new file mode 100644
@@ -0,0 +1,22 @@
+SiI9234 Mobile HD Link Transmitter
+
+Required properties:
+- compatible : "sil,sii9234".
+- reg : I2C address for TPI interface, use 0x39
+- vcc-supply : regulator that supplies the chip
+- gpio-reset : GPIO connected to RESET_N pin
+- gpio-int : GPIO connected to INT pin
+
+Optional properties:
+- extcon : phandle to extcon that wakes up the chip
+
+Additional compatible properties are also allowed.
+
+Example:
+ sii9234@39 {
+ compatible = "sil,sii9234";
+ reg = <0x39>;
+ vcc-supply = <&vsil>;
+ gpio-reset = <&gpf3 4 0>;
+ gpio-int = <&gpf3 5 0>;
+ };
@@ -515,6 +515,14 @@ config SRAM
the genalloc API. It is supposed to be used for small on-chip SRAM
areas found on many SoCs.
+config SII9234
+ tristate "Silicon Image SII9234 Driver"
+ depends on I2C
+ help
+ Say Y here if you want support for the MHL interface.
+ It is an I2C driver, that detects connection of MHL bridge
+ and starts encapsulation of HDMI signal.
+
source "drivers/misc/c2port/Kconfig"
source "drivers/misc/eeprom/Kconfig"
source "drivers/misc/cb710/Kconfig"
@@ -55,3 +55,4 @@ obj-$(CONFIG_SRAM) += sram.o
obj-y += mic/
obj-$(CONFIG_GENWQE) += genwqe/
obj-$(CONFIG_ECHO) += echo/
+obj-$(CONFIG_SII9234) += sii9234.o
new file mode 100644
@@ -0,0 +1,1081 @@
+/*
+ * Copyright (C) 2014 Samsung Electronics
+ *
+ * Author: Tomasz Stanislawski <t.stanislaws@samsung.com>
+ *
+ * Based on sii9234 driver created by:
+ * Adam Hampson <ahampson@sta.samsung.com>
+ * Erik Gilling <konkers@android.com>
+ * Shankar Bandal <shankar.b@samsung.com>
+ * Dharam Kumar <dharam.kr@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/wait.h>
+#include <linux/file.h>
+#include <linux/uaccess.h>
+#include <linux/proc_fs.h>
+#include <linux/extcon.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+#include <linux/extcon.h>
+#include <linux/regulator/machine.h>
+
+/* MHL Tx registers and bits */
+#define MHL_TX_SRST 0x05
+#define MHL_TX_SYSSTAT_REG 0x09
+#define RSEN_STATUS (1<<2)
+#define MHL_TX_INTR1_REG 0x71
+#define HPD_CHANGE_INT (1<<6)
+#define RSEN_CHANGE_INT (1<<5)
+#define MHL_TX_INTR4_REG 0x74
+#define RGND_READY_INT (1<<6)
+#define VBUS_LOW_INT (1<<5)
+#define CBUS_LKOUT_INT (1<<4)
+#define MHL_DISC_FAIL_INT (1<<3)
+#define MHL_EST_INT (1<<2)
+#define MHL_TX_INTR1_ENABLE_REG 0x75
+#define HPD_CHANGE_INT_MASK (1<<6)
+#define RSEN_CHANGE_INT_MASK (1<<5)
+#define MHL_TX_INTR4_ENABLE_REG 0x78
+#define RGND_READY_MASK (1<<6)
+#define CBUS_LKOUT_MASK (1<<4)
+#define MHL_DISC_FAIL_MASK (1<<3)
+#define MHL_EST_MASK (1<<2)
+#define MHL_TX_INT_CTRL_REG 0x79
+#define MHL_TX_TMDS_CCTRL 0x80
+#define MHL_TX_DISC_CTRL1_REG 0x90
+#define MHL_TX_DISC_CTRL2_REG 0x91
+#define SKIP_GND (1<<6)
+#define ATT_THRESH_SHIFT 0x04
+#define ATT_THRESH_MASK (0x03 << ATT_THRESH_SHIFT)
+#define USB_D_OEN (1<<3)
+#define DEGLITCH_TIME_MASK 0x07
+#define DEGLITCH_TIME_2MS 0
+#define DEGLITCH_TIME_4MS 1
+#define DEGLITCH_TIME_8MS 2
+#define DEGLITCH_TIME_16MS 3
+#define DEGLITCH_TIME_40MS 4
+#define DEGLITCH_TIME_50MS 5
+#define DEGLITCH_TIME_60MS 6
+#define DEGLITCH_TIME_128MS 7
+#define MHL_TX_DISC_CTRL3_REG 0x92
+#define MHL_TX_DISC_CTRL4_REG 0x93
+#define MHL_TX_DISC_CTRL5_REG 0x94
+#define MHL_TX_DISC_CTRL6_REG 0x95
+#define USB_D_OVR (1<<7)
+#define USB_ID_OVR (1<<6)
+#define DVRFLT_SEL (1<<5)
+#define BLOCK_RGND_INT (1<<4)
+#define SKIP_DEG (1<<3)
+#define CI2CA_POL (1<<2)
+#define CI2CA_WKUP (1<<1)
+#define SINGLE_ATT (1<<0)
+#define MHL_TX_DISC_CTRL7_REG 0x96
+#define USB_D_ODN (1<<5)
+#define VBUS_CHECK (1<<2)
+#define RGND_INTP_MASK 0x03
+#define RGND_INTP_OPEN 0
+#define RGND_INTP_2K 1
+#define RGND_INTP_1K 2
+#define RGND_INTP_SHORT 3
+#define MHL_TX_DISC_CTRL8_REG 0x97
+#define MHL_TX_STAT2_REG 0x99
+#define MHL_TX_MHLTX_CTL1_REG 0xA0
+#define MHL_TX_MHLTX_CTL2_REG 0xA1
+#define MHL_TX_MHLTX_CTL4_REG 0xA3
+#define MHL_TX_MHLTX_CTL6_REG 0xA5
+#define MHL_TX_MHLTX_CTL7_REG 0xA6
+
+/* HDMI registers */
+#define HDMI_RX_TMDS0_CCTRL1_REG 0x10
+#define HDMI_RX_TMDS_CLK_EN_REG 0x11
+#define HDMI_RX_TMDS_CH_EN_REG 0x12
+#define HDMI_RX_PLL_CALREFSEL_REG 0x17
