Message ID | 1393441943-1689-1-git-send-email-sboyd@codeaurora.org (mailing list archive) |
---|---|
State | New, archived |
Headers | show |
On Wed, Feb 26, 2014 at 11:12 AM, Stephen Boyd <sboyd@codeaurora.org> wrote: > The compatible string doesn't have an x in it. Fix it. Also > remove the "qcom" prefix from pins and functions as this binding > uses the generic pinctrl bindings for the pins and functions. > > Cc: Bjorn Andersson <bjorn.andersson@sonymobile.com> > Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Thanks Stephen, this looks good. Sorry for missing this before. Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
On Thu, Feb 27, 2014 at 3:12 AM, Stephen Boyd <sboyd@codeaurora.org> wrote: > The compatible string doesn't have an x in it. Fix it. Also > remove the "qcom" prefix from pins and functions as this binding > uses the generic pinctrl bindings for the pins and functions. > > Cc: Bjorn Andersson <bjorn.andersson@sonymobile.com> > Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Thanks Stephen, patch applied with Björn's ACK. Yours, Linus Walleij
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt index 4c352be5dd61..9fb89e3f61ea 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt @@ -1,7 +1,7 @@ Qualcomm MSM8974 TLMM block Required properties: -- compatible: "qcom,msm8x74-pinctrl" +- compatible: "qcom,msm8974-pinctrl" - reg: Should be the base address and length of the TLMM block. - interrupts: Should be the parent IRQ of the TLMM block. - interrupt-controller: Marks the device node as an interrupt controller. @@ -42,14 +42,14 @@ Non-empty subnodes must specify the 'pins' property. Note that not all properties are valid for all pins. -Valid values for qcom,pins are: +Valid values for pins are: gpio0-gpio145 Supports mux, bias and drive-strength sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data Supports bias and drive-strength -Valid values for qcom,function are: +Valid values for function are: blsp_i2c2, blsp_i2c6, blsp_i2c11, blsp_spi1, blsp_uart2, blsp_uart8, slimbus (Note that this is not yet the complete list of functions) @@ -73,18 +73,18 @@ Example: uart2_default: uart2_default { mux { - qcom,pins = "gpio4", "gpio5"; - qcom,function = "blsp_uart2"; + pins = "gpio4", "gpio5"; + function = "blsp_uart2"; }; tx { - qcom,pins = "gpio4"; + pins = "gpio4"; drive-strength = <4>; bias-disable; }; rx { - qcom,pins = "gpio5"; + pins = "gpio5"; drive-strength = <2>; bias-pull-up; };
The compatible string doesn't have an x in it. Fix it. Also remove the "qcom" prefix from pins and functions as this binding uses the generic pinctrl bindings for the pins and functions. Cc: Bjorn Andersson <bjorn.andersson@sonymobile.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> --- .../devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.txt | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-)