diff mbox

[1/2] phy: qcom: Add driver for QCOM IPQ806x SATA PHY

Message ID 1402600724-20651-1-git-send-email-galak@codeaurora.org (mailing list archive)
State New, archived
Headers show

Commit Message

Kumar Gala June 12, 2014, 7:18 p.m. UTC
Add a PHY driver for uses with AHCI based SATA controller driver on the
IPQ806x family of SoCs.

Signed-off-by: Kumar Gala <galak@codeaurora.org>
---
 drivers/phy/Kconfig                 |   6 ++
 drivers/phy/Makefile                |   1 +
 drivers/phy/phy-qcom-ipq806x-sata.c | 204 ++++++++++++++++++++++++++++++++++++
 3 files changed, 211 insertions(+)
 create mode 100644 drivers/phy/phy-qcom-ipq806x-sata.c

Comments

Stephen Boyd June 12, 2014, 8:16 p.m. UTC | #1
On 06/12/14 12:18, Kumar Gala wrote:
> +
> +struct qcom_ipq806x_sata_phy {
> +	struct device *dev;

Is this used?

> +	void __iomem *mmio;
> +	struct clk *cfg_clk;
[...]
> +
> +static int qcom_ipq806x_sata_phy_init(struct phy *generic_phy)
> +{
> +	struct qcom_ipq806x_sata_phy *phy = phy_get_drvdata(generic_phy);
> +	u32 reg = 0;

unnecessary initialization

> +
> +static int qcom_ipq806x_sata_phy_exit(struct phy *generic_phy)
> +{
> +	struct qcom_ipq806x_sata_phy *phy = phy_get_drvdata(generic_phy);
> +	u32 reg = 0;

unnecessary initialization

>
> +static int qcom_ipq806x_sata_phy_probe(struct platform_device *pdev)
> +{
> +	struct qcom_ipq806x_sata_phy *phy;
> +	struct device *dev = &pdev->dev;
> +	struct resource *res;
> +	struct phy_provider *phy_provider;
> +	struct phy *generic_phy;
> +	int ret;
> +
> +	phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
> +	if (!phy) {
> +		dev_err(dev, "%s: failed to allocate phy\n", __func__);
> +		return -ENOMEM;
> +	}
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	phy->mmio = devm_ioremap_resource(dev, res);
> +	if (IS_ERR(phy->mmio)) {
> +		dev_err(dev, "%s: phy mmio get resource failed\n", __func__);

Unnecessary error message.

> +		return PTR_ERR(phy->mmio);
> +	}
> +
> +	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> +	if (IS_ERR(phy_provider)) {
> +		dev_err(dev, "%s: failed to register phy\n", __func__);
> +		return PTR_ERR(phy_provider);
> +	}
> +
> +	generic_phy = devm_phy_create(dev, &qcom_ipq806x_sata_phy_ops, NULL);
> +	if (IS_ERR(generic_phy)) {
> +		dev_err(dev, "%s: failed to create phy\n", __func__);
> +		return PTR_ERR(generic_phy);
> +	}
> +
> +	phy->cfg_clk = devm_clk_get(dev, "cfg");
> +	if (IS_ERR(phy->cfg_clk)) {
> +		dev_err(dev, "Failed to get sata cfg clock\n");
> +		return PTR_ERR(phy->cfg_clk);
> +	}
> +
> +	ret = clk_prepare_enable(phy->cfg_clk);
> +	if (ret)
> +		return ret;

Shouldn't there be a remove that disables this clock?
Kishon Vijay Abraham I June 16, 2014, 10:04 a.m. UTC | #2
Hi,

On Friday 13 June 2014 12:48 AM, Kumar Gala wrote:
> Add a PHY driver for uses with AHCI based SATA controller driver on the
> IPQ806x family of SoCs.
> 
> Signed-off-by: Kumar Gala <galak@codeaurora.org>
> ---
>  drivers/phy/Kconfig                 |   6 ++
>  drivers/phy/Makefile                |   1 +
>  drivers/phy/phy-qcom-ipq806x-sata.c | 204 ++++++++++++++++++++++++++++++++++++
>  3 files changed, 211 insertions(+)
>  create mode 100644 drivers/phy/phy-qcom-ipq806x-sata.c
> 
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index 16a2f06..52bfb93 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -178,4 +178,10 @@ config PHY_XGENE
>  	help
>  	  This option enables support for APM X-Gene SoC multi-purpose PHY.
>  
> +config PHY_QCOM_IPQ806X_SATA
> +	tristate "Qualcomm IPQ806x SATA SerDes/PHY driver"
> +	depends on ARCH_QCOM
> +	depends on OF
depends on HAS_IOMEM?
> +	select GENERIC_PHY
> +
>  endmenu
> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
> index b4f1d57..d950317 100644
> --- a/drivers/phy/Makefile
> +++ b/drivers/phy/Makefile
> @@ -20,3 +20,4 @@ phy-exynos-usb2-$(CONFIG_PHY_EXYNOS4X12_USB2)	+= phy-exynos4x12-usb2.o
>  phy-exynos-usb2-$(CONFIG_PHY_EXYNOS5250_USB2)	+= phy-exynos5250-usb2.o
>  obj-$(CONFIG_PHY_EXYNOS5_USBDRD)	+= phy-exynos5-usbdrd.o
>  obj-$(CONFIG_PHY_XGENE)			+= phy-xgene.o
> +obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA)	+= phy-qcom-ipq806x-sata.o
> diff --git a/drivers/phy/phy-qcom-ipq806x-sata.c b/drivers/phy/phy-qcom-ipq806x-sata.c
> new file mode 100644
> index 0000000..fc57340
> --- /dev/null
> +++ b/drivers/phy/phy-qcom-ipq806x-sata.c
> @@ -0,0 +1,204 @@
> +/*
> + * Copyright (c) 2014, The Linux Foundation. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 and
> + * only version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/time.h>
> +#include <linux/delay.h>
> +#include <linux/clk.h>
> +#include <linux/slab.h>
> +#include <linux/platform_device.h>
> +#include <linux/phy/phy.h>
> +
> +struct qcom_ipq806x_sata_phy {
> +	struct device *dev;

