diff mbox

[2/2] arm: mach-imx: anatop: add two APIs for USB driver

Message ID 1376292414-22922-2-git-send-email-peter.chen@freescale.com (mailing list archive)
State New, archived
Headers show

Commit Message

Peter Chen Aug. 12, 2013, 7:26 a.m. UTC
imx_anatop_usb1_disconnect_line is used to disconnect dp/dm between
PHY and controller, after that, the controller always gets SE0
for the status of dp/dm, it is not any wakeup signal for controller.
It is used to avoid unknown interrupt due to dp/dm is floading
after the USB PHY is no powered when there is no vbus supplied.

imx_anatop_set_stop_mode_config is used to keep internal regualtor on
when the system enters suspend mode, it will increase power consumption,
we only enable it when the user enables USB wakeup (default is off).

Signed-off-by: Peter Chen <peter.chen@freescale.com>
---
 arch/arm/mach-imx/anatop.c |   22 ++++++++++++++++++++++
 arch/arm/mach-imx/common.h |    2 ++
 2 files changed, 24 insertions(+), 0 deletions(-)

Comments

Shawn Guo Aug. 14, 2013, 3:47 a.m. UTC | #1
On Mon, Aug 12, 2013 at 03:26:54PM +0800, Peter Chen wrote:
> imx_anatop_usb1_disconnect_line is used to disconnect dp/dm between
> PHY and controller, after that, the controller always gets SE0
> for the status of dp/dm, it is not any wakeup signal for controller.
> It is used to avoid unknown interrupt due to dp/dm is floading
> after the USB PHY is no powered when there is no vbus supplied.
> 
> imx_anatop_set_stop_mode_config is used to keep internal regualtor on
> when the system enters suspend mode, it will increase power consumption,
> we only enable it when the user enables USB wakeup (default is off).
> 
> Signed-off-by: Peter Chen <peter.chen@freescale.com>
> ---
>  arch/arm/mach-imx/anatop.c |   22 ++++++++++++++++++++++
>  arch/arm/mach-imx/common.h |    2 ++
>  2 files changed, 24 insertions(+), 0 deletions(-)
> 
> diff --git a/arch/arm/mach-imx/anatop.c b/arch/arm/mach-imx/anatop.c
> index 71f1a08..7f96bbc 100644
> --- a/arch/arm/mach-imx/anatop.c
> +++ b/arch/arm/mach-imx/anatop.c
> @@ -26,6 +26,7 @@
>  #define ANADIG_ANA_MISC0	0x150
>  #define ANADIG_ANA_MISC2	0x170
>  #define ANADIG_USB1_CHRG_DETECT	0x1b0
> +#define ANADIG_USB1_LOOPBACK	0x1e0
>  #define ANADIG_USB2_CHRG_DETECT	0x210
>  #define ANADIG_DIGPROG		0x260
>  
> @@ -34,6 +35,8 @@
>  #define BM_ANADIG_ANA_MISC0_STOP_MODE_CONFIG	0x1000
>  #define BM_ANADIG_USB_CHRG_DETECT_CHK_CHRG_B	0x80000
>  #define BM_ANADIG_USB_CHRG_DETECT_EN_B		0x100000
> +#define BM_ANADIG_USB1_LOOPBACK_UTMI_DIG_TST1	0x00000004
> +#define BM_ANADIG_USB1_LOOPBACK_TSTI_TX_EN	0x00000020
>  
>  #define ANADIG_ANA_MISC2_REG1_STEP_OFFSET	26
>  #define ANADIG_ANA_MISC2_REG_STEP_MASK		0x3
> @@ -142,6 +145,25 @@ u32 imx_anatop_get_digprog(void)
>  	return digprog;
>  }
>  
> +void imx_anatop_usb1_disconnect_line(bool enable)
> +{
> +	if (enable)
> +		regmap_write(anatop, ANADIG_USB1_LOOPBACK,
> +			BM_ANADIG_USB1_LOOPBACK_UTMI_DIG_TST1 |
> +				BM_ANADIG_USB1_LOOPBACK_TSTI_TX_EN);
> +	else
> +		regmap_write(anatop, ANADIG_USB1_LOOPBACK, 0);
> +}
> +EXPORT_SYMBOL(imx_anatop_usb1_disconnect_line);
> +
> +void imx_anatop_set_stop_mode_config(bool enable)
> +{
> +	regmap_write(anatop, ANADIG_ANA_MISC0 +
> +		(enable ? REG_SET : REG_CLR),
> +			BM_ANADIG_ANA_MISC0_STOP_MODE_CONFIG);
> +}
> +EXPORT_SYMBOL(imx_anatop_set_stop_mode_config);
> +

