@@ -239,63 +239,6 @@ struct ab8500_platform_data ab8500_platdata = {
.codec = &ab8500_codec_pdata,
};
-/*
- * Thermal Sensor
- */
-
-static struct resource db8500_thsens_resources[] = {
- {
- .name = "IRQ_HOTMON_LOW",
- .start = IRQ_PRCMU_HOTMON_LOW,
- .end = IRQ_PRCMU_HOTMON_LOW,
- .flags = IORESOURCE_IRQ,
- },
- {
- .name = "IRQ_HOTMON_HIGH",
- .start = IRQ_PRCMU_HOTMON_HIGH,
- .end = IRQ_PRCMU_HOTMON_HIGH,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct db8500_thsens_platform_data db8500_thsens_data = {
- .trip_points[0] = {
- .temp = 70000,
- .type = THERMAL_TRIP_ACTIVE,
- .cdev_name = {
- [0] = "thermal-cpufreq-0",
- },
- },
- .trip_points[1] = {
- .temp = 75000,
- .type = THERMAL_TRIP_ACTIVE,
- .cdev_name = {
- [0] = "thermal-cpufreq-0",
- },
- },
- .trip_points[2] = {
- .temp = 80000,
- .type = THERMAL_TRIP_ACTIVE,
- .cdev_name = {
- [0] = "thermal-cpufreq-0",
- },
- },
- .trip_points[3] = {
- .temp = 85000,
- .type = THERMAL_TRIP_CRITICAL,
- },
- .num_trips = 4,
-};
-
-static struct platform_device u8500_thsens_device = {
- .name = "db8500-thermal",
- .resource = db8500_thsens_resources,
- .num_resources = ARRAY_SIZE(db8500_thsens_resources),
- .dev = {
- .platform_data = &db8500_thsens_data,
- },
-};
-
static struct platform_device u8500_cpufreq_cooling_device = {
.name = "db8500-cpufreq-cooling",
};
@@ -656,7 +599,6 @@ static struct platform_device *snowball_platform_devs[] __initdata = {
&snowball_key_dev,
&snowball_sbnet_dev,
&snowball_gpio_en_3v3_regulator_dev,
- &u8500_thsens_device,
&u8500_cpufreq_cooling_device,
&sdi0_regulator,
};
@@ -199,6 +199,8 @@ struct platform_device u8500_ske_keypad_device = {
struct prcmu_pdata db8500_prcmu_pdata = {
.ab_platdata = &ab8500_platdata,
+ .ab_irq = IRQ_DB8500_AB8500,
+ .irq_base = IRQ_PRCMU_BASE,
.version_offset = DB8500_PRCMU_FW_VERSION_OFFSET,
.legacy_offset = DB8500_PRCMU_LEGACY_OFFSET,
};
@@ -109,31 +109,6 @@
/* Virtual interrupts corresponding to the PRCMU wakeups. */
#define IRQ_PRCMU_BASE IRQ_SOC_START
-#define NUM_PRCMU_WAKEUPS (IRQ_PRCMU_END - IRQ_PRCMU_BASE)
-
-#define IRQ_PRCMU_RTC (IRQ_PRCMU_BASE)
-#define IRQ_PRCMU_RTT0 (IRQ_PRCMU_BASE + 1)
-#define IRQ_PRCMU_RTT1 (IRQ_PRCMU_BASE + 2)
-#define IRQ_PRCMU_HSI0 (IRQ_PRCMU_BASE + 3)
-#define IRQ_PRCMU_HSI1 (IRQ_PRCMU_BASE + 4)
-#define IRQ_PRCMU_CA_WAKE (IRQ_PRCMU_BASE + 5)
-#define IRQ_PRCMU_USB (IRQ_PRCMU_BASE + 6)
-#define IRQ_PRCMU_ABB (IRQ_PRCMU_BASE + 7)
-#define IRQ_PRCMU_ABB_FIFO (IRQ_PRCMU_BASE + 8)
-#define IRQ_PRCMU_ARM (IRQ_PRCMU_BASE + 9)
-#define IRQ_PRCMU_MODEM_SW_RESET_REQ (IRQ_PRCMU_BASE + 10)
-#define IRQ_PRCMU_GPIO0 (IRQ_PRCMU_BASE + 11)
-#define IRQ_PRCMU_GPIO1 (IRQ_PRCMU_BASE + 12)
-#define IRQ_PRCMU_GPIO2 (IRQ_PRCMU_BASE + 13)
