@@ -137,6 +137,7 @@ dtb-$(CONFIG_ARCH_MXC) += \
imx53-m53evk.dtb \
imx53-mba53.dtb \
imx53-qsb.dtb \
+ imx53-qsrb.dtb \
imx53-smd.dtb \
imx53-voipac-bsb.dtb \
imx6dl-gw51xx.dtb \
new file mode 100644
@@ -0,0 +1,158 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+
+#include "imx53-qsb-common.dtsi"
+
+/ {
+ model = "Freescale i.MX53 Quick Start-R Board";
+ compatible = "fsl,imx53-qsrb", "fsl,imx53";
+};
+
+&iomuxc {
+ i2c1 {
+ /* open drain */
+ pinctrl_i2c1_qsrb: i2c1grp-1 {
+ fsl,pins = <
+ MX53_PAD_CSI0_DAT8__I2C1_SDA 0x400001ec
+ MX53_PAD_CSI0_DAT9__I2C1_SCL 0x400001ec
+ >;
+ };
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1_qsrb>;
+ status = "okay";
+
+ pmic: mc34708@8 {
+ compatible = "fsl,mc34708";
+ reg = <0x08>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <23 0x8>;
+ regulators {
+ sw1_reg: sw1a {
+ regulator-name = "SW1";
+ regulator-min-microvolt = <650000>;
+ regulator-max-microvolt = <1437500>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw1b_reg: sw1b {
+ regulator-name = "SW1B";
+ regulator-min-microvolt = <650000>;
+ regulator-max-microvolt = <1437500>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw2_reg: sw2 {
+ regulator-name = "SW2";
+ regulator-min-microvolt = <650000>;
+ regulator-max-microvolt = <1437500>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3_reg: sw3 {
+ regulator-name = "SW3";
+ regulator-min-microvolt = <650000>;
+ regulator-max-microvolt = <1425000>;
+ regulator-boot-on;
+ };
+
+ sw4a_reg: sw4a {
+ regulator-name = "SW4A";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw4b_reg: sw4b {
+ regulator-name = "SW4B";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw5_reg: sw5 {
+ regulator-name = "SW5";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ swbst_reg: swbst {
+ regulator-name = "SWBST";
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vpll_reg: vpll {
+ regulator-name = "VPLL";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ };
+
+ vrefddr_reg: vrefddr {
+ regulator-name = "VREFDDR";
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vusb_reg: vusb {
+ regulator-name = "VUSB";
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vusb2_reg: vusb2 {
+ regulator-name = "VUSB2";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vdac_reg: vdac {
+ regulator-name = "VDAC";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2775000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen1_reg: vgen1 {
+ regulator-name = "VGEN1";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1550000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen2_reg: vgen2 {
+ regulator-name = "VGEN2";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+};
The "Start-R QSB" has a different PMIC than the older "Start QSB". Add a new devicetree for the Start-R. They both could use the same DT, as both PMICs (the dialog and the mc34708) have different i2c addresses and could coexist in the same DT without any errors. But once phandles are used, this will get messy. The pmic nodes are based on an earlier patch [PATCH] arm: imx53-qsb: Add Ripley driver DT nodes from Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org> which apparently got lost/abandoned. I added phandles/newlines and changed the node name from ripley to mc34708. Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx53-qsrb.dts | 158 +++++++++++++++++++++++++++++++++++++++ 2 files changed, 159 insertions(+) create mode 100644 arch/arm/boot/dts/imx53-qsrb.dts