diff mbox

[v2,1/5] ARM: dts: omap3: Add support for INCOstartec a83x module

Message ID 1390417460-3134-2-git-send-email-chf.fritz@googlemail.com (mailing list archive)
State New, archived
Headers show

Commit Message

Christoph Fritz Jan. 22, 2014, 7:04 p.m. UTC
INCOstartec LILLY-A83X module is a TI DM3730xx100 (OMAP3) SoC
computer-on-module.

This patch adds device tree support for most of its features.

Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
---
 arch/arm/boot/dts/omap3-lilly-a83x.dtsi |  445 +++++++++++++++++++++++++++++++
 1 file changed, 445 insertions(+)
 create mode 100644 arch/arm/boot/dts/omap3-lilly-a83x.dtsi

Comments

Nishanth Menon Jan. 22, 2014, 7:48 p.m. UTC | #1
On 01/22/2014 01:04 PM, Christoph Fritz wrote:
> INCOstartec LILLY-A83X module is a TI DM3730xx100 (OMAP3) SoC
> computer-on-module.
> 
> This patch adds device tree support for most of its features.
> 
> Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
> ---
>  arch/arm/boot/dts/omap3-lilly-a83x.dtsi |  445 +++++++++++++++++++++++++++++++
>  1 file changed, 445 insertions(+)
>  create mode 100644 arch/arm/boot/dts/omap3-lilly-a83x.dtsi
> 
> diff --git a/arch/arm/boot/dts/omap3-lilly-a83x.dtsi b/arch/arm/boot/dts/omap3-lilly-a83x.dtsi
> new file mode 100644
> index 0000000..5e2137a
> --- /dev/null
> +++ b/arch/arm/boot/dts/omap3-lilly-a83x.dtsi
> @@ -0,0 +1,445 @@
> +/*
> + * Copyright (C) 2014 Christoph Fritz <chf.fritzc@googlemail.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + */
> +
> +#include "omap36xx.dtsi"
> +
> +/ {
> +	model = "INCOstartec LILLY-A83X module (DM3730)";
> +	compatible = "incostartec,omap3-lilly-a83x", "ti,omap36xx", "ti,omap3";
> +
> +	chosen {
> +			bootargs = "console=ttyO0,115200n8 vt.global_cursor_default=0 consoleblank=0";
> +	};
> +
> +	memory {
> +		device_type = "memory";
> +		reg = <0x80000000 0x8000000>;   /* 128 MB */
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		heartbeat1 {
> +			label = "lilly-a83x::led1";
> +			gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
> +			linux,default-trigger = "default-on";
> +		};
> +
> +	};
> +
> +	sound {
> +		compatible = "ti,omap-twl4030";
> +		ti,model = "lilly-a83x";
> +
> +		ti,mcbsp = <&mcbsp2>;
> +		ti,codec = <&twl_audio>;
> +	};
> +
> +	regulators {
> +		compatible = "simple-bus";
Shrug, just moving the fixed regulator to root also will do the job,
not sure simple-bus much sense here :(

> +		reg_vcc3: vcc3 {
> +                        compatible = "regulator-fixed";
> +                        regulator-name = "VCC3";
> +                        regulator-min-microvolt = <3300000>;
> +                        regulator-max-microvolt = <3300000>;
> +                        regulator-always-on;
> +		};
> +	};
> +
> +	hsusb1_phy: hsusb1_phy {
> +		compatible = "usb-nop-xceiv";
> +		vcc-supply = <&reg_vcc3>;
> +	};
> +};
> +
> +&omap3_pmx_wkup {
> +	pinctrl-names = "default";
> +
> +	lan9221_pins: pinmux_lan9221_pins {
> +		pinctrl-single,pins = <
> +			0x5A (PIN_INPUT | MUX_MODE4)   /* gpio_129 */
umm.. you might want to follow the convention as you followed later in
comments.
> +		>;
> +	};
> +
> +	tsc2048_pins: pinmux_tsc2048_pins {
> +		pinctrl-single,pins = <
> +			0x16 (PIN_INPUT_PULLUP | MUX_MODE4)   /* gpio_8 */
umm.. you might want to follow the convention as you followed later in
comments.
> +		>;
> +	};
> +
> +	mmc1cd_pins: pinmux_mmc1cd_pins {
> +		pinctrl-single,pins = <
> +			0x56 (PIN_INPUT | MUX_MODE4)   /* gpio_126 */
umm.. you might want to follow the convention as you followed later in
comments.
> +		>;
> +	};
> +};
> +
> +&omap3_pmx_core {
> +	pinctrl-names = "default";
> +
> +	gpio1_pins: pinmux_gpio1_pins {
> +		pinctrl-single,pins = <
> +			0x5ca (PIN_OUTPUT_PULLDOWN | MUX_MODE4)   /* gpio_29 */
umm.. you might want to follow the convention as you followed later in
comments.
> +		>;
> +	};
> +
> +	uart1_pins: pinmux_uart1_pins {
> +		pinctrl-single,pins = <
> +			0x14c (PIN_OUTPUT | MUX_MODE0)   /* uart1_tx.uart1_tx */
> +			0x14e (PIN_OUTPUT | MUX_MODE0)   /* uart1_rts.uart1_rts */
> +			0x150 (PIN_INPUT | MUX_MODE0)    /* uart1_cts.uart1_cts */
> +			0x152 (PIN_INPUT | MUX_MODE0)    /* uart1_rx.uart1_rx */
> +		>;
you may be interested in include/dt-bindings/pinctrl/omap.h
OMAP3_CORE1_IOPAD, OMAP3_CORE2_IOPAD as needed here.

