@@ -38,6 +38,7 @@ CONFIG_MACH_TOPKICK_DT=y
CONFIG_MACH_TS219=y
CONFIG_MACH_TS41X=y
CONFIG_MACH_DOCKSTAR=y
+CONFIG_MACH_POGO_E02=y
CONFIG_MACH_OPENRD_BASE=y
CONFIG_MACH_OPENRD_CLIENT=y
CONFIG_MACH_OPENRD_ULTIMATE=y
@@ -214,6 +214,14 @@ config MACH_DOCKSTAR
Say 'Y' here if you want your kernel to support the
Seagate FreeAgent DockStar.
+config MACH_POGO_E02
+ bool "CE Pogoplug E02"
+ help
+ Say 'Y' here if you want your kernel to support the
+ CloudEngines Pogoplug e02 (pink/gray). It differs from Marvell's
+ SheevaPlug Reference Board by a few details, but
+ especially in the led assignments.
+
config MACH_OPENRD
bool
@@ -8,6 +8,7 @@ obj-$(CONFIG_MACH_SHEEVAPLUG) += sheevaplug-setup.o
obj-$(CONFIG_MACH_ESATA_SHEEVAPLUG) += sheevaplug-setup.o
obj-$(CONFIG_MACH_GURUPLUG) += guruplug-setup.o
obj-$(CONFIG_MACH_DOCKSTAR) += dockstar-setup.o
+obj-$(CONFIG_MACH_POGO_E02) += pogo_e02-setup.o
obj-$(CONFIG_MACH_TS219) += ts219-setup.o tsx1x-common.o
obj-$(CONFIG_MACH_TS41X) += ts41x-setup.o tsx1x-common.o
obj-$(CONFIG_MACH_OPENRD) += openrd-setup.o
new file mode 100644
@@ -0,0 +1,122 @@
+/*
+ * arch/arm/mach-kirkwood/pogo_e02-setup.c
+ *
+ * CloudEngines Pogoplug E02 support
+ *
+ * Copyright (C) 2013 Christoph Junghans <ottxor@gentoo.org>
+ * Based on a patch in Arch Linux for Arm by:
+ * Copyright (C) 2012 Kevin Mihelich <kevin@plugapps.com>
+ * and <pazos@lavabit.com>
+ *
+ * Based on the board file sheevaplug-setup.c
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/ata_platform.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mv643xx_eth.h>
+#include <linux/gpio.h>
+#include <linux/leds.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <mach/kirkwood.h>
+#include "common.h"
+#include "mpp.h"
+
+static struct mtd_partition pogo_e02_nand_parts[] = {
+ {
+ .name = "u-boot",
+ .offset = 0,
+ .size = SZ_1M
+ }, {
+ .name = "uImage",
+ .offset = MTDPART_OFS_NXTBLK,
+ .size = SZ_4M
+ }, {
+ .name = "pogoplug",
+ .offset = MTDPART_OFS_NXTBLK,
+ .size = SZ_32M
+ }, {
+ .name = "root",
+ .offset = MTDPART_OFS_NXTBLK,
+ .size = MTDPART_SIZ_FULL
+ },
+};
+
+static struct mv643xx_eth_platform_data pogo_e02_ge00_data = {
+ .phy_addr = MV643XX_ETH_PHY_ADDR(0),
+};
+
+static struct gpio_led pogo_e02_led_pins[] = {
+ {
+ .name = "status:green:health",
+ .default_trigger = "default-on",
+ .gpio = 48,
+ .active_low = 1,
+ },
+ {
+ .name = "status:orange:fault",
+ .default_trigger = "none",
+ .gpio = 49,
+ .active_low = 1,
+ }
+};
+
+static struct gpio_led_platform_data pogo_e02_led_data = {
+ .leds = pogo_e02_led_pins,
+ .num_leds = ARRAY_SIZE(pogo_e02_led_pins),
+};
+
+static struct platform_device pogo_e02_leds = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
+ .platform_data = &pogo_e02_led_data,
+ }
+};
+
+static unsigned int pogo_e02_mpp_config[] __initdata = {
+ MPP29_GPIO, /* USB Power Enable */
+ MPP48_GPIO, /* LED Green */
+ MPP49_GPIO, /* LED Orange */
+ 0
+};
+
+static void __init pogo_e02_init(void)
+{
+ /*
+ * Basic setup. Needs to be called early.
+ */
+ kirkwood_init();
+
+ /* setup gpio pin select */
+ kirkwood_mpp_conf(pogo_e02_mpp_config);
+
+ kirkwood_uart0_init();
+ kirkwood_nand_init(ARRAY_AND_SIZE(pogo_e02_nand_parts), 25);
+
+ if (gpio_request(29, "USB Power Enable") != 0 ||
+ gpio_direction_output(29, 1) != 0)
+ pr_err("can't set up GPIO 29 (USB Power Enable)\n");
+ kirkwood_ehci_init();
+
+ kirkwood_ge00_init(&pogo_e02_ge00_data);
+
+ platform_device_register(&pogo_e02_leds);
+}
+
+MACHINE_START(POGO_E02, "Pogoplug E02")
+ .atag_offset = 0x100,
+ .init_machine = pogo_e02_init,
+ .map_io = kirkwood_map_io,
+ .init_early = kirkwood_init_early,
+ .init_irq = kirkwood_init_irq,
+ .timer = &kirkwood_timer,
+ .restart = kirkwood_restart,
+MACHINE_END
The pogoplug differs from the SheevaPlug only by a few details, but especially in the led assignments. This patch was tested under Gentoo Linux. A version of this patch was included in Arch Linux on Arm since Jan 2012: https://github.com/archlinuxarm/PKGBUILDs/pull/124 A similar patch is available for OpenWrt: http://patchwork.openwrt.org/patch/1412/ Signed-off-by: Christoph Junghans <ottxor@gentoo.org> --- arch/arm/configs/kirkwood_defconfig | 1 + arch/arm/mach-kirkwood/Kconfig | 8 +++ arch/arm/mach-kirkwood/Makefile | 1 + arch/arm/mach-kirkwood/pogo_e02-setup.c | 122 ++++++++++++++++++++++++++++++++ 4 files changed, 132 insertions(+) create mode 100644 arch/arm/mach-kirkwood/pogo_e02-setup.c