dev is not used anywhere. remove it.
> +	void __iomem *mmio;
> +	struct clk *cfg_clk;
> +};
> +
> +#define __set(v, a, b)	(((v) << (b)) & GENMASK(a, b))
> +
> +#define SATA_PHY_P0_PARAM0		0x200
> +#define SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN3(x)	__set(x, 17, 12)
> +#define SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN3_MASK	GENMASK(17, 12)
> +#define SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN2(x)	__set(x, 11, 6)
> +#define SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN2_MASK	GENMASK(11, 6)
> +#define SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN1(x)	__set(x, 5, 0)
> +#define SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN1_MASK	GENMASK(5, 0)
> +
> +#define SATA_PHY_P0_PARAM1		0x204
> +#define SATA_PHY_P0_PARAM1_RESERVED_BITS31_21(x)	__set(x, 31, 21)
> +#define SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN3(x)	__set(x, 20, 14)
> +#define SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN3_MASK	GENMASK(20, 14)
> +#define SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN2(x)	__set(x, 13, 7)
> +#define SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN2_MASK	GENMASK(13, 7)
> +#define SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN1(x)	__set(x, 6, 0)
> +#define SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN1_MASK	GENMASK(6, 0)
> +
> +#define SATA_PHY_P0_PARAM2		0x208
> +#define SATA_PHY_P0_PARAM2_RX_EQ(x)	__set(x, 20, 18)
> +#define SATA_PHY_P0_PARAM2_RX_EQ_MASK	GENMASK(20, 18)
> +
> +#define SATA_PHY_P0_PARAM3		0x20C
> +#define SATA_PHY_SSC_EN			0x8
> +#define SATA_PHY_P0_PARAM4		0x210
> +#define SATA_PHY_REF_SSP_EN		0x2
> +#define SATA_PHY_RESET			0x1
> +
> +static inline void qcom_ipq806x_sata_delay_us(unsigned int delay)
> +{
> +	/* sleep for max. 50us more to combine processor wakeups */
> +	usleep_range(delay, delay + 50);
> +}
> +
> +static int qcom_ipq806x_sata_phy_init(struct phy *generic_phy)
> +{
> +	struct qcom_ipq806x_sata_phy *phy = phy_get_drvdata(generic_phy);
> +	u32 reg = 0;
> +
> +	/* Setting SSC_EN to 1 */
> +	reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM3);

Why readl_relaxed?
> +	reg = reg | SATA_PHY_SSC_EN;
> +	writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM3);
> +
> +	reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM0) &
> +			~(SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN3_MASK |
> +			  SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN2_MASK |
> +			  SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN1_MASK);
> +	reg |= SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN3(0xf);
> +	writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM0);
> +
> +	reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM1) &
> +			~(SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN3_MASK |
> +			  SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN2_MASK |
> +			  SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN1_MASK);
> +	reg |= SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN3(0x55) |
> +		SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN2(0x55) |
> +		SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN1(0x55);
> +	writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM1);
> +
> +	reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM2) &
> +		~SATA_PHY_P0_PARAM2_RX_EQ_MASK;
> +	reg |= SATA_PHY_P0_PARAM2_RX_EQ(0x3);
> +	writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM2);
> +
> +	/* Setting PHY_RESET to 1 */
> +	reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM4);
> +	reg = reg | SATA_PHY_RESET;
> +	writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM4);
> +
> +	/* Setting REF_SSP_EN to 1 */
> +	reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM4);
> +	reg = reg | SATA_PHY_REF_SSP_EN | SATA_PHY_RESET;
> +	writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM4);
> +	mb();
> +	qcom_ipq806x_sata_delay_us(20);
> +
> +	/* Clearing PHY_RESET to 0 */
> +	reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM4);
> +	reg = reg & ~SATA_PHY_RESET;
> +	writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM4);
> +
> +	return 0;
> +}
> +
> +static int qcom_ipq806x_sata_phy_exit(struct phy *generic_phy)
> +{
> +	struct qcom_ipq806x_sata_phy *phy = phy_get_drvdata(generic_phy);
> +	u32 reg = 0;
> +
> +	/* Setting PHY_RESET to 1 */
> +	reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM4);
> +	reg = reg | SATA_PHY_RESET;
> +	writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM4);
> +
> +	return 0;
> +}
> +
> +static struct phy_ops qcom_ipq806x_sata_phy_ops = {
> +	.init		= qcom_ipq806x_sata_phy_init,
> +	.exit		= qcom_ipq806x_sata_phy_exit,
> +	.owner		= THIS_MODULE,
> +};
> +
> +static int qcom_ipq806x_sata_phy_probe(struct platform_device *pdev)
> +{
> +	struct qcom_ipq806x_sata_phy *phy;
> +	struct device *dev = &pdev->dev;
> +	struct resource *res;
> +	struct phy_provider *phy_provider;
> +	struct phy *generic_phy;
> +	int ret;
> +
> +	phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
> +	if (!phy) {
> +		dev_err(dev, "%s: failed to allocate phy\n", __func__);
> +		return -ENOMEM;
> +	}
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	phy->mmio = devm_ioremap_resource(dev, res);
> +	if (IS_ERR(phy->mmio)) {
> +		dev_err(dev, "%s: phy mmio get resource failed\n", __func__);
> +		return PTR_ERR(phy->mmio);
> +	}
> +
> +	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> +	if (IS_ERR(phy_provider)) {
> +		dev_err(dev, "%s: failed to register phy\n", __func__);
> +		return PTR_ERR(phy_provider);
> +	}

