@@ -37,9 +37,6 @@
#include <plat/usb.h>
#include <plat/mmc.h>
#include "omap4-keypad.h"
-#include <video/omapdss.h>
-#include <video/omap-panel-nokia-dsi.h>
-#include <video/omap-panel-picodlp.h>
#include <linux/wl12xx.h>
#include <linux/platform_data/omap-abe-twl6040.h>
@@ -48,17 +45,13 @@
#include "hsmmc.h"
#include "control.h"
#include "common-board-devices.h"
+#include "dss-common.h"
#define ETH_KS8851_IRQ 34
#define ETH_KS8851_POWER_ON 48
#define ETH_KS8851_QUART 138
#define OMAP4_SFH7741_SENSOR_OUTPUT_GPIO 184
#define OMAP4_SFH7741_ENABLE_GPIO 188
-#define HDMI_GPIO_CT_CP_HPD 60 /* HPD mode enable/disable */
-#define HDMI_GPIO_LS_OE 41 /* Level shifter for HDMI */
-#define HDMI_GPIO_HPD 63 /* Hotplug detect */
-#define DISPLAY_SEL_GPIO 59 /* LCD2/PicoDLP switch */
-#define DLP_POWER_ON_GPIO 40
#define GPIO_WIFI_PMENA 54
#define GPIO_WIFI_IRQ 53
@@ -607,154 +600,6 @@ static void __init omap_sfh7741prox_init(void)
__func__, OMAP4_SFH7741_ENABLE_GPIO, error);
}
-static struct nokia_dsi_panel_data dsi1_panel = {
- .name = "taal",
- .reset_gpio = 102,
- .use_ext_te = false,
- .ext_te_gpio = 101,
- .esd_interval = 0,
- .pin_config = {
- .num_pins = 6,
- .pins = { 0, 1, 2, 3, 4, 5 },
- },
-};
-
-static struct omap_dss_device sdp4430_lcd_device = {
- .name = "lcd",
- .driver_name = "taal",
- .type = OMAP_DISPLAY_TYPE_DSI,
- .data = &dsi1_panel,
- .phy.dsi = {
- .module = 0,
- },
- .channel = OMAP_DSS_CHANNEL_LCD,
-};
-
-static struct nokia_dsi_panel_data dsi2_panel = {
- .name = "taal",
- .reset_gpio = 104,
- .use_ext_te = false,
- .ext_te_gpio = 103,
- .esd_interval = 0,
- .pin_config = {
- .num_pins = 6,
- .pins = { 0, 1, 2, 3, 4, 5 },
- },
-};
-
-static struct omap_dss_device sdp4430_lcd2_device = {
- .name = "lcd2",
- .driver_name = "taal",
- .type = OMAP_DISPLAY_TYPE_DSI,
- .data = &dsi2_panel,
- .phy.dsi = {
-
- .module = 1,
- },
- .channel = OMAP_DSS_CHANNEL_LCD2,
-};
-
-static struct omap_dss_hdmi_data sdp4430_hdmi_data = {
- .ct_cp_hpd_gpio = HDMI_GPIO_CT_CP_HPD,
- .ls_oe_gpio = HDMI_GPIO_LS_OE,
- .hpd_gpio = HDMI_GPIO_HPD,
-};
-
-static struct omap_dss_device sdp4430_hdmi_device = {
- .name = "hdmi",
- .driver_name = "hdmi_panel",
- .type = OMAP_DISPLAY_TYPE_HDMI,
- .channel = OMAP_DSS_CHANNEL_DIGIT,
- .data = &sdp4430_hdmi_data,
-};
-
-static struct picodlp_panel_data sdp4430_picodlp_pdata = {
- .picodlp_adapter_id = 2,
- .emu_done_gpio = 44,
- .pwrgood_gpio = 45,
-};
-
-static void sdp4430_picodlp_init(void)
-{
- int r;
- const struct gpio picodlp_gpios[] = {
- {DLP_POWER_ON_GPIO, GPIOF_OUT_INIT_LOW,
- "DLP POWER ON"},
- {sdp4430_picodlp_pdata.emu_done_gpio, GPIOF_IN,
