@@ -41,7 +41,6 @@
#include <mach/mux.h>
#include <linux/omap-dma.h>
#include <mach/tc.h>
-#include <mach/irda.h>
#include <linux/platform_data/keypad-omap.h>
#include <mach/flash.h>
@@ -50,7 +49,6 @@
#include "common.h"
#include "board-h2.h"
-#include "dma.h"
/* At OMAP1610 Innovator the Ethernet is directly connected to CS1 */
#define OMAP1610_ETHR_START 0x04000300
@@ -276,39 +274,6 @@ static struct platform_device h2_kp_device = {
.resource = h2_kp_resources,
};
-#define H2_IRDA_FIRSEL_GPIO_PIN 17
-
-static struct omap_irda_config h2_irda_data = {
- .transceiver_cap = IR_SIRMODE | IR_MIRMODE | IR_FIRMODE,
- .rx_channel = OMAP_DMA_UART3_RX,
- .tx_channel = OMAP_DMA_UART3_TX,
- .dest_start = UART3_THR,
- .src_start = UART3_RHR,
- .tx_trigger = 0,
- .rx_trigger = 0,
-};
-
-static struct resource h2_irda_resources[] = {
- [0] = {
- .start = INT_UART3,
- .end = INT_UART3,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static u64 irda_dmamask = 0xffffffff;
-
-static struct platform_device h2_irda_device = {
- .name = "omapirda",
- .id = 0,
- .dev = {
- .platform_data = &h2_irda_data,
- .dma_mask = &irda_dmamask,
- },
- .num_resources = ARRAY_SIZE(h2_irda_resources),
- .resource = h2_irda_resources,
-};
-
static struct gpio_led h2_gpio_led_pins[] = {
{
.name = "h2:red",
@@ -339,7 +304,6 @@ static struct platform_device *h2_devices[] __initdata = {
&h2_nor_device,
&h2_nand_device,
&h2_smc91x_device,
- &h2_irda_device,
&h2_kp_device,
&h2_gpio_leds,
};
@@ -38,14 +38,12 @@
#include <mach/mux.h>
#include <mach/tc.h>
#include <linux/omap-dma.h>
-#include <mach/irda.h>
#include <linux/platform_data/keypad-omap.h>
#include <mach/hardware.h>
#include <mach/usb.h>
#include "common.h"
-#include "dma.h"
#define PALMTE_USBDETECT_GPIO 0
#define PALMTE_USB_OR_DC_GPIO 1
@@ -167,40 +165,11 @@ static struct platform_device palmte_backlight_device = {
},
};
-static struct omap_irda_config palmte_irda_config = {
- .transceiver_cap = IR_SIRMODE,
- .rx_channel = OMAP_DMA_UART3_RX,
- .tx_channel = OMAP_DMA_UART3_TX,
- .dest_start = UART3_THR,
- .src_start = UART3_RHR,
- .tx_trigger = 0,
- .rx_trigger = 0,
-};
-
-static struct resource palmte_irda_resources[] = {
- [0] = {
- .start = INT_UART3,
- .end = INT_UART3,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device palmte_irda_device = {
- .name = "omapirda",
- .id = -1,
- .dev = {
- .platform_data = &palmte_irda_config,
- },
- .num_resources = ARRAY_SIZE(palmte_irda_resources),
- .resource = palmte_irda_resources,
-};
-
static struct platform_device *palmte_devices[] __initdata = {
&palmte_rom_device,
&palmte_kp_device,
&palmte_lcd_device,
&palmte_backlight_device,
- &palmte_irda_device,
};
static struct omap_usb_config palmte_usb_config __initdata = {
@@ -38,14 +38,12 @@
#include <mach/mux.h>
#include <linux/omap-dma.h>
#include <mach/tc.h>
-#include <mach/irda.h>
#include <linux/platform_data/keypad-omap.h>
#include <mach/hardware.h>
#include <mach/usb.h>
#include "common.h"
-#include "dma.h"
#define PALMTT_USBDETECT_GPIO 0
#define PALMTT_CABLE_GPIO 1
@@ -163,33 +161,6 @@ static struct platform_device palmtt_lcd_device = {
.name = "lcd_palmtt",
.id = -1,
};
-static struct omap_irda_config palmtt_irda_config = {
- .transceiver_cap = IR_SIRMODE,
- .rx_channel = OMAP_DMA_UART3_RX,
- .tx_channel = OMAP_DMA_UART3_TX,
- .dest_start = UART3_THR,
- .src_start = UART3_RHR,
- .tx_trigger = 0,
- .rx_trigger = 0,
-};
-
-static struct resource palmtt_irda_resources[] = {
- [0] = {
- .start = INT_UART3,
- .end = INT_UART3,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device palmtt_irda_device = {
- .name = "omapirda",
- .id = -1,
- .dev = {
- .platform_data = &palmtt_irda_config,
- },
- .num_resources = ARRAY_SIZE(palmtt_irda_resources),
- .resource = palmtt_irda_resources,
-};
static struct platform_device palmtt_spi_device = {
.name = "spi_palmtt",
@@ -234,7 +205,6 @@ static struct platform_device *palmtt_devices[] __initdata = {
&palmtt_flash_device,
&palmtt_kp_device,
&palmtt_lcd_device,
- &palmtt_irda_device,
&palmtt_spi_device,
&palmtt_backlight_device,
&palmtt_led_device,
@@ -40,14 +40,12 @@
#include <mach/mux.h>
#include <linux/omap-dma.h>
#include <mach/tc.h>
-#include <mach/irda.h>
#include <linux/platform_data/keypad-omap.h>
#include <mach/hardware.h>
#include <mach/usb.h>
#include "common.h"
-#include "dma.h"
#define PALMZ71_USBDETECT_GPIO 0
#define PALMZ71_PENIRQ_GPIO 6
