@@ -106,6 +106,13 @@ config AHCI_IMX
If unsure, say N.
+config SATA_XGENE
+ tristate "APM X-Gene 6.0Gbps SATA support"
+ depends on SATA_AHCI_PLATFORM
+ default y if ARM64
+ help
+ This option enables support for APM X-Gene SoC SATA controller.
+
config SATA_FSL
tristate "Freescale 3.0Gbps SATA support"
depends on FSL_SOC
@@ -11,6 +11,8 @@ obj-$(CONFIG_SATA_SIL24) += sata_sil24.o
obj-$(CONFIG_SATA_DWC) += sata_dwc_460ex.o
obj-$(CONFIG_SATA_HIGHBANK) += sata_highbank.o libahci.o
obj-$(CONFIG_AHCI_IMX) += ahci_imx.o
+sata-xgene-objs := sata_xgene.o sata_xgene_serdes.o
+obj-$(CONFIG_SATA_XGENE) += sata-xgene.o
# SFF w/ custom DMA
obj-$(CONFIG_PDC_ADMA) += pdc_adma.o
new file mode 100644
@@ -0,0 +1,1385 @@
+/*
+ * AppliedMicro X-Gene SoC SATA Driver
+ *
+ * Copyright (c) 2013, Applied Micro Circuits Corporation
+ * Author: Loc Ho <lho@apm.com>
+ * Tuan Phan <tphan@apm.com>
+ * Suman Tripathi <stripathi@apm.com>
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/acpi.h>
+#include <linux/efi.h>
+#include "sata_xgene.h"
+
+#undef XGENE_DBG_CSR /* Enable CSR read/write dumping */
+#ifdef XGENE_DBG_CSR
+#define XGENE_CSRDBG(fmt, args...) \
+ printk(KERN_INFO "XGENESATA: " fmt "\n", ## args);
+#else
+#define XGENE_CSRDBG(fmt, args...)
+#endif
+
+/* Max # of disk per a controller */
+#define MAX_AHCI_CHN_PERCTR 2
+
+#define SATA_DIAG_OFFSET 0x0000D000
+#define SATA_GLB_OFFSET 0x0000D850
+#define SATA_SHIM_OFFSET 0x0000E000
+#define SATA_MASTER_OFFSET 0x0000F000
+#define SATA_PORT0_OFFSET 0x00000100
+#define SATA_PORT1_OFFSET 0x00000180
+
+/* SATA host controller CSR */
+#define SLVRDERRATTRIBUTES_ADDR 0x00000000
+#define SLVWRERRATTRIBUTES_ADDR 0x00000004
+#define MSTRDERRATTRIBUTES_ADDR 0x00000008
+#define MSTWRERRATTRIBUTES_ADDR 0x0000000c
+#define BUSCTLREG_ADDR 0x00000014
+#define MSTAWAUX_COHERENT_BYPASS_SET(dst, src) \
+ (((dst) & ~0x00000002) | (((u32)(src)<<1) & 0x00000002))
+#define MSTARAUX_COHERENT_BYPASS_SET(dst, src) \
+ (((dst) & ~0x00000001) | (((u32)(src)) & 0x00000001))
+#define IOFMSTRWAUX_ADDR 0x00000018
+#define INTSTATUSMASK_ADDR 0x0000002c
+#define ERRINTSTATUS_ADDR 0x00000030
+#define ERRINTSTATUSMASK_ADDR 0x00000034
+
+/* SATA host AHCI CSR */
+#define PORTCFG_ADDR 0x000000a4
+#define PORTADDR_SET(dst, src) \
+ (((dst) & ~0x0000003f) | (((u32)(src)) & 0x0000003f))
+#define PORTPHY1CFG_ADDR 0x000000a8
+#define PORTPHY1CFG_FRCPHYRDY_SET(dst, src) \
+ (((dst) & ~0x00100000) | (((u32)(src) << 0x14) & 0x00100000))
+#define PORTPHY2CFG_ADDR 0x000000ac
+#define PORTPHY3CFG_ADDR 0x000000b0
+#define PORTPHY4CFG_ADDR 0x000000b4
+#define PORTPHY5CFG_ADDR 0x000000b8
+#define SCTL0_ADDR 0x0000012C
+#define PORTPHY5CFG_RTCHG_SET(dst, src) \
+ (((dst) & ~0xfff00000) | (((u32)(src) << 0x14) & 0xfff00000))
+#define PORTAXICFG_EN_CONTEXT_SET(dst, src) \
+ (((dst) & ~0x01000000) | (((u32)(src) << 0x18) & 0x01000000))
+#define PORTAXICFG_ADDR 0x000000bc
+#define PORTAXICFG_OUTTRANS_SET(dst, src) \
+ (((dst) & ~0x00f00000) | (((u32)(src) << 0x14) & 0x00f00000))
+
+/* SATA host controller slave CSR */
+#define INT_SLV_TMOMASK_ADDR 0x00000010
+
+/* SATA global diagnostic CSR */
+#define REGSPEC_CFG_MEM_RAM_SHUTDOWN_ADDR 0x00000070
+#define REGSPEC_BLOCK_MEM_RDY_ADDR 0x00000074
+
+/* AHBC IOB flush CSR */
+#define CFG_AMA_MODE_ADDR 0x0000e014
+#define CFG_RD2WR_EN 0x00000002
+
+#define MAX_RETRY_COUNT 3
+#define SATA_RESET_MEM_RAM_TO 100000
+
+void xgene_ahci_in32(void *addr, u32 *val)
+{
+ *val = readl(addr);
+ XGENE_CSRDBG("SATAPHY CSR RD: 0x%p value: 0x%08x", addr, *val);
+}
+
+void xgene_ahci_out32(void *addr, u32 val)
+{
+ writel(val, addr);
+ XGENE_CSRDBG("SATAPHY CSR WR: 0x%p value: 0x%08x", addr, val);
+}
+
+void xgene_ahci_out32_flush(void *addr, u32 val)
+{
+ writel(val, addr);
+ XGENE_CSRDBG("SATAPHY CSR WR: 0x%p value: 0x%08x", addr, val);
+ val = readl(addr);
+}
+
+void xgene_ahci_delayus(unsigned long us)
+{
+ udelay(us);
+}
+
+void xgene_ahci_delayms(unsigned long us)
+{
+ mdelay(us);
+}
+
+static int xgene_ahci_get_channel(struct ata_host *host, struct ata_port *port)
+{
+ int i;
+ for (i = 0; i < host->n_ports; i++)
+ if (host->ports[i] == port)
+ return i;
+ return -1;
+}
+
+int xgene_ahci_init_memram(struct xgene_ahci_context *ctx)
+{
+ void *diagcsr = ctx->csr_base + SATA_DIAG_OFFSET;
+ int timeout;
+ u32 val;
+
+ xgene_ahci_in32(diagcsr + REGSPEC_CFG_MEM_RAM_SHUTDOWN_ADDR, &val);
+ if (val == 0) {
+ dev_dbg(ctx->dev, "already clear memory shutdown\n");
+ return 0;
+ }
+ dev_dbg(ctx->dev, "clear controller %d memory shutdown\n", ctx->cid);
+ /* SATA controller memory in shutdown. Remove from shutdown. */
+ xgene_ahci_out32_flush(diagcsr + REGSPEC_CFG_MEM_RAM_SHUTDOWN_ADDR,
+ 0x00);
+ timeout = SATA_RESET_MEM_RAM_TO;
+ do {
+ xgene_ahci_in32(diagcsr + REGSPEC_BLOCK_MEM_RDY_ADDR, &val);
+ if (val != 0xFFFFFFFF)
+ xgene_ahci_delayus(1);
+ } while (val != 0xFFFFFFFF && timeout-- > 0);
+ if (timeout <= 0) {
+ dev_err(ctx->dev, "failed to remove memory from shutdown\n");
+ return -ENODEV;
+ }
+ return 0;
+}
+
+/*
+ * Custom Query ID command
+ *
+ * Due to HW errata, we must stop and re-start the port state machine after
+ * read ID command.