> +	};
> +
> +	uart2_pins: pinmux_uart2_pins {
> +		pinctrl-single,pins = <
> +			0x140 (PIN_OUTPUT | MUX_MODE1)   /* mcbsp3_clkx.uart2_tx */
> +			0x142 (PIN_INPUT | MUX_MODE1)    /* mcbsp3_fsx.uart2_rx */
> +		>;
> +	};
> +
> +	uart3_pins: pinmux_uart3_pins {
> +		pinctrl-single,pins = <
> +			0x16e (PIN_INPUT | MUX_MODE0)    /* uart3_rx_irrx.uart3_rx_irrx */
> +			0x170 (PIN_OUTPUT | MUX_MODE0)   /* uart3_tx_irtx.uart3_tx_irtx */
> +		>;
> +	};
> +
> +	i2c1_pins: pinmux_i2c1_pins {
> +		pinctrl-single,pins = <
> +			0x18a (PIN_INPUT_PULLUP | MUX_MODE0)    /* i2c1_scl */
> +			0x18c (PIN_INPUT_PULLUP | MUX_MODE0)    /* i2c1_sda */
umm.. you might want to follow the convention as you followed
elsewhere in comments.
> +		>;
> +	};
> +
> +	i2c2_pins: pinmux_i2c2_pins {
> +		pinctrl-single,pins = <
> +			0x18e (PIN_INPUT | MUX_MODE0)   /* i2c2_scl.i2c2_scl */
> +			0x190 (PIN_INPUT | MUX_MODE0)   /* i2c2_sda.i2c2_sda */
> +		>;
> +	};
> +
> +	i2c3_pins: pinmux_i2c3_pins {
> +		pinctrl-single,pins = <
> +			0x192 (PIN_INPUT | MUX_MODE0)   /* i2c3_scl.i2c3_scl */
> +			0x194 (PIN_INPUT | MUX_MODE0)   /* i2c3_sda.i2c3_sda */
> +		>;
> +	};
> +
> +	hsusb1_pins: pinmux_hsusb1_pins {
> +		pinctrl-single,pins = <
> +			0x5a8 (PIN_OUTPUT | MUX_MODE3)  /* etk_clk.hsusb1_stp */
&omap3_pmx_core2 and OMAP3_CORE2_IOPAD probably here. and probably see
similar usage in other board dtsi.
> +			0x5aa (PIN_INPUT | MUX_MODE3)   /* etk_ctl.hsusb1_clk */
> +			0x5ac (PIN_INPUT | MUX_MODE3)   /* etk_d0.hsusb1_data0 */
> +			0x5ae (PIN_INPUT | MUX_MODE3)   /* etk_d1.hsusb1_data1 */
> +			0x5b0 (PIN_INPUT | MUX_MODE3)   /* etk_d2.hsusb1_data2 */
> +			0x5b2 (PIN_INPUT | MUX_MODE3)   /* etk_d3.hsusb1_data7 */
> +			0x5b4 (PIN_INPUT | MUX_MODE3)   /* etk_d4.hsusb1_data4 */
> +			0x5b6 (PIN_INPUT | MUX_MODE3)   /* etk_d5.hsusb1_data5 */
> +			0x5b8 (PIN_INPUT | MUX_MODE3)   /* etk_d6.hsusb1_data6 */
> +			0x5ba (PIN_INPUT | MUX_MODE3)   /* etk_d7.hsusb1_data3 */
> +			0x5bc (PIN_INPUT | MUX_MODE3)   /* etk_d8.hsusb1_dir */
> +			0x5be (PIN_INPUT | MUX_MODE3)   /* etk_d9.hsusb1_nxt */
> +
> +			/* GPIO 128 controls USB-Hub reset. But USB-Phy its
> +			 * reset can't be controlled. So we clamp this GPIO to
> +			 * high (PIN_OFF_OUTPUT_HIGH) to always enable USB-Hub.
> +			 */
> +
> +			0x1ae (PIN_OUTPUT_PULLUP | PIN_OFF_OUTPUT_HIGH | MUX_MODE4)   /* gpio_182 */
> +		>;
> +	};
> +
> +	hsusb_otg_pins: pinmux_hsusb_otg_pins {
> +		pinctrl-single,pins = <
> +			0x172 (PIN_INPUT | MUX_MODE0)   /* hsusb0_clk.hsusb0_clk */
> +			0x174 (PIN_OUTPUT | MUX_MODE0)  /* hsusb0_stp.hsusb0_stp */
> +			0x176 (PIN_INPUT | MUX_MODE0)   /* hsusb0_dir.hsusb0_dir */
> +			0x178 (PIN_INPUT | MUX_MODE0)   /* hsusb0_nxt.hsusb0_nxt */
> +			0x17a (PIN_INPUT | MUX_MODE0)   /* hsusb0_data0.hsusb0_data0 */
> +			0x17c (PIN_INPUT | MUX_MODE0)   /* hsusb0_data1.hsusb0_data1 */
> +			0x17e (PIN_INPUT | MUX_MODE0)   /* hsusb0_data2.hsusb0_data2 */
> +			0x180 (PIN_INPUT | MUX_MODE0)   /* hsusb0_data3.hsusb0_data3 */
> +			0x182 (PIN_INPUT | MUX_MODE0)   /* hsusb0_data4.hsusb0_data4 */
> +			0x184 (PIN_INPUT | MUX_MODE0)   /* hsusb0_data5.hsusb0_data5 */
> +			0x186 (PIN_INPUT | MUX_MODE0)   /* hsusb0_data6.hsusb0_data6 */
> +			0x188 (PIN_INPUT | MUX_MODE0)   /* hsusb0_data7.hsusb0_data7 */
> +		>;
> +	};
> +
> +	mmc1_pins: pinmux_mmc1_pins {
> +		pinctrl-single,pins = <
> +			0x114 (PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc1_clk.sdmmc1_clk */
> +			0x116 (PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc1_cmd.sdmmc1_cmd */
> +			0x118 (PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc1_dat0.sdmmc1_dat0 */
> +			0x11a (PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc1_dat1.sdmmc1_dat1 */
> +			0x11c (PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc1_dat2.sdmmc1_dat2 */
> +			0x11e (PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc1_dat3.sdmmc1_dat3 */
> +		>;
> +	};
> +
> +	spi2_pins: pinmux_spi2_pins {
> +		pinctrl-single,pins = <
> +			0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE0)   /* mcspi2_clk.mcspi2_clk */
> +			0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE0)   /* mcspi2_simo.mcspi2_simo */
> +			0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE0)   /* mcspi2_somi.mcspi2_somi */
> +			0x1ac (PIN_OUTPUT | MUX_MODE0)   /* mcspi2_cs0.mcspi2_cs0 */
> +		>;
> +	};
> +};
> +
> +&gpio1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&gpio1_pins>;
> +};
> +
> +&i2c1 {
> +	clock-frequency = <2600000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c1_pins>;
> +
> +	twl: twl@48 {
> +		reg = <0x48>;
> +		interrupts = <7>;   /* SYS_NIRQ cascaded to intc */
> +		interrupt-parent = <&intc>;
> +
> +		twl_audio: audio {
> +			compatible = "ti,twl4030-audio";
> +			codec {
> +			};
> +		};
> +	};
> +};
> +
> +#include "twl4030.dtsi"
> +#include "twl4030_omap3.dtsi"
> +
> +&twl {
> +	vmmc1: regulator-vmmc1 {
> +		regulator-always-on;
> +	};
> +
> +	vdd1: regulator-vdd1 {
> +		regulator-always-on;
> +	};
> +
> +	vdd2: regulator-vdd2 {
> +		regulator-always-on;
> +	};
I hope you have covered all required regulators here including the
ones you might need for IO.1P8 perhaps?