+#define HDMI_RX_PLL_VCOCAL_REG 0x1A
+#define HDMI_RX_EQ_DATA0_REG 0x22
+#define HDMI_RX_EQ_DATA1_REG 0x23
+#define HDMI_RX_EQ_DATA2_REG 0x24
+#define HDMI_RX_EQ_DATA3_REG 0x25
+#define HDMI_RX_EQ_DATA4_REG 0x26
+#define HDMI_RX_TMDS_ZONE_CTRL_REG 0x4C
+#define HDMI_RX_TMDS_MODE_CTRL_REG 0x4D
+
+/* CBUS registers */
+#define CBUS_INT_STATUS_1_REG 0x08
+#define CBUS_INTR1_ENABLE_REG 0x09
+#define CBUS_MSC_REQ_ABORT_REASON_REG 0x0D
+#define SET_HPD_DOWNSTREAM (1<<6)
+#define CBUS_INT_STATUS_2_REG 0x1E
+#define CBUS_INTR2_ENABLE_REG 0x1F
+#define CBUS_LINK_CONTROL_2_REG 0x31
+#define CBUS_DEVCAP_DEV_STATE 0x80
+#define CBUS_DEVCAP_MHL_VERSION 0x81
+#define CBUS_DEVCAP_DEV_CAT 0x82
+#define CBUS_DEVCAP_ADOPTER_ID_H 0x83
+#define CBUS_DEVCAP_ADOPTER_ID_L 0x84
+#define CBUS_DEVCAP_VID_LINK_MODE 0x85
+#define CBUS_DEVCAP_AUD_LINK_MODE 0x86
+#define CBUS_DEVCAP_VIDEO_TYPE 0x87
+#define CBUS_DEVCAP_LOG_DEV_MAP 0x88
+#define CBUS_DEVCAP_BANDWIDTH 0x89
+#define CBUS_DEVCAP_DEV_FEATURE_FLAG 0x8A
+#define CBUS_DEVCAP_DEVICE_ID_H 0x8B
+#define CBUS_DEVCAP_DEVICE_ID_L 0x8C
+#define CBUS_DEVCAP_SCRATCHPAD_SIZE 0x8D
+#define CBUS_DEVCAP_INT_STAT_SIZE 0x8E
+#define CBUS_DEVCAP_RESERVED 0x8F
+#define CBUS_MHL_STATUS_REG_0 0xB0
+#define CBUS_MHL_STATUS_REG_1 0xB1
+
+/* TPI registers */
+#define TPI_DPD_REG 0x3D
+
+/* timeouts */
+#define T_SRC_VBUS_CBUS_TO_STABLE 200
+#define T_SRC_CBUS_FLOAT 100
+#define T_SRC_CBUS_DEGLITCH 2
+#define T_SRC_RXSENSE_DEGLITCH 110
+
+enum sii9234_state {
+ ST_OFF,
+ ST_D3,
+ ST_RGND_INIT,
+ ST_RGND_1K,
+ ST_RSEN_HIGH,
+ ST_MHL_ESTABLISHED,
+ ST_FAILURE_DISCOVERY,
+ ST_FAILURE,
+};
+
+struct sii9234 {
+ struct i2c_client *client[4];
+ int i2c_error;
+ int gpio_n_reset;
+ int gpio_int;
+ struct regulator *vcc_supply;
+ int irq;
+
+ enum sii9234_state state;
+ struct mutex lock;
+
+ /* Extcon */
+ struct extcon_specific_cable_nb extcon_dev;
+ struct notifier_block extcon_nb;
+ struct work_struct extcon_wq;
+ bool extcon_attached;
+};
+
+enum sii9234_client_id {
+ I2C_MHL,
+ I2C_TPI,
+ I2C_HDMI,
+ I2C_CBUS,
+};
+
+#define sii9234_dev(sii9234) (&(sii9234)->client[I2C_MHL]->dev)
+
+static char *sii9234_client_name[] = {
+ [I2C_MHL] = "MHL",
+ [I2C_TPI] = "TPI",
+ [I2C_HDMI] = "HDMI",
+ [I2C_CBUS] = "CBUS",
+};
+
+static int sii9234_writeb(struct sii9234 *sii9234, int id, int offset,
+ int value)
+{
+ int ret;
+ struct i2c_client *client = sii9234->client[id];
+ struct device *dev = sii9234_dev(sii9234);
+
+ if (sii9234->i2c_error)
+ return sii9234->i2c_error;
+
+ ret = i2c_smbus_write_byte_data(client, offset, value);
+ if (ret < 0)
+ dev_err(dev, "writeb: %4s[0x%02x] <- 0x%02x\n",
+ sii9234_client_name[id], offset, value);
+ sii9234->i2c_error = ret;
+ return ret;
+}
+
+static int sii9234_writebm(struct sii9234 *sii9234, int id, int offset,
+ int value, int mask)
+{
+ int ret;
+ struct i2c_client *client = sii9234->client[id];
+ struct device *dev = sii9234_dev(sii9234);
+
+ if (sii9234->i2c_error)
+ return sii9234->i2c_error;
+
+ ret = i2c_smbus_write_byte(client, offset);
+ if (ret < 0) {
+ dev_err(dev, "writebm: %4s[0x%02x] <- 0x%02x\n",
+ sii9234_client_name[id], offset, value);
+ sii9234->i2c_error = ret;
+ return ret;
+ }
+
+ ret = i2c_smbus_read_byte(client);
+ if (ret < 0) {
+ dev_err(dev, "writebm: %4s[0x%02x] <- 0x%02x\n",
+ sii9234_client_name[id], offset, value);
+ sii9234->i2c_error = ret;
+ return ret;
+ }
+
+ value = (value & mask) | (ret & ~mask);
+
+ ret = i2c_smbus_write_byte_data(client, offset, value);
+ if (ret < 0) {
+ dev_err(dev, "writebm: %4s[0x%02x] <- 0x%02x\n",
+ sii9234_client_name[id], offset, value);
+ sii9234->i2c_error = ret;
+ }
+ return ret;
+}
+
+static int sii9234_readb(struct sii9234 *sii9234, int id, int offset)
+{
+ int ret;
+ struct i2c_client *client = sii9234->client[id];
+ struct device *dev = sii9234_dev(sii9234);
+
+ if (sii9234->i2c_error)
+ return sii9234->i2c_error;
+
+ ret = i2c_smbus_write_byte(client, offset);
+ if (ret < 0) {
+ dev_err(dev, "readb: %4s[0x%02x]\n",
+ sii9234_client_name[id], offset);
+ sii9234->i2c_error = ret;
+ return ret;
+ }
+
+ ret = i2c_smbus_read_byte(client);
