new file mode 100644
@@ -0,0 +1,210 @@
+* Device tree bindings for Texas instruments AEMIF controller
+
+The Async External Memory Interface (EMIF16/AEMIF) controller is intended to
+provide a glue-less interface to a variety of asynchronous memory devices like
+ASRA M, NOR and NAND memory. A total of 256M bytes of any of these memories
+can be accessed at any given time via four chip selects with 64M byte access
+per chip select. Synchronous memories such as DDR1 SD RAM, SDR SDRAM
+and Mobile SDR are not supported.
+
+Documentation:
+Davinci DM646x - http://www.ti.com/lit/ug/sprueq7c/sprueq7c.pdf
+OMAP-L138 (DA850) - http://www.ti.com/lit/ug/spruh77a/spruh77a.pdf
+Kestone - http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf
+
+Required properties:
+
+- compatible: "ti,davinci-aemif"
+ "ti,keystone-aemif"
+ "ti,da850-aemif"
+
+- reg: contains offset/length value for AEMIF control registers
+ space.
+
+- #address-cells: Must be 2. The partition number has to be encoded in the
+ first address cell and it may accept values 0..N-1
+ (N - total number of partitions). It's recommended to
+ assign N-1 number for the control partition. The second
+ cell is the offset into the partition.
+
+- #size-cells: Must be set to 1.
+
+- ranges: Contains memory regions. There are two types of
+ ranges/partitions:
+ - CS-specific partition/range. If continuous, must be
+ set up to reflect the memory layout for 4 chipselects,
+ if not then additional range/partition can be added and
+ child device can select the proper one.
+ - control partition which is common for all CS
+ interfaces.
+
+- clocks: the clock feeding the controller clock. Required only
+ if clock tree data present in device tree.
+ See clock-bindings.txt
+
+- clock-names: clock name. It has to be "aemif". Required only if clock
+ tree data present in device tree, in another case don't
+ use it.
+ See clock-bindings.txt
+
+- clock-ranges: Empty property indicating that child nodes can inherit
+ named clocks. Required only if clock tree data present
+ in device tree.
+ See clock-bindings.txt
+
+
+Child chip-select (cs) nodes contain the memory devices nodes connected to
+such as NOR (e.g. cfi-flash) and NAND (ti,davinci-nand, see davinci-nand.txt).
+There might be board specific devices like FPGAs.
+
+Required child cs node properties:
+
+- #address-cells: Must be 2.
+
+- #size-cells: Must be 1.
+
+- ranges: Empty property indicating that child nodes can inherit
+ memory layout.
+
+- clock-ranges: Empty property indicating that child nodes can inherit
+ named clocks. Required only if clock tree data present
+ in device tree.
+
+- ti,cs-chipselect: number of chipselect. Indicates on the aemif driver
+ which chipselect is used for accessing the memory. For
+ compatibles "ti,davinci-aemif" and "ti,keystone-aemif"
+ it can be in range [0-3]. For compatible
+ "ti,da850-aemif" range is [2-5].
+
+Optional child cs node properties:
+
+- ti,cs-bus-width: width of the asynchronous device's data bus
+ 8 or 16 if not preset 8
+
+- ti,cs-select-strobe-mode: enable/disable select strobe mode
+ In select strobe mode chip select behaves as
+ the strobe and is active only during the strobe
+ period. If present then enable.
+
+- ti,cs-extended-wait-mode: enable/disable extended wait mode
+ if set, the controller monitors the EMIFWAIT pin
+ mapped to that chip select to determine if the
+ device wants to extend the strobe period. If
+ present then enable.
+
+- ti,cs-min-turnaround-ns: minimum turn around time, ns
+ Time between the end of one asynchronous memory
+ access and the start of another asynchronous
+ memory access. This delay is not incurred
+ between a read followed by read or a write
+ followed by a write to same chip select.
+
+- ti,cs-read-setup-ns: read setup width, ns
+ Time between the beginning of a memory cycle
+ and the activation of read strobe.
+ Minimum value is 1 (0 treated as 1).
+
+- ti,cs-read-strobe-ns: read strobe width, ns
+ Time between the activation and deactivation of
+ the read strobe.
+ Minimum value is 1 (0 treated as 1).
+
+- ti,cs-read-hold-ns: read hold width, ns
+ Time between the deactivation of the read
+ strobe and the end of the cycle (which may be
+ either an address change or the deactivation of
+ the chip select signal.
+ Minimum value is 1 (0 treated as 1).
+
+- ti,cs-write-setup-ns: write setup width, ns
+ Time between the beginning of a memory cycle
+ and the activation of write strobe.
+ Minimum value is 1 (0 treated as 1).
+
+- ti,cs-write-strobe-ns: write strobe width, ns
+ Time between the activation and deactivation of
+ the write strobe.
+ Minimum value is 1 (0 treated as 1).
+
+- ti,cs-write-hold-ns: write hold width, ns
+ Time between the deactivation of the write
+ strobe and the end of the cycle (which may be
+ either an address change or the deactivation of
+ the chip select signal.
+ Minimum value is 1 (0 treated as 1).
+
+If any of the above parameters are absent, current parameter value will be taken
+from the corresponding HW reg.
+
+Example for aemif, davinci nand and nor flash chip select shown below.
+
+memory-controller@21000A00 {
+ compatible = "ti,davinci-aemif";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ clocks = <&clkaemif 0>;
+ clock-names = "aemif";
+ clock-ranges;
+ reg = <0x21000A00 0x00000100>;
+ ranges = <0 0 0x70000000 0x10000000
+ 1 0 0x21000A00 0x00000100>;
+ /*
+ * Partition0: CS-specific memory range which is
+ * implemented as continuous physical memory region
+ * Partition1: control memory range
+ */
+
+ nand:cs2 {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ clock-ranges;
+ ranges;
+
+ ti,cs-chipselect = <2>;
+ /* all timings in nanoseconds */
+ ti,cs-min-turnaround-ns = <0>;
+ ti,cs-read-hold-ns = <7>;
+ ti,cs-read-strobe-ns = <42>;
+ ti,cs-read-setup-ns = <14>;
+ ti,cs-write-hold-ns = <7>;
+ ti,cs-write-strobe-ns = <42>;
+ ti,cs-write-setup-ns = <14>;
+
+ nand@0,0x8000000 {
+ compatible = "ti,davinci-nand";
+ reg = <0 0x8000000 0x4000000
+ 1 0x0000000 0x0000100>;
+ /*
+ * Partition0, offset 0x8000000, size 0x4000000
+ * Partition1, offset 0x0000000, size 0x0000100
+ */
+
+ .. see davinci-nand.txt
+ };
+ };
+
+ nor:cs0 {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ clock-ranges;
+ ranges;
+
+ ti,cs-chipselect = <0>;
+ /* all timings in nanoseconds */
+ ti,cs-min-turnaround-ns = <0>;
+ ti,cs-read-hold-ns = <8>;
+ ti,cs-read-strobe-ns = <40>;
+ ti,cs-read-setup-ns = <14>;
+ ti,cs-write-hold-ns = <7>;
+ ti,cs-write-strobe-ns = <40>;
+ ti,cs-write-setup-ns = <14>;
+ ti,cs-bus-width = <16>;
+
+ flash@0,0x0000000 {
+ compatible = "cfi-flash";
+ reg = <0 0x0000000 0x4000000>;
+
+ ...
+ };
+ };
+};