+ */
+static unsigned int xgene_ahci_read_id(struct ata_device *dev,
+ struct ata_taskfile *tf, u16 *id)
+{
+ u32 err_mask;
+ struct ata_port *ap = dev->link->ap;
+ void *port_mmio = ahci_port_base(ap);
+ u32 data32;
+
+ err_mask = ata_do_dev_read_id(dev, tf, id);
+ if (err_mask)
+ return err_mask;
+
+ /* Mask reserved area. Bit78 spec of Link Power Management
+ * bit15-8: reserved
+ * bit7: NCQ autosence
+ * bit6: Software settings preservation supported
+ * bit5: reserved
+ * bit4: In-order sata delivery supported
+ * bit3: DIPM requests supported
+ * bit2: DMA Setup FIS Auto-Activate optimization supported
+ * bit1: DMA Setup FIX non-Zero buffer offsets supported
+ * bit0: Reserved
+ *
+ * Clear reserved bit (DEVSLP bit) as we don't support DEVSLP
+ */
+ id[78] &= 0x00FF;
+
+ /* Restart the port if requred due to HW errata */
+ data32 = readl(port_mmio + PORT_CMD_ISSUE);
+ if (data32 == 0x00000000) {
+ writel(PORT_CMD_FIS_RX, port_mmio + PORT_CMD);
+ readl(port_mmio + PORT_CMD); /* flush */
+ writel(PORT_CMD_FIS_RX | PORT_CMD_START, port_mmio + PORT_CMD);
+ readl(port_mmio + PORT_CMD); /* flush */
+ }
+ return 0;
+}
+
+static unsigned int xgene_ahci_qc_issue(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ void __iomem *port_mmio = ahci_port_base(ap);
+ struct ahci_port_priv *pp = ap->private_data;
+
+ /* Keep track of the currently active link. It will be used
+ * in completion path to determine whether NCQ phase is in
+ * progress.
+ */
+ pp->active_link = qc->dev->link;
+
+ if (qc->tf.protocol == ATA_PROT_NCQ)
+ writel(1 << qc->tag, port_mmio + PORT_SCR_ACT);
+
+ if (pp->fbs_enabled && pp->fbs_last_dev != qc->dev->link->pmp) {
+ u32 fbs = readl(port_mmio + PORT_FBS);
+ fbs &= ~(PORT_FBS_DEV_MASK | PORT_FBS_DEC);
+ fbs |= qc->dev->link->pmp << PORT_FBS_DEV_OFFSET;
+ writel(fbs, port_mmio + PORT_FBS);
+ pp->fbs_last_dev = qc->dev->link->pmp;
+ }
+
+ writel(1 << qc->tag, port_mmio + PORT_CMD_ISSUE);
+
+ ahci_sw_activity(qc->dev->link);
+
+ /* For query ID command, restart the port if requred due to HW errata.
+ This is needed when PMP is attached. */
+ if (qc->dev->link->pmp && qc->tf.command == ATA_CMD_ID_ATA &&
+ readl(port_mmio + PORT_CMD_ISSUE) == 0x0) {
+ writel(PORT_CMD_FIS_RX, port_mmio + PORT_CMD);
+ readl(port_mmio + PORT_CMD); /* flush */
+ writel(PORT_CMD_FIS_RX | PORT_CMD_START, port_mmio + PORT_CMD);
+ readl(port_mmio + PORT_CMD); /* flush */
+ }
+
+ return 0;
+}
+
+static void xgene_ahci_enable_phy(struct xgene_ahci_context *ctx,
+ int channel, int enable)
+{
+ void *mmio = ctx->mmio_base;
+ u32 val;
+
+ xgene_ahci_in32(mmio + PORTCFG_ADDR, &val);
+ val = PORTADDR_SET(val, channel == 0 ? 2 : 3);
+ xgene_ahci_out32_flush(mmio + PORTCFG_ADDR, val);
+ xgene_ahci_in32(mmio + PORTPHY1CFG_ADDR, &val);
+ val = PORTPHY1CFG_FRCPHYRDY_SET(val, enable);
+ xgene_ahci_out32(mmio + PORTPHY1CFG_ADDR, val);
+}
+
+void xgene_ahci_set_phy_cfg(struct xgene_ahci_context *ctx, int channel)
+{
+ void *mmio = ctx->mmio_base;
+ u32 val;
+
+ dev_dbg(ctx->dev, "SATA%d.%d port configure mmio 0x%p channel %d\n",
+ ctx->cid, channel, mmio, channel);
+ xgene_ahci_in32(mmio + PORTCFG_ADDR, &val);
+ val = PORTADDR_SET(val, channel == 0 ? 2 : 3);
+ xgene_ahci_out32_flush(mmio + PORTCFG_ADDR, val);
+ /* Disable fix rate */
+ xgene_ahci_out32_flush(mmio + PORTPHY1CFG_ADDR, 0x0001fffe);
+ xgene_ahci_out32_flush(mmio + PORTPHY2CFG_ADDR, 0x5018461c);
+ xgene_ahci_out32_flush(mmio + PORTPHY3CFG_ADDR, 0x1c081907);
+ xgene_ahci_out32_flush(mmio + PORTPHY4CFG_ADDR, 0x1c080815);
+ xgene_ahci_in32(mmio + PORTPHY5CFG_ADDR, &val);
+ /* Window negotiation 0x800 to 0x400 */
+ val = PORTPHY5CFG_RTCHG_SET(val, 0x300);
+ xgene_ahci_out32(mmio + PORTPHY5CFG_ADDR, val);
+ xgene_ahci_in32(mmio + PORTAXICFG_ADDR, &val);
+ val = PORTAXICFG_EN_CONTEXT_SET(val, 0x1); /* enable context mgmt */
+ val = PORTAXICFG_OUTTRANS_SET(val, 0xe); /* Outstanding */
+ xgene_ahci_out32_flush(mmio + PORTAXICFG_ADDR, val);
+}
+
+/* Restart the PHY in case of disparity error for Gen2/Gen1 disk only */
+static int xgene_ahci_phy_restart(struct ata_link *link)
+{
+ struct ata_port *port = link->ap;
+ struct ata_host *host = port->host;
+ struct xgene_ahci_context *ctx = host->private_data;
+ int channel;
+
+ channel = xgene_ahci_get_channel(host, port);
+ if (channel < 0 || channel >= MAX_AHCI_CHN_PERCTR)
+ return -EINVAL;
+ xgene_ahci_enable_phy(ctx, channel, 1);
+ xgene_ahci_enable_phy(ctx, channel, 0);
+ xgene_ahci_delayms(50); /* Allow serdes to get reflected */
+ return 0;
+}
+
+static int xgene_ahci_hardreset(struct ata_link *link, unsigned int *class,
+ unsigned long deadline)
+{
+ const unsigned long *timing = sata_ehc_deb_timing(&link->eh_context);
+ struct ata_port *ap = link->ap;
+ struct ahci_port_priv *pp = ap->private_data;
+ u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG;
+ struct ata_taskfile tf;
+ bool online;
+ int rc;
+ struct ata_host *host = ap->host;
+ struct xgene_ahci_context *ctx = host->private_data;
+ int retry = 0;
+ u32 sstatus;
+ int channel;
+ int link_retry = 0;
+ void __iomem *port_mmio;
+ int portcmd_saved;
+ u32 portclb_saved;
+ u32 portclbhi_saved;
+ u32 portrxfis_saved;
+ u32 portrxfishi_saved;
+ u32 val;
+
+ channel = xgene_ahci_get_channel(host, ap);
+ if (channel >= MAX_AHCI_CHN_PERCTR) {
+ *class = ATA_DEV_NONE;
+ return 0;
+ }
+ ata_link_dbg(link, "SATA%d.%d APM hardreset\n", ctx->cid, channel);
+
+ /* As hardreset reset these CSR, let save it to restore later */
+ port_mmio = ahci_port_base(ap);
+ portcmd_saved = readl(port_mmio + PORT_CMD);
+ portclb_saved = readl(port_mmio + PORT_LST_ADDR);
+ portclbhi_saved = readl(port_mmio + PORT_LST_ADDR_HI);
+ portrxfis_saved = readl(port_mmio + PORT_FIS_ADDR);
+ portrxfishi_saved = readl(port_mmio + PORT_FIS_ADDR_HI);
+ ata_link_dbg(link, "SATA%d.%d PORT_CMD 0x%08X\n", ctx->cid, channel,
+ portcmd_saved);
+
+ ahci_stop_engine(ap);
+
+hardreset_retry:
+ /* clear D2H reception area to properly wait for D2H FIS */
+ ata_tf_init(link->device, &tf);
+ tf.command = 0x80;
+ ata_tf_to_fis(&tf, 0, 0, d2h_fis);
+ if (!xgene_ahci_is_A1())
+ xgene_ahci_serdes_set_pq(ctx, channel, 1);
+ rc = sata_link_hardreset(link, timing, deadline, &online,
+ ahci_check_ready);
+ if (!xgene_ahci_is_A1())
+ xgene_ahci_serdes_set_pq(ctx, channel, 0);
+ /* clear all errors */
+ xgene_ahci_in32(port_mmio + PORT_SCR_ERR, &val);
+ xgene_ahci_out32(port_mmio + PORT_SCR_ERR, val);
+
+ /* Check to ensure that the disk comes up in match speed */
+ if (online) {
+ sata_scr_read(link, SCR_STATUS, &sstatus);
+ if (!retry) {
+ if (((sstatus >> 4) & 0xf) == 2) {
+ /* For Gen2 and first time, let's check again
+ * with Gen2 serdes to ensure actual Gen2 disk.
