@@ -255,6 +255,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += \
sun4i-a10-hackberry.dtb \
sun5i-a10s-olinuxino-micro.dtb \
sun5i-a13-olinuxino.dtb \
+ sun5i-a13-olinuxino-micro.dtb \
sun6i-a31-colombus.dtb \
sun7i-a20-cubieboard2.dtb \
sun7i-a20-cubietruck.dtb \
new file mode 100644
@@ -0,0 +1,68 @@
+/*
+ * Copyright 2012 Maxime Ripard
+ * Copyright 2013 Hans de Goede <hdegoede@redhat.com>
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "sun5i-a13.dtsi"
+
+/ {
+ model = "Olimex A13-Olinuxino Micro";
+ compatible = "olimex,a13-olinuxino-micro", "allwinner,sun5i-a13";
+
+ soc@01c00000 {
+ pinctrl@01c20800 {
+ led_pins_olinuxinom: led_pins@0 {
+ allwinner,pins = "PG9";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <1>;
+ allwinner,pull = <0>;
+ };
+ };
+
+ uart1: serial@01c28400 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins_b>;
+ status = "okay";
+ };
+
+ i2c0: i2c@01c2ac00 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+ };
+
+ i2c1: i2c@01c2b000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+ };
+
+ i2c2: i2c@01c2b400 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_olinuxinom>;
+
+ power {
+ label = "a13-olinuxino-micro:green:power";
+ gpios = <&pio 6 9 0>;
+ default-state = "on";
+ };
+ };
+};
The A13-OLinuXino-MICRO is a small dev-board with the Allwinner A13 SoC: https://www.olimex.com/Products/OLinuXino/A13/A13-OLinuXino-MICRO/ Features: A13 Cortex A8 processor at 1GHz, 3D Mali400 GPU 256 MB RAM (128Mbit x 16) 5VDC input power supply with own ICs, noise immune design 1 USB host 1 USB OTG which can power the board SD-card connector for booting the Linux image VGA video output LCD signals available on connector so you still can use LCD if you disable VGA/HDMI Audio output Microphone input pads (no connector) Signed-off-by: Hans de Goede <hdegoede@redhat.com> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/sun5i-a13-olinuxino-micro.dts | 68 +++++++++++++++++++++++++ 2 files changed, 69 insertions(+) create mode 100644 arch/arm/boot/dts/sun5i-a13-olinuxino-micro.dts