+ if (ret < 0) {
+ dev_err(dev, "readb: %4s[0x%02x]\n",
+ sii9234_client_name[id], offset);
+ sii9234->i2c_error = ret;
+ }
+
+ return ret;
+}
+
+static int sii9234_clear_error(struct sii9234 *sii9234)
+{
+ int ret = sii9234->i2c_error;
+
+ sii9234->i2c_error = 0;
+ return ret;
+}
+
+#define mhl_tx_writeb(sii9234, offset, value) \
+ sii9234_writeb(sii9234, I2C_MHL, offset, value)
+#define mhl_tx_writebm(sii9234, offset, value, mask) \
+ sii9234_writebm(sii9234, I2C_MHL, offset, value, mask)
+#define mhl_tx_readb(sii9234, offset) \
+ sii9234_readb(sii9234, I2C_MHL, offset)
+#define cbus_writeb(sii9234, offset, value) \
+ sii9234_writeb(sii9234, I2C_CBUS, offset, value)
+#define cbus_writebm(sii9234, offset, value, mask) \
+ sii9234_writebm(sii9234, I2C_CBUS, offset, value, mask)
+#define cbus_readb(sii9234, offset) \
+ sii9234_readb(sii9234, I2C_CBUS, offset)
+#define hdmi_writeb(sii9234, offset, value) \
+ sii9234_writeb(sii9234, I2C_HDMI, offset, value)
+#define hdmi_writebm(sii9234, offset, value, mask) \
+ sii9234_writebm(sii9234, I2C_HDMI, offset, value, mask)
+#define hdmi_readb(sii9234, offset) \
+ sii9234_readb(sii9234, I2C_HDMI, offset)
+#define tpi_writeb(sii9234, offset, value) \
+ sii9234_writeb(sii9234, I2C_TPI, offset, value)
+#define tpi_writebm(sii9234, offset, value, mask) \
+ sii9234_writebm(sii9234, I2C_TPI, offset, value, mask)
+#define tpi_readb(sii9234, offset) \
+ sii9234_readb(sii9234, I2C_TPI, offset)
+
+static u8 sii9234_tmds_control(struct sii9234 *sii9234, bool enable)
+{
+ mhl_tx_writebm(sii9234, MHL_TX_TMDS_CCTRL, enable ? ~0 : 0, 0x10);
+ mhl_tx_writebm(sii9234, MHL_TX_INT_CTRL_REG, enable ? ~0 : 0, 0x30);
+ return sii9234_clear_error(sii9234);
+}
+
+static int sii9234_cbus_reset(struct sii9234 *sii9234)
+{
+ int i;
+
+ /* Reset CBUS */
+ mhl_tx_writebm(sii9234, MHL_TX_SRST, ~0, 1 << 3);
+ /* CBUS deglitch - 2ms */
+ msleep(T_SRC_CBUS_DEGLITCH);
+ mhl_tx_writebm(sii9234, MHL_TX_SRST, 0, 1 << 3);
+
+ for (i = 0; i < 4; i++) {
+ /* Enable WRITE_STAT interrupt for writes to all
+ 4 MSC Status registers. */
+ cbus_writeb(sii9234, 0xE0 + i, 0xF2);
+ /*Enable SET_INT interrupt for writes to all
+ 4 MSC Interrupt registers. */
+ cbus_writeb(sii9234, 0xF0 + i, 0xF2);
+ }
+
+ return sii9234_clear_error(sii9234);
+}
+
+/* require to chek mhl imformation of samsung in cbus_init_register*/
+static int sii9234_cbus_init(struct sii9234 *sii9234)
+{
+ cbus_writeb(sii9234, 0x07, 0xF2);
+ cbus_writeb(sii9234, 0x40, 0x03);
+ cbus_writeb(sii9234, 0x42, 0x06);
+ cbus_writeb(sii9234, 0x36, 0x0C);
+ cbus_writeb(sii9234, 0x3D, 0xFD);
+ cbus_writeb(sii9234, 0x1C, 0x01);
+ cbus_writeb(sii9234, 0x1D, 0x0F);
+ cbus_writeb(sii9234, 0x44, 0x02);
+ /* Setup our devcap */
+ /* To meet cts 6.3.10.1 spec */
+ cbus_writeb(sii9234, CBUS_DEVCAP_DEV_STATE, 0x00);
+ /* mhl version 1.1 */
+ cbus_writeb(sii9234, CBUS_DEVCAP_MHL_VERSION, 0x11);
+ cbus_writeb(sii9234, CBUS_DEVCAP_DEV_CAT, 0x02);
+ cbus_writeb(sii9234, CBUS_DEVCAP_ADOPTER_ID_H, 0x01);
+ cbus_writeb(sii9234, CBUS_DEVCAP_ADOPTER_ID_L, 0x41);
+ /* YCbCr444, RGB444 */
+ cbus_writeb(sii9234, CBUS_DEVCAP_VID_LINK_MODE, 0x03);
+ cbus_writeb(sii9234, CBUS_DEVCAP_VIDEO_TYPE, 0);
+ cbus_writeb(sii9234, CBUS_DEVCAP_LOG_DEV_MAP, 0x80);
+ cbus_writeb(sii9234, CBUS_DEVCAP_BANDWIDTH, 0x0F);
+ cbus_writeb(sii9234, CBUS_DEVCAP_DEV_FEATURE_FLAG, 0x07);
+ cbus_writeb(sii9234, CBUS_DEVCAP_DEVICE_ID_H, 0x0);
+ cbus_writeb(sii9234, CBUS_DEVCAP_DEVICE_ID_L, 0x0);
+ cbus_writeb(sii9234, CBUS_DEVCAP_SCRATCHPAD_SIZE, 0x10);
+ cbus_writeb(sii9234, CBUS_DEVCAP_INT_STAT_SIZE, 0x33);
+ cbus_writeb(sii9234, CBUS_DEVCAP_RESERVED, 0);
+ cbus_writebm(sii9234, 0x31, 0x0C, 0x0C);
+ cbus_writeb(sii9234, 0x30, 0x01);
+ cbus_writebm(sii9234, 0x3C, 0x30, 0x38);
+ cbus_writebm(sii9234, 0x22, 0x0D, 0x0F);
+ cbus_writebm(sii9234, 0x2E, 0x15, 0x15);
+ cbus_writeb(sii9234, CBUS_INTR1_ENABLE_REG, 0);
+ cbus_writeb(sii9234, CBUS_INTR2_ENABLE_REG, 0);
+
+ return sii9234_clear_error(sii9234);
+}
+
+static void force_usb_id_switch_open(struct sii9234 *sii9234)
+{
+ /*Disable CBUS discovery */
+ mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL1_REG, 0, 0x01);
+ /*Force USB ID switch to open */
+ mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL6_REG, ~0, USB_ID_OVR);
+ mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL3_REG, ~0, 0x86);
+ /*Force upstream HPD to 0 when not in MHL mode. */
+ mhl_tx_writebm(sii9234, MHL_TX_INT_CTRL_REG, 0, 0x30);
+}
+
+static void release_usb_id_switch_open(struct sii9234 *sii9234)
+{
+ msleep(T_SRC_CBUS_FLOAT);
+ /* clear USB ID switch to open */
+ mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL6_REG, 0, USB_ID_OVR);
+ /* Enable CBUS discovery */
+ mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL1_REG, ~0, 0x01);
+}
+
+static int sii9234_power_init(struct sii9234 *sii9234)
+{
+ /* Force the SiI9234 into the D0 state. */
+ tpi_writeb(sii9234, TPI_DPD_REG, 0x3F);
+ /* Enable TxPLL Clock */
+ hdmi_writeb(sii9234, HDMI_RX_TMDS_CLK_EN_REG, 0x01);
+ /* Enable Tx Clock Path & Equalizer */
+ hdmi_writeb(sii9234, HDMI_RX_TMDS_CH_EN_REG, 0x15);
+ /* Power Up TMDS */
+ mhl_tx_writeb(sii9234, 0x08, 0x35);
+ return sii9234_clear_error(sii9234);
+}
+
+static int sii9234_hdmi_init(struct sii9234 *sii9234)
+{
+ /* Analog PLL Control bits 5:4 = 2b00 as per char. team. */
+ hdmi_writeb(sii9234, HDMI_RX_TMDS0_CCTRL1_REG, 0xC1);
+ /* PLL Calrefsel */
+ hdmi_writeb(sii9234, HDMI_RX_PLL_CALREFSEL_REG, 0x03);
+ /* VCO Cal */
+ hdmi_writeb(sii9234, HDMI_RX_PLL_VCOCAL_REG, 0x20);
+ /* Auto EQ */
+ hdmi_writeb(sii9234, HDMI_RX_EQ_DATA0_REG, 0x8A);
+ /* Auto EQ */
+ hdmi_writeb(sii9234, HDMI_RX_EQ_DATA1_REG, 0x6A);
+ /* Auto EQ */
+ hdmi_writeb(sii9234, HDMI_RX_EQ_DATA2_REG, 0xAA);
+ /* Auto EQ */
+ hdmi_writeb(sii9234, HDMI_RX_EQ_DATA3_REG, 0xCA);
+ /* Auto EQ */
+ hdmi_writeb(sii9234, HDMI_RX_EQ_DATA4_REG, 0xEA);
+ /* Manual zone */
+ hdmi_writeb(sii9234, HDMI_RX_TMDS_ZONE_CTRL_REG, 0xA0);
+ /* PLL Mode Value */
+ hdmi_writeb(sii9234, HDMI_RX_TMDS_MODE_CTRL_REG, 0x00);
+ mhl_tx_writeb(sii9234, MHL_TX_TMDS_CCTRL, 0x34);
+ hdmi_writeb(sii9234, 0x45, 0x44);
+ /* Rx PLL BW ~ 4MHz */
+ hdmi_writeb(sii9234, 0x31, 0x0A);
+ /* Analog PLL Control * bits 5:4 = 2b00 as per char. team. */
+ hdmi_writeb(sii9234, HDMI_RX_TMDS0_CCTRL1_REG, 0xC1);
+
+ return sii9234_clear_error(sii9234);
+}
+
+static int sii9234_mhl_tx_ctl_int(struct sii9234 *sii9234)
+{
+ mhl_tx_writeb(sii9234, MHL_TX_MHLTX_CTL1_REG, 0xD0);
+ mhl_tx_writeb(sii9234, MHL_TX_MHLTX_CTL2_REG, 0xFC);
+ mhl_tx_writeb(sii9234, MHL_TX_MHLTX_CTL4_REG, 0xEB);
+ mhl_tx_writeb(sii9234, MHL_TX_MHLTX_CTL7_REG, 0x0C);
+ return sii9234_clear_error(sii9234);
+}
+
+static int sii9234_reset(struct sii9234 *sii9234)
+{
+ int ret;
+
+ sii9234_clear_error(sii9234);
+
+ ret = sii9234_power_init(sii9234);
+ if (ret < 0)
+ return ret;
+ ret = sii9234_cbus_reset(sii9234);
+ if (ret < 0)
+ return ret;
+ ret = sii9234_hdmi_init(sii9234);
+ if (ret < 0)
+ return ret;
+ ret = sii9234_mhl_tx_ctl_int(sii9234);
+ if (ret < 0)
+ return ret;
+
+ /* Enable HDCP Compliance safety */
+ mhl_tx_writeb(sii9234, 0x2B, 0x01);
+ /* CBUS discovery cycle time for each drive and float = 150us */
+ mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL1_REG, 0x04, 0x06);
+ /* Clear bit 6 (reg_skip_rgnd) */
+ mhl_tx_writeb(sii9234, MHL_TX_DISC_CTRL2_REG, (1 << 7) /* Reserved */
+ | 2 << ATT_THRESH_SHIFT | DEGLITCH_TIME_50MS);
+ /* Changed from 66 to 65 for 94[1:0] = 01 = 5k reg_cbusmhl_pup_sel */
+ /* 1.8V CBUS VTH & GND threshold */
+ /*To meet CTS 3.3.7.2 spec */
+ mhl_tx_writeb(sii9234, MHL_TX_DISC_CTRL5_REG, 0x77);
+ /* set bit 2 and 3, which is Initiator Timeout */
+ cbus_writebm(sii9234, CBUS_LINK_CONTROL_2_REG, ~0, 0x0C);
+ mhl_tx_writeb(sii9234, MHL_TX_MHLTX_CTL6_REG, 0xA0);
+ /* RGND & single discovery attempt (RGND blocking) */
+ mhl_tx_writeb(sii9234, MHL_TX_DISC_CTRL6_REG, BLOCK_RGND_INT |
+ DVRFLT_SEL | SINGLE_ATT);
+ /* Use VBUS path of discovery state machine */
+ mhl_tx_writeb(sii9234, MHL_TX_DISC_CTRL8_REG, 0);
+ /* 0x92[3] sets the CBUS / ID switch */
+ mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL6_REG, ~0, USB_ID_OVR);
+ /* To allow RGND engine to operate correctly.
