@@ -3,6 +3,9 @@ OMAP GLUE AND OTHER OMAP SPECIFIC COMPONENTS
OMAP MUSB GLUE
- compatible : Should be "ti,omap4-musb" or "ti,omap3-musb"
- ti,hwmods : must be "usb_otg_hs"
+ - ti,has_mailbox : to specify that omap uses an external mailbox
+ (in control module) to communicate with the musb core during device connect
+ and disconnect.
- multipoint : Should be "1" indicating the musb controller supports
multipoint. This is a MUSB configuration-specific setting.
- num_eps : Specifies the number of endpoints. This is also a
@@ -24,6 +27,7 @@ SOC specific device node entry
usb_otg_hs: usb_otg_hs@4a0ab000 {
compatible = "ti,omap4-musb";
ti,hwmods = "usb_otg_hs";
+ ti,has_mailbox;
multipoint = <1>;
num_eps = <16>;
ram_bits = <12>;
@@ -4,9 +4,7 @@ OMAP USB2 PHY
Required properties:
- compatible: Should be "ti,omap-usb2"
- - reg : Address and length of the register set for the device. Also
-add the address of control module dev conf register until a driver for
-control module is added
+ - reg : Address and length of the register set for the device.
Optional properties:
- ctrl_module : phandle of the control module used by PHY driver to power on
@@ -16,7 +14,6 @@ This is usually a subnode of ocp2scp to which it is connected.
usb2phy@4a0ad080 {
compatible = "ti,omap-usb2";
- reg = <0x4a0ad080 0x58>,
- <0x4a002300 0x4>;
+ reg = <0x4a0ad080 0x58>;
ctrl_module = <&omap_control_usb>;
};
@@ -2698,13 +2698,6 @@ static struct resource omap44xx_usb_phy_and_pll_addrs[] = {
.end = 0x4a0ae000,
.flags = IORESOURCE_MEM,
},
- {
- /* XXX: Remove this once control module driver is in place */
- .name = "ctrl_dev",
- .start = 0x4a002300,
- .end = 0x4a002303,
- .flags = IORESOURCE_MEM,
- },
{ }
};
@@ -6152,12 +6145,6 @@ static struct omap_hwmod_addr_space omap44xx_usb_otg_hs_addrs[] = {
.pa_end = 0x4a0ab7ff,
.flags = ADDR_TYPE_RT
},
- {
- /* XXX: Remove this once control module driver is in place */
- .pa_start = 0x4a00233c,
- .pa_end = 0x4a00233f,
- .flags = ADDR_TYPE_RT
- },
{ }
};
@@ -11,6 +11,7 @@ config USB_MUSB_HDRC
select NOP_USB_XCEIV if (SOC_TI81XX || SOC_AM33XX)
select TWL4030_USB if MACH_OMAP_3430SDP
select TWL6030_USB if MACH_OMAP_4430SDP || MACH_OMAP4_PANDA
+ select OMAP_CONTROL_USB if MACH_OMAP_4430SDP || MACH_OMAP4_PANDA
select USB_OTG_UTILS
help
Say Y here if your system has a dual role high speed USB
@@ -37,6 +37,7 @@
#include <linux/err.h>
#include <linux/delay.h>
#include <linux/usb/musb-omap.h>
+#include <linux/usb/omap_control_usb.h>
#include "musb_core.h"
#include "omap2430.h"
@@ -46,7 +47,7 @@ struct omap2430_glue {
struct platform_device *musb;
enum omap_musb_vbus_id_status status;
struct work_struct omap_musb_mailbox_work;
- u32 __iomem *control_otghs;
+ struct device *control_otghs;
};
#define glue_to_musb(g) platform_get_drvdata(g->musb)
@@ -54,26 +55,6 @@ struct omap2430_glue *_glue;
static struct timer_list musb_idle_timer;
-/**
- * omap4_usb_phy_mailbox - write to usb otg mailbox
- * @glue: struct omap2430_glue *
- * @val: the value to be written to the mailbox
- *
- * On detection of a device (ID pin is grounded), this API should be called
- * to set AVALID, VBUSVALID and ID pin is grounded.