-#define IRQ_PRCMU_GPIO3 (IRQ_PRCMU_BASE + 14)
-#define IRQ_PRCMU_GPIO4 (IRQ_PRCMU_BASE + 15)
-#define IRQ_PRCMU_GPIO5 (IRQ_PRCMU_BASE + 16)
-#define IRQ_PRCMU_GPIO6 (IRQ_PRCMU_BASE + 17)
-#define IRQ_PRCMU_GPIO7 (IRQ_PRCMU_BASE + 18)
-#define IRQ_PRCMU_GPIO8 (IRQ_PRCMU_BASE + 19)
-#define IRQ_PRCMU_CA_SLEEP (IRQ_PRCMU_BASE + 20)
-#define IRQ_PRCMU_HOTMON_LOW (IRQ_PRCMU_BASE + 21)
-#define IRQ_PRCMU_HOTMON_HIGH (IRQ_PRCMU_BASE + 22)
#define IRQ_PRCMU_END (IRQ_PRCMU_BASE + 23)
/*
@@ -33,7 +33,7 @@
#include <linux/regulator/machine.h>
#include <linux/cpufreq.h>
#include <linux/platform_data/ux500_wdt.h>
-#include <mach/irqs.h>
+#include <linux/platform_data/db8500_thermal.h>
#include "dbx500-prcmu-regs.h"
/* Index of different voltages to be used when accessing AVSData */
@@ -273,8 +273,34 @@ static struct irq_domain *db8500_irq_domain;
* the bits in the bit field are not. (The bits also have a tendency to move
* around, to further complicate matters.)
*/
-#define IRQ_INDEX(_name) ((IRQ_PRCMU_##_name) - IRQ_PRCMU_BASE)
+#define IRQ_INDEX(_name) ((IRQ_PRCMU_##_name))
#define IRQ_ENTRY(_name)[IRQ_INDEX(_name)] = (WAKEUP_BIT_##_name)
+
+#define IRQ_PRCMU_RTC 0
+#define IRQ_PRCMU_RTT0 1
+#define IRQ_PRCMU_RTT1 2
+#define IRQ_PRCMU_HSI0 3
+#define IRQ_PRCMU_HSI1 4
+#define IRQ_PRCMU_CA_WAKE 5
+#define IRQ_PRCMU_USB 6
+#define IRQ_PRCMU_ABB 7
+#define IRQ_PRCMU_ABB_FIFO 8
+#define IRQ_PRCMU_ARM 9
+#define IRQ_PRCMU_MODEM_SW_RESET_REQ 10
+#define IRQ_PRCMU_GPIO0 11
+#define IRQ_PRCMU_GPIO1 12
+#define IRQ_PRCMU_GPIO2 13
+#define IRQ_PRCMU_GPIO3 14
+#define IRQ_PRCMU_GPIO4 15
+#define IRQ_PRCMU_GPIO5 16
+#define IRQ_PRCMU_GPIO6 17
+#define IRQ_PRCMU_GPIO7 18
+#define IRQ_PRCMU_GPIO8 19
+#define IRQ_PRCMU_CA_SLEEP 20
+#define IRQ_PRCMU_HOTMON_LOW 21
+#define IRQ_PRCMU_HOTMON_HIGH 22
+#define NUM_PRCMU_WAKEUPS 23
+
static u32 prcmu_irq_bit[NUM_PRCMU_WAKEUPS] = {
IRQ_ENTRY(RTC),
IRQ_ENTRY(RTT0),
@@ -2649,14 +2675,13 @@ static struct irq_domain_ops db8500_irq_ops = {
.xlate = irq_domain_xlate_twocell,
};
-static int db8500_irq_init(struct device_node *np)
+static int db8500_irq_init(struct device_node *np, int irq_base)
{
- int irq_base = 0;
int i;
/* In the device tree case, just take some IRQs */
if (!np)
- irq_base = IRQ_PRCMU_BASE;
+ irq_base = 0;
db8500_irq_domain = irq_domain_add_simple(
np, NUM_PRCMU_WAKEUPS, irq_base,
@@ -2717,7 +2742,7 @@ void __init db8500_prcmu_early_init(u32 phy_base, u32 size)
* subsequently replaces with a real remap. After the merge of
* the mailbox subsystem all of this early code goes away, and the
* clock driver can probe independently. An early initcall will
- * still be needed, but it can be diverted into drivers/clk/ux500/*.