Where do you want to call these two functions from?

Shawn

>  void __init imx_anatop_init(void)
>  {
>  	anatop = syscon_regmap_lookup_by_compatible("fsl,imx6q-anatop");
> diff --git a/arch/arm/mach-imx/common.h b/arch/arm/mach-imx/common.h
> index df1d7b0..dcb3305 100644
> --- a/arch/arm/mach-imx/common.h
> +++ b/arch/arm/mach-imx/common.h
> @@ -137,6 +137,8 @@ extern void imx_anatop_init(void);
>  extern void imx_anatop_pre_suspend(void);
>  extern void imx_anatop_post_resume(void);
>  extern u32 imx_anatop_get_digprog(void);
> +extern void imx_anatop_usb1_disconnect_line(bool);
> +extern void imx_anatop_set_stop_mode_config(bool);
>  extern int imx6q_set_lpm(enum mxc_cpu_pwr_mode mode);
>  extern void imx6q_set_chicken_bit(void);
>  
> -- 
> 1.7.1
> 
>
Peter Chen Aug. 14, 2013, 3:50 a.m. UTC | #2
On Wed, Aug 14, 2013 at 11:47:56AM +0800, Shawn Guo wrote:
> On Mon, Aug 12, 2013 at 03:26:54PM +0800, Peter Chen wrote:
> > imx_anatop_usb1_disconnect_line is used to disconnect dp/dm between
> > PHY and controller, after that, the controller always gets SE0
> > for the status of dp/dm, it is not any wakeup signal for controller.
> > It is used to avoid unknown interrupt due to dp/dm is floading
> > after the USB PHY is no powered when there is no vbus supplied.
> > 
> > imx_anatop_set_stop_mode_config is used to keep internal regualtor on
> > when the system enters suspend mode, it will increase power consumption,
> > we only enable it when the user enables USB wakeup (default is off).
> > 
> > Signed-off-by: Peter Chen <peter.chen@freescale.com>
> > ---
> >  arch/arm/mach-imx/anatop.c |   22 ++++++++++++++++++++++
> >  arch/arm/mach-imx/common.h |    2 ++
> >  2 files changed, 24 insertions(+), 0 deletions(-)
> > 
> > diff --git a/arch/arm/mach-imx/anatop.c b/arch/arm/mach-imx/anatop.c
> > index 71f1a08..7f96bbc 100644
> > --- a/arch/arm/mach-imx/anatop.c
> > +++ b/arch/arm/mach-imx/anatop.c
> > @@ -26,6 +26,7 @@
> >  #define ANADIG_ANA_MISC0	0x150
> >  #define ANADIG_ANA_MISC2	0x170
> >  #define ANADIG_USB1_CHRG_DETECT	0x1b0
> > +#define ANADIG_USB1_LOOPBACK	0x1e0
> >  #define ANADIG_USB2_CHRG_DETECT	0x210
> >  #define ANADIG_DIGPROG		0x260
> >  
> > @@ -34,6 +35,8 @@
> >  #define BM_ANADIG_ANA_MISC0_STOP_MODE_CONFIG	0x1000
> >  #define BM_ANADIG_USB_CHRG_DETECT_CHK_CHRG_B	0x80000
> >  #define BM_ANADIG_USB_CHRG_DETECT_EN_B		0x100000
> > +#define BM_ANADIG_USB1_LOOPBACK_UTMI_DIG_TST1	0x00000004
> > +#define BM_ANADIG_USB1_LOOPBACK_TSTI_TX_EN	0x00000020
> >  
> >  #define ANADIG_ANA_MISC2_REG1_STEP_OFFSET	26
> >  #define ANADIG_ANA_MISC2_REG_STEP_MASK		0x3
> > @@ -142,6 +145,25 @@ u32 imx_anatop_get_digprog(void)
> >  	return digprog;
> >  }
> >  
> > +void imx_anatop_usb1_disconnect_line(bool enable)
> > +{
> > +	if (enable)
> > +		regmap_write(anatop, ANADIG_USB1_LOOPBACK,
> > +			BM_ANADIG_USB1_LOOPBACK_UTMI_DIG_TST1 |
> > +				BM_ANADIG_USB1_LOOPBACK_TSTI_TX_EN);
> > +	else
> > +		regmap_write(anatop, ANADIG_USB1_LOOPBACK, 0);
> > +}
> > +EXPORT_SYMBOL(imx_anatop_usb1_disconnect_line);
> > +
> > +void imx_anatop_set_stop_mode_config(bool enable)
> > +{
> > +	regmap_write(anatop, ANADIG_ANA_MISC0 +
> > +		(enable ? REG_SET : REG_CLR),
> > +			BM_ANADIG_ANA_MISC0_STOP_MODE_CONFIG);
> > +}
> > +EXPORT_SYMBOL(imx_anatop_set_stop_mode_config);
> > +
> 
> Where do you want to call these two functions from?
> 