+ */
+ xgene_ahci_serdes_force_gen(ctx, channel,
+ SPD_SEL_GEN2);
+ xgene_ahci_phy_restart(link);
+ ++retry;
+ goto hardreset_retry;
+ } else if (((sstatus >> 4) & 0xf) == 1) {
+ /* For Gen1 and first time, let's check again
+ * with Gen1 serdes to ensure actual Gen1 disk.
+ */
+ xgene_ahci_serdes_force_gen(ctx, channel,
+ SPD_SEL_GEN1);
+ xgene_ahci_phy_restart(link);
+ ++retry;
+ goto hardreset_retry;
+ }
+ }
+ } else if (link_retry < 4) {
+ link_retry++;
+ goto hardreset_retry;
+ }
+ ata_link_dbg(link, "SATA%d.%d post-hardrest PORT_CMD 0x%08X\n",
+ ctx->cid, channel, readl(port_mmio + PORT_CMD));
+
+ /* As controller hardreset clear them, let restore them */
+ writel(portcmd_saved, port_mmio + PORT_CMD);
+ writel(portclb_saved, port_mmio + PORT_LST_ADDR);
+ writel(portclbhi_saved, port_mmio + PORT_LST_ADDR_HI);
+ writel(portrxfis_saved, port_mmio + PORT_FIS_ADDR);
+ writel(portrxfishi_saved, port_mmio + PORT_FIS_ADDR_HI);
+ ata_link_dbg(link, "SATA%d.%d restore PORT_CMD 0x%08X\n",
+ ctx->cid, channel, readl(port_mmio + PORT_CMD));
+
+ ahci_start_engine(ap);
+
+ if (online)
+ *class = ahci_dev_classify(ap);
+
+ ata_link_dbg(link, "SATA%d.%d APM hardreset EXIT rc %d class %u\n",
+ ctx->cid, channel, rc, *class);
+ return rc;
+}
+
+static const char *xgene_ahci_chip_revision(void)
+{
+ static const char *revision = NULL;
+
+ if (!revision) {
+ #define EFUSE0_SHADOW_VERSION_SHIFT 28
+ #define EFUSE0_SHADOW_VERSION_MASK 0xF
+ void *efuse;
+ void *jtag;
+ u32 efuse0;
+ u32 jtagid;
+
+ /* Part registers are fixed in X-Gene. */
+#if defined(CONFIG_ARCH_MSLIM)
+ /* MSLIM address map uses 0xC000.0000 */
+ efuse = ioremap(0xC054A000ULL, 0x100);
+#else
+ /* Potenza address map uses 0x1000.0000 */
+ efuse = ioremap(0x1054A000ULL, 0x100);
+#endif
+ jtag = ioremap(0x17000004ULL, 0x100);
+ if (efuse == NULL || jtag == NULL) {
+ if (efuse)
+ iounmap(efuse);
+ if (jtag)
+ iounmap(jtag);
+ return revision = "A1";
+ }
+ efuse0 = (readl(efuse) >> EFUSE0_SHADOW_VERSION_SHIFT)
+ & EFUSE0_SHADOW_VERSION_MASK;
+ iounmap(efuse);
+ jtagid = readl(jtag);
+ iounmap(jtag);
+ switch (efuse0) {
+ case 0x00:
+ if (jtagid & 0x10000000)
+ return revision = "A2";
+ else
+ return revision = "A1";
+ case 0x01: /* A2 */
+ return revision = "A2";
+ case 0x02: /* A3 */
+ return revision = "A3";
+ case 0x03: /* B0 */
+ return revision = "B0";
+ default: /* Unknown */
+ return revision = "Unknown";
+ }
+ }
+ return revision;
+}
+
+int xgene_ahci_is_A1(void)
+{
+ return strcmp(xgene_ahci_chip_revision(), "A1") == 0 ? 1 : 0;
+}
+
+/* Flush the IOB to ensure all SATA controller writes completed before
+ servicing the completed command. */
+static int xgene_ahci_iob_flush(struct xgene_ahci_context *ctx)
+{
+ if (ctx->ahbc_io_base == NULL) {
+ void *ahbc_base;
+ u32 val;
+
+ /* The AHBC address is fixed in X-Gene */
+ ahbc_base = devm_ioremap(ctx->dev, 0x1F2A0000, 0x80000);
+ if (!ahbc_base) {
+ dev_err(ctx->dev, "can't map AHBC resource\n");
+ return -ENODEV;
+ }
+ /* The read to flush addres is fixed in X-Gene */
+ ctx->ahbc_io_base = devm_ioremap(ctx->dev, 0x1C000200, 0x100);
+ if (!ctx->ahbc_io_base) {
+ devm_iounmap(ctx->dev, ahbc_base);
+ dev_err(ctx->dev, "can't map AHBC IO resource\n");
+ return -ENODEV;
+ }
+ /* Enable IOB flush feature */
+ val = readl(ahbc_base + CFG_AMA_MODE_ADDR);
+ val |= CFG_RD2WR_EN;
+ writel(val, ahbc_base + CFG_AMA_MODE_ADDR);
+ devm_iounmap(ctx->dev, ahbc_base);
+ }
+ readl(ctx->ahbc_io_base);
+ return 0;
+}
+
+static unsigned int xgene_ahci_fill_sg(struct ata_queued_cmd *qc,
+ void *cmd_tbl)
+{
+ struct scatterlist *sg;
+ struct ahci_sg *ahci_sg = cmd_tbl + AHCI_CMD_TBL_HDR_SZ;
+ unsigned int si;
+
+ /*
+ * Next, the S/G list.
+ */
+ for_each_sg(qc->sg, sg, qc->n_elem, si) {
+ dma_addr_t addr = sg_dma_address(sg);
+ u64 dma_addr = xgene_ahci_to_axi(addr);
+ u32 sg_len = sg_dma_len(sg);
+ ahci_sg[si].addr = cpu_to_le32(dma_addr & 0xffffffff);
+ ahci_sg[si].addr_hi = cpu_to_le32((dma_addr >> 16) >> 16);
+ ahci_sg[si].flags_size = cpu_to_le32(sg_len - 1);
+ xgene_ahci_dflush((void *) __va(addr), sg_len);
+ }
+ return si;
+}
+
+static void xgene_ahci_qc_prep(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ struct ahci_port_priv *pp = ap->private_data;
+ int is_atapi = ata_is_atapi(qc->tf.protocol);
+ void *cmd_tbl;
+ u32 opts;
+ const u32 cmd_fis_len = 5; /* five dwords */
+ unsigned int n_elem;
+ void *port_mmio = ahci_port_base(ap);
+ u32 fbs;
+
+ /*
+ * Fill in command table information. First, the header,
+ * a SATA Register - Host to Device command FIS.
