diff mbox

[3/3] serial: amba-pl011: preseserve hardware settings during initialisation

Message ID 1386670740-16914-4-git-send-email-tixy@linaro.org (mailing list archive)
State New, archived
Headers show

Commit Message

Jon Medhurst (Tixy) Dec. 10, 2013, 10:19 a.m. UTC
During initialisation, a UART may already be in use for a console, so
take care to preserve things like baud rate and data format to avoid
corrupting console output.

Signed-off-by: Jon Medhurst <tixy@linaro.org>
---
 drivers/tty/serial/amba-pl011.c |   14 ++++++++++++--
 1 file changed, 12 insertions(+), 2 deletions(-)
diff mbox

Patch

diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c
index 8ec1729..7012ef3 100644
--- a/drivers/tty/serial/amba-pl011.c
+++ b/drivers/tty/serial/amba-pl011.c
@@ -1531,7 +1531,7 @@  static void pl011_write_lcr_h(struct uart_amba_port *uap, unsigned int lcr_h)
 static int pl011_startup(struct uart_port *port)
 {
 	struct uart_amba_port *uap = (struct uart_amba_port *)port;
-	unsigned int cr;
+	unsigned int cr, lcr_h, fbrd, ibrd;
 	int retval;
 
 	retval = pl011_hwinit(port);
@@ -1550,10 +1550,16 @@  static int pl011_startup(struct uart_port *port)
 	writew(uap->vendor->ifls, uap->port.membase + UART011_IFLS);
 
 	/*
-	 * Provoke TX FIFO interrupt into asserting.
+	 * Provoke TX FIFO interrupt into asserting. Taking care to preserve
+	 * baud rate and data format specified by FBRD, IBRD and LCRH as the
+	 * UART may already be in use as a console.
 	 */
 	spin_lock_irq(&uap->port.lock);
 
+	fbrd = readw(uap->port.membase + UART011_FBRD);
+	ibrd = readw(uap->port.membase + UART011_IBRD);
+	lcr_h = readw(uap->port.membase + uap->lcrh_rx);
+
 	cr = UART01x_CR_UARTEN | UART011_CR_TXE | UART011_CR_LBE;
 	writew(cr, uap->port.membase + UART011_CR);
 	writew(0, uap->port.membase + UART011_FBRD);
@@ -1563,6 +1569,10 @@  static int pl011_startup(struct uart_port *port)
 	while (readw(uap->port.membase + UART01x_FR) & UART01x_FR_BUSY)
 		barrier();
 
+	writew(fbrd, uap->port.membase + UART011_FBRD);
+	writew(ibrd, uap->port.membase + UART011_IBRD);
+	pl011_write_lcr_h(uap, lcr_h);
+
 	/* restore RTS and DTR */
 	cr = uap->old_cr & (UART011_CR_RTS | UART011_CR_DTR);
 	cr |= UART01x_CR_UARTEN | UART011_CR_RXE | UART011_CR_TXE;