From USB driver, the usb driver is possible built as module.
Peter Chen Aug. 14, 2013, 4:51 a.m. UTC | #3
On Wed, Aug 14, 2013 at 02:32:38PM +0800, Shawn Guo wrote:
> On Wed, Aug 14, 2013 at 11:50:07AM +0800, Peter Chen wrote:
> > > > +void imx_anatop_usb1_disconnect_line(bool enable)
> > > > +{
> > > > +	if (enable)
> > > > +		regmap_write(anatop, ANADIG_USB1_LOOPBACK,
> > > > +			BM_ANADIG_USB1_LOOPBACK_UTMI_DIG_TST1 |
> > > > +				BM_ANADIG_USB1_LOOPBACK_TSTI_TX_EN);
> > > > +	else
> > > > +		regmap_write(anatop, ANADIG_USB1_LOOPBACK, 0);
> > > > +}
> > > > +EXPORT_SYMBOL(imx_anatop_usb1_disconnect_line);
> > > > +
> > > > +void imx_anatop_set_stop_mode_config(bool enable)
> > > > +{
> > > > +	regmap_write(anatop, ANADIG_ANA_MISC0 +
> > > > +		(enable ? REG_SET : REG_CLR),
> > > > +			BM_ANADIG_ANA_MISC0_STOP_MODE_CONFIG);
> > > > +}
> > > > +EXPORT_SYMBOL(imx_anatop_set_stop_mode_config);
> > > > +
> > > 
> > > Where do you want to call these two functions from?
> > > 
> > 
> > From USB driver, the usb driver is possible built as module.
> 
> I do not think it's appropriate have device driver directly call into
> platform level functions.

Will do it like thermal and regulator driver, please forget it.
Shawn Guo Aug. 14, 2013, 6:32 a.m. UTC | #4
On Wed, Aug 14, 2013 at 11:50:07AM +0800, Peter Chen wrote:
> > > +void imx_anatop_usb1_disconnect_line(bool enable)
> > > +{
> > > +	if (enable)
> > > +		regmap_write(anatop, ANADIG_USB1_LOOPBACK,
> > > +			BM_ANADIG_USB1_LOOPBACK_UTMI_DIG_TST1 |
> > > +				BM_ANADIG_USB1_LOOPBACK_TSTI_TX_EN);
> > > +	else
> > > +		regmap_write(anatop, ANADIG_USB1_LOOPBACK, 0);
> > > +}
> > > +EXPORT_SYMBOL(imx_anatop_usb1_disconnect_line);
> > > +
> > > +void imx_anatop_set_stop_mode_config(bool enable)
> > > +{
> > > +	regmap_write(anatop, ANADIG_ANA_MISC0 +
> > > +		(enable ? REG_SET : REG_CLR),
> > > +			BM_ANADIG_ANA_MISC0_STOP_MODE_CONFIG);
> > > +}
> > > +EXPORT_SYMBOL(imx_anatop_set_stop_mode_config);
> > > +
> > 
> > Where do you want to call these two functions from?
> > 
> 
> From USB driver, the usb driver is possible built as module.