> +};
> +
> +&i2c2 {
> +	clock-frequency = <2600000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c2_pins>;
> +};
> +
> +&i2c3 {
> +	clock-frequency = <2600000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c3_pins>;
> +		gpiom1: gpio@20 {
> +			compatible = "mcp,mcp23017";
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +			reg = <0x20>;
> +		};
> +};
> +
> +&uart1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart1_pins>;
> +};
> +
> +&uart2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart2_pins>;
> +};
> +
> +&uart3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart3_pins>;
> +};
> +
> +&uart4 {
> +	status = "disabled";
> +};
> +
> +&mmc1 {
> +	reg = <0x4809c000 0x400>;
little curious as to why this. is that to override length 0x200 to
0x400? that belongs to soc.dtsi then.

> +	cd-gpios = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>;
> +	cd-inverted;
> +	vmmc-supply = <&vmmc1>;
> +	bus-width = <4>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mmc1_pins &mmc1cd_pins>;
> +	cap-sdio-irq;
> +	cap-sd-highspeed;
> +	cap-mmc-highspeed;
> +};
> +
> +&mmc2 {
> +	status = "disabled";
> +};
> +
> +&mmc3 {
> +	status = "disabled";
> +};
> +
> +&mcspi2 {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&spi2_pins>;
> +
> +	tsc2046@0 {
> +		reg = <0>;   /* CS0 */
> +		compatible = "ti,tsc2046";
> +		interrupt-parent = <&gpio1>;
> +		interrupts = <8 0>;   /* boot6 / gpio_8 */
> +		spi-max-frequency = <1000000>;
> +		pendown-gpio = <&gpio1 8 0>;
> +		vcc-supply = <&reg_vcc3>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&tsc2048_pins>;
> +
> +		ti,x-min = <300>;
> +		ti,x-max = <3000>;
> +		ti,y-min = <600>;
> +		ti,y-max = <3600>;
> +		ti,x-plate-ohms = <80>;
> +		ti,pressure-max = <255>;
> +		ti,swap-xy;
> +
> +		linux,wakeup;
> +	};
> +};
> +
> +&usbhsehci {
> +	phys = <&hsusb1_phy>;
> +};
> +
> +&usbhshost {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&hsusb1_pins>;
> +	num-ports = <2>;
> +	port1-mode = "ehci-phy";
> +};
> +
> +&usb_otg_hs {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&hsusb_otg_pins>;
> +	interface-type = <0>;
> +	usb-phy = <&usb2_phy>;
> +	phys = <&usb2_phy>;
> +	phy-names = "usb2-phy";
> +	mode = <3>;
> +	power = <50>;
> +};
> +
> +&gpmc {
> +	ranges = <0 0 0x30000000 0x1000000>,
> +		<7 0 0x15000000 0x01000000>;
> +
> +	nand@0,0 {
> +		reg = <0 0 0x1000000>;
> +		nand-bus-width = <16>;
> +		ti,nand-ecc-opt = "bch8";
> +		/* no elm on omap3 */
> +
> +		gpmc,mux-add-data = <0>;
> +		gpmc,device-nand;
> +		gpmc,device-width = <2>;
> +		gpmc,wait-pin = <0>;
> +		gpmc,wait-monitoring-ns = <0>;
> +		gpmc,burst-length= <4>;
> +		gpmc,cs-on-ns = <0>;
> +		gpmc,cs-rd-off-ns = <100>;
> +		gpmc,cs-wr-off-ns = <100>;
> +		gpmc,adv-on-ns = <0>;
> +		gpmc,adv-rd-off-ns = <100>;
> +		gpmc,adv-wr-off-ns = <100>;
> +		gpmc,oe-on-ns = <5>;
> +		gpmc,oe-off-ns = <75>;
> +		gpmc,we-on-ns = <5>;
> +		gpmc,we-off-ns = <75>;
> +		gpmc,rd-cycle-ns = <100>;
> +		gpmc,wr-cycle-ns = <100>;