+ * still be needed, but it can be diverted into drivers/clk/ux500/.
*/
prcmu_base = ioremap(phy_base, size);
if (!prcmu_base)
@@ -2988,18 +3013,57 @@ static struct regulator_init_data db8500_regulators[DB8500_NUM_REGULATORS] = {
},
};
-static struct resource ab8500_resources[] = {
- [0] = {
- .start = IRQ_DB8500_AB8500,
- .end = IRQ_DB8500_AB8500,
- .flags = IORESOURCE_IRQ
- }
-};
-
static struct ux500_wdt_data db8500_wdt_pdata = {
.timeout = 600, /* 10 minutes */
.has_28_bits_resolution = true,
};
+/*
+ * Thermal Sensor
+ */
+
+static struct resource db8500_thsens_resources[] = {
+ {
+ .name = "IRQ_HOTMON_LOW",
+ .start = IRQ_PRCMU_HOTMON_LOW,
+ .end = IRQ_PRCMU_HOTMON_LOW,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .name = "IRQ_HOTMON_HIGH",
+ .start = IRQ_PRCMU_HOTMON_HIGH,
+ .end = IRQ_PRCMU_HOTMON_HIGH,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct db8500_thsens_platform_data db8500_thsens_data = {
+ .trip_points[0] = {
+ .temp = 70000,
+ .type = THERMAL_TRIP_ACTIVE,
+ .cdev_name = {
+ [0] = "thermal-cpufreq-0",
+ },
+ },
+ .trip_points[1] = {
+ .temp = 75000,
+ .type = THERMAL_TRIP_ACTIVE,
+ .cdev_name = {
+ [0] = "thermal-cpufreq-0",
+ },
+ },
+ .trip_points[2] = {
+ .temp = 80000,
+ .type = THERMAL_TRIP_ACTIVE,
+ .cdev_name = {
+ [0] = "thermal-cpufreq-0",
+ },
+ },
+ .trip_points[3] = {
+ .temp = 85000,
+ .type = THERMAL_TRIP_CRITICAL,
+ },
+ .num_trips = 4,
+};
static struct mfd_cell db8500_prcmu_devs[] = {
{
@@ -3021,11 +3085,10 @@ static struct mfd_cell db8500_prcmu_devs[] = {
.id = -1,
},
{
- .name = "ab8500-core",
- .of_compatible = "stericsson,ab8500",
- .num_resources = ARRAY_SIZE(ab8500_resources),
- .resources = ab8500_resources,
- .id = AB8500_VERSION_AB8500,
+ .name = "db8500-thermal",
+ .num_resources = ARRAY_SIZE(db8500_thsens_resources),
+ .resources = db8500_thsens_resources,
+ .platform_data = &db8500_thsens_data,
},
};
@@ -3037,6 +3100,24 @@ static void db8500_prcmu_update_cpufreq(void)
}
}
+static int db8500_prcmu_register_ab8500(struct device *parent,
+ struct ab8500_platform_data *pdata,
+ int irq)
+{
+ struct resource ab8500_resource = DEFINE_RES_IRQ(irq);
+ struct mfd_cell ab8500_cell = {
+ .name = "ab8500-core",
+ .of_compatible = "stericsson,ab8500",
+ .id = AB8500_VERSION_AB8500,
+ .platform_data = pdata,
+ .pdata_size = sizeof(struct ab8500_platform_data),
+ .resources = &ab8500_resource,
+ .num_resources = 1,
+ };
+