I do not think it's appropriate have device driver directly call into
platform level functions.

Shawn
diff mbox

Patch

diff --git a/arch/arm/mach-imx/anatop.c b/arch/arm/mach-imx/anatop.c
index 71f1a08..7f96bbc 100644
--- a/arch/arm/mach-imx/anatop.c
+++ b/arch/arm/mach-imx/anatop.c
@@ -26,6 +26,7 @@ 
 #define ANADIG_ANA_MISC0	0x150
 #define ANADIG_ANA_MISC2	0x170
 #define ANADIG_USB1_CHRG_DETECT	0x1b0
+#define ANADIG_USB1_LOOPBACK	0x1e0
 #define ANADIG_USB2_CHRG_DETECT	0x210
 #define ANADIG_DIGPROG		0x260
 
@@ -34,6 +35,8 @@ 
 #define BM_ANADIG_ANA_MISC0_STOP_MODE_CONFIG	0x1000
 #define BM_ANADIG_USB_CHRG_DETECT_CHK_CHRG_B	0x80000
 #define BM_ANADIG_USB_CHRG_DETECT_EN_B		0x100000
+#define BM_ANADIG_USB1_LOOPBACK_UTMI_DIG_TST1	0x00000004
+#define BM_ANADIG_USB1_LOOPBACK_TSTI_TX_EN	0x00000020
 
 #define ANADIG_ANA_MISC2_REG1_STEP_OFFSET	26
 #define ANADIG_ANA_MISC2_REG_STEP_MASK		0x3
@@ -142,6 +145,25 @@  u32 imx_anatop_get_digprog(void)
 	return digprog;
 }
 
+void imx_anatop_usb1_disconnect_line(bool enable)
+{
+	if (enable)
+		regmap_write(anatop, ANADIG_USB1_LOOPBACK,
+			BM_ANADIG_USB1_LOOPBACK_UTMI_DIG_TST1 |
+				BM_ANADIG_USB1_LOOPBACK_TSTI_TX_EN);
+	else
+		regmap_write(anatop, ANADIG_USB1_LOOPBACK, 0);
+}
+EXPORT_SYMBOL(imx_anatop_usb1_disconnect_line);
+
+void imx_anatop_set_stop_mode_config(bool enable)
+{
+	regmap_write(anatop, ANADIG_ANA_MISC0 +
+		(enable ? REG_SET : REG_CLR),
+			BM_ANADIG_ANA_MISC0_STOP_MODE_CONFIG);
+}
+EXPORT_SYMBOL(imx_anatop_set_stop_mode_config);
+
 void __init imx_anatop_init(void)
 {
 	anatop = syscon_regmap_lookup_by_compatible("fsl,imx6q-anatop");
diff --git a/arch/arm/mach-imx/common.h b/arch/arm/mach-imx/common.h
index df1d7b0..dcb3305 100644
--- a/arch/arm/mach-imx/common.h
+++ b/arch/arm/mach-imx/common.h
@@ -137,6 +137,8 @@  extern void imx_anatop_init(void);
 extern void imx_anatop_pre_suspend(void);
 extern void imx_anatop_post_resume(void);
 extern u32 imx_anatop_get_digprog(void);
+extern void imx_anatop_usb1_disconnect_line(bool);
+extern void imx_anatop_set_stop_mode_config(bool);
 extern int imx6q_set_lpm(enum mxc_cpu_pwr_mode mode);
 extern void imx6q_set_chicken_bit(void);