| Message ID | 1392840157-31072-5-git-send-email-klightspeed@killerwolves.net (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Thu, Feb 20, 2014 at 06:02:37AM +1000, klightspeed@killerwolves.net wrote: > From: "Ben Peddell" <klightspeed@killerwolves.net> > > Add device tree fragments and files to support many of the kirkwood > based Synology NAS devices. This is a modification of > Andrew Lunn's <andrew@lunn.ch> translation of the board setup file > maintained by Ben Peddell <klightspeed@killerwolves.net> > > The Ricoh RS5C372 RTC was used in all 2009 units and some 2010 units. > All other Synology Kirkwood-based DiskStations and RackStations use > the Seiko S35390A RTC. > > Most of the 1-bay and 2-bay units use the GPIOs that are multiplexed > with the built-in SATA interface activity/presence pins on mpp 20-23, > while the 4-bay units use ge01 and a PCIe SATA controller, and put the > software controlled HDD leds on mpp 36-43. > > Most of the 6281 units with HDD power controls use mpp 29 and 31, while > most of the 6282 units with HDD power controls use mpp 30, 34, 44 and 45 > and provide a model ID on mpp 28, 29, 46 and 47. Pre-2012 units and > most 4-bay units didn't have a separate power control for HDD1. These > power controls are presumably to limit startup current from the 12V > brick power supply. > > Instead of using separate dtsi files in a synology directory, this > patch uses a single dtsi file containing all of the modules for > these boards, with all of the modules not common to all boards > disabled. The board dts files then enable the appropriate modules for > their boards. > > Signed-off-by: Ben Peddell <klightspeed@killerwolves.net> > Tested-by: Ben Peddell <klightspeed@killerwolves.net> (ds211j) Since it is based on my code: Signed-off-by: Andrew Lunn <andrew@lunn.ch> Andrew > --- > v2: > Fix gpio's which should be gpo. > Rebase onto v3-14-rc1 > Update RTC nodes with vendor name. > Update SPI flash node with vendor name. > Add a description of the lego > Use ricoy, i.e. the stock ticker > > v3: > Merge Synology dtsi files into single dtsi file > > v4: > Various minor fixes to synology dtsi file > > v7: > Revert ricoh vendor prefix change from v2 > --- > arch/arm/boot/dts/Makefile | 15 + > arch/arm/boot/dts/kirkwood-ds109.dts | 41 ++ > arch/arm/boot/dts/kirkwood-ds110jv10.dts | 41 ++ > arch/arm/boot/dts/kirkwood-ds111.dts | 44 ++ > arch/arm/boot/dts/kirkwood-ds112.dts | 48 ++ > arch/arm/boot/dts/kirkwood-ds209.dts | 44 ++ > arch/arm/boot/dts/kirkwood-ds210.dts | 46 ++ > arch/arm/boot/dts/kirkwood-ds212.dts | 47 ++ > arch/arm/boot/dts/kirkwood-ds212j.dts | 41 ++ > arch/arm/boot/dts/kirkwood-ds409.dts | 48 ++ > arch/arm/boot/dts/kirkwood-ds409slim.dts | 40 ++ > arch/arm/boot/dts/kirkwood-ds411.dts | 52 ++ > arch/arm/boot/dts/kirkwood-ds411j.dts | 48 ++ > arch/arm/boot/dts/kirkwood-ds411slim.dts | 48 ++ > arch/arm/boot/dts/kirkwood-rs212.dts | 48 ++ > arch/arm/boot/dts/kirkwood-rs409.dts | 44 ++ > arch/arm/boot/dts/kirkwood-rs411.dts | 44 ++ > arch/arm/boot/dts/kirkwood-synology.dtsi | 871 +++++++++++++++++++++++++++++++ > 18 files changed, 1610 insertions(+) > create mode 100644 arch/arm/boot/dts/kirkwood-ds109.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds110jv10.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds111.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds112.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds209.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds210.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds212.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds212j.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds409.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds409slim.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds411.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds411j.dts > create mode 100644 arch/arm/boot/dts/kirkwood-ds411slim.dts > create mode 100644 arch/arm/boot/dts/kirkwood-rs212.dts > create mode 100644 arch/arm/boot/dts/kirkwood-rs409.dts > create mode 100644 arch/arm/boot/dts/kirkwood-rs411.dts > create mode 100644 arch/arm/boot/dts/kirkwood-synology.dtsi > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 6d1e43d..e286abc 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -90,6 +90,18 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-cloudbox.dtb \ > kirkwood-dns325.dtb \ > kirkwood-dockstar.dtb \ > kirkwood-dreamplug.dtb \ > + kirkwood-ds109.dtb \ > + kirkwood-ds110jv10.dtb \ > + kirkwood-ds111.dtb \ > + kirkwood-ds209.dtb \ > + kirkwood-ds210.dtb \ > + kirkwood-ds212.dtb \ > + kirkwood-ds212j.dtb \ > + kirkwood-ds409.dtb \ > + kirkwood-ds409slim.dtb \ > + kirkwood-ds411.dtb \ > + kirkwood-ds411j.dtb \ > + kirkwood-ds411slim.dtb \ > kirkwood-goflexnet.dtb \ > kirkwood-guruplug-server-plus.dtb \ > kirkwood-ib62x0.dtb \ > @@ -112,6 +124,9 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-cloudbox.dtb \ > kirkwood-nsa310a.dtb \ > kirkwood-openblocks_a6.dtb \ > kirkwood-openblocks_a7.dtb \ > + kirkwood-rs212.dtb \ > + kirkwood-rs409.dtb \ > + kirkwood-rs411.dtb \ > kirkwood-sheevaplug.dtb \ > kirkwood-sheevaplug-esata.dtb \ > kirkwood-topkick.dtb \ > diff --git a/arch/arm/boot/dts/kirkwood-ds109.dts b/arch/arm/boot/dts/kirkwood-ds109.dts > new file mode 100644 > index 0000000..772092c > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-ds109.dts > @@ -0,0 +1,41 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6281.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology DS109, DS110, DS110jv20"; > + compatible = "synology,ds109", "synology,ds110jv20", > + "synology,ds110", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-150-32-35 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-21-1 { > + status = "okay"; > + }; > +}; > + > +&rs5c372 { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-ds110jv10.dts b/arch/arm/boot/dts/kirkwood-ds110jv10.dts > new file mode 100644 > index 0000000..aabafbe > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-ds110jv10.dts > @@ -0,0 +1,41 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6281.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology DS110j v10 and v30"; > + compatible = "synology,ds110jv10", "synology,ds110jv30", > + "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-150-32-35 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-21-1 { > + status = "okay"; > + }; > +}; > + > +&s35390a { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-ds111.dts b/arch/arm/boot/dts/kirkwood-ds111.dts > new file mode 100644 > index 0000000..16ec7fb > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-ds111.dts > @@ -0,0 +1,44 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6282.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology DS111"; > + compatible = "synology,ds111", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-100-15-35-1 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-21-1 { > + status = "okay"; > + }; > +}; > + > +&s35390a { > + status = "okay"; > +}; > + > +&pcie2 { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-ds112.dts b/arch/arm/boot/dts/kirkwood-ds112.dts > new file mode 100644 > index 0000000..cff1b23 > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-ds112.dts > @@ -0,0 +1,48 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6282.