+ return mfd_add_devices(parent, 0, &ab8500_cell, 1, NULL, 0, NULL);
+}
+
/**
* prcmu_fw_init - arch init call for the Linux PRCMU fw init logic
*
@@ -3045,7 +3126,7 @@ static int db8500_prcmu_probe(struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node;
struct prcmu_pdata *pdata = dev_get_platdata(&pdev->dev);
- int irq = 0, err = 0, i;
+ int irq = 0, err = 0;
struct resource *res;
res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "prcmu");
@@ -3086,26 +3167,27 @@ static int db8500_prcmu_probe(struct platform_device *pdev)
goto no_irq_return;
}
- db8500_irq_init(np);
-
- for (i = 0; i < ARRAY_SIZE(db8500_prcmu_devs); i++) {
- if (!strcmp(db8500_prcmu_devs[i].name, "ab8500-core")) {
- db8500_prcmu_devs[i].platform_data = pdata->ab_platdata;
- db8500_prcmu_devs[i].pdata_size = sizeof(struct ab8500_platform_data);
- }
- }
+ db8500_irq_init(np, pdata->irq_base);
prcmu_config_esram0_deep_sleep(ESRAM0_DEEP_SLEEP_STATE_RET);
db8500_prcmu_update_cpufreq();
err = mfd_add_devices(&pdev->dev, 0, db8500_prcmu_devs,
- ARRAY_SIZE(db8500_prcmu_devs), NULL, 0, NULL);
+ ARRAY_SIZE(db8500_prcmu_devs), NULL, 0, db8500_irq_domain);
if (err) {
pr_err("prcmu: Failed to add subdevices\n");
return err;
}
+ err = db8500_prcmu_register_ab8500(&pdev->dev, pdata->ab_platdata,
+ pdata->ab_irq);
+ if (err) {
+ mfd_remove_devices(&pdev->dev);
+ pr_err("prcmu: Failed to add ab8500 subdevice\n");
+ goto no_irq_return;
+ }
+
pr_info("DB8500 PRCMU initialized\n");
no_irq_return:
@@ -237,6 +237,8 @@ struct prcmu_pdata
bool enable_set_ddr_opp;
bool enable_ape_opp_100_voltage;
struct ab8500_platform_data *ab_platdata;
+ int ab_irq;
+ int irq_base;
u32 version_offset;
u32 legacy_offset;
u32 adt_offset;
This untangles the final bits of the prcmu code from the platform code: * The IRQ_PRCMU_* definitions move from irqs-db8500.h into prcmu.c because they are only of local significance. * u8500_thsens_device goes into the prcmu, because it uses a PRCMU IRQ that the platform does not see. * IRQ_DB8500_AB8500 and IRQ_PRCMU_BASE go into the platform data because the PRCMU does not see it. Signed-off-by: Arnd Bergmann <arnd@arndb.de> --- arch/arm/mach-ux500/board-mop500.c | 58 ---------- arch/arm/mach-ux500/devices-db8500.c | 2 + arch/arm/mach-ux500/include/mach/irqs-db8500.h | 25 ----- drivers/mfd/db8500-prcmu.c | 140 ++++++++++++++++++++----- include/linux/mfd/dbx500-prcmu.h | 2 + 5 files changed, 115 insertions(+), 112 deletions(-)