- "DLP EMU DONE"},
- {sdp4430_picodlp_pdata.pwrgood_gpio, GPIOF_OUT_INIT_LOW,
- "DLP PWRGOOD"},
- };
-
- r = gpio_request_array(picodlp_gpios, ARRAY_SIZE(picodlp_gpios));
- if (r)
- pr_err("Cannot request PicoDLP GPIOs, error %d\n", r);
-}
-
-static int sdp4430_panel_enable_picodlp(struct omap_dss_device *dssdev)
-{
- gpio_set_value(DISPLAY_SEL_GPIO, 0);
- gpio_set_value(DLP_POWER_ON_GPIO, 1);
-
- return 0;
-}
-
-static void sdp4430_panel_disable_picodlp(struct omap_dss_device *dssdev)
-{
- gpio_set_value(DLP_POWER_ON_GPIO, 0);
- gpio_set_value(DISPLAY_SEL_GPIO, 1);
-}
-
-static struct omap_dss_device sdp4430_picodlp_device = {
- .name = "picodlp",
- .driver_name = "picodlp_panel",
- .type = OMAP_DISPLAY_TYPE_DPI,
- .phy.dpi.data_lines = 24,
- .channel = OMAP_DSS_CHANNEL_LCD2,
- .platform_enable = sdp4430_panel_enable_picodlp,
- .platform_disable = sdp4430_panel_disable_picodlp,
- .data = &sdp4430_picodlp_pdata,
-};
-
-static struct omap_dss_device *sdp4430_dss_devices[] = {
- &sdp4430_lcd_device,
- &sdp4430_lcd2_device,
- &sdp4430_hdmi_device,
- &sdp4430_picodlp_device,
-};
-
-static struct omap_dss_board_info sdp4430_dss_data = {
- .num_devices = ARRAY_SIZE(sdp4430_dss_devices),
- .devices = sdp4430_dss_devices,
- .default_device = &sdp4430_lcd_device,
-};
-
-static void __init omap_4430sdp_display_init(void)
-{
- int r;
-
- /* Enable LCD2 by default (instead of Pico DLP) */
- r = gpio_request_one(DISPLAY_SEL_GPIO, GPIOF_OUT_INIT_HIGH,
- "display_sel");
- if (r)
- pr_err("%s: Could not get display_sel GPIO\n", __func__);
-
- sdp4430_picodlp_init();
- omap_display_init(&sdp4430_dss_data);
- /*
- * OMAP4460SDP/Blaze and OMAP4430 ES2.3 SDP/Blaze boards and
- * later have external pull up on the HDMI I2C lines
- */
- if (cpu_is_omap446x() || omap_rev() > OMAP4430_REV_ES2_2)
- omap_hdmi_init(OMAP_HDMI_SDA_SCL_EXTERNAL_PULLUP);
- else
- omap_hdmi_init(0);
-
- omap_mux_init_gpio(HDMI_GPIO_LS_OE, OMAP_PIN_OUTPUT);
- omap_mux_init_gpio(HDMI_GPIO_CT_CP_HPD, OMAP_PIN_OUTPUT);
- omap_mux_init_gpio(HDMI_GPIO_HPD, OMAP_PIN_INPUT_PULLDOWN);
-}
-
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
OMAP4_MUX(USBB2_ULPITLL_CLK, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
@@ -24,8 +24,12 @@
*/
#include <linux/kernel.h>
+#include <linux/gpio.h>
+
#include <video/omapdss.h>
#include <video/omap-panel-tfp410.h>
+#include <video/omap-panel-nokia-dsi.h>
+#include <video/omap-panel-picodlp.h>
#include <plat/cpu.h>
@@ -102,3 +106,171 @@ void __init omap4_panda_display_init_of(void)
{
omap_display_init(&omap4_panda_dss_data);
}
+
+