> +		gpmc,access-ns = <60>;
> +		gpmc,page-burst-access-ns = <5>;
> +		gpmc,bus-turnaround-ns = <0>;
> +		gpmc,cycle2cycle-samecsen;
> +		gpmc,cycle2cycle-delay-ns = <50>;
> +		gpmc,wr-data-mux-bus-ns = <75>;
> +		gpmc,wr-access-ns = <155>;
> +
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +
> +		partition@0 {
> +			label = "MLO";
> +			reg = <0 0x80000>;
> +		};
> +
> +		partition@0x80000 {
> +			label = "u-boot";
> +			reg = <0x80000 0x1e0000>;
> +		};
> +
> +		partition@0x260000 {
> +			label = "u-boot-environment";
> +			reg = <0x260000 0x20000>;
> +		};
> +
> +		partition@0x280000 {
> +			label = "kernel";
> +			reg = <0x280000 0x500000>;
> +		};
> +
> +		partition@0x780000 {
> +			label = "filesystem";
> +			reg = <0x780000 0xf880000>;
> +		};
> +	};
> +
> +	ethernet@7,0 {
> +		compatible = "smsc,lan9221", "smsc,lan9115";
> +		bank-width = <2>;
> +		gpmc,mux-add-data = <2>;
> +		gpmc,cs-on-ns = <10>;
> +		gpmc,cs-rd-off-ns = <60>;
> +		gpmc,cs-wr-off-ns = <60>;
> +		gpmc,adv-on-ns = <0>;
> +		gpmc,adv-rd-off-ns = <10>;
> +		gpmc,adv-wr-off-ns = <10>;
> +		gpmc,oe-on-ns = <10>;
> +		gpmc,oe-off-ns = <60>;
> +		gpmc,we-on-ns = <10>;
> +		gpmc,we-off-ns = <60>;
> +		gpmc,rd-cycle-ns = <100>;
> +		gpmc,wr-cycle-ns = <100>;
> +		gpmc,access-ns = <50>;
> +		gpmc,page-burst-access-ns = <5>;
> +		gpmc,bus-turnaround-ns = <0>;
> +		gpmc,cycle2cycle-delay-ns = <75>;
> +		gpmc,wr-data-mux-bus-ns = <15>;
> +		gpmc,wr-access-ns = <75>;
> +		gpmc,cycle2cycle-samecsen;
> +		gpmc,cycle2cycle-diffcsen;
> +		vddvario-supply = <&reg_vcc3>;
> +		vdd33a-supply = <&reg_vcc3>;
> +		reg-io-width = <4>;
> +		interrupt-parent = <&gpio5>;
> +		interrupts = <1 0x2>;
> +		reg = <7 0 0xff>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&lan9221_pins>;
> +		phy-mode = "mii";
> +	};
> +};
>
Christoph Fritz Jan. 27, 2014, 12:04 a.m. UTC | #2
Hi Nishanth,

 thanks for reviewing this patch. Please see my comments below.

On Wed, Jan 22, 2014 at 01:48:14PM -0600, Nishanth Menon wrote:
> On 01/22/2014 01:04 PM, Christoph Fritz wrote:

> > +	regulators {
> > +		compatible = "simple-bus";
> Shrug, just moving the fixed regulator to root also will do the job,
> not sure simple-bus much sense here :(
> 

will get fixed

> > +		reg_vcc3: vcc3 {
> > +                        compatible = "regulator-fixed";
> > +                        regulator-name = "VCC3";
> > +                        regulator-min-microvolt = <3300000>;
> > +                        regulator-max-microvolt = <3300000>;
> > +                        regulator-always-on;
> > +		};
> > +	};
> > +
> > +	hsusb1_phy: hsusb1_phy {
> > +		compatible = "usb-nop-xceiv";
> > +		vcc-supply = <&reg_vcc3>;
> > +	};
> > +};
> > +
> > +&omap3_pmx_wkup {
> > +	pinctrl-names = "default";
> > +
> > +	lan9221_pins: pinmux_lan9221_pins {
> > +		pinctrl-single,pins = <
> > +			0x5A (PIN_INPUT | MUX_MODE4)   /* gpio_129 */
> umm.. you might want to follow the convention as you followed later in
> comments.