+ * When moving the chip from D2 to D0 (power up, init regs)
+ * the values should be
+ * 94[1:0] = 01 reg_cbusmhl_pup_sel[1:0] should be set for 5k
+ * 93[7:6] = 10 reg_cbusdisc_pup_sel[1:0] should be
+ * set for 10k (default)
+ * 93[5:4] = 00 reg_cbusidle_pup_sel[1:0] = open (default)
+ */
+ mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL3_REG, ~0, 0x86);
+ /* change from CC to 8C to match 5K */
+ /*To meet CTS 3.3.72 spec */
+ mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL4_REG, ~0, 0x8C);
+ /* Configure the interrupt as active high */
+ mhl_tx_writebm(sii9234, MHL_TX_INT_CTRL_REG, 0, 0x06);
+
+ msleep(25);
+
+ /* release usb_id switch */
+ mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL6_REG, 0, USB_ID_OVR);
+ mhl_tx_writeb(sii9234, MHL_TX_DISC_CTRL1_REG, 0x27);
+
+ ret = sii9234_clear_error(sii9234);
+ if (ret < 0)
+ return ret;
+ ret = sii9234_cbus_init(sii9234);
+ if (ret < 0)
+ return ret;
+
+ /* Enable Auto soft reset on SCDT = 0 */
+ mhl_tx_writeb(sii9234, 0x05, 0x04);
+ /* HDMI Transcode mode enable */
+ mhl_tx_writeb(sii9234, 0x0D, 0x1C);
+ mhl_tx_writeb(sii9234, MHL_TX_INTR4_ENABLE_REG,
+ RGND_READY_MASK | CBUS_LKOUT_MASK |
+ MHL_DISC_FAIL_MASK | MHL_EST_MASK);
+ mhl_tx_writeb(sii9234, MHL_TX_INTR1_ENABLE_REG, 0x60);
+
+ /* this point is very importand before megsure RGND impedance */
+ force_usb_id_switch_open(sii9234);
+ mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL4_REG, 0, 0xF0);
+ mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL5_REG, 0, 0x03);
+ release_usb_id_switch_open(sii9234);
+ /*end of this */
+
+ /* Force upstream HPD to 0 when not in MHL mode */
+ mhl_tx_writebm(sii9234, MHL_TX_INT_CTRL_REG, 0, 1 << 5);
+ mhl_tx_writebm(sii9234, MHL_TX_INT_CTRL_REG, ~0, 1 << 4);
+
+ return sii9234_clear_error(sii9234);
+}
+
+static int sii9234_goto_d3(struct sii9234 *sii9234)
+{
+ int ret;
+ struct device *dev = sii9234_dev(sii9234);
+
+ dev_dbg(dev, "sii9234: detection started d3\n");
+
+ ret = sii9234_reset(sii9234);
+ if (ret < 0)
+ goto exit;
+
+ hdmi_writeb(sii9234, 0x01, 0x03);
+ tpi_writebm(sii9234, TPI_DPD_REG, 0, 1);
+ /* I2C above is expected to fail because power goes down */
+ sii9234_clear_error(sii9234);
+
+ sii9234->state = ST_D3;
+
+ return 0;
+ exit:
+ dev_err(dev, "sii9234_goto_d3() failed\n");
+ return -1;
+}
+
+#define sii9234_hw_on(sii9234) \
+ regulator_enable((sii9234)->vcc_supply)
+
+static void sii9234_hw_off(struct sii9234 *sii9234)
+{
+ gpio_direction_output(sii9234->gpio_n_reset, 0);
+ usleep_range(10000, 20000);
+ gpio_direction_output(sii9234->gpio_n_reset, 1);
+ regulator_disable(sii9234->vcc_supply);
+ gpio_direction_output(sii9234->gpio_n_reset, 0);
+}
+
+static void sii9234_hw_reset(struct sii9234 *sii9234)
+{
+ gpio_direction_output(sii9234->gpio_n_reset, 0);
+ usleep_range(10000, 20000);
+ gpio_direction_output(sii9234->gpio_n_reset, 1);
+}
+
+static void sii9234_cable_in(struct sii9234 *sii9234)
+{
+ int ret;
+
+ mutex_lock(&sii9234->lock);
+ if (sii9234->state != ST_OFF)
+ goto unlock;
+ ret = sii9234_hw_on(sii9234);
+ if (ret < 0)
+ goto unlock;
+
+ sii9234_hw_reset(sii9234);
+ sii9234_goto_d3(sii9234);
+ enable_irq(sii9234->irq);
+
+unlock:
+ mutex_unlock(&sii9234->lock);
+}
+
+static void sii9234_cable_out(struct sii9234 *sii9234)
+{
+ mutex_lock(&sii9234->lock);
+
+ if (sii9234->state == ST_OFF)
+ goto unlock;
+
+ disable_irq_nosync(sii9234->irq);
+ tpi_writeb(sii9234, TPI_DPD_REG, 0);
+ /*turn on&off hpd festure for only QCT HDMI */
+ sii9234_hw_off(sii9234);
+
+ sii9234->state = ST_OFF;
+
+unlock:
+ mutex_unlock(&sii9234->lock);
+}
+
+static enum sii9234_state sii9234_rgnd_ready_irq(struct sii9234 *sii9234)
+{
+ int value;
+ struct device *dev = sii9234_dev(sii9234);
+
+ if (sii9234->state == ST_D3) {
+ int ret;
+
+ dev_dbg(dev, "RGND_READY_INT\n");
+ sii9234_hw_reset(sii9234);
+
+ ret = sii9234_reset(sii9234);
+ if (ret < 0) {
