9x5_initialize,
AT91_SOC_END
@@ -449,7 +449,8 @@ void __init at91_dt_initialize(void)
/* Register the processor-specific clocks */
at91_boot_soc.register_clocks();
- at91_boot_soc.init();
+ if (at91_boot_soc.init)
+ at91_boot_soc.init();
}
#endif
@@ -749,7 +749,7 @@ static int __devinit at91_pinctrl_parse_groups(struct device_node *np,
grp->name = np->name;
/*
- * the binding format is fsl,pins = <bank pin mux CONFIG ...>,
+ * the binding format is atmel,pins = <bank pin mux CONFIG ...>,
* do sanity check and calculate pins number
*/
list = of_get_property(np, "atmel,pins", &size);