- *
- * When OMAP is connected to a host (OMAP in device mode), this API
- * is called to set AVALID, VBUSVALID and ID pin in high impedance.
- *
- * XXX: This function will be removed once we have a seperate driver for
- * control module
- */
-static void omap4_usb_phy_mailbox(struct omap2430_glue *glue, u32 val)
-{
- if (glue->control_otghs)
- writel(val, glue->control_otghs);
-}
-
static void musb_do_idle(unsigned long _musb)
{
struct musb *musb = (void *)_musb;
@@ -269,7 +250,6 @@ EXPORT_SYMBOL_GPL(omap_musb_mailbox);
static void omap_musb_set_mailbox(struct omap2430_glue *glue)
{
- u32 val;
struct musb *musb = glue_to_musb(glue);
struct device *dev = musb->controller;
struct musb_hdrc_platform_data *pdata = dev->platform_data;
@@ -285,8 +265,8 @@ static void omap_musb_set_mailbox(struct omap2430_glue *glue)
musb->xceiv->last_event = USB_EVENT_ID;
if (musb->gadget_driver) {
pm_runtime_get_sync(dev);
- val = AVALID | VBUSVALID;
- omap4_usb_phy_mailbox(glue, val);
+ omap_control_usb_set_mode(glue->control_otghs,
+ USB_MODE_HOST);
omap2430_musb_set_vbus(musb, 1);
}
break;
@@ -299,8 +279,7 @@ static void omap_musb_set_mailbox(struct omap2430_glue *glue)
musb->xceiv->last_event = USB_EVENT_VBUS;
if (musb->gadget_driver)
pm_runtime_get_sync(dev);
- val = IDDIG | AVALID | VBUSVALID;
- omap4_usb_phy_mailbox(glue, val);
+ omap_control_usb_set_mode(glue->control_otghs, USB_MODE_DEVICE);
break;
case OMAP_MUSB_ID_FLOAT:
@@ -317,8 +296,8 @@ static void omap_musb_set_mailbox(struct omap2430_glue *glue)
if (musb->xceiv->otg->set_vbus)
otg_set_vbus(musb->xceiv->otg, 0);
}
- val = SESSEND | IDDIG;
- omap4_usb_phy_mailbox(glue, val);
+ omap_control_usb_set_mode(glue->control_otghs,
+ USB_MODE_DISCONNECT);
break;
default:
dev_dbg(dev, "ID float\n");
@@ -415,7 +394,6 @@ err1:
static void omap2430_musb_enable(struct musb *musb)
{
u8 devctl;
- u32 val;
unsigned long timeout = jiffies + msecs_to_jiffies(1000);
struct device *dev = musb->controller;
struct omap2430_glue *glue = dev_get_drvdata(dev->parent);
@@ -425,8 +403,7 @@ static void omap2430_musb_enable(struct musb *musb)
switch (glue->status) {
case OMAP_MUSB_ID_GROUND:
- val = AVALID | VBUSVALID;
- omap4_usb_phy_mailbox(glue, val);
+ omap_control_usb_set_mode(glue->control_otghs, USB_MODE_HOST);
if (data->interface_type != MUSB_INTERFACE_UTMI)
break;
devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
@@ -445,8 +422,7 @@ static void omap2430_musb_enable(struct musb *musb)
break;
case OMAP_MUSB_VBUS_VALID:
- val = IDDIG | AVALID | VBUSVALID;
- omap4_usb_phy_mailbox(glue, val);
+ omap_control_usb_set_mode(glue->control_otghs, USB_MODE_DEVICE);