+ dev_err(dev, "sii9234_reset() failed\n");
+ return ST_FAILURE;
+ }
+
+ return ST_RGND_INIT;
+ }
+
+ /* got interrupt in inappropriate state */
+ if (sii9234->state != ST_RGND_INIT)
+ return ST_FAILURE;
+
+ value = mhl_tx_readb(sii9234, MHL_TX_STAT2_REG);
+ if (sii9234_clear_error(sii9234))
+ return ST_FAILURE;
+
+ if ((value & RGND_INTP_MASK) != RGND_INTP_1K) {
+ dev_warn(dev, "RGND is not 1k\n");
+ return ST_RGND_INIT;
+ }
+ dev_dbg(dev, "RGND 1K!!\n");
+ /* After applying RGND patch, there is some issue
+ about discovry failure
+ This point is add to fix that problem */
+ mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL4_REG, ~0, 0x8C);
+ mhl_tx_writeb(sii9234, MHL_TX_DISC_CTRL5_REG, 0x77);
+ mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL6_REG, ~0, 0x05);
+ if (sii9234_clear_error(sii9234))
+ return ST_FAILURE;
+
+ usleep_range(T_SRC_VBUS_CBUS_TO_STABLE * USEC_PER_MSEC,
+ T_SRC_VBUS_CBUS_TO_STABLE * USEC_PER_MSEC);
+
+ return ST_RGND_1K;
+}
+
+static enum sii9234_state sii9234_mhl_established(struct sii9234 *sii9234)
+{
+ dev_dbg(sii9234_dev(sii9234), "mhl est interrupt\n");
+
+ /* discovery override */
+ mhl_tx_writeb(sii9234, MHL_TX_MHLTX_CTL1_REG, 0x10);
+ /* increase DDC translation layer timer (byte mode) */
+ cbus_writeb(sii9234, 0x07, 0x32);
+ cbus_writebm(sii9234, 0x44, ~0, 1 << 1);
+ /* Keep the discovery enabled. Need RGND interrupt */
+ mhl_tx_writebm(sii9234, MHL_TX_DISC_CTRL1_REG, ~0, 1);
+ mhl_tx_writeb(sii9234, MHL_TX_INTR1_ENABLE_REG,
+ RSEN_CHANGE_INT_MASK | HPD_CHANGE_INT_MASK);
+
+ if (sii9234_clear_error(sii9234))
+ return ST_FAILURE;
+
+ return ST_MHL_ESTABLISHED;
+}
+
+static enum sii9234_state sii9234_hpd_change(struct sii9234 *sii9234)
+{
+ int value;
+
+ value = cbus_readb(sii9234, CBUS_MSC_REQ_ABORT_REASON_REG);
+ if (sii9234_clear_error(sii9234))
+ return ST_FAILURE;
+
+ if (value & SET_HPD_DOWNSTREAM) {
+ dev_info(sii9234_dev(sii9234), "HPD High\n");
+ /* Downstream HPD High, Enable TMDS */
+ sii9234_tmds_control(sii9234, true);
+ /*turn on&off hpd festure for only QCT HDMI */
+ } else {
+ dev_info(sii9234_dev(sii9234), "HPD Low\n");
+ /* Downstream HPD Low, Disable TMDS */
+ sii9234_tmds_control(sii9234, false);
+ }
+
+ return sii9234->state;
+}
+
+static enum sii9234_state sii9234_rsen_change(struct sii9234 *sii9234)
+{
+ int value;
+ struct device *dev = sii9234_dev(sii9234);
+
+ /* work_around code to handle worng interrupt */
+ if (sii9234->state != ST_RGND_1K) {
+ dev_err(dev, "RSEN_HIGH without RGND_1K\n");
+ return ST_FAILURE;
+ }
+ value = mhl_tx_readb(sii9234, MHL_TX_SYSSTAT_REG);
+ if (value < 0)
+ return ST_FAILURE;
+
+ if (value & RSEN_STATUS) {
+ dev_info(dev, "MHL cable connected.. RSEN High\n");
+ return ST_RSEN_HIGH;
+ }
+ dev_info(dev, "RSEN lost\n");
+ /* Once RSEN loss is confirmed,we need to check
+ * based on cable status and chip power status,whether
+ * it is SINK Loss(HDMI cable not connected, TV Off)
+ * or MHL cable disconnection
+ * TODO: Define the below mhl_disconnection()
+ */
+ msleep(T_SRC_RXSENSE_DEGLITCH);
+ value = mhl_tx_readb(sii9234, MHL_TX_SYSSTAT_REG);
+ if (value < 0)
+ return ST_FAILURE;
+ dev_dbg(dev, "sys_stat: %x\n", value);
+
+ if (value & RSEN_STATUS) {
+ dev_info(dev, "RSEN recovery\n");
+ return ST_RSEN_HIGH;
+ }
+ dev_info(dev, "RSEN Really LOW\n");
+ /*To meet CTS 3.3.22.2 spec */
+ sii9234_tmds_control(sii9234, false);
+ force_usb_id_switch_open(sii9234);
+ release_usb_id_switch_open(sii9234);
+
+ return ST_FAILURE;
+}
+
+static irqreturn_t sii9234_irq_thread(int irq, void *data)
+{
+ struct sii9234 *sii9234 = data;
+ int intr1, intr4;
+ int intr1_en, intr4_en;
+ int cbus_intr1, cbus_intr2;
+ struct device *dev = sii9234_dev(sii9234);
+
+ dev_dbg(dev, "%s\n", __func__);
+
+ msleep(30);
+
+ mutex_lock(&sii9234->lock);
+
+ intr1 = mhl_tx_readb(sii9234, MHL_TX_INTR1_REG);
+ intr4 = mhl_tx_readb(sii9234, MHL_TX_INTR4_REG);
+ intr1_en = mhl_tx_readb(sii9234, MHL_TX_INTR1_ENABLE_REG);