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology DS111"; > + compatible = "synology,ds111", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-100-15-35-1 { > + status = "okay"; > + }; > + > + gpio-leds-21-2 { > + status = "okay"; > + }; > + > + regulators-hdd-30 { > + status = "okay"; > + }; > +}; > + > +&s35390a { > + status = "okay"; > +}; > + > +&pcie2 { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-ds209.dts b/arch/arm/boot/dts/kirkwood-ds209.dts > new file mode 100644 > index 0000000..3304119 > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-ds209.dts > @@ -0,0 +1,44 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6281.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology DS209"; > + compatible = "synology,ds209", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-150-32-35 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-21-2 { > + status = "okay"; > + }; > + > + regulators-hdd-31 { > + status = "okay"; > + }; > +}; > + > +&rs5c372 { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-ds210.dts b/arch/arm/boot/dts/kirkwood-ds210.dts > new file mode 100644 > index 0000000..6052eaa > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-ds210.dts > @@ -0,0 +1,46 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6281.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology DS210 v10, v20, v30, DS211j"; > + compatible = "synology,ds210jv10", "synology,ds210jv20", > + "synology,ds210jv30", "synology,ds211j", > + "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-150-32-35 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-21-2 { > + status = "okay"; > + }; > + > + regulators-hdd-31 { > + status = "okay"; > + }; > +}; > + > +&s35390a { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-ds212.dts b/arch/arm/boot/dts/kirkwood-ds212.dts > new file mode 100644 > index 0000000..7f76cd3 > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-ds212.dts > @@ -0,0 +1,47 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6282.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology DS212, DS212p v10, v20, DS213air v10, DS213 v10"; > + compatible = "synology,ds212", "synology,ds212pv10", > + "synology,ds212pv10", "synology,ds212pv20", > + "synology,ds213airv10", "synology,ds213v10", > + "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-100-15-35-1 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-21-2 { > + status = "okay"; > + }; > +}; > + > +&s35390a { > + status = "okay"; > +}; > + > +&pcie2 { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-ds212j.dts b/arch/arm/boot/dts/kirkwood-ds212j.dts > new file mode 100644 > index 0000000..1f83a00 > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-ds212j.dts > @@ -0,0 +1,41 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6281.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology DS212j v10, v20"; > + compatible = "synology,ds212jv10", "synology,ds212jv20", > + "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-100-32-35 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-21-2 { > + status = "okay"; > + }; > +}; > + > +&s35390a { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-ds409.dts b/arch/arm/boot/dts/kirkwood-ds409.dts > new file mode 100644 > index 0000000..0a573ad > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-ds409.dts > @@ -0,0 +1,48 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6281.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology DS409, DS410j"; > + compatible = "synology,ds409", "synology,ds410j", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-150-15-18 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-36 { > + status = "okay"; > + }; > + > + gpio-leds-alarm-12 { > + status = "okay"; > + }; > +}; > + > +ð1 { > + status = "okay"; > +}; > + > +&rs5c372 { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-ds409slim.dts b/arch/arm/boot/dts/kirkwood-ds409slim.dts > new file mode 100644 > index 0000000..1848a62 > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-ds409slim.dts > @@ -0,0 +1,40 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6281.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology 409slim"; > + compatible = "synology,ds409slim", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-150-32-35 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-20 { > + status = "okay"; > + }; > +}; > + > +&rs5c372 { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-ds411.dts b/arch/arm/boot/dts/kirkwood-ds411.dts > new file mode 100644 > index 0000000..a1737b4 > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-ds411.dts > @@ -0,0 +1,52 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6282.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology DS411, DS413jv10"; > + compatible = "synology,ds411", "synology,ds413jv10", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-100-15-35-1 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-36 { > + status = "okay"; > + }; > + > + regulators-hdd-34 { > + status = "okay"; > + }; > +}; > + > +ð1 { > + status = "okay"; > +}; > + > +&s35390a { > + status = "okay"; > +}; > + > +&pcie2 { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-ds411j.dts b/arch/arm/boot/dts/kirkwood-ds411j.dts > new file mode 100644 > index 0000000..0cde914 > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-ds411j.dts > @@ -0,0 +1,48 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6281.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology DS411j"; > + compatible = "synology,ds411j", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-150-15-18 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-36 { > + status = "okay"; > + }; > + > + gpio-leds-alarm-12 { > + status = "okay"; > + }; > +}; > + > +ð1 { > + status = "okay"; > +}; > + > +&s35390a { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-ds411slim.dts b/arch/arm/boot/dts/kirkwood-ds411slim.dts > new file mode 100644 > index 0000000..aef0cad > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-ds411slim.dts > @@ -0,0 +1,48 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6282.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology DS411slim"; > + compatible = "synology,ds411slim", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-100-15-35-1 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-36 { > + status = "okay"; > + }; > +}; > + > +ð1 { > + status = "okay"; > +}; > + > +&s35390a { > + status = "okay"; > +}; > + > +&pcie2 { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-rs212.dts b/arch/arm/boot/dts/kirkwood-rs212.dts > new file mode 100644 > index 0000000..93ec3d0 > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-rs212.dts > @@ -0,0 +1,48 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6282.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology RS212"; > + compatible = "synology,rs212", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-100-15-35-3 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-38 { > + status = "okay"; > + }; > + > + regulators-hdd-30-2 { > + status = "okay"; > + }; > +}; > + > +&s35390a { > + status = "okay"; > +}; > + > +&pcie2 { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-rs409.dts b/arch/arm/boot/dts/kirkwood-rs409.dts > new file mode 100644 > index 0000000..311df4e > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-rs409.dts > @@ -0,0 +1,44 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6281.