+ */
+ cmd_tbl = pp->cmd_tbl + qc->tag * AHCI_CMD_TBL_SZ;
+
+ /* Due to hardware errata for port multipier CBS mode, enable DEV
+ field of PxFBS in order to clear the PxCI */
+ if (qc->dev->link->pmp) {
+ fbs = readl(port_mmio + 0x40);
+ if ((fbs >> 8) & 0x0000000f) {
+ fbs &= 0xfffff0ff;
+ fbs |= qc->dev->link->pmp << 8;
+ writel(fbs, port_mmio + 0x40);
+ }
+ }
+
+ ata_tf_to_fis(&qc->tf, qc->dev->link->pmp, 1, cmd_tbl);
+ if (is_atapi) {
+ memset(cmd_tbl + AHCI_CMD_TBL_CDB, 0, 32);
+ memcpy(cmd_tbl + AHCI_CMD_TBL_CDB, qc->cdb, qc->dev->cdb_len);
+ }
+ n_elem = 0;
+ if (qc->flags & ATA_QCFLAG_DMAMAP)
+ n_elem = xgene_ahci_fill_sg(qc, cmd_tbl);
+
+ /*
+ * Fill in command slot information.
+ */
+ opts = cmd_fis_len | n_elem << 16 | (qc->dev->link->pmp << 12);
+ if (qc->tf.flags & ATA_TFLAG_WRITE)
+ opts |= AHCI_CMD_WRITE;
+ if (is_atapi)
+ opts |= AHCI_CMD_ATAPI | AHCI_CMD_PREFETCH;
+
+ xgene_ahci_fill_cmd_slot(pp, qc->tag, opts);
+}
+
+/* Due to HW BUG we are limited to single FIS receive area for FBS
+ * so limiting the FBS FIS area from 16 to 0
+ */
+static bool xgene_ahci_qc_fill_rtf(struct ata_queued_cmd *qc)
+{
+ struct ahci_port_priv *pp = qc->ap->private_data;
+ u8 *rx_fis = pp->rx_fis;
+
+ /*
+ * After a successful execution of an ATA PIO data-in command,
+ * the device doesn't send D2H Reg FIS to update the TF and
+ * the host should take TF and E_Status from the preceding PIO
+ * Setup FIS.
+ */
+ if (qc->tf.protocol == ATA_PROT_PIO && qc->dma_dir == DMA_FROM_DEVICE &&
+ !(qc->flags & ATA_QCFLAG_FAILED)) {
+ ata_tf_from_fis(rx_fis + RX_FIS_PIO_SETUP, &qc->result_tf);
+ qc->result_tf.command = (rx_fis + RX_FIS_PIO_SETUP)[15];
+ } else
+ ata_tf_from_fis(rx_fis + RX_FIS_D2H_REG, &qc->result_tf);
+
+ return true;
+}
+
+static int xgene_ahci_do_softreset(struct ata_link *link,
+ unsigned int *class, int pmp, unsigned long deadline,
+ int (*check_ready)(struct ata_link *link))
+{
+ struct ata_port *ap = link->ap;
+ struct ahci_host_priv *hpriv = ap->host->private_data;
+ const char *reason = NULL;
+ unsigned long now, msecs;
+ struct ata_taskfile tf;
+ int rc;
+
+ ata_link_dbg(link, "ENTER\n");
+
+ /* prepare for SRST (AHCI-1.1 10.4.1) */
+ rc = ahci_kick_engine(ap);
+ if (rc && rc != -EOPNOTSUPP)
+ ata_link_warn(link, "failed to reset engine (errno=%d)\n", rc);
+
+ ata_tf_init(link->device, &tf);
+ /* issue the first D2H Register FIS */
+ msecs = 0;
+ now = jiffies;
+ if (time_after(deadline, now))
+ msecs = jiffies_to_msecs(deadline - now);
+
+ tf.ctl |= ATA_SRST;
+ /* Must call X-Gene version in case it needs to flush the cache for
+ MSLIM as well as AXI address translation */
+ if (xgene_ahci_exec_polled_cmd(ap, pmp, &tf, 0,
+ AHCI_CMD_RESET | AHCI_CMD_CLR_BUSY, msecs)) {
+ rc = -EIO;
+ reason = "1st FIS failed";
+ goto fail;
+ }
+
+ /* spec says at least 5us, but be generous and sleep for 1ms */
+ ata_msleep(ap, 1);
+
+ /* issue the second D2H Register FIS */
+ tf.ctl &= ~ATA_SRST;
+ /* HW need AHCI_CMD_RESET and AHCI_CMD_CLR_BUSY */
+ xgene_ahci_exec_polled_cmd(ap, pmp, &tf, 0,
+ AHCI_CMD_RESET | AHCI_CMD_CLR_BUSY, msecs);
+ /* wait for link to become ready */
+ rc = ata_wait_after_reset(link, deadline, check_ready);
+ if (rc == -EBUSY && hpriv->flags & AHCI_HFLAG_SRST_TOUT_IS_OFFLINE) {
+ /*
+ * Workaround for cases where link online status can't
+ * be trusted. Treat device readiness timeout as link
+ * offline.
+ */
+ ata_link_info(link, "device not ready, treating as offline\n");
+ *class = ATA_DEV_NONE;
+ } else if (rc) {
+ /* link occupied, -ENODEV too is an error */
+ reason = "device not ready";
+ goto fail;
+ } else {
+ *class = ahci_dev_classify(ap);
+ }
+
+ ata_link_dbg(link, "EXIT, class=%u\n", *class);
+ return 0;
+
+ fail:
+ ata_link_err(link, "softreset failed (%s)\n", reason);
+ return rc;
+}
+
+static int xgene_ahci_softreset(struct ata_link *link, unsigned int *class,
+ unsigned long deadline)
+{
+ int pmp = sata_srst_pmp(link);
+ return xgene_ahci_do_softreset(link, class, pmp, deadline,
+ ahci_check_ready);
+}
+
+static struct ata_port_operations xgene_ahci_ops = {
+ .inherits = &ahci_ops,
+ .hardreset = xgene_ahci_hardreset,
+ .read_id = xgene_ahci_read_id,
+ .qc_prep = xgene_ahci_qc_prep,
+ .qc_issue = xgene_ahci_qc_issue,
+#if defined(CONFIG_ARCH_MSLIM)
+ .port_resume = xgene_ahci_port_resume,
+ .port_start = xgene_ahci_port_start,
+#endif
+ .softreset = xgene_ahci_softreset,
+ .pmp_softreset = xgene_ahci_softreset,
+ .qc_fill_rtf = xgene_ahci_qc_fill_rtf,
+};
+
+static const struct ata_port_info xgene_ahci_port_info[] = {
+ {
+ .flags = AHCI_FLAG_COMMON,
+ .pio_mask = ATA_PIO4,
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &xgene_ahci_ops,
+ },
+};
+
+static struct scsi_host_template xgene_ahci_sht = {
+ AHCI_SHT("XGene-ahci"),
+};
+
+static void xgene_ahci_port_intr(struct ata_port *ap)
+{
+ void __iomem *port_mmio = ahci_port_base(ap);
+ struct ata_eh_info *ehi = &ap->link.eh_info;
+ struct ahci_port_priv *pp = ap->private_data;
+ struct ahci_host_priv *hpriv = ap->host->private_data;
+ int resetting = !!(ap->pflags & ATA_PFLAG_RESETTING);
+ u32 status, qc_active = 0;
+ int rc;
+
+ status = readl(port_mmio + PORT_IRQ_STAT);
+ writel(status, port_mmio + PORT_IRQ_STAT);
+
+ /* ignore BAD_PMP while resetting */
+ if (unlikely(resetting))
+ status &= ~PORT_IRQ_BAD_PMP;
+
+ /* if LPM is enabled, PHYRDY doesn't mean anything */
+ if (ap->link.lpm_policy > ATA_LPM_MAX_POWER) {
+ status &= ~PORT_IRQ_PHYRDY;
+ ahci_scr_write(&ap->link, SCR_ERROR, SERR_PHYRDY_CHG);
+ }
+
+ if (unlikely(status & PORT_IRQ_ERROR)) {
+ ahci_error_intr(ap, status);
+ return;
+ }
+
+ if (status & PORT_IRQ_SDB_FIS) {
+ /* If SNotification is available, leave notification
+ * handling to sata_async_notification(). If not,
+ * emulate it by snooping SDB FIS RX area.