+/* OMAP4 Blaze display data */
+
+#define DISPLAY_SEL_GPIO 59 /* LCD2/PicoDLP switch */
+#define DLP_POWER_ON_GPIO 40
+
+static struct nokia_dsi_panel_data dsi1_panel = {
+ .name = "taal",
+ .reset_gpio = 102,
+ .use_ext_te = false,
+ .ext_te_gpio = 101,
+ .esd_interval = 0,
+ .pin_config = {
+ .num_pins = 6,
+ .pins = { 0, 1, 2, 3, 4, 5 },
+ },
+};
+
+static struct omap_dss_device sdp4430_lcd_device = {
+ .name = "lcd",
+ .driver_name = "taal",
+ .type = OMAP_DISPLAY_TYPE_DSI,
+ .data = &dsi1_panel,
+ .phy.dsi = {
+ .module = 0,
+ },
+ .channel = OMAP_DSS_CHANNEL_LCD,
+};
+
+static struct nokia_dsi_panel_data dsi2_panel = {
+ .name = "taal",
+ .reset_gpio = 104,
+ .use_ext_te = false,
+ .ext_te_gpio = 103,
+ .esd_interval = 0,
+ .pin_config = {
+ .num_pins = 6,
+ .pins = { 0, 1, 2, 3, 4, 5 },
+ },
+};
+
+static struct omap_dss_device sdp4430_lcd2_device = {
+ .name = "lcd2",
+ .driver_name = "taal",
+ .type = OMAP_DISPLAY_TYPE_DSI,
+ .data = &dsi2_panel,
+ .phy.dsi = {
+
+ .module = 1,
+ },
+ .channel = OMAP_DSS_CHANNEL_LCD2,
+};
+
+static struct omap_dss_hdmi_data sdp4430_hdmi_data = {
+ .ct_cp_hpd_gpio = HDMI_GPIO_CT_CP_HPD,
+ .ls_oe_gpio = HDMI_GPIO_LS_OE,
+ .hpd_gpio = HDMI_GPIO_HPD,
+};
+
+static struct omap_dss_device sdp4430_hdmi_device = {
+ .name = "hdmi",
+ .driver_name = "hdmi_panel",
+ .type = OMAP_DISPLAY_TYPE_HDMI,
+ .channel = OMAP_DSS_CHANNEL_DIGIT,
+ .data = &sdp4430_hdmi_data,
+};
+
+static struct picodlp_panel_data sdp4430_picodlp_pdata = {
+ .picodlp_adapter_id = 2,
+ .emu_done_gpio = 44,
+ .pwrgood_gpio = 45,
+};
+
+static void sdp4430_picodlp_init(void)
+{
+ int r;
+ const struct gpio picodlp_gpios[] = {
+ {DLP_POWER_ON_GPIO, GPIOF_OUT_INIT_LOW,
+ "DLP POWER ON"},
+ {sdp4430_picodlp_pdata.emu_done_gpio, GPIOF_IN,
+ "DLP EMU DONE"},
+ {sdp4430_picodlp_pdata.pwrgood_gpio, GPIOF_OUT_INIT_LOW,
+ "DLP PWRGOOD"},
+ };
+
+ r = gpio_request_array(picodlp_gpios, ARRAY_SIZE(picodlp_gpios));
+ if (r)
+ pr_err("Cannot request PicoDLP GPIOs, error %d\n", r);
+}
+
+static int sdp4430_panel_enable_picodlp(struct omap_dss_device *dssdev)
+{
+ gpio_set_value(DISPLAY_SEL_GPIO, 0);
+ gpio_set_value(DLP_POWER_ON_GPIO, 1);
+
+ return 0;
+}
+
+static void sdp4430_panel_disable_picodlp(struct omap_dss_device *dssdev)
+{
+ gpio_set_value(DLP_POWER_ON_GPIO, 0);
+ gpio_set_value(DISPLAY_SEL_GPIO, 1);
+}
+
+static struct omap_dss_device sdp4430_picodlp_device = {
+ .name = "picodlp",
+ .driver_name = "picodlp_panel",
+ .type = OMAP_DISPLAY_TYPE_DPI,
+ .phy.dpi.data_lines = 24,
+ .channel = OMAP_DSS_CHANNEL_LCD2,
+ .platform_enable = sdp4430_panel_enable_picodlp,
