| Message ID | 1360602659-4774-10-git-send-email-haojian.zhuang@linaro.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
* Haojian Zhuang <haojian.zhuang@linaro.org> [130211 09:15]: > There's only one bit to control pin bias as enabled or disabled for some > pins in OMAP SoC. So append PIN_CONFIG_BIAS_AUTO_PULL for this case. > User shouldn't switch pin state between AUTO_PULL and PULL_UP/PULL_DOWN, > since they're similiar concepts. Please just drop patch from the series for now. This needs further research on what the hardware is actually doing. I suspect we can replace this with just either PIN_CONFIG_BIAS_PULL_UP or PIN_CONFIG_BIAS_PULL_DOWN. Regards, Tony > Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org> > --- > drivers/pinctrl/pinconf-generic.c | 1 + > include/linux/pinctrl/pinconf-generic.h | 3 +++ > 2 files changed, 4 insertions(+) > > diff --git a/drivers/pinctrl/pinconf-generic.c b/drivers/pinctrl/pinconf-generic.c > index ef24230..4a67848 100644 > --- a/drivers/pinctrl/pinconf-generic.c > +++ b/drivers/pinctrl/pinconf-generic.c > @@ -37,6 +37,7 @@ struct pin_config_item { > struct pin_config_item conf_items[] = { > PCONFDUMP(PIN_CONFIG_BIAS_DISABLE, "input bias disabled", NULL), > PCONFDUMP(PIN_CONFIG_BIAS_HIGH_IMPEDANCE, "input bias high impedance", NULL), > + PCONFDUMP(PIN_CONFIG_BIAS_AUTO_PULL, "input bias auto pull", NULL), > PCONFDUMP(PIN_CONFIG_BIAS_PULL_UP, "input bias pull up", NULL), > PCONFDUMP(PIN_CONFIG_BIAS_PULL_DOWN, "input bias pull down", NULL), > PCONFDUMP(PIN_CONFIG_DRIVE_PUSH_PULL, "output drive push pull", NULL), > diff --git a/include/linux/pinctrl/pinconf-generic.h b/include/linux/pinctrl/pinconf-generic.h > index 3e7909a..f2daff4 100644 > --- a/include/linux/pinctrl/pinconf-generic.h > +++ b/include/linux/pinctrl/pinconf-generic.h > @@ -29,6 +29,8 @@ > * if for example some other pin is going to drive the signal connected > * to it for a while. Pins used for input are usually always high > * impedance. > + * @PIN_CONFIG_BIAS_AUTO_PULL: the pin will be pulled without specifying > + * pull-up or pull-down. > * @PIN_CONFIG_BIAS_PULL_UP: the pin will be pulled up (usually with high > * impedance to VDD). If the argument is != 0 pull-up is enabled, > * if it is 0, pull-up is disabled. > @@ -76,6 +78,7 @@ > enum pin_config_param { > PIN_CONFIG_BIAS_DISABLE, > PIN_CONFIG_BIAS_HIGH_IMPEDANCE, > + PIN_CONFIG_BIAS_AUTO_PULL, > PIN_CONFIG_BIAS_PULL_UP, > PIN_CONFIG_BIAS_PULL_DOWN, > PIN_CONFIG_DRIVE_PUSH_PULL, > -- > 1.7.10.4 >
On Mon, Feb 11, 2013 at 6:10 PM, Haojian Zhuang <haojian.zhuang@linaro.org> wrote: > There's only one bit to control pin bias as enabled or disabled for some > pins in OMAP SoC. So append PIN_CONFIG_BIAS_AUTO_PULL for this case. > User shouldn't switch pin state between AUTO_PULL and PULL_UP/PULL_DOWN, > since they're similiar concepts. > > Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org> Makes perfect sense. Patch applied with Tony's ACK! Yours, Linus Walleij
* Linus Walleij <linus.walleij@linaro.org> [130215 00:58]: > On Mon, Feb 11, 2013 at 6:10 PM, Haojian Zhuang > <haojian.zhuang@linaro.org> wrote: > > > There's only one bit to control pin bias as enabled or disabled for some > > pins in OMAP SoC. So append PIN_CONFIG_BIAS_AUTO_PULL for this case. > > User shouldn't switch pin state between AUTO_PULL and PULL_UP/PULL_DOWN, > > since they're similiar concepts. > > > > Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org> > > Makes perfect sense. > Patch applied with Tony's ACK! Sorry the conclusion was that this probably won't be needed and can probably be done with just PULL_UP/PULL_DOWN. So can you please drop or revert this AUTO_PULL one? Regards, Tony