My convention was: If pin can be described unique with one name,
don't use two. But I'll change that to be uniform with all comments.

> > +		>;
> > +	};
> > +
> > +	tsc2048_pins: pinmux_tsc2048_pins {
> > +		pinctrl-single,pins = <
> > +			0x16 (PIN_INPUT_PULLUP | MUX_MODE4)   /* gpio_8 */
> umm.. you might want to follow the convention as you followed later in
> comments.

will get fixed

> > +		>;
> > +	};
> > +
> > +	mmc1cd_pins: pinmux_mmc1cd_pins {
> > +		pinctrl-single,pins = <
> > +			0x56 (PIN_INPUT | MUX_MODE4)   /* gpio_126 */
> umm.. you might want to follow the convention as you followed later in
> comments.

will get fixed

> > +		>;
> > +	};
> > +};
> > +
> > +&omap3_pmx_core {
> > +	pinctrl-names = "default";
> > +
> > +	gpio1_pins: pinmux_gpio1_pins {
> > +		pinctrl-single,pins = <
> > +			0x5ca (PIN_OUTPUT_PULLDOWN | MUX_MODE4)   /* gpio_29 */
> umm.. you might want to follow the convention as you followed later in
> comments.

will get fixed

> > +		>;
> > +	};
> > +
> > +	uart1_pins: pinmux_uart1_pins {
> > +		pinctrl-single,pins = <
> > +			0x14c (PIN_OUTPUT | MUX_MODE0)   /* uart1_tx.uart1_tx */
> > +			0x14e (PIN_OUTPUT | MUX_MODE0)   /* uart1_rts.uart1_rts */
> > +			0x150 (PIN_INPUT | MUX_MODE0)    /* uart1_cts.uart1_cts */
> > +			0x152 (PIN_INPUT | MUX_MODE0)    /* uart1_rx.uart1_rx */
> > +		>;
> you may be interested in include/dt-bindings/pinctrl/omap.h
> OMAP3_CORE1_IOPAD, OMAP3_CORE2_IOPAD as needed here.

will get fixed

> > +	};
> > +
> > +	uart2_pins: pinmux_uart2_pins {
> > +		pinctrl-single,pins = <
> > +			0x140 (PIN_OUTPUT | MUX_MODE1)   /* mcbsp3_clkx.uart2_tx */
> > +			0x142 (PIN_INPUT | MUX_MODE1)    /* mcbsp3_fsx.uart2_rx */
> > +		>;
> > +	};
> > +
> > +	uart3_pins: pinmux_uart3_pins {
> > +		pinctrl-single,pins = <
> > +			0x16e (PIN_INPUT | MUX_MODE0)    /* uart3_rx_irrx.uart3_rx_irrx */
> > +			0x170 (PIN_OUTPUT | MUX_MODE0)   /* uart3_tx_irtx.uart3_tx_irtx */
> > +		>;
> > +	};
> > +
> > +	i2c1_pins: pinmux_i2c1_pins {
> > +		pinctrl-single,pins = <
> > +			0x18a (PIN_INPUT_PULLUP | MUX_MODE0)    /* i2c1_scl */
> > +			0x18c (PIN_INPUT_PULLUP | MUX_MODE0)    /* i2c1_sda */
> umm.. you might want to follow the convention as you followed
> elsewhere in comments.

will get fixed

> > +		>;
> > +	};
> > +
> > +	i2c2_pins: pinmux_i2c2_pins {
> > +		pinctrl-single,pins = <
> > +			0x18e (PIN_INPUT | MUX_MODE0)   /* i2c2_scl.i2c2_scl */
> > +			0x190 (PIN_INPUT | MUX_MODE0)   /* i2c2_sda.i2c2_sda */
> > +		>;
> > +	};
> > +
> > +	i2c3_pins: pinmux_i2c3_pins {
> > +		pinctrl-single,pins = <
> > +			0x192 (PIN_INPUT | MUX_MODE0)   /* i2c3_scl.i2c3_scl */
> > +			0x194 (PIN_INPUT | MUX_MODE0)   /* i2c3_sda.i2c3_sda */
> > +		>;
> > +	};
> > +
> > +	hsusb1_pins: pinmux_hsusb1_pins {
> > +		pinctrl-single,pins = <
> > +			0x5a8 (PIN_OUTPUT | MUX_MODE3)  /* etk_clk.hsusb1_stp */
> &omap3_pmx_core2 and OMAP3_CORE2_IOPAD probably here. and probably see
> similar usage in other board dtsi.

will get fixed

> > +
> > +#include "twl4030.dtsi"
> > +#include "twl4030_omap3.dtsi"
> > +
> > +&twl {
> > +	vmmc1: regulator-vmmc1 {
> > +		regulator-always-on;
> > +	};
> > +
> > +	vdd1: regulator-vdd1 {
> > +		regulator-always-on;
> > +	};
> > +
> > +	vdd2: regulator-vdd2 {
> > +		regulator-always-on;
> > +	};
> I hope you have covered all required regulators here including the
> ones you might need for IO.1P8 perhaps?

Yes, I rechecked all and it's fine now. IO.1P8 was low due to a
hardware error which is now fixed.