+ *
+ * Snooping FIS RX area is probably cheaper than
+ * poking SNotification but some constrollers which
+ * implement SNotification, ICH9 for example, don't
+ * store AN SDB FIS into receive area.
+ */
+ if (hpriv->cap & HOST_CAP_SNTF)
+ sata_async_notification(ap);
+ else {
+ /* If the 'N' bit in word 0 of the FIS is set,
+ * we just received asynchronous notification.
+ * Tell libata about it.
+ *
+ * Lack of SNotification should not appear in
+ * ahci 1.2, so the workaround is unnecessary
+ * when FBS is enabled.
+ */
+ if (pp->fbs_enabled)
+ WARN_ON_ONCE(1);
+ else {
+ const __le32 *f = pp->rx_fis + RX_FIS_SDB;
+ u32 f0 = le32_to_cpu(f[0]);
+ if (f0 & (1 << 15))
+ sata_async_notification(ap);
+ }
+ }
+ }
+
+ /* pp->active_link is not reliable once FBS is enabled, both
+ * PORT_SCR_ACT and PORT_CMD_ISSUE should be checked because
+ * NCQ and non-NCQ commands may be in flight at the same time.
+ */
+ if (pp->fbs_enabled) {
+ if (ap->qc_active) {
+ qc_active = readl(port_mmio + PORT_SCR_ACT);
+ qc_active |= readl(port_mmio + PORT_CMD_ISSUE);
+ }
+ } else {
+ /* pp->active_link is valid iff any command is in flight */
+ if (ap->qc_active && pp->active_link->sactive)
+ qc_active = readl(port_mmio + PORT_SCR_ACT);
+ else
+ qc_active = readl(port_mmio + PORT_CMD_ISSUE);
+ }
+
+ /* Flush the IOB before servicing interrupt to ensure all data
+ written by the controller appears in DDR */
+ xgene_ahci_iob_flush((struct xgene_ahci_context *) hpriv);
+
+ rc = ata_qc_complete_multiple(ap, qc_active);
+
+ /* while resetting, invalid completions are expected */
+ if (unlikely(rc < 0 && !resetting)) {
+ ehi->err_mask |= AC_ERR_HSM;
+ ehi->action |= ATA_EH_RESET;
+ ata_port_freeze(ap);
+ }
+}
+
+static irqreturn_t xgene_ahci_interrupt(int irq, void *dev_instance)
+{
+ struct ata_host *host = dev_instance;
+ struct ahci_host_priv *hpriv;
+ unsigned int i, handled = 0;
+ void __iomem *mmio;
+ u32 irq_stat, irq_masked;
+
+ VPRINTK("ENTER\n");
+
+ hpriv = host->private_data;
+ mmio = hpriv->mmio;
+
+ /* sigh. 0xffffffff is a valid return from h/w */
+ irq_stat = readl(mmio + HOST_IRQ_STAT);
+ if (!irq_stat)
+ return IRQ_NONE;
+
+ irq_masked = irq_stat & hpriv->port_map;
+
+ spin_lock(&host->lock);
+
+ for (i = 0; i < host->n_ports; i++) {
+ struct ata_port *ap;
+
+ if (!(irq_masked & (1 << i)))
+ continue;
+
+ ap = host->ports[i];
+ if (ap) {
+ xgene_ahci_port_intr(ap);
+ VPRINTK("port %u\n", i);
+ } else {
+ VPRINTK("port %u (no irq)\n", i);
+ if (ata_ratelimit())
+ dev_warn(host->dev,
+ "interrupt on disabled port %u\n", i);
+ }
+
+ handled = 1;
+ }
+
+ /* HOST_IRQ_STAT behaves as level triggered latch meaning that
+ * it should be cleared after all the port events are cleared;
+ * otherwise, it will raise a spurious interrupt after each
+ * valid one. Please read section 10.6.2 of ahci 1.1 for more
+ * information.
+ *
+ * Also, use the unmasked value to clear interrupt as spurious
+ * pending event on a dummy port might cause screaming IRQ.
+ */
+ writel(irq_stat, mmio + HOST_IRQ_STAT);
+
+ spin_unlock(&host->lock);
+
+ VPRINTK("EXIT\n");
+
+ return IRQ_RETVAL(handled);
+}
+
+static int xgene_ahci_get_irq(struct platform_device *pdev, int index)
+{
+ if (efi_enabled(EFI_BOOT))
+ return platform_get_irq(pdev, index);
+ return irq_of_parse_and_map(pdev->dev.of_node, index);
+}
+
+static int xgene_ahci_get_resource(struct platform_device *pdev, int index,
+ struct resource *res)
+{
+ struct resource *regs;
+ if (efi_enabled(EFI_BOOT)) {
+ regs = platform_get_resource(pdev, IORESOURCE_MEM, index);
+ if (regs == NULL)
+ return -ENODEV;
+ *res = *regs;
+ return 0;
+ }
+ return of_address_to_resource(pdev->dev.of_node, index, res);
+}
+
+static int xgene_ahci_get_u32_param(struct platform_device *pdev,
+ const char *of_name, char *acpi_name, u32 *param)
+{
+#ifdef CONFIG_ACPI
+ if (efi_enabled(EFI_BOOT)) {
+ unsigned long long value;
+ acpi_status status;
+ if (acpi_name == NULL)
+ return -ENODEV;
+ status = acpi_evaluate_integer(ACPI_HANDLE(&pdev->dev),
+ acpi_name, NULL, &value);
+ if (ACPI_FAILURE(status))
+ return -ENODEV;
+ *param = value;
+ return 0;
+ }
+#endif
+ if (of_name == NULL)
+ return -ENODEV;
+ return of_property_read_u32(pdev->dev.of_node, of_name, param);
+}
+
+static int xgene_ahci_get_str_param(struct platform_device *pdev,
+ const char *of_name, char *acpi_name, char *buf, int len)
+{
+ int rc;
+ const char *param;
+#ifdef CONFIG_ACPI
+ if (efi_enabled(EFI_BOOT)) {
+ acpi_status status;
+ struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
+ union acpi_object *acpi_obj;
+
+ if (acpi_name == NULL)
+ return -ENODEV;
+ status = acpi_evaluate_object(ACPI_HANDLE(&pdev->dev),
+ acpi_name, NULL, &buffer);
+ if (ACPI_FAILURE(status))
+ return -ENODEV;
+ acpi_obj = buffer.pointer;
+ if (acpi_obj->type != ACPI_TYPE_STRING) {
+ buf[0] = '\0';
+ kfree(buffer.pointer);
+ return -ENODEV;
+ }
+ if (acpi_obj->string.length < len) {
+ strncpy(buf, acpi_obj->string.pointer,
+ acpi_obj->string.length);
+ buf[acpi_obj->string.length] = '\0';
+ } else {
+ strncpy(buf, acpi_obj->string.pointer, len);
+ buf[len-1] = '\0';
+ }
+ kfree(buffer.pointer);
+ return 0;
+ }
+#endif
+ if (of_name == NULL)
+ return -ENODEV;
+ rc = of_property_read_string(pdev->dev.of_node, of_name, ¶m);
+ if (rc == 0) {
+ strncpy(buf, param, len);
+ buf[len - 1] = '\0';
+ } else {
+ buf[0] = '\0';
+ }
+ return rc;
+}
+
+static int xgene_ahci_probe(struct platform_device *pdev)
+{
+ struct xgene_ahci_context *hpriv;
+ struct ata_port_info pi = xgene_ahci_port_info[0];