+ intr4_en = mhl_tx_readb(sii9234, MHL_TX_INTR4_ENABLE_REG);
+ cbus_intr1 = cbus_readb(sii9234, CBUS_INT_STATUS_1_REG);
+ cbus_intr2 = cbus_readb(sii9234, CBUS_INT_STATUS_2_REG);
+
+ if (sii9234_clear_error(sii9234))
+ goto done;
+
+ dev_dbg(dev, "irq %02x/%02x %02x/%02x %02x/%02x\n",
+ intr1, intr1_en, intr4, intr4_en, cbus_intr1, cbus_intr2);
+
+ if (intr4 & RGND_READY_INT)
+ sii9234->state = sii9234_rgnd_ready_irq(sii9234);
+ if (intr1 & RSEN_CHANGE_INT)
+ sii9234->state = sii9234_rsen_change(sii9234);
+ if (intr4 & MHL_EST_INT)
+ sii9234->state = sii9234_mhl_established(sii9234);
+ if (intr1 & HPD_CHANGE_INT)
+ sii9234->state = sii9234_hpd_change(sii9234);
+ if (intr4 & CBUS_LKOUT_INT)
+ sii9234->state = ST_FAILURE;
+ if (intr4 & MHL_DISC_FAIL_INT)
+ sii9234->state = ST_FAILURE_DISCOVERY;
+
+ done:
+ /* clean interrupt status and pending flags */
+ mhl_tx_writeb(sii9234, MHL_TX_INTR1_REG, intr1);
+ mhl_tx_writeb(sii9234, MHL_TX_INTR4_REG, intr4);
+ cbus_writeb(sii9234, CBUS_MHL_STATUS_REG_0, 0xFF);
+ cbus_writeb(sii9234, CBUS_MHL_STATUS_REG_1, 0xFF);
+ cbus_writeb(sii9234, CBUS_INT_STATUS_1_REG, cbus_intr1);
+ cbus_writeb(sii9234, CBUS_INT_STATUS_2_REG, cbus_intr2);
+
+ sii9234_clear_error(sii9234);
+
+ if (sii9234->state == ST_FAILURE) {
+ dev_info(dev, "try to reset after failure\n");
+ sii9234_hw_reset(sii9234);
+ sii9234_goto_d3(sii9234);
+ }
+
+ if (sii9234->state == ST_FAILURE_DISCOVERY) {
+ dev_err(dev, "discovery failed, no power for MHL?\n");
+ tpi_writebm(sii9234, TPI_DPD_REG, 0, 1);
+ sii9234->state = ST_D3;
+ }
+
+ mutex_unlock(&sii9234->lock);
+
+ return IRQ_HANDLED;
+}
+
+static void sii9234_extcon_work(struct work_struct *work)
+{
+ struct sii9234 *sii9234 =
+ container_of(work, struct sii9234, extcon_wq);
+
+ dev_info(sii9234_dev(sii9234), "MHL is %s\n",
+ sii9234->extcon_attached ? "attached" : "detached");
+
+ if (sii9234->extcon_attached)
+ sii9234_cable_in(sii9234);
+ else
+ sii9234_cable_out(sii9234);
+}
+
+static int sii9234_extcon_notifier(struct notifier_block *self,
+ unsigned long event, void *ptr)
+{
+ struct sii9234 *sii9234 =
+ container_of(self, struct sii9234, extcon_nb);
+
+ sii9234->extcon_attached = event;
+ schedule_work(&sii9234->extcon_wq);
+
+ return NOTIFY_DONE;
+}
+
+static int sii9234_extcon_init(struct sii9234 *sii9234)
+{
+ struct device *dev = &sii9234->client[I2C_MHL]->dev;
+ struct extcon_dev *edev;
+ int ret;
+
+ if (of_property_read_bool(dev->of_node, "extcon")) {
+ edev = extcon_get_edev_by_phandle(dev, 0);
+ if (IS_ERR(edev)) {
+ dev_err(dev, "failed to acquire extcon device\n");
+ return PTR_ERR(edev);
+ }
+
+ sii9234->extcon_attached = extcon_get_cable_state(edev, "MHL");
+ dev_info(dev, "extcon(MHL) = %d\n", sii9234->extcon_attached);
+
+ sii9234->extcon_nb.notifier_call = sii9234_extcon_notifier;
+ ret = extcon_register_interest(&sii9234->extcon_dev, edev->name,
+ "MHL", &sii9234->extcon_nb);
+
+ if (ret) {
+ dev_err(dev, "failed to register notifier for MHL\n");
+ return ret;
+ }
+ INIT_WORK(&sii9234->extcon_wq, sii9234_extcon_work);
+ } else {
+ dev_info(dev, "no extcon found, switching to 'always on' mode\n");
+ sii9234->extcon_attached = true;
+ }
+ return 0;
+}
+
+static int sii9234_init_resources(struct sii9234 *sii9234,
+ struct i2c_client *client)
+{
+ struct i2c_adapter *adapter = to_i2c_adapter(client->dev.parent);
+ struct device *dev = &client->dev;
+ int ret;
+
+ if (!dev->of_node) {
+ dev_err(dev, "not DT device\n");
+ return -ENODEV;
+ }
+
+ sii9234->gpio_n_reset = of_get_named_gpio(dev->of_node,
+ "gpio-reset", 0);
+ if (!gpio_is_valid(sii9234->gpio_n_reset)) {
+ dev_err(dev, "failed to get gpio-reset from DT\n");
+ return -ENODEV;
+ }
+ sii9234->gpio_int = of_get_named_gpio(dev->of_node, "gpio-int", 0);
+ if (!gpio_is_valid(sii9234->gpio_int)) {
+ dev_err(dev, "failed to get gpio-int from DT\n");
+ return -ENODEV;
+ }
+
+ ret = devm_gpio_request(dev, sii9234->gpio_n_reset, "MHL_RST");