> > +
> > +&mmc1 {
> > +	reg = <0x4809c000 0x400>;
> little curious as to why this. is that to override length 0x200 to
> 0x400? that belongs to soc.dtsi then.

This is a remnant from last year and will get purged.

Let me reroll this patch in a new v3 set.

Thanks
  -- Christoph
diff mbox

Patch

diff --git a/arch/arm/boot/dts/omap3-lilly-a83x.dtsi b/arch/arm/boot/dts/omap3-lilly-a83x.dtsi
new file mode 100644
index 0000000..5e2137a
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-lilly-a83x.dtsi
@@ -0,0 +1,445 @@ 
+/*
+ * Copyright (C) 2014 Christoph Fritz <chf.fritzc@googlemail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include "omap36xx.dtsi"
+
+/ {
+	model = "INCOstartec LILLY-A83X module (DM3730)";
+	compatible = "incostartec,omap3-lilly-a83x", "ti,omap36xx", "ti,omap3";
+
+	chosen {
+			bootargs = "console=ttyO0,115200n8 vt.global_cursor_default=0 consoleblank=0";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x8000000>;   /* 128 MB */
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		heartbeat1 {
+			label = "lilly-a83x::led1";
+			gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+	};
+
+	sound {
+		compatible = "ti,omap-twl4030";
+		ti,model = "lilly-a83x";
+
+		ti,mcbsp = <&mcbsp2>;
+		ti,codec = <&twl_audio>;
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		reg_vcc3: vcc3 {
+                        compatible = "regulator-fixed";
+                        regulator-name = "VCC3";
+                        regulator-min-microvolt = <3300000>;
+                        regulator-max-microvolt = <3300000>;
+                        regulator-always-on;
+		};
+	};
+
+	hsusb1_phy: hsusb1_phy {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&reg_vcc3>;
+	};
+};
+
+&omap3_pmx_wkup {
+	pinctrl-names = "default";
+
+	lan9221_pins: pinmux_lan9221_pins {
+		pinctrl-single,pins = <
+			0x5A (PIN_INPUT | MUX_MODE4)   /* gpio_129 */
+		>;
+	};
+
+	tsc2048_pins: pinmux_tsc2048_pins {
+		pinctrl-single,pins = <
+			0x16 (PIN_INPUT_PULLUP | MUX_MODE4)   /* gpio_8 */
+		>;
+	};
+
+	mmc1cd_pins: pinmux_mmc1cd_pins {
+		pinctrl-single,pins = <
+			0x56 (PIN_INPUT | MUX_MODE4)   /* gpio_126 */
+		>;
+	};
+};
+
+&omap3_pmx_core {
+	pinctrl-names = "default";
+
+	gpio1_pins: pinmux_gpio1_pins {
+		pinctrl-single,pins = <
+			0x5ca (PIN_OUTPUT_PULLDOWN | MUX_MODE4)   /* gpio_29 */
+		>;
+	};
+
+	uart1_pins: pinmux_uart1_pins {
+		pinctrl-single,pins = <
+			0x14c (PIN_OUTPUT | MUX_MODE0)   /* uart1_tx.uart1_tx */
+			0x14e (PIN_OUTPUT | MUX_MODE0)   /* uart1_rts.uart1_rts */
+			0x150 (PIN_INPUT | MUX_MODE0)    /* uart1_cts.uart1_cts */
+			0x152 (PIN_INPUT | MUX_MODE0)    /* uart1_rx.uart1_rx */
+		>;
+	};
+
+	uart2_pins: pinmux_uart2_pins {
+		pinctrl-single,pins = <
+			0x140 (PIN_OUTPUT | MUX_MODE1)   /* mcbsp3_clkx.uart2_tx */
+			0x142 (PIN_INPUT | MUX_MODE1)    /* mcbsp3_fsx.uart2_rx */
+		>;
+	};
+
+	uart3_pins: pinmux_uart3_pins {
+		pinctrl-single,pins = <
+			0x16e (PIN_INPUT | MUX_MODE0)    /* uart3_rx_irrx.uart3_rx_irrx */
+			0x170 (PIN_OUTPUT | MUX_MODE0)   /* uart3_tx_irtx.uart3_tx_irtx */
+		>;
+	};
+
+	i2c1_pins: pinmux_i2c1_pins {
+		pinctrl-single,pins = <
+			0x18a (PIN_INPUT_PULLUP | MUX_MODE0)    /* i2c1_scl */
+			0x18c (PIN_INPUT_PULLUP | MUX_MODE0)    /* i2c1_sda */
+		>;
+	};
+
+	i2c2_pins: pinmux_i2c2_pins {
+		pinctrl-single,pins = <
+			0x18e (PIN_INPUT | MUX_MODE0)   /* i2c2_scl.i2c2_scl */
+			0x190 (PIN_INPUT | MUX_MODE0)   /* i2c2_sda.i2c2_sda */
+		>;
+	};
+
+	i2c3_pins: pinmux_i2c3_pins {
+		pinctrl-single,pins = <
+			0x192 (PIN_INPUT | MUX_MODE0)   /* i2c3_scl.i2c3_scl */
+			0x194 (PIN_INPUT | MUX_MODE0)   /* i2c3_sda.i2c3_sda */
+		>;
+	};
+
+	hsusb1_pins: pinmux_hsusb1_pins {
+		pinctrl-single,pins = <
+			0x5a8 (PIN_OUTPUT | MUX_MODE3)  /* etk_clk.hsusb1_stp */