+ const struct ata_port_info *ppi[] = { &pi, NULL };
+ struct ata_host *host;
+ struct resource res;
+ char res_name[30];
+ int n_ports;
+ int rc;
+ int i;
+ u32 val;
+ u32 rxclk_inv;
+ u32 gen_sel;
+ u32 serdes_diff_clk;
+
+ /* When both ACPi and DTS are enabled, custom ACPI built-in ACPI
+ table, and booting via DTS, we need to skip the probe of the
+ built-in ACPI table probe. */
+ if (!efi_enabled(EFI_BOOT) && pdev->dev.of_node == NULL)
+ return -ENODEV;
+
+ /* Check if the entry is disabled for OF only */
+ if (!efi_enabled(EFI_BOOT) &&
+ !of_device_is_available(pdev->dev.of_node))
+ return -ENODEV;
+#if defined(CONFIG_ACPI)
+ if (efi_enabled(EFI_BOOT)) {
+ struct acpi_device *device;
+
+ if (acpi_bus_get_device(ACPI_HANDLE(&pdev->dev), &device))
+ return -ENODEV;
+
+ if (acpi_bus_get_status(device) || !device->status.present)
+ return -ENODEV;
+ }
+#endif
+
+ hpriv = devm_kzalloc(&pdev->dev, sizeof(*hpriv), GFP_KERNEL);
+ if (!hpriv) {
+ dev_err(&pdev->dev, "can't allocate host context\n");
+ return -ENOMEM;
+ }
+ hpriv->dev = &pdev->dev;
+
+ rc = xgene_ahci_get_resource(pdev, 0, &res);
+ if (rc != 0) {
+ dev_err(&pdev->dev, "no AHCI resource address\n");
+ goto error;
+ }
+ hpriv->mmio_phys = res.start;
+ hpriv->mmio_base = devm_ioremap(&pdev->dev, res.start,
+ resource_size(&res));
+ if (!hpriv->mmio_base) {
+ dev_err(&pdev->dev, "can't map MMIO resource\n");
+ rc = -ENOMEM;
+ goto error;
+ }
+ hpriv->hpriv.mmio = hpriv->mmio_base;
+
+ rc = xgene_ahci_get_resource(pdev, 1, &res);
+ if (rc != 0) {
+ dev_err(&pdev->dev, "no Serdes resource address\n");
+ goto error;
+ }
+ hpriv->csr_phys = res.start;
+ hpriv->csr_base = devm_ioremap(&pdev->dev, res.start,
+ resource_size(&res));
+ if (!hpriv->csr_base) {
+ dev_err(&pdev->dev, "can't map Serdes CSR resource\n");
+ rc = -ENOMEM;
+ goto error;
+ }
+
+ rc = xgene_ahci_get_str_param(pdev, "clock-names", "CLNM", res_name,
+ sizeof(res_name));
+ if (rc) {
+ dev_err(&pdev->dev, "no clock name resource\n");
+ goto error;
+ }
+ hpriv->hpriv.clk = clk_get(&pdev->dev, res_name);
+ if (!IS_ERR(hpriv->hpriv.clk)) {
+ rc = clk_prepare_enable(hpriv->hpriv.clk);
+ if (rc) {
+ dev_err(&pdev->dev, "clock prepare enable failed\n");
+ goto error;
+ }
+ } else {
+ dev_warn(&pdev->dev, "no clock\n");
+ }
+ if (strcmp(res_name, "eth01clk") == 0)
+ hpriv->cid = 0;
+ else if (strcmp(res_name, "eth23clk") == 0)
+ hpriv->cid = 1;
+ else
+ hpriv->cid = 2;
+
+ if (hpriv->cid == 2) {
+ rc = xgene_ahci_get_resource(pdev, 2, &res);
+ if (rc != 0) {
+ dev_err(&pdev->dev, "no SATA/PCIE resource address\n");
+ goto error;
+ }
+ hpriv->pcie_base = devm_ioremap(&pdev->dev, res.start,
+ resource_size(&res));
+ if (!hpriv->pcie_base) {
+ dev_err(&pdev->dev, "can't map SATA/PCIe resource\n");
+ rc = -ENOMEM;
+ goto error;
+ }
+ }
+
+ /* Map in the IOB register */
+ rc = xgene_ahci_iob_flush(hpriv);
+ if (rc)
+ goto error;
+
+ dev_dbg(&pdev->dev, "SATA%d PHY PAddr 0x%016LX VAddr 0x%p Mmio PAddr 0x%016LX VAddr 0x%p\n",
+ hpriv->cid, hpriv->csr_phys, hpriv->csr_base,
+ hpriv->mmio_phys, hpriv->mmio_base);
+
+ /* Custom Serdes override paraemter */
+ rc = xgene_ahci_get_u32_param(pdev, "gen-sel", "GENS", &gen_sel);
+ if (rc != 0)
+ gen_sel = 3; /* Default to Gen3 */
+ rc = xgene_ahci_get_u32_param(pdev, "serdes-diff-clk", "SDCL",
+ &serdes_diff_clk);
+ if (rc != 0)
+ serdes_diff_clk = SATA_CLK_EXT_DIFF; /* Default to external */
+ rc = xgene_ahci_get_u32_param(pdev, "EQA1", "EQA1", &hpriv->ctrl_eq_A1);
+ if (rc != 0)
+ hpriv->ctrl_eq_A1 = CTLE_EQ;
+ rc = xgene_ahci_get_u32_param(pdev, "EQ", "EQ00", &hpriv->ctrl_eq);
+ if (rc != 0)
+ hpriv->ctrl_eq = CTLE_EQ_A2;
+ dev_dbg(&pdev->dev, "SATA%d ctrl_eq %u %u\n", hpriv->cid,
+ hpriv->ctrl_eq_A1, hpriv->ctrl_eq);
+ rc = xgene_ahci_get_u32_param(pdev, "GENAVG", "GAVG",
+ &hpriv->use_gen_avg);
+ if (rc != 0)
+ hpriv->use_gen_avg = xgene_ahci_is_A1() ? 0 : 1;
+ dev_dbg(&pdev->dev, "SATA%d use avg %u\n", hpriv->cid,
+ hpriv->use_gen_avg);
+ rc = xgene_ahci_get_u32_param(pdev, "LBA1", "LBA1",
+ &hpriv->loopback_buf_en_A1);
+ if (rc != 0)
+ hpriv->loopback_buf_en_A1 = 1;
+ rc = xgene_ahci_get_u32_param(pdev, "LB", "LB00",
+ &hpriv->loopback_buf_en);
+ if (rc != 0)
+ hpriv->loopback_buf_en = 0;
+ dev_dbg(&pdev->dev, "SATA%d loopback_buf_en %u %u\n", hpriv->cid,
+ hpriv->loopback_buf_en_A1, hpriv->loopback_buf_en);
+ rc = xgene_ahci_get_u32_param(pdev, "LCA1", "LCA1",
+ &hpriv->loopback_ena_ctle_A1);
+ if (rc != 0)
+ hpriv->loopback_ena_ctle_A1 = 1;
+ rc = xgene_ahci_get_u32_param(pdev, "LC", "LC00",
+ &hpriv->loopback_ena_ctle);
+ if (rc != 0)
+ hpriv->loopback_ena_ctle = 0;
+ dev_dbg(&pdev->dev, "SATA%d loopback_ena_ctle %u %u\n", hpriv->cid,
+ hpriv->loopback_ena_ctle_A1, hpriv->loopback_ena_ctle);
+ rc = xgene_ahci_get_u32_param(pdev, "CDRA1", "CDR1",
+ &hpriv->spd_sel_cdr_A1);
+ if (rc != 0)
+ hpriv->spd_sel_cdr_A1 = SPD_SEL;
+ rc = xgene_ahci_get_u32_param(pdev, "CDR", "CDR0",
+ &hpriv->spd_sel_cdr);
+ if (rc != 0)
+ hpriv->spd_sel_cdr = SPD_SEL;
+ dev_dbg(&pdev->dev, "SATA%d spd_sel_cdr %u %u\n", hpriv->cid,
+ hpriv->spd_sel_cdr_A1, hpriv->spd_sel_cdr);
+ rc = xgene_ahci_get_u32_param(pdev, "PQA1", "PQA1", &hpriv->pq_A1);
+ if (rc != 0)
+ hpriv->pq_A1 = PQ_REG;
+ rc = xgene_ahci_get_u32_param(pdev, "PQ", "PQ00", &hpriv->pq);
+ if (rc != 0)
+ hpriv->pq = PQ_REG_A2;
+ hpriv->pq_sign = 0x1;
+ dev_dbg(&pdev->dev, "SATA%d pq %u %u %d\n", hpriv->cid, hpriv->pq_A1,
+ hpriv->pq, hpriv->pq_sign);
+ rc = xgene_ahci_get_u32_param(pdev, "coherent", "COHT",
+ &hpriv->coherent);
+ if (rc != 0)
