@@ -31,6 +31,7 @@
#include <linux/ti_wilink_st.h>
#include <linux/usb/musb.h>
#include <linux/usb/phy.h>
+#include <linux/usb/nop-usb-xceiv.h>
#include <linux/wl12xx.h>
#include <linux/irqchip/arm-gic.h>
#include <linux/platform_data/omap-abe-twl6040.h>
@@ -132,6 +133,22 @@ static struct platform_device btwilink_device = {
.id = -1,
};
+/* PHY device on HS USB Port 1 i.e. nop_usb_xceiv.1 */
+static struct nop_usb_xceiv_platform_data hsusb1_phy_data = {
+ /* FREF_CLK3 provides the 19.2 MHz reference clock to the PHY */
+ .clk_rate = 19200000,
+};
+
+static struct usbhs_phy_data phy_data[] __initdata = {
+ {
+ .port = 1,
+ .reset_gpio = GPIO_HUB_NRESET,
+ .vcc_gpio = GPIO_HUB_POWER,
+ .vcc_polarity = 1,
+ .platform_data = &hsusb1_phy_data,
+ },
+};
+
static struct platform_device *panda_devices[] __initdata = {
&leds_gpio,
&wl1271_device,
@@ -142,49 +159,19 @@ static struct platform_device *panda_devices[] __initdata = {
static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
- .phy_reset = false,
- .reset_gpio_port[0] = -EINVAL,
- .reset_gpio_port[1] = -EINVAL,
- .reset_gpio_port[2] = -EINVAL
-};
-
-static struct gpio panda_ehci_gpios[] __initdata = {
- { GPIO_HUB_POWER, GPIOF_OUT_INIT_LOW, "hub_power" },
- { GPIO_HUB_NRESET, GPIOF_OUT_INIT_LOW, "hub_nreset" },
};
static void __init omap4_ehci_init(void)
{
int ret;
- struct clk *phy_ref_clk;
/* FREF_CLK3 provides the 19.2 MHz reference clock to the PHY */
- phy_ref_clk = clk_get(NULL, "auxclk3_ck");
- if (IS_ERR(phy_ref_clk)) {
- pr_err("Cannot request auxclk3\n");
- return;
- }
- clk_set_rate(phy_ref_clk, 19200000);
- clk_prepare_enable(phy_ref_clk);
-
- /* disable the power to the usb hub prior to init and reset phy+hub */
- ret = gpio_request_array(panda_ehci_gpios,
- ARRAY_SIZE(panda_ehci_gpios));
- if (ret) {
- pr_err("Unable to initialize EHCI power/reset\n");
- return;
- }
-
- gpio_export(GPIO_HUB_POWER, 0);
- gpio_export(GPIO_HUB_NRESET, 0);
- gpio_set_value(GPIO_HUB_NRESET, 1);
+ ret = clk_add_alias("main_clk", "nop_usb_xceiv.1", "auxclk3_ck", NULL);
+ if (ret)
+ pr_err("Failed to add main_clk alias to auxclk3_ck\n");
+ usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
usbhs_init(&usbhs_bdata);
-
- /* enable power to hub */
- gpio_set_value(GPIO_HUB_POWER, 1);
}
static struct omap_musb_board_data musb_board_data = {
Use usbhs_init_phys() to register the PHY's VCC and RESET regulators and the NOP PHY device. Get rid of managing the PHY clock as it will be done by the PHY driver. For that to work we create a clock alias that links the PHY clock name to the PHY device name. Signed-off-by: Roger Quadros <rogerq@ti.com> --- arch/arm/mach-omap2/board-omap4panda.c | 55 ++++++++++++------------------- 1 files changed, 21 insertions(+), 34 deletions(-)