+			0x5aa (PIN_INPUT | MUX_MODE3)   /* etk_ctl.hsusb1_clk */
+			0x5ac (PIN_INPUT | MUX_MODE3)   /* etk_d0.hsusb1_data0 */
+			0x5ae (PIN_INPUT | MUX_MODE3)   /* etk_d1.hsusb1_data1 */
+			0x5b0 (PIN_INPUT | MUX_MODE3)   /* etk_d2.hsusb1_data2 */
+			0x5b2 (PIN_INPUT | MUX_MODE3)   /* etk_d3.hsusb1_data7 */
+			0x5b4 (PIN_INPUT | MUX_MODE3)   /* etk_d4.hsusb1_data4 */
+			0x5b6 (PIN_INPUT | MUX_MODE3)   /* etk_d5.hsusb1_data5 */
+			0x5b8 (PIN_INPUT | MUX_MODE3)   /* etk_d6.hsusb1_data6 */
+			0x5ba (PIN_INPUT | MUX_MODE3)   /* etk_d7.hsusb1_data3 */
+			0x5bc (PIN_INPUT | MUX_MODE3)   /* etk_d8.hsusb1_dir */
+			0x5be (PIN_INPUT | MUX_MODE3)   /* etk_d9.hsusb1_nxt */
+
+			/* GPIO 128 controls USB-Hub reset. But USB-Phy its
+			 * reset can't be controlled. So we clamp this GPIO to
+			 * high (PIN_OFF_OUTPUT_HIGH) to always enable USB-Hub.
+			 */
+
+			0x1ae (PIN_OUTPUT_PULLUP | PIN_OFF_OUTPUT_HIGH | MUX_MODE4)   /* gpio_182 */
+		>;
+	};
+
+	hsusb_otg_pins: pinmux_hsusb_otg_pins {
+		pinctrl-single,pins = <
+			0x172 (PIN_INPUT | MUX_MODE0)   /* hsusb0_clk.hsusb0_clk */
+			0x174 (PIN_OUTPUT | MUX_MODE0)  /* hsusb0_stp.hsusb0_stp */
+			0x176 (PIN_INPUT | MUX_MODE0)   /* hsusb0_dir.hsusb0_dir */
+			0x178 (PIN_INPUT | MUX_MODE0)   /* hsusb0_nxt.hsusb0_nxt */
+			0x17a (PIN_INPUT | MUX_MODE0)   /* hsusb0_data0.hsusb0_data0 */
+			0x17c (PIN_INPUT | MUX_MODE0)   /* hsusb0_data1.hsusb0_data1 */
+			0x17e (PIN_INPUT | MUX_MODE0)   /* hsusb0_data2.hsusb0_data2 */
+			0x180 (PIN_INPUT | MUX_MODE0)   /* hsusb0_data3.hsusb0_data3 */
+			0x182 (PIN_INPUT | MUX_MODE0)   /* hsusb0_data4.hsusb0_data4 */
+			0x184 (PIN_INPUT | MUX_MODE0)   /* hsusb0_data5.hsusb0_data5 */
+			0x186 (PIN_INPUT | MUX_MODE0)   /* hsusb0_data6.hsusb0_data6 */
+			0x188 (PIN_INPUT | MUX_MODE0)   /* hsusb0_data7.hsusb0_data7 */
+		>;
+	};
+
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			0x114 (PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc1_clk.sdmmc1_clk */
+			0x116 (PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc1_cmd.sdmmc1_cmd */
+			0x118 (PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc1_dat0.sdmmc1_dat0 */
+			0x11a (PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc1_dat1.sdmmc1_dat1 */
+			0x11c (PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc1_dat2.sdmmc1_dat2 */
+			0x11e (PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc1_dat3.sdmmc1_dat3 */
+		>;
+	};
+
+	spi2_pins: pinmux_spi2_pins {
+		pinctrl-single,pins = <
+			0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE0)   /* mcspi2_clk.mcspi2_clk */
+			0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE0)   /* mcspi2_simo.mcspi2_simo */
+			0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE0)   /* mcspi2_somi.mcspi2_somi */
+			0x1ac (PIN_OUTPUT | MUX_MODE0)   /* mcspi2_cs0.mcspi2_cs0 */
+		>;
+	};
+};
+
+&gpio1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpio1_pins>;
+};
+
+&i2c1 {
+	clock-frequency = <2600000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+
+	twl: twl@48 {
+		reg = <0x48>;
+		interrupts = <7>;   /* SYS_NIRQ cascaded to intc */
+		interrupt-parent = <&intc>;
+
+		twl_audio: audio {
+			compatible = "ti,twl4030-audio";
+			codec {
+			};
+		};
+	};
+};
+
+#include "twl4030.dtsi"
+#include "twl4030_omap3.dtsi"
+
+&twl {
+	vmmc1: regulator-vmmc1 {
+		regulator-always-on;
+	};
+
+	vdd1: regulator-vdd1 {
+		regulator-always-on;
+	};
+
+	vdd2: regulator-vdd2 {
+		regulator-always-on;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <2600000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+};
+
+&i2c3 {
+	clock-frequency = <2600000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
+		gpiom1: gpio@20 {
+			compatible = "mcp,mcp23017";
+			gpio-controller;