+ hpriv->coherent = 1; /* Default to coherent IO */
+
+ hpriv->irq = xgene_ahci_get_irq(pdev, 0);
+ if (hpriv->irq <= 0) {
+ dev_err(&pdev->dev, "no IRQ resource\n");
+ rc = -ENODEV;
+ goto error;
+ }
+
+ rxclk_inv = xgene_ahci_is_A1() ? 1 : 0;
+ rc = xgene_ahci_serdes_init(hpriv, gen_sel, serdes_diff_clk, rxclk_inv);
+ if (rc != 0) {
+ dev_err(&pdev->dev, "SATA%d PHY initialize failed %d\n",
+ hpriv->cid, rc);
+ rc = -ENODEV;
+ goto error;
+ }
+
+ /* Remove IP RAM out of shutdown */
+ xgene_ahci_init_memram(hpriv);
+
+ if (hpriv->use_gen_avg) {
+ xgene_ahci_serdes_gen_avg_val(hpriv, 1);
+ xgene_ahci_serdes_gen_avg_val(hpriv, 0);
+ } else {
+ xgene_ahci_serdes_force_lat_summer_cal(hpriv, 0);
+ xgene_ahci_serdes_force_lat_summer_cal(hpriv, 1);
+ }
+ if (xgene_ahci_is_A1()) {
+ xgene_ahci_serdes_reset_rxa_rxd(hpriv, 0);
+ xgene_ahci_serdes_reset_rxa_rxd(hpriv, 1);
+ }
+ for (i = 0; i < MAX_AHCI_CHN_PERCTR; i++)
+ xgene_ahci_set_phy_cfg(hpriv, i);
+
+ /* Now enable top level interrupt. Otherwise, port interrupt will
+ not work. */
+ /* AXI disable Mask */
+ xgene_ahci_out32_flush(hpriv->mmio_base + HOST_IRQ_STAT, 0xffffffff);
+ xgene_ahci_out32(hpriv->csr_base + INTSTATUSMASK_ADDR, 0);
+ xgene_ahci_in32(hpriv->csr_base + INTSTATUSMASK_ADDR, &val);
+ dev_dbg(&pdev->dev,
+ "SATA%d top level interrupt mask 0x%X value 0x%08X\n",
+ hpriv->cid, INTSTATUSMASK_ADDR, val);
+ xgene_ahci_out32_flush(hpriv->csr_base + ERRINTSTATUSMASK_ADDR, 0x0);
+ xgene_ahci_out32_flush(hpriv->csr_base + SATA_SHIM_OFFSET +
+ INT_SLV_TMOMASK_ADDR, 0x0);
+ /* Enable AXI Interrupt */
+ xgene_ahci_out32(hpriv->csr_base + SLVRDERRATTRIBUTES_ADDR, 0xffffffff);
+ xgene_ahci_out32(hpriv->csr_base + SLVWRERRATTRIBUTES_ADDR, 0xffffffff);
+ xgene_ahci_out32(hpriv->csr_base + MSTRDERRATTRIBUTES_ADDR, 0xffffffff);
+ xgene_ahci_out32(hpriv->csr_base + MSTWRERRATTRIBUTES_ADDR, 0xffffffff);
+
+ /* Enable coherency unless explicit disabled */
+ if (hpriv->coherent) {
+ xgene_ahci_in32(hpriv->csr_base + BUSCTLREG_ADDR, &val);
+ val = MSTAWAUX_COHERENT_BYPASS_SET(val, 0);
+ val = MSTARAUX_COHERENT_BYPASS_SET(val, 0);
+ xgene_ahci_out32(hpriv->csr_base + BUSCTLREG_ADDR, val);
+
+ xgene_ahci_in32(hpriv->csr_base + IOFMSTRWAUX_ADDR, &val);
+ val |= (1 << 3); /* Enable read coherency */
+ val |= (1 << 9); /* Enable write coherency */
+ xgene_ahci_out32_flush(hpriv->csr_base + IOFMSTRWAUX_ADDR, val);
+ xgene_ahci_in32(hpriv->csr_base + IOFMSTRWAUX_ADDR, &val);
+ dev_dbg(&pdev->dev,
+ "SATA%d coherency 0x%X value 0x%08X\n",
+ hpriv->cid, IOFMSTRWAUX_ADDR, val);
+ }
+ /* Setup AHCI host priv structure */
+ ahci_save_initial_config(&pdev->dev, &hpriv->hpriv, 0, 0);
+
+ /* prepare host */
+ if (hpriv->hpriv.cap & HOST_CAP_NCQ)
+ pi.flags |= ATA_FLAG_NCQ;
+ if (hpriv->hpriv.cap & HOST_CAP_PMP) {
+ pi.flags |= ATA_FLAG_PMP;
+ if (hpriv->hpriv.cap & HOST_CAP_FBS)
+ hpriv->hpriv.flags |= AHCI_HFLAG_YES_FBS;
+ }
+ ahci_set_em_messages(&hpriv->hpriv, &pi);
+
+ /* CAP.NP sometimes indicate the index of the last enabled
+ * port, at other times, that of the last possible port, so
+ * determining the maximum port number requires looking at
+ * both CAP.NP and port_map.
+ */
+ n_ports = max(ahci_nr_ports(hpriv->hpriv.cap),
+ fls(hpriv->hpriv.port_map));
+
+ host = ata_host_alloc_pinfo(&pdev->dev, ppi, n_ports);
+ if (!host) {
+ dev_err(&pdev->dev, "can not allocate host pinfo\n");
+ rc = -ENOMEM;
+ goto error;
+ }
+
+ host->private_data = hpriv;
+
+ if (!(hpriv->hpriv.cap & HOST_CAP_SSS) || ahci_ignore_sss)
+ host->flags |= ATA_HOST_PARALLEL_SCAN;
+ else
+ dev_warn(&pdev->dev,
+ "ahci: SSS flag set, parallel bus scan disabled\n");
+
+ if (pi.flags & ATA_FLAG_EM)
+ ahci_reset_em(host);
+
+ for (i = 0; i < host->n_ports; i++) {
+ struct ata_port *ap = host->ports[i];
+
+ ata_port_desc(ap, "mmio 0x%llX", hpriv->mmio_phys);
+ ata_port_desc(ap, "port 0x%x", 0x100 + ap->port_no * 0x80);
+
+ /* set enclosure management message type */
+ if (ap->flags & ATA_FLAG_EM)
+ ap->em_message_type = hpriv->hpriv.em_msg_type;
+
+ /* disabled/not-implemented port */
+ if (!(hpriv->hpriv.port_map & (1 << i)))
+ ap->ops = &ata_dummy_port_ops;
+ }
+
+ rc = ahci_reset_controller(host);
+ if (rc)
+ goto error;
+
+ ahci_init_controller(host);
+ ahci_print_info(host, "XGene-AHCI\n");
+
+ if (xgene_ahci_is_A1()) {
+ xgene_ahci_sht.can_queue = 1;
+ dev_warn(&pdev->dev, "SATA%d limited to 1 NCQ\n", hpriv->cid);
+ }
+
+ /* Setup DMA mask */
+ pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
+ pdev->dev.coherent_dma_mask = DMA_BIT_MASK(64);
+
+ rc = ata_host_activate(host, hpriv->irq, xgene_ahci_interrupt,
+ IRQF_SHARED, &xgene_ahci_sht);
+ if (rc)
+ goto error;
+
+ dev_dbg(&pdev->dev, "SATA%d PHY initialized\n", hpriv->cid);
+ return 0;
+
+error:
+ devm_kfree(&pdev->dev, hpriv);
+ return rc;
+}
+
+static int xgene_ahci_remove(struct platform_device *pdev)
+{
+ struct ata_host *host = dev_get_drvdata(&pdev->dev);
+ struct xgene_ahci_context *hpriv = host->private_data;
+
+ dev_dbg(&pdev->dev, "SATA%d remove\n", hpriv->cid);
+ devm_kfree(&pdev->dev, hpriv);
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int xgene_ahci_suspend(struct platform_device *pdev, pm_message_t state)
+{
+ struct ata_host *host = dev_get_drvdata(&pdev->dev);
+ struct xgene_ahci_context *hpriv = host->private_data;
+ void __iomem *mmio = hpriv->mmio_base;
+ u32 ctl;
+ int rc;
+
+ dev_dbg(&pdev->dev, "SATA%d suspend\n", hpriv->cid);
+
+ /*
+ * AHCI spec rev1.1 section 8.3.3:
+ * Software must disable interrupts prior to requesting a
+ * transition of the HBA to D3 state.