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology RS409"; > + compatible = "synology,rs409", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-150-15-18 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-36 { > + status = "okay"; > + }; > +}; > + > +ð1 { > + status = "okay"; > +}; > + > +&rs5c372 { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-rs411.dts b/arch/arm/boot/dts/kirkwood-rs411.dts > new file mode 100644 > index 0000000..f90da85 > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-rs411.dts > @@ -0,0 +1,44 @@ > +/* > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/dts-v1/; > + > +#include "kirkwood.dtsi" > +#include "kirkwood-6282.dtsi" > +#include "kirkwood-synology.dtsi" > + > +/ { > + model = "Synology RS411 RS812"; > + compatible = "synology,rs411", "synology,rs812", "marvell,kirkwood"; > + > + memory { > + device_type = "memory"; > + reg = <0x00000000 0x8000000>; > + }; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + gpio-fan-100-15-35-3 { > + status = "okay"; > + }; > + > + gpio-leds-hdd-36 { > + status = "okay"; > + }; > +}; > + > +ð1 { > + status = "okay"; > +}; > + > +&s35390a { > + status = "okay"; > +}; > diff --git a/arch/arm/boot/dts/kirkwood-synology.dtsi b/arch/arm/boot/dts/kirkwood-synology.dtsi > new file mode 100644 > index 0000000..92b3177 > --- /dev/null > +++ b/arch/arm/boot/dts/kirkwood-synology.dtsi > @@ -0,0 +1,871 @@ > +/* > + * Nodes for Marvell 628x Synology devices > + * > + * Andrew Lunn <andrew@lunn.ch> > + * Ben Peddell <klightspeed@killerwolves.net> > + * > + * This file is licensed under the terms of the GNU General Public > + * License version 2. This program is licensed "as is" without any > + * warranty of any kind, whether express or implied. > + */ > + > +/ { > + mbus { > + pcie-controller { > + status = "okay"; > + > + pcie@1,0 { > + status = "okay"; > + }; > + > + pcie2: pcie@2,0 { > + status = "disabled"; > + }; > + }; > + }; > + > + ocp@f1000000 { > + pinctrl: pinctrl@10000 { > + pmx_alarmled_12: pmx-alarmled-12 { > + marvell,pins = "mpp12"; > + marvell,function = "gpio"; > + }; > + > + pmx_fanctrl_15: pmx-fanctrl-15 { > + marvell,pins = "mpp15"; > + marvell,function = "gpio"; > + }; > + > + pmx_fanctrl_16: pmx-fanctrl-16 { > + marvell,pins = "mpp16"; > + marvell,function = "gpio"; > + }; > + > + pmx_fanctrl_17: pmx-fanctrl-17 { > + marvell,pins = "mpp17"; > + marvell,function = "gpio"; > + }; > + > + pmx_fanalarm_18: pmx-fanalarm-18 { > + marvell,pins = "mpp18"; > + marvell,function = "gpo"; > + }; > + > + pmx_hddled_20: pmx-hddled-20 { > + marvell,pins = "mpp20"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_21: pmx-hddled-21 { > + marvell,pins = "mpp21"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_22: pmx-hddled-22 { > + marvell,pins = "mpp22"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_23: pmx-hddled-23 { > + marvell,pins = "mpp23"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_24: pmx-hddled-24 { > + marvell,pins = "mpp24"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_25: pmx-hddled-25 { > + marvell,pins = "mpp25"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_26: pmx-hddled-26 { > + marvell,pins = "mpp26"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_27: pmx-hddled-27 { > + marvell,pins = "mpp27"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_28: pmx-hddled-28 { > + marvell,pins = "mpp28"; > + marvell,function = "gpio"; > + }; > + > + pmx_hdd1_pwr_29: pmx-hdd1-pwr-29 { > + marvell,pins = "mpp29"; > + marvell,function = "gpio"; > + }; > + > + pmx_hdd1_pwr_30: pmx-hdd-pwr-30 { > + marvell,pins = "mpp30"; > + marvell,function = "gpio"; > + }; > + > + pmx_hdd2_pwr_31: pmx-hdd2-pwr-31 { > + marvell,pins = "mpp31"; > + marvell,function = "gpio"; > + }; > + > + pmx_fanctrl_32: pmx-fanctrl-32 { > + marvell,pins = "mpp32"; > + marvell,function = "gpio"; > + }; > + > + pmx_fanctrl_33: pmx-fanctrl-33 { > + marvell,pins = "mpp33"; > + marvell,function = "gpo"; > + }; > + > + pmx_fanctrl_34: pmx-fanctrl-34 { > + marvell,pins = "mpp34"; > + marvell,function = "gpio"; > + }; > + > + pmx_hdd2_pwr_34: pmx-hdd2-pwr-34 { > + marvell,pins = "mpp34"; > + marvell,function = "gpio"; > + }; > + > + pmx_fanalarm_35: pmx-fanalarm-35 { > + marvell,pins = "mpp35"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_36: pmx-hddled-36 { > + marvell,pins = "mpp36"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_37: pmx-hddled-37 { > + marvell,pins = "mpp37"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_38: pmx-hddled-38 { > + marvell,pins = "mpp38"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_39: pmx-hddled-39 { > + marvell,pins = "mpp39"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_40: pmx-hddled-40 { > + marvell,pins = "mpp40"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_41: pmx-hddled-41 { > + marvell,pins = "mpp41"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_42: pmx-hddled-42 { > + marvell,pins = "mpp42"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_43: pmx-hddled-43 { > + marvell,pins = "mpp43"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_44: pmx-hddled-44 { > + marvell,pins = "mpp44"; > + marvell,function = "gpio"; > + }; > + > + pmx_hddled_45: pmx-hddled-45 { > + marvell,pins = "mpp45"; > + marvell,function = "gpio"; > + }; > + > + pmx_hdd3_pwr_44: pmx-hdd3-pwr-44 { > + marvell,pins = "mpp44"; > + marvell,function = "gpio"; > + }; > + > + pmx_hdd4_pwr_45: pmx-hdd4-pwr-45 { > + marvell,pins = "mpp45"; > + marvell,function = "gpio"; > + }; > + > + pmx_fanalarm_44: pmx-fanalarm-44 { > + marvell,pins = "mpp44"; > + marvell,function = "gpio"; > + }; > + > + pmx_fanalarm_45: pmx-fanalarm-45 { > + marvell,pins = "mpp45"; > + marvell,function = "gpio"; > + }; > + }; > + > + rtc@10300 { > + status = "disabled"; > + }; > + > + spi@10600 { > + status = "okay"; > + pinctrl-0 = <&pmx_spi>; > + pinctrl-names = "default"; > + > + m25p80@0 { > + #address-cells = <1>; > + #size-cells = <1>; > + compatible = "st,m25p80"; > + reg = <0>; > + spi-max-frequency = <20000000>; > + mode = <0>; > + > + partition@00000000 { > + reg = <0x00000000 0x00080000>; > + label = "RedBoot"; > + }; > + > + partition@00080000 { > + reg = <0x00080000 0x00200000>; > + label = "zImage"; > + }; > + > + partition@00280000 { > + reg = <0x00280000 0x00140000>; > + label = "rd.gz"; > + }; > + > + partition@003c0000 { > + reg = <0x003c0000 0x00010000>; > + label = "vendor"; > + }; > + > + partition@003d0000 { > + reg = <0x003d0000 0x00020000>; > + label = "RedBoot config"; > + }; > + > + partition@003f0000 { > + reg = <0x003f0000 0x00010000>; > + label = "FIS directory"; > + }; > + }; > + }; > + > + i2c@11000 { > + status = "okay"; > + clock-frequency = <400000>; > + pinctrl-0 = <&pmx_twsi0>; > + pinctrl-names = "default"; > + > + rs5c372: rs5c372@32 { > + status = "disabled"; > + compatible = "ricoh,rs5c372"; > + reg = <0x32>; > + }; > + > + s35390a: s35390a@30 { > + status = "disabled"; > + compatible = "ssi,s35390a"; > + reg = <0x30>; > + }; > + }; > + > + serial@12000 { > + status = "okay"; > + pinctrl-0 = <&pmx_uart0>; > + pinctrl-names = "default"; > + }; > + > + serial@12100 { > + status = "okay"; > + pinctrl-0 = <&pmx_uart1>; > + pinctrl-names = "default"; > + }; > + > + poweroff@12100 { > + compatible = "synology,power-off"; > + reg = <0x12100 0x100>; > + clocks = <&gate_clk 7>; > + }; > + > + sata@80000 { > + pinctrl-0 = <&pmx_sata0 &pmx_sata1>; > + pinctrl-names = "default"; > + status = "okay"; > + nr-ports = <2>; > + }; > + }; > + > + gpio-fan-150-32-35 { > + status = "disabled"; > + compatible = "gpio-fan"; > + pinctrl-0 = <&pmx_fanctrl_32 &pmx_fanctrl_33 &pmx_fanctrl_34 > + &pmx_fanalarm_35>; > + pinctrl-names = "default"; > + gpios = <&gpio1 0 GPIO_ACTIVE_HIGH > + &gpio1 1 GPIO_ACTIVE_HIGH > + &gpio1 2 GPIO_ACTIVE_HIGH>; > + gpio-fan,speed-map = < 0 0 > + 2200 1 > + 2500 2 > + 3000 4 > + 3300 3 > + 3700 5 > + 3800 6 > + 4200 7 >; > + }; > + > + gpio-fan-150-15-18 { > + status = "disabled"; > + compatible = "gpio-fan"; > + pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17 > + &pmx_fanalarm_18>; > + pinctrl-names = "default"; > + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH > + &gpio0 16 GPIO_ACTIVE_HIGH > + &gpio0 17 GPIO_ACTIVE_HIGH>; > + alarm-gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>; > + gpio-fan,speed-map = < 0 0 > + 2200 1 > + 2500 2 > + 3000 4 > + 3300 3 > + 3700 5 > + 3800 6 > + 4200 7 >; > + }; > + > + gpio-fan-100-32-35 { > + status = "disabled"; > + compatible = "gpio-fan"; > + pinctrl-0 = <&pmx_fanctrl_32 &pmx_fanctrl_33 &pmx_fanctrl_34 > + &pmx_fanalarm_35>; > + pinctrl-names = "default"; > + gpios = <&gpio1 0 GPIO_ACTIVE_HIGH > + &gpio1 1 GPIO_ACTIVE_HIGH > + &gpio1 2 GPIO_ACTIVE_HIGH>; > + alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; > + gpio-fan,speed-map = < 0 0 > + 2500 1 > + 3100 2 > + 3800 3 > + 4600 4 > + 4800 5 > + 4900 6 > + 5000 7 >; > + }; > + > + gpio-fan-100-15-18 { > + status = "disabled"; > + compatible = "gpio-fan"; > + pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17 > + &pmx_fanalarm_18>; > + pinctrl-names = "default"; > + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH > + &gpio0 16 GPIO_ACTIVE_HIGH > + &gpio0 17 GPIO_ACTIVE_HIGH>; > + alarm-gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>; > + gpio-fan,speed-map = < 0 0 > + 2500 1 > + 3100 2 > + 3800 3 > + 4600 4 > + 4800 5 > + 4900 6 > + 5000 7 >; > + }; > + > + gpio-fan-100-15-35-1 { > + status = "disabled"; > + compatible = "gpio-fan"; > + pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17 > + &pmx_fanalarm_35>; > + pinctrl-names = "default"; > + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH > + &gpio0 16 GPIO_ACTIVE_HIGH > + &gpio0 17 GPIO_ACTIVE_HIGH>; > + alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; > + gpio-fan,speed-map = < 0 0 > + 2500 1 > + 3100 2 > + 3800 3 > + 4600 4 > + 4800 5 > + 4900 6 > + 5000 7 >; > + }; > + > + gpio-fan-100-15-35-3 { > + status = "disabled"; > + compatible = "gpio-fan"; > + pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17 > + &pmx_fanalarm_35 &pmx_fanalarm_44 &pmx_fanalarm_45>; > + pinctrl-names = "default"; > + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH > + &gpio0 16 GPIO_ACTIVE_HIGH > + &gpio0 17 GPIO_ACTIVE_HIGH>; > + alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH > + &gpio1 12 GPIO_ACTIVE_HIGH > + &gpio1 13 GPIO_ACTIVE_HIGH>; > + gpio-fan,speed-map = < 0 0 > + 2500 1 > + 3100 2 > + 3800 3 > + 4600 4 > + 4800 5 > + 4900 6 > + 5000 7 >; > + }; > + > + gpio-leds-alarm-12 { > + status = "disabled"; > + compatible = "gpio-leds"; > + pinctrl-0 = <&pmx_alarmled_12>; > + pinctrl-names = "default"; > + > + hdd1-green { > + label = "synology:alarm"; > + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; > + }; > + }; > + > + gpio-leds-hdd-20 { > + status = "disabled"; > + compatible = "gpio-leds"; > + pinctrl-0 = <&pmx_hddled_20 &pmx_hddled_21 &pmx_hddled_22 > + &pmx_hddled_23 &pmx_hddled_24 &pmx_hddled_25 > + &pmx_hddled_26 &pmx_hddled_27>; > + pinctrl-names = "default"; > + > + hdd1-green { > + label = "synology:green:hdd1"; > + gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; > + }; > + > + hdd1-amber { > + label = "synology:amber:hdd1"; > + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; > + }; > + > + hdd2-green { > + label = "synology:green:hdd2"; > + gpios = <&gpio0 22 GPIO_ACTIVE_LOW>; > + }; > + > + hdd2-amber { > + label = "synology:amber:hdd2"; > + gpios = <&gpio0 23 GPIO_ACTIVE_LOW>; > + }; > + > + hdd3-green { > + label = "synology:green:hdd3"; > + gpios = <&gpio0 24 GPIO_ACTIVE_LOW>; > + }; > + > + hdd3-amber { > + label = "synology:amber:hdd3"; > + gpios = <&gpio0 25 GPIO_ACTIVE_LOW>; > + }; > + > + hdd4-green { > + label = "synology:green:hdd4"; > + gpios = <&gpio0 26 GPIO_ACTIVE_LOW>; > + }; > + > + hdd4-amber { > + label = "synology:amber:hdd4"; > + gpios = <&gpio0 27 GPIO_ACTIVE_LOW>; > + }; > + }; > + > + gpio-leds-hdd-21-1 { > + status = "disabled"; > + compatible = "gpio-leds"; > + pinctrl-0 = <&pmx_hddled_21 &pmx_hddled_23>; > + pinctrl-names = "default"; > + > + hdd1-green { > + label = "synology:green:hdd1"; > + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; > + }; > + > + hdd1-amber { > + label = "synology:amber:hdd1"; > + gpios = <&gpio0 23 GPIO_ACTIVE_LOW>; > + }; > + }; > + > + gpio-leds-hdd-21-2 { > + status = "disabled"; > + compatible = "gpio-leds"; > + pinctrl-0 = <&pmx_hddled_21 &pmx_hddled_23 &pmx_hddled_20 &pmx_hddled_22>; > + pinctrl-names = "default"; > + > + hdd1-green { > + label = "synology:green:hdd1"; > + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; > + }; > + > + hdd1-amber { > + label = "synology:amber:hdd1"; > + gpios = <&gpio0 23 GPIO_ACTIVE_LOW>; > + }; > + > + hdd2-green { > + label = "synology:green:hdd2"; > + gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; > + }; > + > + hdd2-amber { > + label = "synology:amber:hdd2"; > + gpios = <&gpio0 22 GPIO_ACTIVE_LOW>; > + }; > + }; > + > + gpio-leds-hdd-36 { > + status = "disabled"; > + compatible = "gpio-leds"; > + pinctrl-0 = <&pmx_hddled_36 &pmx_hddled_37 &pmx_hddled_38 > + &pmx_hddled_39 &pmx_hddled_40 &pmx_hddled_41 > + &pmx_hddled_42 &pmx_hddled_43 &pmx_hddled_44 > + &pmx_hddled_45>; > + pinctrl-names = "default"; > + > + hdd1-green { > + label = "synology:green:hdd1"; > + gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; > + }; > + > + hdd1-amber { > + label = "synology:amber:hdd1"; > + gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; > + }; > + > + hdd2-green { > + label = "synology:green:hdd2"; > + gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; > + }; > + > + hdd2-amber { > + label = "synology:amber:hdd2"; > + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; > + }; > + > + hdd3-green { > + label = "synology:green:hdd3"; > + gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; > + }; > + > + hdd3-amber { > + label = "synology:amber:hdd3"; > + gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; > + }; > + > + hdd4-green { > + label = "synology:green:hdd4"; > + gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; > + }; > + > + hdd4-amber { > + label = "synology:amber:hdd4"; > + gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; > + }; > + > + hdd5-green { > + label = "synology:green:hdd5"; > + gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; > + }; > + > + hdd5-amber { > + label = "synology:amber:hdd5"; > + gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; > + }; > + }; > + > + gpio-leds-hdd-38 { > + status = "disabled"; > + compatible = "gpio-leds"; > + pinctrl-0 = <&pmx_hddled_38 &pmx_hddled_39 &pmx_hddled_36 &pmx_hddled_37>; > + pinctrl-names = "default"; > + > + hdd1-green { > + label = "synology:green:hdd1"; > + gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; > + }; > + > + hdd1-amber { > + label = "synology:amber:hdd1"; > + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; > + }; > + > + hdd2-green { > + label = "synology:green:hdd2"; > + gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; > + }; > + > + hdd2-amber { > + label = "synology:amber:hdd2"; > + gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; > + }; > + }; > + > + regulators-hdd-29 { > + status = "disabled"; > + compatible = "simple-bus"; > + #address-cells = <1>; > + #size-cells = <0>; > + pinctrl-0 = <&pmx_hdd1_pwr_29 &pmx_hdd2_pwr_31>; > + pinctrl-names = "default"; > + > + regulator@1 { > + compatible = "regulator-fixed"; > + reg = <1>; > + regulator-name = "hdd1power"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + regulator-boot-on; > + startup-delay-us = <5000000>; > + gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>; > + }; > + > + regulator@2 { > + compatible = "regulator-fixed"; > + reg = <2>; > + regulator-name = "hdd2power"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + regulator-boot-on; > + startup-delay-us = <5000000>; > + gpio = <&gpio0 31 GPIO_ACTIVE_HIGH>; > + }; > + }; > + > + regulators-hdd-30-1 { > + status = "disabled"; > + compatible = "simple-bus"; > + #address-cells = <1>; > + #size-cells = <0>; > + pinctrl-0 = <&pmx_hdd1_pwr_30>; > + pinctrl-names = "default"; > + > + regulator@1 { > + compatible = "regulator-fixed"; > + reg = <1>; > + regulator-name = "hdd1power"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + regulator-boot-on; > + startup-delay-us = <5000000>; > + gpio = <&gpio0 30 GPIO_ACTIVE_HIGH>; > + }; > + }; > + > + regulators-hdd-30-2 { > + status = "disabled"; > + compatible = "simple-bus"; > + #address-cells = <1>; > + #size-cells = <0>; > + pinctrl-0 = <&pmx_hdd1_pwr_30 &pmx_hdd2_pwr_34>; > + pinctrl-names = "default"; > + > + regulator@1 { > + compatible = "regulator-fixed"; > + reg = <1>; > + regulator-name = "hdd1power"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + regulator-boot-on; > + startup-delay-us = <5000000>; > + gpio = <&gpio0 30 GPIO_ACTIVE_HIGH>; > + }; > + > + regulator@2 { > + compatible = "regulator-fixed"; > + reg = <2>; > + regulator-name = "hdd2power"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + regulator-boot-on; > + startup-delay-us = <5000000>; > + gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>; > + }; > + }; > + > + regulators-hdd-30-4 { > + status = "disabled"; > + compatible = "simple-bus"; > + #address-cells = <1>; > + #size-cells = <0>; > + pinctrl-0 = <&pmx_hdd1_pwr_30 &pmx_hdd2_pwr_34 > + &pmx_hdd3_pwr_44 &pmx_hdd4_pwr_45>; > + pinctrl-names = "default"; > + > + regulator@1 { > + compatible = "regulator-fixed"; > + reg = <1>; > + regulator-name = "hdd1power"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + regulator-boot-on; > + startup-delay-us = <5000000>; > + gpio = <&gpio0 30 GPIO_ACTIVE_HIGH>; > + }; > + > + regulator@2 { > + compatible = "regulator-fixed"; > + reg = <2>; > + regulator-name = "hdd2power"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + regulator-boot-on; > + startup-delay-us = <5000000>; > + gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>; > + }; > + > + regulator@3 { > + compatible = "regulator-fixed"; > + reg = <3>; > + regulator-name = "hdd3power"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + regulator-boot-on; > + startup-delay-us = <5000000>; > + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; > + }; > + > + regulator@4 { > + compatible = "regulator-fixed"; > + reg = <4>; > + regulator-name = "hdd4power"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + regulator-boot-on; > + startup-delay-us = <5000000>; > + gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>; > + }; > + }; > + > + regulators-hdd-31 { > + status = "disabled"; > + compatible = "simple-bus"; > + #address-cells = <1>; > + #size-cells = <0>; > + pinctrl-0 = <&pmx_hdd2_pwr_31>; > + pinctrl-names = "default"; > + > + regulator@1 { > + compatible = "regulator-fixed"; > + reg = <1>; > + regulator-name = "hdd2power"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + regulator-boot-on; > + startup-delay-us = <5000000>; > + gpio = <&gpio0 31 GPIO_ACTIVE_HIGH>; > + }; > + }; > + > + regulators-hdd-34 { > + status = "disabled"; > + compatible = "simple-bus"; > + #address-cells = <1>; > + #size-cells = <0>; > + pinctrl-0 = <&pmx_hdd2_pwr_34 &pmx_hdd3_pwr_44 > + &pmx_hdd4_pwr_45>; > + pinctrl-names = "default"; > + > + regulator@2 { > + compatible = "regulator-fixed"; > + reg = <2>; > + regulator-name = "hdd2power"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + regulator-boot-on; > + startup-delay-us = <5000000>; > + gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>; > + }; > + > + regulator@3 { > + compatible = "regulator-fixed"; > + reg = <3>; > + regulator-name = "hdd3power"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + regulator-boot-on; > + startup-delay-us = <5000000>; > + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; > + }; > + > + regulator@4 { > + compatible = "regulator-fixed"; > + reg = <4>; > + regulator-name = "hdd4power"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + enable-active-high; > + regulator-always-on; > + regulator-boot-on; > + startup-delay-us = <5000000>; > + gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>; > + }; > + }; > +}; > + > +&mdio { > + status = "okay"; > + > + ethphy0: ethernet-phy@0 { > + device_type = "ethernet-phy"; > + reg = <8>; > + }; > + > + ethphy1: ethernet-phy@1 { > + device_type = "ethernet-phy"; > + reg = <9>; > + }; > +}; > + > +ð0 { > + status = "okay"; > + > + ethernet0-port@0 { > + phy-handle = <ðphy0>; > + }; > +}; > + > +ð1 { > + status = "disabled"; > + > + ethernet1-port@0 { > + phy-handle = <ðphy1>; > + }; > +}; > -- > 1.8.3.2 >
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 6d1e43d..e286abc 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -90,6 +90,18 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-cloudbox.dtb \ kirkwood-dns325.dtb \ kirkwood-dockstar.dtb \ kirkwood-dreamplug.dtb \ + kirkwood-ds109.dtb \ + kirkwood-ds110jv10.dtb \ + kirkwood-ds111.dtb \ + kirkwood-ds209.dtb \ + kirkwood-ds210.dtb \ + kirkwood-ds212.dtb \ + kirkwood-ds212j.dtb \ + kirkwood-ds409.dtb \ + kirkwood-ds409slim.dtb \ + kirkwood-ds411.dtb \ + kirkwood-ds411j.dtb \ + kirkwood-ds411slim.dtb \ kirkwood-goflexnet.dtb \ kirkwood-guruplug-server-plus.dtb \ kirkwood-ib62x0.dtb \ @@ -112,6 +124,9 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-cloudbox.dtb \ kirkwood-nsa310a.dtb \ kirkwood-openblocks_a6.dtb \ kirkwood-openblocks_a7.dtb \ + kirkwood-rs212.dtb \ + kirkwood-rs409.dtb \ + kirkwood-rs411.dtb \ kirkwood-sheevaplug.dtb \ kirkwood-sheevaplug-esata.dtb \ kirkwood-topkick.dtb \ diff --git a/arch/arm/boot/dts/kirkwood-ds109.dts b/arch/arm/boot/dts/kirkwood-ds109.dts new file mode 100644 index 0000000..772092c --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds109.dts @@ -0,0 +1,41 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS109, DS110, DS110jv20"; + compatible = "synology,ds109", "synology,ds110jv20", + "synology,ds110", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-150-32-35 { + status = "okay"; + }; + + gpio-leds-hdd-21-1 { + status = "okay"; + }; +}; + +&rs5c372 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds110jv10.dts b/arch/arm/boot/dts/kirkwood-ds110jv10.dts new file mode 100644 index 0000000..aabafbe --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds110jv10.dts @@ -0,0 +1,41 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS110j v10 and v30"; + compatible = "synology,ds110jv10", "synology,ds110jv30", + "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-150-32-35 { + status = "okay"; + }; + + gpio-leds-hdd-21-1 { + status = "okay"; + }; +}; + +&s35390a { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds111.dts b/arch/arm/boot/dts/kirkwood-ds111.dts new file mode 100644 index 0000000..16ec7fb --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds111.dts @@ -0,0 +1,44 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS111"; + compatible = "synology,ds111", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-100-15-35-1 { + status = "okay"; + }; + + gpio-leds-hdd-21-1 { + status = "okay"; + }; +}; + +&s35390a { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds112.dts b/arch/arm/boot/dts/kirkwood-ds112.dts new file mode 100644 index 0000000..cff1b23 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds112.dts @@ -0,0 +1,48 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS111"; + compatible = "synology,ds111", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-100-15-35-1 { + status = "okay"; + }; + + gpio-leds-21-2 { + status = "okay"; + }; + + regulators-hdd-30 { + status = "okay"; + }; +}; + +&s35390a { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds209.dts b/arch/arm/boot/dts/kirkwood-ds209.dts new file mode 100644 index 0000000..3304119 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds209.dts @@ -0,0 +1,44 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS209"; + compatible = "synology,ds209", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-150-32-35 { + status = "okay"; + }; + + gpio-leds-hdd-21-2 { + status = "okay"; + }; + + regulators-hdd-31 { + status = "okay"; + }; +}; + +&rs5c372 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds210.dts b/arch/arm/boot/dts/kirkwood-ds210.dts new file mode 100644 index 0000000..6052eaa --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds210.dts @@ -0,0 +1,46 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS210 v10, v20, v30, DS211j"; + compatible = "synology,ds210jv10", "synology,ds210jv20", + "synology,ds210jv30", "synology,ds211j", + "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-150-32-35 { + status = "okay"; + }; + + gpio-leds-hdd-21-2 { + status = "okay"; + }; + + regulators-hdd-31 { + status = "okay"; + }; +}; + +&s35390a { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds212.dts b/arch/arm/boot/dts/kirkwood-ds212.dts new file mode 100644 index 0000000..7f76cd3 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds212.dts @@ -0,0 +1,47 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS212, DS212p v10, v20, DS213air v10, DS213 v10"; + compatible = "synology,ds212", "synology,ds212pv10", + "synology,ds212pv10", "synology,ds212pv20", + "synology,ds213airv10", "synology,ds213v10", + "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-100-15-35-1 { + status = "okay"; + }; + + gpio-leds-hdd-21-2 { + status = "okay"; + }; +}; + +&s35390a { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds212j.dts b/arch/arm/boot/dts/kirkwood-ds212j.dts new file mode 100644 index 0000000..1f83a00 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds212j.dts @@ -0,0 +1,41 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS212j v10, v20"; + compatible = "synology,ds212jv10", "synology,ds212jv20", + "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-100-32-35 { + status = "okay"; + }; + + gpio-leds-hdd-21-2 { + status = "okay"; + }; +}; + +&s35390a { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds409.dts b/arch/arm/boot/dts/kirkwood-ds409.dts new file mode 100644 index 0000000..0a573ad --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds409.dts @@ -0,0 +1,48 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS409, DS410j"; + compatible = "synology,ds409", "synology,ds410j", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-150-15-18 { + status = "okay"; + }; + + gpio-leds-hdd-36 { + status = "okay"; + }; + + gpio-leds-alarm-12 { + status = "okay"; + }; +}; + +ð1 { + status = "okay"; +}; + +&rs5c372 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds409slim.dts b/arch/arm/boot/dts/kirkwood-ds409slim.dts new file mode 100644 index 0000000..1848a62 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds409slim.dts @@ -0,0 +1,40 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology 409slim"; + compatible = "synology,ds409slim", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-150-32-35 { + status = "okay"; + }; + + gpio-leds-hdd-20 { + status = "okay"; + }; +}; + +&rs5c372 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds411.dts b/arch/arm/boot/dts/kirkwood-ds411.dts new file mode 100644 index 0000000..a1737b4 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds411.dts @@ -0,0 +1,52 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS411, DS413jv10"; + compatible = "synology,ds411", "synology,ds413jv10", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-100-15-35-1 { + status = "okay"; + }; + + gpio-leds-hdd-36 { + status = "okay"; + }; + + regulators-hdd-34 { + status = "okay"; + }; +}; + +ð1 { + status = "okay"; +}; + +&s35390a { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds411j.dts b/arch/arm/boot/dts/kirkwood-ds411j.dts new file mode 100644 index 0000000..0cde914 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds411j.dts @@ -0,0 +1,48 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS411j"; + compatible = "synology,ds411j", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-150-15-18 { + status = "okay"; + }; + + gpio-leds-hdd-36 { + status = "okay"; + }; + + gpio-leds-alarm-12 { + status = "okay"; + }; +}; + +ð1 { + status = "okay"; +}; + +&s35390a { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds411slim.dts b/arch/arm/boot/dts/kirkwood-ds411slim.dts new file mode 100644 index 0000000..aef0cad --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds411slim.dts @@ -0,0 +1,48 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS411slim"; + compatible = "synology,ds411slim", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-100-15-35-1 { + status = "okay"; + }; + + gpio-leds-hdd-36 { + status = "okay"; + }; +}; + +ð1 { + status = "okay"; +}; + +&s35390a { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-rs212.dts b/arch/arm/boot/dts/kirkwood-rs212.dts new file mode 100644 index 0000000..93ec3d0 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-rs212.dts @@ -0,0 +1,48 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology RS212"; + compatible = "synology,rs212", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-100-15-35-3 { + status = "okay"; + }; + + gpio-leds-hdd-38 { + status = "okay"; + }; + + regulators-hdd-30-2 { + status = "okay"; + }; +}; + +&s35390a { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-rs409.dts b/arch/arm/boot/dts/kirkwood-rs409.dts new file mode 100644 index 0000000..311df4e --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-rs409.dts @@ -0,0 +1,44 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology RS409"; + compatible = "synology,rs409", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-150-15-18 { + status = "okay"; + }; + + gpio-leds-hdd-36 { + status = "okay"; + }; +}; + +ð1 { + status = "okay"; +}; + +&rs5c372 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-rs411.dts b/arch/arm/boot/dts/kirkwood-rs411.dts new file mode 100644 index 0000000..f90da85 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-rs411.dts @@ -0,0 +1,44 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology RS411 RS812"; + compatible = "synology,rs411", "synology,rs812", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-100-15-35-3 { + status = "okay"; + }; + + gpio-leds-hdd-36 { + status = "okay"; + }; +}; + +ð1 { + status = "okay"; +}; + +&s35390a { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-synology.dtsi b/arch/arm/boot/dts/kirkwood-synology.dtsi new file mode 100644 index 0000000..92b3177 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-synology.dtsi @@ -0,0 +1,871 @@ +/* + * Nodes for Marvell 628x Synology devices + * + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/ { + mbus { + pcie-controller { + status = "okay"; + + pcie@1,0 { + status = "okay"; + }; + + pcie2: pcie@2,0 { + status = "disabled"; + }; + }; + }; + + ocp@f1000000 { + pinctrl: pinctrl@10000 { + pmx_alarmled_12: pmx-alarmled-12 { + marvell,pins = "mpp12"; + marvell,function = "gpio"; + }; + + pmx_fanctrl_15: pmx-fanctrl-15 { + marvell,pins = "mpp15"; + marvell,function = "gpio"; + }; + + pmx_fanctrl_16: pmx-fanctrl-16 { + marvell,pins = "mpp16"; + marvell,function = "gpio"; + }; + + pmx_fanctrl_17: pmx-fanctrl-17 { + marvell,pins = "mpp17"; + marvell,function = "gpio"; + }; + + pmx_fanalarm_18: pmx-fanalarm-18 { + marvell,pins = "mpp18"; + marvell,function = "gpo"; + }; + + pmx_hddled_20: pmx-hddled-20 { + marvell,pins = "mpp20"; + marvell,function = "gpio"; + }; + + pmx_hddled_21: pmx-hddled-21 { + marvell,pins = "mpp21"; + marvell,function = "gpio"; + }; + + pmx_hddled_22: pmx-hddled-22 { + marvell,pins = "mpp22"; + marvell,function = "gpio"; + }; + + pmx_hddled_23: pmx-hddled-23 { + marvell,pins = "mpp23"; + marvell,function = "gpio"; + }; + + pmx_hddled_24: pmx-hddled-24 { + marvell,pins = "mpp24"; + marvell,function = "gpio"; + }; + + pmx_hddled_25: pmx-hddled-25 { + marvell,pins = "mpp25"; + marvell,function = "gpio"; + }; + + pmx_hddled_26: pmx-hddled-26 { + marvell,pins = "mpp26"; + marvell,function = "gpio"; + }; + + pmx_hddled_27: pmx-hddled-27 { + marvell,pins = "mpp27"; + marvell,function = "gpio"; + }; + + pmx_hddled_28: pmx-hddled-28 { + marvell,pins = "mpp28"; + marvell,function = "gpio"; + }; + + pmx_hdd1_pwr_29: pmx-hdd1-pwr-29 { + marvell,pins = "mpp29"; + marvell,function = "gpio"; + }; + + pmx_hdd1_pwr_30: pmx-hdd-pwr-30 { + marvell,pins = "mpp30"; + marvell,function = "gpio"; + }; + + pmx_hdd2_pwr_31: pmx-hdd2-pwr-31 { + marvell,pins = "mpp31"; + marvell,function = "gpio"; + }; + + pmx_fanctrl_32: pmx-fanctrl-32 { + marvell,pins = "mpp32"; + marvell,function = "gpio"; + }; + + pmx_fanctrl_33: pmx-fanctrl-33 { + marvell,pins = "mpp33"; + marvell,function = "gpo"; + }; + + pmx_fanctrl_34: pmx-fanctrl-34 { + marvell,pins = "mpp34"; + marvell,function = "gpio"; + }; + + pmx_hdd2_pwr_34: pmx-hdd2-pwr-34 { + marvell,pins = "mpp34"; + marvell,function = "gpio"; + }; + + pmx_fanalarm_35: pmx-fanalarm-35 { + marvell,pins = "mpp35"; + marvell,function = "gpio"; + }; + + pmx_hddled_36: pmx-hddled-36 { + marvell,pins = "mpp36"; + marvell,function = "gpio"; + }; + + pmx_hddled_37: pmx-hddled-37 { + marvell,pins = "mpp37"; + marvell,function = "gpio"; + }; + + pmx_hddled_38: pmx-hddled-38 { + marvell,pins = "mpp38"; + marvell,function = "gpio"; + }; + + pmx_hddled_39: pmx-hddled-39 { + marvell,pins = "mpp39"; + marvell,function = "gpio"; + }; + + pmx_hddled_40: pmx-hddled-40 { + marvell,pins = "mpp40"; + marvell,function = "gpio"; + }; + + pmx_hddled_41: pmx-hddled-41 { + marvell,pins = "mpp41"; + marvell,function = "gpio"; + }; + + pmx_hddled_42: pmx-hddled-42 { + marvell,pins = "mpp42"; + marvell,function = "gpio"; + }; + + pmx_hddled_43: pmx-hddled-43 { + marvell,pins = "mpp43"; + marvell,function = "gpio"; + }; + + pmx_hddled_44: pmx-hddled-44 { + marvell,pins = "mpp44"; + marvell,function = "gpio"; + }; + + pmx_hddled_45: pmx-hddled-45 { + marvell,pins = "mpp45"; + marvell,function = "gpio"; + }; + + pmx_hdd3_pwr_44: pmx-hdd3-pwr-44 { + marvell,pins = "mpp44"; + marvell,function = "gpio"; + }; + + pmx_hdd4_pwr_45: pmx-hdd4-pwr-45 { + marvell,pins = "mpp45"; + marvell,function = "gpio"; + }; + + pmx_fanalarm_44: pmx-fanalarm-44 { + marvell,pins = "mpp44"; + marvell,function = "gpio"; + }; + + pmx_fanalarm_45: pmx-fanalarm-45 { + marvell,pins = "mpp45"; + marvell,function = "gpio"; + }; + }; + + rtc@10300 { + status = "disabled"; + }; + + spi@10600 { + status = "okay"; + pinctrl-0 = <&pmx_spi>; + pinctrl-names = "default"; + + m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p80"; + reg = <0>; + spi-max-frequency = <20000000>; + mode = <0>; + + partition@00000000 { + reg = <0x00000000 0x00080000>; + label = "RedBoot"; + }; + + partition@00080000 { + reg = <0x00080000 0x00200000>; + label = "zImage"; + }; + + partition@00280000 { + reg = <0x00280000 0x00140000>; + label = "rd.gz"; + }; + + partition@003c0000 { + reg = <0x003c0000 0x00010000>; + label = "vendor"; + }; + + partition@003d0000 { + reg = <0x003d0000 0x00020000>; + label = "RedBoot config"; + }; + + partition@003f0000 { + reg = <0x003f0000 0x00010000>; + label = "FIS directory"; + }; + }; + }; + + i2c@11000 { + status = "okay"; + clock-frequency = <400000>; + pinctrl-0 = <&pmx_twsi0>; + pinctrl-names = "default"; + + rs5c372: rs5c372@32 { + status = "disabled"; + compatible = "ricoh,rs5c372"; + reg = <0x32>; + }; + + s35390a: s35390a@30 { + status = "disabled"; + compatible = "ssi,s35390a"; + reg = <0x30>; + }; + }; + + serial@12000 { + status = "okay"; + pinctrl-0 = <&pmx_uart0>; + pinctrl-names = "default"; + }; + + serial@12100 { + status = "okay"; + pinctrl-0 = <&pmx_uart1>; + pinctrl-names = "default"; + }; + + poweroff@12100 { + compatible = "synology,power-off"; + reg = <0x12100 0x100>; + clocks = <&gate_clk 7>; + }; + + sata@80000 { + pinctrl-0 = <&pmx_sata0 &pmx_sata1>; + pinctrl-names = "default"; + status = "okay"; + nr-ports = <2>; + }; + }; + + gpio-fan-150-32-35 { + status = "disabled"; + compatible = "gpio-fan"; + pinctrl-0 = <&pmx_fanctrl_32 &pmx_fanctrl_33 &pmx_fanctrl_34 + &pmx_fanalarm_35>; + pinctrl-names = "default"; + gpios = <&gpio1 0 GPIO_ACTIVE_HIGH + &gpio1 1 GPIO_ACTIVE_HIGH + &gpio1 2 GPIO_ACTIVE_HIGH>; + gpio-fan,speed-map = < 0 0 + 2200 1 + 2500 2 + 3000 4 + 3300 3 + 3700 5 + 3800 6 + 4200 7 >; + }; + + gpio-fan-150-15-18 { + status = "disabled"; + compatible = "gpio-fan"; + pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17 + &pmx_fanalarm_18>; + pinctrl-names = "default"; + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH + &gpio0 16 GPIO_ACTIVE_HIGH + &gpio0 17 GPIO_ACTIVE_HIGH>; + alarm-gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>; + gpio-fan,speed-map = < 0 0 + 2200 1 + 2500 2 + 3000 4 + 3300 3 + 3700 5 + 3800 6 + 4200 7 >; + }; + + gpio-fan-100-32-35 { + status = "disabled"; + compatible = "gpio-fan"; + pinctrl-0 = <&pmx_fanctrl_32 &pmx_fanctrl_33 &pmx_fanctrl_34 + &pmx_fanalarm_35>; + pinctrl-names = "default"; + gpios = <&gpio1 0 GPIO_ACTIVE_HIGH + &gpio1 1 GPIO_ACTIVE_HIGH + &gpio1 2 GPIO_ACTIVE_HIGH>; + alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; + gpio-fan,speed-map = < 0 0 + 2500 1 + 3100 2 + 3800 3 + 4600 4 + 4800 5 + 4900 6 + 5000 7 >; + }; + + gpio-fan-100-15-18 { + status = "disabled"; + compatible = "gpio-fan"; + pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17 + &pmx_fanalarm_18>; + pinctrl-names = "default"; + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH + &gpio0 16 GPIO_ACTIVE_HIGH + &gpio0 17 GPIO_ACTIVE_HIGH>; + alarm-gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>; + gpio-fan,speed-map = < 0 0 + 2500 1 + 3100 2 + 3800 3 + 4600 4 + 4800 5 + 4900 6 + 5000 7 >; + }; + + gpio-fan-100-15-35-1 { + status = "disabled"; + compatible = "gpio-fan"; + pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17 + &pmx_fanalarm_35>; + pinctrl-names = "default"; + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH + &gpio0 16 GPIO_ACTIVE_HIGH + &gpio0 17 GPIO_ACTIVE_HIGH>; + alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; + gpio-fan,speed-map = < 0 0 + 2500 1 + 3100 2 + 3800 3 + 4600 4 + 4800 5 + 4900 6 + 5000 7 >; + }; + + gpio-fan-100-15-35-3 { + status = "disabled"; + compatible = "gpio-fan"; + pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17 + &pmx_fanalarm_35 &pmx_fanalarm_44 &pmx_fanalarm_45>; + pinctrl-names = "default"; + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH + &gpio0 16 GPIO_ACTIVE_HIGH + &gpio0 17 GPIO_ACTIVE_HIGH>; + alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH + &gpio1 12 GPIO_ACTIVE_HIGH + &gpio1 13 GPIO_ACTIVE_HIGH>; + gpio-fan,speed-map = < 0 0 + 2500 1 + 3100 2 + 3800 3 + 4600 4 + 4800 