@@ -58,11 +58,16 @@ config TEGRA_AHB
perfomance parameters(priority, prefech size).
choice
- prompt "Default low-level debug console UART"
- default TEGRA_DEBUG_UART_NONE
+ prompt "Low-level debug console UART"
-config TEGRA_DEBUG_UART_NONE
- bool "None"
+config TEGRA_DEBUG_UART_AUTO_ODMDATA
+ bool "Via ODMDATA"
+ help
+ Automatically determines which UART to use for low-level debug based
+ on the ODMDATA value. This value is part of the BCT, and is written
+ to the boot memory device using nvflash, or other flashing tool.
+ When bits 19:18 are 3, then bits 17:15 indicate which UART to use;
+ 0/1/2/3/4 are UART A/B/C/D/E.
config TEGRA_DEBUG_UARTA
bool "UART-A"
@@ -81,33 +86,6 @@ config TEGRA_DEBUG_UARTE
endchoice
-choice
- prompt "Automatic low-level debug console UART"
- default TEGRA_DEBUG_UART_AUTO_NONE
-
-config TEGRA_DEBUG_UART_AUTO_NONE
- bool "None"
-
-config TEGRA_DEBUG_UART_AUTO_ODMDATA
- bool "Via ODMDATA"
- help
- Automatically determines which UART to use for low-level debug based
- on the ODMDATA value. This value is part of the BCT, and is written
- to the boot memory device using nvflash, or other flashing tool.
- When bits 19:18 are 3, then bits 17:15 indicate which UART to use;
- 0/1/2/3/4 are UART A/B/C/D/E.
-
-config TEGRA_DEBUG_UART_AUTO_SCRATCH
- bool "Via UART scratch register"
- help
- Automatically determines which UART to use for low-level debug based
- on the UART scratch register value. Some bootloaders put ASCII 'D'
- in this register when they initialize their own console UART output.
- Using this option allows the kernel to automatically pick the same
- UART.
-
-endchoice
-
config TEGRA_EMC_SCALING_ENABLE
bool "Enable scaling the memory frequency"
@@ -44,14 +44,13 @@
* kernel is loaded. The data is declared here rather than debug-macro.S so
* that multiple inclusions of debug-macro.S point at the same data.
*/
-#define TEGRA_DEBUG_UART_OFFSET (TEGRA_DEBUG_UART_BASE & 0xFFFF)
u32 tegra_uart_config[3] = {
/* Debug UART initialization required */
1,
/* Debug UART physical address */
- (u32)(IO_APB_PHYS + TEGRA_DEBUG_UART_OFFSET),
+ 0,
/* Debug UART virtual address */
- (u32)(IO_APB_VIRT + TEGRA_DEBUG_UART_OFFSET),
+ 0,
};
#ifdef CONFIG_OF
@@ -139,51 +139,19 @@ int auto_odmdata(void)
}
#endif
-#ifdef CONFIG_TEGRA_DEBUG_UART_AUTO_SCRATCH
-int auto_scratch(void)
-{
- int i;
-
- /*
- * Look for the first UART that:
- * a) Is not in reset.
- * b) Is clocked.
- * c) Has a 'D' in the scratchpad register.
- *
- * Note that on Tegra30, the first two conditions are required, since
- * if not true, accesses to the UART scratch register will hang.
- * Tegra20 doesn't have this issue.
- *
- * The intent is that the bootloader will tell the kernel which UART
- * to use by setting up those conditions. If nothing found, we'll fall
- * back to what's specified in TEGRA_DEBUG_UART_BASE.
- */
- for (i = 0; i < ARRAY_SIZE(uarts); i++) {
- if (!uart_clocked(i))
- continue;
-
- uart = (volatile u8 *)uarts[i].base;
- if (uart[UART_SCR << DEBUG_UART_SHIFT] != 'D')
- continue;
-
- return i;
- }
-
- return -1;
-}
-#endif
-
/*
* Setup before decompression. This is where we do UART selection for
* earlyprintk and init the uart_base register.
*/
static inline void arch_decomp_setup(void)
{
- int uart_id, auto_uart_id;
+ int uart_id;
volatile u32 *apb_misc = (volatile u32 *)TEGRA_APB_MISC_BASE;
u32 chip, div;
-#if defined(CONFIG_TEGRA_DEBUG_UARTA)
+#if defined(CONFIG_TEGRA_DEBUG_UART_AUTO_ODMDATA)
+ uart_id = auto_odmdata();
+#elif defined(CONFIG_TEGRA_DEBUG_UARTA)
uart_id = 0;
#elif defined(CONFIG_TEGRA_DEBUG_UARTB)
uart_id = 1;
@@ -193,19 +161,7 @@ static inline void arch_decomp_setup(void)
uart_id = 3;
#elif defined(CONFIG_TEGRA_DEBUG_UARTE)
uart_id = 4;
-#else
- uart_id = -1;
-#endif
-
-#if defined(CONFIG_TEGRA_DEBUG_UART_AUTO_ODMDATA)
- auto_uart_id = auto_odmdata();
-#elif defined(CONFIG_TEGRA_DEBUG_UART_AUTO_SCRATCH)
- auto_uart_id = auto_scratch();
-#else
- auto_uart_id = -1;
#endif
- if (auto_uart_id != -1)
- uart_id = auto_uart_id;
if (uart_id < 0 || uart_id >= ARRAY_SIZE(uarts) ||
!uart_clocked(uart_id))
@@ -261,20 +261,6 @@
#define TEGRA_SDMMC4_BASE 0xC8000600
#define TEGRA_SDMMC4_SIZE SZ_512
-#if defined(CONFIG_TEGRA_DEBUG_UART_NONE)
-# define TEGRA_DEBUG_UART_BASE 0
-#elif defined(CONFIG_TEGRA_DEBUG_UARTA)
-# define TEGRA_DEBUG_UART_BASE TEGRA_UARTA_BASE
-#elif defined(CONFIG_TEGRA_DEBUG_UARTB)
-# define TEGRA_DEBUG_UART_BASE TEGRA_UARTB_BASE
-#elif defined(CONFIG_TEGRA_DEBUG_UARTC)
-# define TEGRA_DEBUG_UART_BASE TEGRA_UARTC_BASE
-#elif defined(CONFIG_TEGRA_DEBUG_UARTD)
-# define TEGRA_DEBUG_UART_BASE TEGRA_UARTD_BASE
-#elif defined(CONFIG_TEGRA_DEBUG_UARTE)
-# define TEGRA_DEBUG_UART_BASE TEGRA_UARTE_BASE
-#endif
-
/* On TEGRA, many peripherals are very closely packed in
* two 256MB io windows (that actually only use about 64KB
* at the start of each).