+ .platform_disable = sdp4430_panel_disable_picodlp,
+ .data = &sdp4430_picodlp_pdata,
+};
+
+static struct omap_dss_device *sdp4430_dss_devices[] = {
+ &sdp4430_lcd_device,
+ &sdp4430_lcd2_device,
+ &sdp4430_hdmi_device,
+ &sdp4430_picodlp_device,
+};
+
+static struct omap_dss_board_info sdp4430_dss_data = {
+ .num_devices = ARRAY_SIZE(sdp4430_dss_devices),
+ .devices = sdp4430_dss_devices,
+ .default_device = &sdp4430_lcd_device,
+};
+
+void __init omap_4430sdp_display_init(void)
+{
+ int r;
+
+ /* Enable LCD2 by default (instead of Pico DLP) */
+ r = gpio_request_one(DISPLAY_SEL_GPIO, GPIOF_OUT_INIT_HIGH,
+ "display_sel");
+ if (r)
+ pr_err("%s: Could not get display_sel GPIO\n", __func__);
+
+ sdp4430_picodlp_init();
+ omap_display_init(&sdp4430_dss_data);
+ /*
+ * OMAP4460SDP/Blaze and OMAP4430 ES2.3 SDP/Blaze boards and
+ * later have external pull up on the HDMI I2C lines
+ */
+ if (cpu_is_omap446x() || omap_rev() > OMAP4430_REV_ES2_2)
+ omap_hdmi_init(OMAP_HDMI_SDA_SCL_EXTERNAL_PULLUP);
+ else
+ omap_hdmi_init(0);
+
+ omap_mux_init_gpio(HDMI_GPIO_LS_OE, OMAP_PIN_OUTPUT);
+ omap_mux_init_gpio(HDMI_GPIO_CT_CP_HPD, OMAP_PIN_OUTPUT);
+ omap_mux_init_gpio(HDMI_GPIO_HPD, OMAP_PIN_INPUT_PULLDOWN);
+}
+
+void __init omap_4430sdp_display_init_of(void)
+{
+ int r;
+
+ /* Enable LCD2 by default (instead of Pico DLP) */
+ r = gpio_request_one(DISPLAY_SEL_GPIO, GPIOF_OUT_INIT_HIGH,
+ "display_sel");
+ if (r)
+ pr_err("%s: Could not get display_sel GPIO\n", __func__);
+
+ sdp4430_picodlp_init();
+ omap_display_init(&sdp4430_dss_data);
+}
@@ -8,5 +8,7 @@
void __init omap4_panda_display_init(void);
void __init omap4_panda_display_init_of(void);
+void __init omap_4430sdp_display_init(void);
+void __init omap_4430sdp_display_init_of(void);
#endif
Device tree support for omapdss is still some way in the future. In an effort to get a minimal DSS support for DT enabled kernel on selected OMAP4 boards, we'll go for a temporary solution: We will call the same non-DT omapdss setup code for OMAP4 SDP and Pandaboards from board-generic.c, thus enabling DSS for those boards. This patch moves the display setup code from board-4430sdp.c to dss-common.c. dss-common.c will be called by the board-4430sdp.c when running on non-DT kernel, and by board-generic.c when running on DT enabled kernel. Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> --- arch/arm/mach-omap2/board-4430sdp.c | 157 +------------------------------- arch/arm/mach-omap2/dss-common.c | 172 +++++++++++++++++++++++++++++++++++ arch/arm/mach-omap2/dss-common.h | 2 + 3 files changed, 175 insertions(+), 156 deletions(-)