break;
default:
@@ -456,14 +432,12 @@ static void omap2430_musb_enable(struct musb *musb)
static void omap2430_musb_disable(struct musb *musb)
{
- u32 val;
struct device *dev = musb->controller;
struct omap2430_glue *glue = dev_get_drvdata(dev->parent);
- if (glue->status != OMAP_MUSB_UNKNOWN) {
- val = SESSEND | IDDIG;
- omap4_usb_phy_mailbox(glue, val);
- }
+ if (glue->status != OMAP_MUSB_UNKNOWN)
+ omap_control_usb_set_mode(glue->control_otghs,
+ USB_MODE_DISCONNECT);
}
static int omap2430_musb_exit(struct musb *musb)
@@ -498,7 +472,6 @@ static int omap2430_probe(struct platform_device *pdev)
struct omap2430_glue *glue;
struct device_node *np = pdev->dev.of_node;
struct musb_hdrc_config *config;
- struct resource *res;
int ret = -ENOMEM;
glue = devm_kzalloc(&pdev->dev, sizeof(*glue), GFP_KERNEL);
@@ -521,12 +494,6 @@ static int omap2430_probe(struct platform_device *pdev)
glue->musb = musb;
glue->status = OMAP_MUSB_UNKNOWN;
- res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
-
- glue->control_otghs = devm_request_and_ioremap(&pdev->dev, res);
- if (glue->control_otghs == NULL)
- dev_dbg(&pdev->dev, "Failed to obtain control memory\n");
-
if (np) {
pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
if (!pdata) {
@@ -558,11 +525,22 @@ static int omap2430_probe(struct platform_device *pdev)
of_property_read_u32(np, "ram_bits", (u32 *)&config->ram_bits);
of_property_read_u32(np, "power", (u32 *)&pdata->power);
config->multipoint = of_property_read_bool(np, "multipoint");
+ pdata->has_mailbox = of_property_read_bool(np,
+ "ti,has_mailbox");
pdata->board_data = data;
pdata->config = config;
}
+ if (pdata->has_mailbox) {
+ glue->control_otghs = omap_get_control_dev();
+ if (IS_ERR(glue->control_otghs)) {
+ dev_vdbg(&pdev->dev, "Failed to get control device\n");
+ return -ENODEV;
+ }
+ } else {
+ glue->control_otghs = ERR_PTR(-ENODEV);
+ }
pdata->platform_ops = &omap2430_ops;
platform_set_drvdata(pdev, glue);
@@ -49,13 +49,4 @@
#define OTG_FORCESTDBY 0x414
# define ENABLEFORCE (1 << 0)
-/*
- * Control Module bit definitions
- * XXX: Will be removed once we have a driver for control module.
- */
-#define AVALID BIT(0)
-#define BVALID BIT(1)
-#define VBUSVALID BIT(2)
-#define SESSEND BIT(3)
-#define IDDIG BIT(4)
#endif /* __MUSB_OMAP243X_H__ */
@@ -8,6 +8,7 @@ config OMAP_USB2
tristate "OMAP USB2 PHY Driver"
depends on ARCH_OMAP2PLUS
select USB_OTG_UTILS
+ select OMAP_CONTROL_USB
help
Enable this to support the transceiver that is part of SOC. This
driver takes care of all the PHY functionality apart from comparator.