On Fri, Feb 15, 2013 at 5:37 PM, Tony Lindgren <tony@atomide.com> wrote: > * Linus Walleij <linus.walleij@linaro.org> [130215 00:58]: >> On Mon, Feb 11, 2013 at 6:10 PM, Haojian Zhuang >> <haojian.zhuang@linaro.org> wrote: >> >> > There's only one bit to control pin bias as enabled or disabled for some >> > pins in OMAP SoC. So append PIN_CONFIG_BIAS_AUTO_PULL for this case. >> > User shouldn't switch pin state between AUTO_PULL and PULL_UP/PULL_DOWN, >> > since they're similiar concepts. >> > >> > Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org> >> >> Makes perfect sense. >> Patch applied with Tony's ACK! > > Sorry the conclusion was that this probably won't be needed and can > probably be done with just PULL_UP/PULL_DOWN. > > So can you please drop or revert this AUTO_PULL one? Sorry I was drunk or something. I never applied this patch, I applied the other one, with the title "pinctrl: generic: rename input schmitt disable". This one stays out. Yours, Linus Walleij
* Linus Walleij <linus.walleij@linaro.org> [130215 12:58]: > On Fri, Feb 15, 2013 at 5:37 PM, Tony Lindgren <tony@atomide.com> wrote: > > * Linus Walleij <linus.walleij@linaro.org> [130215 00:58]: > >> On Mon, Feb 11, 2013 at 6:10 PM, Haojian Zhuang > >> <haojian.zhuang@linaro.org> wrote: > >> > >> > There's only one bit to control pin bias as enabled or disabled for some > >> > pins in OMAP SoC. So append PIN_CONFIG_BIAS_AUTO_PULL for this case. > >> > User shouldn't switch pin state between AUTO_PULL and PULL_UP/PULL_DOWN, > >> > since they're similiar concepts. > >> > > >> > Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org> > >> > >> Makes perfect sense. > >> Patch applied with Tony's ACK! > > > > Sorry the conclusion was that this probably won't be needed and can > > probably be done with just PULL_UP/PULL_DOWN. > > > > So can you please drop or revert this AUTO_PULL one? > > Sorry I was drunk or something. > > I never applied this patch, I applied the other one, > with the title "pinctrl: generic: rename input schmitt disable". > > This one stays out. OK thanks for clarifying it :) Tony
diff --git a/drivers/pinctrl/pinconf-generic.c b/drivers/pinctrl/pinconf-generic.c index ef24230..4a67848 100644 --- a/drivers/pinctrl/pinconf-generic.c +++ b/drivers/pinctrl/pinconf-generic.c @@ -37,6 +37,7 @@ struct pin_config_item { struct pin_config_item conf_items[] = { PCONFDUMP(PIN_CONFIG_BIAS_DISABLE, "input bias disabled", NULL), PCONFDUMP(PIN_CONFIG_BIAS_HIGH_IMPEDANCE, "input bias high impedance", NULL), + PCONFDUMP(PIN_CONFIG_BIAS_AUTO_PULL, "input bias auto pull", NULL), PCONFDUMP(PIN_CONFIG_BIAS_PULL_UP, "input bias pull up", NULL), PCONFDUMP(PIN_CONFIG_BIAS_PULL_DOWN, "input bias pull down", NULL), PCONFDUMP(PIN_CONFIG_DRIVE_PUSH_PULL, "output drive push pull", NULL), diff --git a/include/linux/pinctrl/pinconf-generic.h b/include/linux/pinctrl/pinconf-generic.h index 3e7909a..f2daff4 100644 --- a/include/linux/pinctrl/pinconf-generic.h +++ b/include/linux/pinctrl/pinconf-generic.h @@ -29,6 +29,8 @@ * if for example some other pin is going to drive the signal connected * to it for a while. Pins used for input are usually always high * impedance. + * @PIN_CONFIG_BIAS_AUTO_PULL: the pin will be pulled without specifying + * pull-up or pull-down. * @PIN_CONFIG_BIAS_PULL_UP: the pin will be pulled up (usually with high * impedance to VDD). If the argument is != 0 pull-up is enabled, * if it is 0, pull-up is disabled. @@ -76,6 +78,7 @@ enum pin_config_param { PIN_CONFIG_BIAS_DISABLE, PIN_CONFIG_BIAS_HIGH_IMPEDANCE, + PIN_CONFIG_BIAS_AUTO_PULL, PIN_CONFIG_BIAS_PULL_UP, PIN_CONFIG_BIAS_PULL_DOWN, PIN_CONFIG_DRIVE_PUSH_PULL,
There's only one bit to control pin bias as enabled or disabled for some pins in OMAP SoC. So append PIN_CONFIG_BIAS_AUTO_PULL for this case. User shouldn't switch pin state between AUTO_PULL and PULL_UP/PULL_DOWN, since they're similiar concepts. Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org> --- drivers/pinctrl/pinconf-generic.c | 1 + include/linux/pinctrl/pinconf-generic.h | 3 +++ 2 files changed, 4 insertions(+)