@@ -153,34 +151,6 @@ static struct platform_device palmz71_lcd_device = {
.id = -1,
};
-static struct omap_irda_config palmz71_irda_config = {
- .transceiver_cap = IR_SIRMODE,
- .rx_channel = OMAP_DMA_UART3_RX,
- .tx_channel = OMAP_DMA_UART3_TX,
- .dest_start = UART3_THR,
- .src_start = UART3_RHR,
- .tx_trigger = 0,
- .rx_trigger = 0,
-};
-
-static struct resource palmz71_irda_resources[] = {
- [0] = {
- .start = INT_UART3,
- .end = INT_UART3,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device palmz71_irda_device = {
- .name = "omapirda",
- .id = -1,
- .dev = {
- .platform_data = &palmz71_irda_config,
- },
- .num_resources = ARRAY_SIZE(palmz71_irda_resources),
- .resource = palmz71_irda_resources,
-};
-
static struct platform_device palmz71_spi_device = {
.name = "spi_palmz71",
.id = -1,
@@ -202,7 +172,6 @@ static struct platform_device *devices[] __initdata = {
&palmz71_rom_device,
&palmz71_kp_device,
&palmz71_lcd_device,
- &palmz71_irda_device,
&palmz71_spi_device,
&palmz71_backlight_device,
};
@@ -37,7 +37,6 @@
#include <mach/flash.h>
#include <mach/mux.h>
#include <linux/omap-dma.h>
-#include <mach/irda.h>
#include <mach/tc.h>
#include <mach/board-sx1.h>
@@ -45,7 +44,6 @@
#include <mach/usb.h>
#include "common.h"
-#include "dma.h"
/* Write to I2C device */
int sx1_i2c_write_byte(u8 devaddr, u8 regoffset, u8 value)
@@ -228,39 +226,6 @@ static struct platform_device sx1_kp_device = {
.resource = sx1_kp_resources,
};
-/*----------- IRDA -------------------------*/
-
-static struct omap_irda_config sx1_irda_data = {
- .transceiver_cap = IR_SIRMODE,
- .rx_channel = OMAP_DMA_UART3_RX,
- .tx_channel = OMAP_DMA_UART3_TX,
- .dest_start = UART3_THR,
- .src_start = UART3_RHR,
- .tx_trigger = 0,
- .rx_trigger = 0,
-};
-
-static struct resource sx1_irda_resources[] = {
- [0] = {
- .start = INT_UART3,
- .end = INT_UART3,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static u64 irda_dmamask = 0xffffffff;
-
-static struct platform_device sx1_irda_device = {
- .name = "omapirda",
- .id = 0,
- .dev = {
- .platform_data = &sx1_irda_data,
- .dma_mask = &irda_dmamask,
- },
- .num_resources = ARRAY_SIZE(sx1_irda_resources),
- .resource = sx1_irda_resources,
-};
-
/*----------- MTD -------------------------*/
static struct mtd_partition sx1_partitions[] = {
@@ -366,7 +331,6 @@ static struct omap_lcd_config sx1_lcd_config __initdata = {
static struct platform_device *sx1_devices[] __initdata = {
&sx1_flash_device,
&sx1_kp_device,
- &sx1_irda_device,
};
/*-----------------------------------------*/
@@ -20,8 +20,6 @@
#define __OMAP1_DMA_CHANNEL_H
/* DMA channels for omap1 */
-#define OMAP_DMA_UART3_TX 18
-#define OMAP_DMA_UART3_RX 19
/* These are only for 1610 */
deleted file mode 100644
@@ -1,33 +0,0 @@
-/*
- * arch/arm/plat-omap/include/mach/irda.h
- *
- * Copyright (C) 2005-2006 Komal Shah <komal_shah802003@yahoo.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#ifndef ASMARM_ARCH_IRDA_H
-#define ASMARM_ARCH_IRDA_H
-
-/* board specific transceiver capabilities */
-
-#define IR_SEL 1 /* Selects IrDA */
-#define IR_SIRMODE 2
-#define IR_FIRMODE 4
-#define IR_MIRMODE 8
-
-struct omap_irda_config {
- int transceiver_cap;
- int (*transceiver_mode)(struct device *dev, int mode);
- int (*select_irda)(struct device *dev, int state);
- int rx_channel;
- int tx_channel;
- unsigned long dest_start;
- unsigned long src_start;
- int tx_trigger;
- int rx_trigger;
- int mode;
-};
-
-#endif
omap-ir.c driver has never been upstream and was also removed from linux-omap.git four years ago (See linux-omap.git commit efd1e3f ("REMOVE OMAP LEGACY CODE: Reset drivers/net/irda to mainline")). Therefore remove needless device registration from a few board files and delete thus to be unused arch/arm/mach-omap1/include/mach/irda.h and unused OMAP_DMA_UART3_* definitions from dma.h. Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com> --- arch/arm/mach-omap1/board-h2.c | 36 ------------------------------- arch/arm/mach-omap1/board-palmte.c | 31 -------------------------- arch/arm/mach-omap1/board-palmtt.c | 30 -------------------------- arch/arm/mach-omap1/board-palmz71.c | 31 -------------------------- arch/arm/mach-omap1/board-sx1.c | 36 ------------------------------- arch/arm/mach-omap1/dma.h | 2 -- arch/arm/mach-omap1/include/mach/irda.h | 33 ---------------------------- 7 files changed, 199 deletions(-) delete mode 100644 arch/arm/mach-omap1/include/mach/irda.h