+			#gpio-cells = <2>;
+			reg = <0x20>;
+		};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+};
+
+&uart4 {
+	status = "disabled";
+};
+
+&mmc1 {
+	reg = <0x4809c000 0x400>;
+	cd-gpios = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>;
+	cd-inverted;
+	vmmc-supply = <&vmmc1>;
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins &mmc1cd_pins>;
+	cap-sdio-irq;
+	cap-sd-highspeed;
+	cap-mmc-highspeed;
+};
+
+&mmc2 {
+	status = "disabled";
+};
+
+&mmc3 {
+	status = "disabled";
+};
+
+&mcspi2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins>;
+
+	tsc2046@0 {
+		reg = <0>;   /* CS0 */
+		compatible = "ti,tsc2046";
+		interrupt-parent = <&gpio1>;
+		interrupts = <8 0>;   /* boot6 / gpio_8 */
+		spi-max-frequency = <1000000>;
+		pendown-gpio = <&gpio1 8 0>;
+		vcc-supply = <&reg_vcc3>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsc2048_pins>;
+
+		ti,x-min = <300>;
+		ti,x-max = <3000>;
+		ti,y-min = <600>;
+		ti,y-max = <3600>;
+		ti,x-plate-ohms = <80>;
+		ti,pressure-max = <255>;
+		ti,swap-xy;
+
+		linux,wakeup;
+	};
+};
+
+&usbhsehci {
+	phys = <&hsusb1_phy>;
+};
+
+&usbhshost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hsusb1_pins>;
+	num-ports = <2>;
+	port1-mode = "ehci-phy";
+};
+
+&usb_otg_hs {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hsusb_otg_pins>;
+	interface-type = <0>;
+	usb-phy = <&usb2_phy>;
+	phys = <&usb2_phy>;
+	phy-names = "usb2-phy";
+	mode = <3>;
+	power = <50>;
+};
+
+&gpmc {
+	ranges = <0 0 0x30000000 0x1000000>,
+		<7 0 0x15000000 0x01000000>;
+
+	nand@0,0 {
+		reg = <0 0 0x1000000>;
+		nand-bus-width = <16>;
+		ti,nand-ecc-opt = "bch8";
+		/* no elm on omap3 */
+
+		gpmc,mux-add-data = <0>;
+		gpmc,device-nand;
+		gpmc,device-width = <2>;
+		gpmc,wait-pin = <0>;
+		gpmc,wait-monitoring-ns = <0>;
+		gpmc,burst-length= <4>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <100>;
+		gpmc,cs-wr-off-ns = <100>;
+		gpmc,adv-on-ns = <0>;
+		gpmc,adv-rd-off-ns = <100>;
+		gpmc,adv-wr-off-ns = <100>;
+		gpmc,oe-on-ns = <5>;
+		gpmc,oe-off-ns = <75>;
+		gpmc,we-on-ns = <5>;
+		gpmc,we-off-ns = <75>;
+		gpmc,rd-cycle-ns = <100>;
+		gpmc,wr-cycle-ns = <100>;
+		gpmc,access-ns = <60>;
+		gpmc,page-burst-access-ns = <5>;
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-samecsen;
+		gpmc,cycle2cycle-delay-ns = <50>;
+		gpmc,wr-data-mux-bus-ns = <75>;
+		gpmc,wr-access-ns = <155>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "MLO";
+			reg = <0 0x80000>;
+		};
+
+		partition@0x80000 {
+			label = "u-boot";
+			reg = <0x80000 0x1e0000>;
+		};
+
+		partition@0x260000 {
+			label = "u-boot-environment";
+			reg = <0x260000 0x20000>;
+		};
+
+		partition@0x280000 {
+			label = "kernel";
+			reg = <0x280000 0x500000>;
+		};
+
+		partition@0x780000 {
+			label = "filesystem";
+			reg = <0x780000 0xf880000>;
+		};
+	};
+
+	ethernet@7,0 {
+		compatible = "smsc,lan9221", "smsc,lan9115";
+		bank-width = <2>;
+		gpmc,mux-add-data = <2>;
+		gpmc,cs-on-ns = <10>;
+		gpmc,cs-rd-off-ns = <60>;
+		gpmc,cs-wr-off-ns = <60>;
+		gpmc,adv-on-ns = <0>;
+		gpmc,adv-rd-off-ns = <10>;
+		gpmc,adv-wr-off-ns = <10>;
+		gpmc,oe-on-ns = <10>;
+		gpmc,oe-off-ns = <60>;
+		gpmc,we-on-ns = <10>;
+		gpmc,we-off-ns = <60>;
+		gpmc,rd-cycle-ns = <100>;
+		gpmc,wr-cycle-ns = <100>;
+		gpmc,access-ns = <50>;
+		gpmc,page-burst-access-ns = <5>;
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <75>;
+		gpmc,wr-data-mux-bus-ns = <15>;
+		gpmc,wr-access-ns = <75>;
+		gpmc,cycle2cycle-samecsen;
+		gpmc,cycle2cycle-diffcsen;
+		vddvario-supply = <&reg_vcc3>;
+		vdd33a-supply = <&reg_vcc3>;
+		reg-io-width = <4>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <1 0x2>;
+		reg = <7 0 0xff>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lan9221_pins>;
+		phy-mode = "mii";
+	};
+};