@@ -65,6 +65,29 @@ The following are only applicable to OMAP3+ and AM335x:
- gpmc,wr-access
- gpmc,wr-data-mux-bus
+GPMC chip-select settings properties for child nodes. All are optional.
+
+- gpmc,burst-length Page/burst length. Must be 4, 8 or 16.
+- gpmc,burst-wrap Enables wrap bursting
+- gpmc,burst-read Enables read page/burst mode
+- gpmc,burst-write Enables write page/burst mode
+- gpmc,device-nand Device is NAND
+- gpmc,device-width Total width of device(s) connected to a GPMC
+ chip-select in bytes. The GPMC supports 8-bit
+ and 16-bit devices and so this property must be
+ 1 or 2.
+- gpmc,mux-add-data Address and data multiplexing configuration.
+ Valid values are 1 for address-address-data
+ multiplexing mode and 2 for address-data
+ multiplexing mode.
+- gpmc,sync-read Enables synchronous read. Defaults to asynchronous
+ is this is not set.
+- gpmc,sync-write Enables synchronous writes. Defaults to asynchronous
+ is this is not set.
+- gpmc,wait-pin Wait-pin used by client. Must be less than
+ "gpmc,num-waitpins".
+- gpmc,wait-on-read Enables wait monitoring on reads.
+- gpmc,wait-on-write Enables wait monitoring on writes.
Example for an AM33xx board:
@@ -1190,6 +1190,55 @@ static struct of_device_id gpmc_dt_ids[] = {
};
MODULE_DEVICE_TABLE(of, gpmc_dt_ids);
+/**
+ * gpmc_read_settings_dt - read gpmc settings from device-tree
+ * @np: pointer to device-tree node for a gpmc child device
+ * @p: pointer to gpmc settings structure
+ *
+ * Reads the GPMC settings for a GPMC child device from device-tree and
+ * stores them in the GPMC settings structure passed. The GPMC settings
+ * structure is initialise to zero by this function and so any previously
+ * stored settings will be clearer.
+ */
+void gpmc_read_settings_dt(struct device_node *np, struct gpmc_settings *p)
+{
+ memset(p, 0, sizeof(struct gpmc_settings));
+
+ if (of_find_property(np, "gpmc,sync-read", NULL))
+ p->sync_read = true;
+ if (of_find_property(np, "gpmc,sync-write", NULL))
+ p->sync_write = true;
+
+ if (!of_property_read_u32(np, "gpmc,burst-length", &p->burst_len)) {
+ if (of_find_property(np, "gpmc,burst-wrap", NULL))
+ p->burst_wrap = true;
+ if (of_find_property(np, "gpmc,burst-read", NULL))
+ p->burst_read = true;
+ if (of_find_property(np, "gpmc,burst-write", NULL))
+ p->burst_write = true;
+ if (!p->burst_read && !p->burst_write)
+ pr_warn("%s: page/burst-length set but not used!\n",
+ __func__);
+ }
+
+ if (!of_property_read_u32(np, "gpmc,wait-pin", &p->wait_pin)) {
+ if (of_find_property(np, "gpmc,wait-on-read", NULL))
+ p->wait_on_read = true;
+ if (of_find_property(np, "gpmc,wait-on-write", NULL))
+ p->wait_on_write = true;
+ if (!p->wait_on_read && !p->wait_on_write)
+ pr_warn("%s: read/write wait monitoring not enabled!\n",
+ __func__);
+ }
+
+ of_property_read_u32(np, "gpmc,device-width", &p->device_width);
+
+ if (of_find_property(np, "gpmc,device-nand", NULL))
+ p->device_nand = true;
+
+ of_property_read_u32(np, "gpmc,mux-add-data", &p->mux_add_data);
+}
+
static void __maybe_unused gpmc_read_timings_dt(struct device_node *np,
struct gpmc_timings *gpmc_t)
{
@@ -225,5 +225,7 @@ extern void gpmc_cs_free(int cs);
extern void omap3_gpmc_save_context(void);
extern void omap3_gpmc_restore_context(void);
extern int gpmc_configure(int cmd, int wval);
+extern void gpmc_read_settings_dt(struct device_node *np,
+ struct gpmc_settings *p);
#endif
Adds a function to read the various GPMC chip-select settings from device-tree and store them in the gpmc_settings structure. Update the GPMC device-tree binding documentation to describe these options. Signed-off-by: Jon Hunter <jon-hunter@ti.com> --- Documentation/devicetree/bindings/bus/ti-gpmc.txt | 23 ++++++++++ arch/arm/mach-omap2/gpmc.c | 49 +++++++++++++++++++++ arch/arm/mach-omap2/gpmc.h | 2 + 3 files changed, 74 insertions(+)