+ if (ret) {
+ dev_err(dev, "failed to acquire MHL_RST gpio\n");
+ return ret;
+ }
+
+ ret = devm_gpio_request(dev, sii9234->gpio_int, "MHL_INT");
+ if (ret) {
+ dev_err(dev, "failed to request MHL_INT gpio\n");
+ return ret;
+ }
+
+ sii9234->vcc_supply = devm_regulator_get(dev, "vcc");
+ if (IS_ERR(sii9234->vcc_supply)) {
+ dev_err(dev, "failed to acquire regulator vcc\n");
+ return PTR_ERR(sii9234->vcc_supply);
+ }
+
+ sii9234->client[I2C_MHL] = client;
+
+ sii9234->client[I2C_TPI] = i2c_new_dummy(adapter, 0x7A >> 1);
+ if (!sii9234->client[I2C_TPI]) {
+ dev_err(dev, "failed to create TPI client\n");
+ return -ENODEV;
+ }
+
+ sii9234->client[I2C_HDMI] = i2c_new_dummy(adapter, 0x92 >> 1);
+ if (!sii9234->client[I2C_HDMI]) {
+ dev_err(dev, "failed to create HDMI RX client\n");
+ goto fail_tpi;
+ }
+
+ sii9234->client[I2C_CBUS] = i2c_new_dummy(adapter, 0xC8 >> 1);
+ if (!sii9234->client[I2C_CBUS]) {
+ dev_err(dev, "failed to create CBUS client\n");
+ goto fail_hdmi;
+ }
+
+ return 0;
+
+fail_hdmi:
+ i2c_unregister_device(sii9234->client[I2C_HDMI]);
+fail_tpi:
+ i2c_unregister_device(sii9234->client[I2C_TPI]);
+
+ return -ENODEV;
+}
+
+static void sii9234_deinit_resources(struct sii9234 *sii9234)
+{
+ i2c_unregister_device(sii9234->client[I2C_CBUS]);
+ i2c_unregister_device(sii9234->client[I2C_HDMI]);
+ i2c_unregister_device(sii9234->client[I2C_TPI]);
+}
+
+static int sii9234_mhl_tx_i2c_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct i2c_adapter *adapter = to_i2c_adapter(client->dev.parent);
+ struct sii9234 *sii9234;
+ struct device *dev = &client->dev;
+ int ret;
+
+ if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) {
+ dev_err(dev, "I2C adapter lacks SMBUS feature\n");
+ return -EIO;
+ }
+
+ sii9234 = devm_kzalloc(dev, sizeof(struct sii9234), GFP_KERNEL);
+ if (!sii9234) {
+ dev_err(dev, "not enough memory\n");
+ return -ENOMEM;
+ }
+
+ mutex_init(&sii9234->lock);
+
+ ret = sii9234_init_resources(sii9234, client);
+ if (ret < 0) {
+ dev_err(&client->dev, "failed to initialize sii9234 resources\n");
+ return ret;
+ }
+ ret = sii9234_hw_on(sii9234);
+ if (ret) {
+ dev_err(&client->dev, "failed to enable power\n");
+ goto err_resource;
+ }
+ sii9234_hw_reset(sii9234);
+
+ i2c_set_clientdata(client, sii9234);
+
+ sii9234->irq = gpio_to_irq(sii9234->gpio_int);
+ ret = devm_request_threaded_irq(dev, sii9234->irq, NULL,
+ sii9234_irq_thread, IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
+ "sii9234", sii9234);
+ if (ret < 0) {
+ dev_err(dev, "failed to request MHL interrupt\n");
+ goto err_hw_power;
+ }
+
+ disable_irq(sii9234->irq);
+
+ ret = sii9234_extcon_init(sii9234);
+ if (ret < 0) {
+ dev_err(dev, "failed to initialize EXTCON\n");
+ goto err_hw_power;
+ }
+
+ /* Force MHL connect EVENT for platforms with no EXTCON */
+ if (sii9234->extcon_attached)
+ sii9234_cable_in(sii9234);
+
+ return 0;
+
+err_hw_power:
+ sii9234_hw_off(sii9234);
+
+err_resource:
+ sii9234_deinit_resources(sii9234);
+
+ return ret;
+}
+
+static int sii9234_mhl_tx_i2c_remove(struct i2c_client *client)
+{
+ struct sii9234 *sii9234 = i2c_get_clientdata(client);
+
+ extcon_unregister_interest(&sii9234->extcon_dev);
+ if (sii9234->extcon_attached)
+ sii9234_cable_out(sii9234);
+ sii9234_deinit_resources(sii9234);
+
+ return 0;
+}
+
+static const struct of_device_id sii9234_dt_match[] = {
+ { .compatible = "sil,sii9234" },
+ { },
+};
+MODULE_DEVICE_TABLE(of, sii9234_dt_match);
+
+static const struct i2c_device_id sii9234_id[] = {
+ { "SII9234", 0 },
+ { },
+};
+
+MODULE_DEVICE_TABLE(i2c, sii9234_id);
+static struct i2c_driver sii9234_driver = {
+ .driver = {
+ .name = "sii9234",
+ .owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(sii9234_dt_match),
+ },
+ .probe = sii9234_mhl_tx_i2c_probe,
+ .remove = sii9234_mhl_tx_i2c_remove,
+ .id_table = sii9234_id,
+};
+
+module_i2c_driver(sii9234_driver);
+MODULE_LICENSE("GPL");