diff mbox

ARM: dts: imx53: Add USB support for M53EVK

Message ID 1384657490-5925-1-git-send-email-marex@denx.de (mailing list archive)
State New, archived
Headers show

Commit Message

Marek Vasut Nov. 17, 2013, 3:04 a.m. UTC 
Add USB support for M53EVK. The configuration is such that USB Host1
port is used as Host and the USB OTG port is used as Peripheral thus
far. Once OTG is properly fixed, the OTG will be further adjusted.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
---
 arch/arm/boot/dts/imx53-m53evk.dts | 22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)

Comments

Marek Vasut Nov. 18, 2013, 2:33 a.m. UTC | #1 
Hi Shawn,

> On Sun, Nov 17, 2013 at 04:04:50AM +0100, Marek Vasut wrote:
> > @@ -332,3 +343,14 @@
> > 
> >  	pinctrl-0 = <&pinctrl_uart3>;
> >  	status = "okay";
> >  
> >  };
> > 
> > +
> > +&usbotg {
> > +	dr_mode = "peripheral";
> > +	status = "okay";
> > +};
> > +
> > +&usbh1 {
> > +	vbus-supply = <&reg_usbh1_vbus>;
> > +	phy_type = "utmi";
> > +	status = "okay";
> > +};
> 
> To maintain the alphabetical order, 'usbh1' should be put before
> 'usbotg'.  I just fixed it up and applied the patch.

Ah, you're right. Thank you and sorry for adding more burden unto you.

Best regards,
Marek Vasut
Shawn Guo Nov. 18, 2013, 2:34 a.m. UTC | #2 
On Sun, Nov 17, 2013 at 04:04:50AM +0100, Marek Vasut wrote:
> @@ -332,3 +343,14 @@
>  	pinctrl-0 = <&pinctrl_uart3>;
>  	status = "okay";
>  };
> +
> +&usbotg {
> +	dr_mode = "peripheral";
> +	status = "okay";
> +};
> +
> +&usbh1 {
> +	vbus-supply = <&reg_usbh1_vbus>;
> +	phy_type = "utmi";
> +	status = "okay";
> +};

To maintain the alphabetical order, 'usbh1' should be put before
'usbotg'.  I just fixed it up and applied the patch.

Shawn
diff mbox

Patch

diff --git a/arch/arm/boot/dts/imx53-m53evk.dts b/arch/arm/boot/dts/imx53-m53evk.dts
index 47b3c89..8658e06 100644
--- a/arch/arm/boot/dts/imx53-m53evk.dts
+++ b/arch/arm/boot/dts/imx53-m53evk.dts
@@ -100,6 +100,15 @@ 
 			regulator-always-on;
 		};
 
+		reg_usbh1_vbus: regulator@3 {
+			compatible = "regulator-fixed";
+			reg = <3>;
+			regulator-name = "vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio1 2 0>;
+			enable-active-low;
+		};
 	};
 
 	sound {
@@ -228,6 +237,8 @@ 
 				MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK	0x80000000
 				MX53_PAD_EIM_EB3__GPIO2_31		0x80000000
 				MX53_PAD_PATA_DA_0__GPIO7_6		0x80000000
+				MX53_PAD_GPIO_2__GPIO1_2		0x80000000
+				MX53_PAD_GPIO_3__USBOH3_USBH1_OC	0x80000000
 			>;
 		};
 
@@ -332,3 +343,14 @@ 
 	pinctrl-0 = <&pinctrl_uart3>;
 	status = "okay";
 };
+
+&usbotg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usbh1_vbus>;
+	phy_type = "utmi";
+	status = "okay";
+};