@@ -1,3 +1,22 @@
+Freescale i.MX DRM master device
+================================
+
+The freescale i.MX DRM master device is a virtual device needed to list all
+IPU or other display interface nodes that comprise the graphics subsystem.
+
+Required properties:
+- compatible: Should be "fsl,imx-drm"
+- ports: Should contain a list of phandles pointing to display interface ports
+ of IPU devices
+
+example:
+
+imx-drm {
+ compatible = "fsl,imx-drm";
+ ports = <&ipu_di0>;
+};
+
+
Freescale i.MX IPUv3
====================
@@ -7,18 +26,31 @@ Required properties:
datasheet
- interrupts: Should contain sync interrupt and error interrupt,
in this order.
-- #crtc-cells: 1, See below
- resets: phandle pointing to the system reset controller and
reset line index, see reset/fsl,imx-src.txt for details
+Optional properties:
+- port@[0-3]: Port nodes with endpoint definitions as defined in
+ Documentation/devicetree/bindings/media/video-interfaces.txt.
+ Ports 0 and 1 should correspond to CSI0 and CSI1,
+ ports 2 and 3 should correspond to DI0 and DI1, respectively.
example:
ipu: ipu@18000000 {
- #crtc-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
compatible = "fsl,imx53-ipu";
reg = <0x18000000 0x080000000>;
interrupts = <11 10>;
resets = <&src 2>;
+
+ ipu_di0: port@2 {
+ reg = <2>;
+
+ ipu_di0_disp0: endpoint {
+ remote-endpoint = <&display_in>;
+ };
+ };
};
Parallel display support
@@ -26,19 +58,25 @@ Parallel display support
Required properties:
- compatible: Should be "fsl,imx-parallel-display"
-- crtc: the crtc this display is connected to, see below
Optional properties:
- interface_pix_fmt: How this display is connected to the
- crtc. Currently supported types: "rgb24", "rgb565", "bgr666"
+ display interface. Currently supported types: "rgb24", "rgb565", "bgr666"
- edid: verbatim EDID data block describing attached display.
- ddc: phandle describing the i2c bus handling the display data
channel
+- port: A port node with endpoint definitions as defined in
+ Documentation/devicetree/bindings/media/video-interfaces.txt.
example:
display@di0 {
compatible = "fsl,imx-parallel-display";
edid = [edid-data];
- crtc = <&ipu 0>;
interface-pix-fmt = "rgb24";
+
+ port {
+ display_in: endpoint {
+ remote-endpoint = <&ipu_di0_disp0>;
+ };
+ };
};
@@ -50,12 +50,14 @@ have a look at Documentation/devicetree/bindings/video/display-timing.txt.
Required properties:
- reg : should be <0> or <1>
- - crtcs : a list of phandles with index pointing to the IPU display interfaces
- that can be used as video source for this channel.
- fsl,data-mapping : should be "spwg" or "jeida"
This describes how the color bits are laid out in the
serialized LVDS signal.
- fsl,data-width : should be <18> or <24>
+ - port: A port node with endpoint definitions as defined in
+ Documentation/devicetree/bindings/media/video-interfaces.txt.
+ On i.MX6, there should be four ports (port@[0-3]) that correspond
+ to the four LVDS multiplexer inputs.
example:
@@ -77,23 +79,33 @@ ldb: ldb@53fa8008 {
lvds-channel@0 {
reg = <0>;
- crtcs = <&ipu 0>;
fsl,data-mapping = "spwg";
fsl,data-width = <24>;
display-timings {
/* ... */
};
+
+ port {
+ lvds0_in: endpoint {
+ remote-endpoint = <&ipu_di0_lvds0>;
+ };
+ };
};
lvds-channel@1 {
reg = <1>;
- crtcs = <&ipu 1>;
fsl,data-mapping = "spwg";
fsl,data-width = <24>;
display-timings {
/* ... */
};
+
+ port {
+ lvds1_in: endpoint {
+ remote-endpoint = <&ipu_di1_lvds1>;
+ };
+ };
};
};
This patch updates the device tree binding documentation for i.MX IPU/display nodes using the OF graph bindings documented in Documentation/devicetree/bindings/media/video-interfaces.txt. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> --- .../bindings/staging/imx-drm/fsl-imx-drm.txt | 48 +++++++++++++++++++--- .../devicetree/bindings/staging/imx-drm/ldb.txt | 20 +++++++-- 2 files changed, 59 insertions(+), 9 deletions(-)