+ */
+ ctl = readl(mmio + HOST_CTL);
+ ctl &= ~HOST_IRQ_EN;
+ writel(ctl, mmio + HOST_CTL);
+ readl(mmio + HOST_CTL); /* flush */
+
+ rc = ata_host_suspend(host, state);
+ if (rc)
+ return rc;
+
+ if (!IS_ERR(hpriv->hpriv.clk))
+ clk_disable_unprepare(hpriv->hpriv.clk);
+ return 0;
+}
+
+static int xgene_ahci_resume(struct platform_device *pdev)
+{
+ struct ata_host *host = dev_get_drvdata(&pdev->dev);
+ struct xgene_ahci_context *hpriv = host->private_data;
+ int rc;
+
+ dev_dbg(&pdev->dev, "SATA%d resume\n", hpriv->cid);
+
+ if (!IS_ERR(hpriv->hpriv.clk)) {
+ rc = clk_prepare_enable(hpriv->hpriv.clk);
+ if (rc) {
+ dev_err(&pdev->dev, "clock prepare enable failed\n");
+ return rc;
+ }
+ }
+
+ if (pdev->dev.power.power_state.event == PM_EVENT_SUSPEND) {
+ rc = ahci_reset_controller(host);
+ if (rc)
+ goto disable_unprepare_clk;
+
+ ahci_init_controller(host);
+ }
+
+ ata_host_resume(host);
+ return 0;
+
+disable_unprepare_clk:
+ if (!IS_ERR(hpriv->hpriv.clk))
+ clk_disable_unprepare(hpriv->hpriv.clk);
+
+ return rc;
+}
+#endif
+
+static const struct acpi_device_id xgene_ahci_acpi_match[] = {
+ { "APMC0D00", 0 },
+ {},
+};
+MODULE_DEVICE_TABLE(acpi, xgene_ahci_acpi_match);
+
+static const struct of_device_id xgene_ahci_of_match[] = {
+ { .compatible = "apm,xgene-ahci", },
+ {},
+};
+MODULE_DEVICE_TABLE(of, xgene_ahci_of_match);
+
+static struct platform_driver xgene_ahci_driver = {
+ .driver = {
+ .name = "xgene-ahci",
+ .owner = THIS_MODULE,
+ .of_match_table = xgene_ahci_of_match,
+ .acpi_match_table = ACPI_PTR(xgene_ahci_acpi_match),
+ },
+ .probe = xgene_ahci_probe,
+ .remove = xgene_ahci_remove,
+#ifdef CONFIG_PM
+ .suspend = xgene_ahci_suspend,
+ .resume = xgene_ahci_resume,
+#endif
+};
+module_platform_driver(xgene_ahci_driver);
+
+MODULE_DESCRIPTION("APM X-Gene AHCI SATA driver");
+MODULE_AUTHOR("Loc Ho <lho@apm.com>");
+MODULE_LICENSE("GPL");
+MODULE_VERSION("0.3");
new file mode 100644
@@ -0,0 +1,112 @@
+/*
+ * AppliedMicro X-Gene SATA PHY driver
+ *
+ * Copyright (c) 2013, Applied Micro Circuits Corporation
+ * Author: Loc Ho <lho@apm.com>
+ * Tuan Phan <tphan@apm.com>
+ * Suman Tripathi <stripathi@apm.com>
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+#ifndef __SATA_XGENE_H__
+#define __SATA_XGENE_H__
+
+#include "ahci.h" /* for ahci_host_priv */
+
+/* Default tuning parameters */
+#define XGENE_SERDES_VAL_NOT_SET ~0x0
+#define CTLE_EQ 0x9
+#define PQ_REG 0x8
+#define CTLE_EQ_A2 0x2
+#define PQ_REG_A2 0xa
+#define SPD_SEL 0x5
+
+/*
+ * Configure Reference clock (clock type):
+ * External differential 0
+ * Internal differential 1
+ * Internal single ended 2
+ */
+#define SATA_CLK_EXT_DIFF 0
+#define SATA_CLK_INT_DIFF 1
+#define SATA_CLK_INT_SING 2
+
+#define SPD_SEL_GEN2 0x3
+#define SPD_SEL_GEN1 0x1
+
+struct xgene_ahci_context {
+ struct ahci_host_priv hpriv;
+ struct device *dev;
+ u8 cid; /* Controller ID */
+ int irq; /* IRQ */
+ void *csr_base; /* CSR base address of IP - serdes */
+ void *mmio_base; /* AHCI I/O base address */
+ void *pcie_base; /* Shared Serdes CSR in PCIe 4/5 domain */
+ void *ahbc_io_base; /* Used for IOB flushing */
+ u64 csr_phys; /* Physical address of CSR base address */
+ u64 mmio_phys; /* Physical address of MMIO base address */
+
+ /* Override Serdes parameters */
+ u32 ctrl_eq_A1; /* Serdes Reg 1 RX/TX ctrl_eq value for A1 */
+ u32 ctrl_eq; /* Serdes Reg 1 RX/TX ctrl_eq value */
+ u32 pq_A1; /* Serdes Reg 125 pq value for A1 */
+ u32 pq; /* Serdes Reg 125 pq value */
+ u32 pq_sign; /* Serdes Reg 125 pq sign */
+ u32 loopback_buf_en_A1; /* Serdes Reg 4 Tx loopback buf enable for A1 */
+ u32 loopback_buf_en; /* Serdes Reg 4 Tx loopback buf enable */
+ u32 loopback_ena_ctle_A1; /* Serdes Reg 7 loopback enable ctrl for A1 */
+ u32 loopback_ena_ctle; /* Serdes Reg 7 loopback enable ctrl */
+ u32 spd_sel_cdr_A1; /* Serdes Reg 61 spd sel cdr value for A1*/
+ u32 spd_sel_cdr; /* Serdes Reg 61 spd sel cdr value */
+ u32 use_gen_avg; /* Use generate average value */
+
+ u32 coherent; /* Coherent IO */
+};
+
+void xgene_ahci_in32(void *addr, u32 *val);
+void xgene_ahci_out32(void *addr, u32 val);
+void xgene_ahci_out32_flush(void *addr, u32 val);
+void xgene_ahci_delayus(unsigned long us);
+void xgene_ahci_delayms(unsigned long ms);
+int xgene_ahci_is_A1(void);
+
+int xgene_ahci_serdes_init(struct xgene_ahci_context *ctx,
+ int gen_sel, int clk_type, int rxwclk_inv);
+void xgene_ahci_serdes_gen_avg_val(struct xgene_ahci_context *ctx, int channel);
+void xgene_ahci_serdes_force_lat_summer_cal(struct xgene_ahci_context *ctx,
+ int channel);
+void xgene_ahci_serdes_reset_rxa_rxd(struct xgene_ahci_context *ctx,
+ int channel);
+void xgene_ahci_serdes_force_gen(struct xgene_ahci_context *ctx, int channel,
+ int gen);
+void xgene_ahci_serdes_set_pq(struct xgene_ahci_context *ctx, int channel,
+ int data);
+int xgene_ahci_port_start(struct ata_port *ap);
+int xgene_ahci_port_resume(struct ata_port *ap);
+#if defined(CONFIG_ARCH_MSLIM)
+void xgene_ahci_fill_cmd_slot(struct ahci_port_priv *pp,
+ unsigned int tag, u32 opts);
+u64 xgene_ahci_to_axi(dma_addr_t addr);
+void xgene_ahci_dflush(void *addr, int size);
+int xgene_ahci_exec_polled_cmd(struct ata_port *ap, int pmp,
+ struct ata_taskfile *tf, int is_cmd, u16 flags,
+ unsigned long timeout_msec);
+#else
+#define xgene_ahci_fill_cmd_slot ahci_fill_cmd_slot
+#define xgene_ahci_exec_polled_cmd ahci_exec_polled_cmd
+#define xgene_ahci_to_axi(x) (x)
+#define xgene_ahci_dflush(x, ...)
+#endif
+
+#endif /* __SATA_XGENE_H__ */