@@ -27,6 +27,7 @@
#include <linux/err.h>
#include <linux/pm_runtime.h>
#include <linux/delay.h>
+#include <linux/usb/omap_control_usb.h>
/**
* omap_usb2_set_comparator - links the comparator present in the sytem with
@@ -52,29 +53,6 @@ int omap_usb2_set_comparator(struct phy_companion *comparator)
}
EXPORT_SYMBOL_GPL(omap_usb2_set_comparator);
-/**
- * omap_usb_phy_power - power on/off the phy using control module reg
- * @phy: struct omap_usb *
- * @on: 0 or 1, based on powering on or off the PHY
- *
- * XXX: Remove this function once control module driver gets merged
- */
-static void omap_usb_phy_power(struct omap_usb *phy, int on)
-{
- u32 val;
-
- if (on) {
- val = readl(phy->control_dev);
- if (val & PHY_PD) {
- writel(~PHY_PD, phy->control_dev);
- /* XXX: add proper documentation for this delay */
- mdelay(200);
- }
- } else {
- writel(PHY_PD, phy->control_dev);
- }
-}
-
static int omap_usb_set_vbus(struct usb_otg *otg, bool enabled)
{
struct omap_usb *phy = phy_to_omapusb(otg->phy);
@@ -124,7 +102,7 @@ static int omap_usb2_suspend(struct usb_phy *x, int suspend)
struct omap_usb *phy = phy_to_omapusb(x);
if (suspend && !phy->is_suspended) {
- omap_usb_phy_power(phy, 0);
+ omap_control_usb_phy_power(phy->control_dev, 0);
pm_runtime_put_sync(phy->dev);
phy->is_suspended = 1;
} else if (!suspend && phy->is_suspended) {
@@ -134,7 +112,7 @@ static int omap_usb2_suspend(struct usb_phy *x, int suspend)
ret);
return ret;
}
- omap_usb_phy_power(phy, 1);
+ omap_control_usb_phy_power(phy->control_dev, 1);
phy->is_suspended = 0;
}
@@ -145,7 +123,6 @@ static int omap_usb2_probe(struct platform_device *pdev)
{
struct omap_usb *phy;
struct usb_otg *otg;
- struct resource *res;
phy = devm_kzalloc(&pdev->dev, sizeof(*phy), GFP_KERNEL);
if (!phy) {
@@ -166,16 +143,14 @@ static int omap_usb2_probe(struct platform_device *pdev)
phy->phy.set_suspend = omap_usb2_suspend;
phy->phy.otg = otg;
- res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
-
- phy->control_dev = devm_request_and_ioremap(&pdev->dev, res);
- if (phy->control_dev == NULL) {
- dev_err(&pdev->dev, "Failed to obtain io memory\n");
- return -ENXIO;
+ phy->control_dev = omap_get_control_dev();
+ if (IS_ERR(phy->control_dev)) {
+ dev_dbg(&pdev->dev, "Failed to get control device\n");
+ return -ENODEV;
}
phy->is_suspended = 1;
- omap_usb_phy_power(phy, 0);
+ omap_control_usb_phy_power(phy->control_dev, 0);
otg->set_host = omap_usb_set_host;
otg->set_peripheral = omap_usb_set_peripheral;
@@ -25,13 +25,11 @@ struct omap_usb {
struct usb_phy phy;
struct phy_companion *comparator;
struct device *dev;
- u32 __iomem *control_dev;
+ struct device *control_dev;
struct clk *wkupclk;
u8 is_suspended:1;
};
-#define PHY_PD 0x1
-
#define phy_to_omapusb(x) container_of((x), struct omap_usb, phy)
#if defined(CONFIG_OMAP_USB2) || defined(CONFIG_OMAP_USB2_MODULE)
Start using the control module driver for powering on the PHY and for writing to the mailbox instead of writing to the control module registers on their own. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> --- Documentation/devicetree/bindings/usb/omap-usb.txt | 4 ++ Documentation/devicetree/bindings/usb/usb-phy.txt | 7 +- arch/arm/mach-omap2/omap_hwmod_44xx_data.c | 13 ---- drivers/usb/musb/Kconfig | 1 + drivers/usb/musb/omap2430.c | 68 +++++++------------- drivers/usb/musb/omap2430.h | 9 --- drivers/usb/phy/Kconfig | 1 + drivers/usb/phy/omap-usb2.c | 41 +++--------- include/linux/usb/omap_usb.h | 4 +- 9 files changed, 40 insertions(+), 108 deletions(-)