5 + 4900 6 + 5000 7 >; + }; + + gpio-leds-alarm-12 { + status = "disabled"; + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_alarmled_12>; + pinctrl-names = "default"; + + hdd1-green { + label = "synology:alarm"; + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds-hdd-20 { + status = "disabled"; + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_hddled_20 &pmx_hddled_21 &pmx_hddled_22 + &pmx_hddled_23 &pmx_hddled_24 &pmx_hddled_25 + &pmx_hddled_26 &pmx_hddled_27>; + pinctrl-names = "default"; + + hdd1-green { + label = "synology:green:hdd1"; + gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; + }; + + hdd1-amber { + label = "synology:amber:hdd1"; + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; + }; + + hdd2-green { + label = "synology:green:hdd2"; + gpios = <&gpio0 22 GPIO_ACTIVE_LOW>; + }; + + hdd2-amber { + label = "synology:amber:hdd2"; + gpios = <&gpio0 23 GPIO_ACTIVE_LOW>; + }; + + hdd3-green { + label = "synology:green:hdd3"; + gpios = <&gpio0 24 GPIO_ACTIVE_LOW>; + }; + + hdd3-amber { + label = "synology:amber:hdd3"; + gpios = <&gpio0 25 GPIO_ACTIVE_LOW>; + }; + + hdd4-green { + label = "synology:green:hdd4"; + gpios = <&gpio0 26 GPIO_ACTIVE_LOW>; + }; + + hdd4-amber { + label = "synology:amber:hdd4"; + gpios = <&gpio0 27 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds-hdd-21-1 { + status = "disabled"; + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_hddled_21 &pmx_hddled_23>; + pinctrl-names = "default"; + + hdd1-green { + label = "synology:green:hdd1"; + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; + }; + + hdd1-amber { + label = "synology:amber:hdd1"; + gpios = <&gpio0 23 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds-hdd-21-2 { + status = "disabled"; + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_hddled_21 &pmx_hddled_23 &pmx_hddled_20 &pmx_hddled_22>; + pinctrl-names = "default"; + + hdd1-green { + label = "synology:green:hdd1"; + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; + }; + + hdd1-amber { + label = "synology:amber:hdd1"; + gpios = <&gpio0 23 GPIO_ACTIVE_LOW>; + }; + + hdd2-green { + label = "synology:green:hdd2"; + gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; + }; + + hdd2-amber { + label = "synology:amber:hdd2"; + gpios = <&gpio0 22 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds-hdd-36 { + status = "disabled"; + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_hddled_36 &pmx_hddled_37 &pmx_hddled_38 + &pmx_hddled_39 &pmx_hddled_40 &pmx_hddled_41 + &pmx_hddled_42 &pmx_hddled_43 &pmx_hddled_44 + &pmx_hddled_45>; + pinctrl-names = "default"; + + hdd1-green { + label = "synology:green:hdd1"; + gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; + }; + + hdd1-amber { + label = "synology:amber:hdd1"; + gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; + }; + + hdd2-green { + label = "synology:green:hdd2"; + gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + }; + + hdd2-amber { + label = "synology:amber:hdd2"; + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; + }; + + hdd3-green { + label = "synology:green:hdd3"; + gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; + }; + + hdd3-amber { + label = "synology:amber:hdd3"; + gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; + }; + + hdd4-green { + label = "synology:green:hdd4"; + gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; + }; + + hdd4-amber { + label = "synology:amber:hdd4"; + gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; + }; + + hdd5-green { + label = "synology:green:hdd5"; + gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; + }; + + hdd5-amber { + label = "synology:amber:hdd5"; + gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds-hdd-38 { + status = "disabled"; + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_hddled_38 &pmx_hddled_39 &pmx_hddled_36 &pmx_hddled_37>; + pinctrl-names = "default"; + + hdd1-green { + label = "synology:green:hdd1"; + gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + }; + + hdd1-amber { + label = "synology:amber:hdd1"; + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; + }; + + hdd2-green { + label = "synology:green:hdd2"; + gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; + }; + + hdd2-amber { + label = "synology:amber:hdd2"; + gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; + }; + }; + + regulators-hdd-29 { + status = "disabled"; + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_hdd1_pwr_29 &pmx_hdd2_pwr_31>; + pinctrl-names = "default"; + + regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "hdd1power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>; + }; + + regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "hdd2power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio0 31 GPIO_ACTIVE_HIGH>; + }; + }; + + regulators-hdd-30-1 { + status = "disabled"; + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_hdd1_pwr_30>; + pinctrl-names = "default"; + + regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "hdd1power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio0 30 GPIO_ACTIVE_HIGH>; + }; + }; + + regulators-hdd-30-2 { + status = "disabled"; + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_hdd1_pwr_30 &pmx_hdd2_pwr_34>; + pinctrl-names = "default"; + + regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "hdd1power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio0 30 GPIO_ACTIVE_HIGH>; + }; + + regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "hdd2power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>; + }; + }; + + regulators-hdd-30-4 { + status = "disabled"; + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_hdd1_pwr_30 &pmx_hdd2_pwr_34 + &pmx_hdd3_pwr_44 &pmx_hdd4_pwr_45>; + pinctrl-names = "default"; + + regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "hdd1power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio0 30 GPIO_ACTIVE_HIGH>; + }; + + regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "hdd2power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>; + }; + + regulator@3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "hdd3power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; + }; + + regulator@4 { + compatible = "regulator-fixed"; + reg = <4>; + regulator-name = "hdd4power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>; + }; + }; + + regulators-hdd-31 { + status = "disabled"; + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_hdd2_pwr_31>; + pinctrl-names = "default"; + + regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "hdd2power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio0 31 GPIO_ACTIVE_HIGH>; + }; + }; + + regulators-hdd-34 { + status = "disabled"; + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_hdd2_pwr_34 &pmx_hdd3_pwr_44 + &pmx_hdd4_pwr_45>; + pinctrl-names = "default"; + + regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "hdd2power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>; + }; + + regulator@3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "hdd3power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; + }; + + regulator@4 { + compatible = "regulator-fixed"; + reg = <4>; + regulator-name = "hdd4power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&mdio { + status = "okay"; + + ethphy0: ethernet-phy@0 { + device_type = "ethernet-phy"; + reg = <8>; + }; + + ethphy1: ethernet-phy@1 { + device_type = "ethernet-phy"; + reg = <9>; + }; +}; + +ð0 { + status = "okay"; + + ethernet0-port@0 { + phy-handle = <ðphy0>; + }; +}; + +ð1 { + status = "disabled"; + + ethernet1-port@0 { + phy-handle = <ðphy1>; + }; +};