phy_provider_register should be the last step. Move it after phy_set_drvdata().

Thanks
Kishon
Kumar Gala June 16, 2014, 7:51 p.m. UTC | #3
On Jun 16, 2014, at 5:04 AM, Kishon Vijay Abraham I <kishon@ti.com> wrote:

> Hi,
> 
> On Friday 13 June 2014 12:48 AM, Kumar Gala wrote:
>> Add a PHY driver for uses with AHCI based SATA controller driver on the
>> IPQ806x family of SoCs.
>> 
>> Signed-off-by: Kumar Gala <galak@codeaurora.org>
>> ---
>> drivers/phy/Kconfig                 |   6 ++
>> drivers/phy/Makefile                |   1 +
>> drivers/phy/phy-qcom-ipq806x-sata.c | 204 ++++++++++++++++++++++++++++++++++++
>> 3 files changed, 211 insertions(+)
>> create mode 100644 drivers/phy/phy-qcom-ipq806x-sata.c
>> 
>> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
>> index 16a2f06..52bfb93 100644
>> --- a/drivers/phy/Kconfig
>> +++ b/drivers/phy/Kconfig
>> @@ -178,4 +178,10 @@ config PHY_XGENE
>> 	help
>> 	  This option enables support for APM X-Gene SoC multi-purpose PHY.
>> 
>> +config PHY_QCOM_IPQ806X_SATA
>> +	tristate "Qualcomm IPQ806x SATA SerDes/PHY driver"
>> +	depends on ARCH_QCOM
>> +	depends on OF
> depends on HAS_IOMEM?

will add

>> +	select GENERIC_PHY
>> +
>> endmenu
>> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
>> index b4f1d57..d950317 100644
>> --- a/drivers/phy/Makefile
>> +++ b/drivers/phy/Makefile
>> @@ -20,3 +20,4 @@ phy-exynos-usb2-$(CONFIG_PHY_EXYNOS4X12_USB2)	+= phy-exynos4x12-usb2.o
>> phy-exynos-usb2-$(CONFIG_PHY_EXYNOS5250_USB2)	+= phy-exynos5250-usb2.o
>> obj-$(CONFIG_PHY_EXYNOS5_USBDRD)	+= phy-exynos5-usbdrd.o
>> obj-$(CONFIG_PHY_XGENE)			+= phy-xgene.o
>> +obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA)	+= phy-qcom-ipq806x-sata.o
>> diff --git a/drivers/phy/phy-qcom-ipq806x-sata.c b/drivers/phy/phy-qcom-ipq806x-sata.c
>> new file mode 100644
>> index 0000000..fc57340
>> --- /dev/null
>> +++ b/drivers/phy/phy-qcom-ipq806x-sata.c
>> @@ -0,0 +1,204 @@
>> +/*
>> + * Copyright (c) 2014, The Linux Foundation. All rights reserved.
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 and
>> + * only version 2 as published by the Free Software Foundation.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + * GNU General Public License for more details.
>> + */
>> +
>> +#include <linux/io.h>
>> +#include <linux/kernel.h>
>> +#include <linux/module.h>
>> +#include <linux/of.h>
>> +#include <linux/of_address.h>
>> +#include <linux/time.h>
>> +#include <linux/delay.h>
>> +#include <linux/clk.h>
>> +#include <linux/slab.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/phy/phy.h>
>> +
>> +struct qcom_ipq806x_sata_phy {
>> +	struct device *dev;
> 
> dev is not used anywhere. remove it.

already done in v2

>> +	void __iomem *mmio;
>> +	struct clk *cfg_clk;
>> +};
>> +
>> +#define __set(v, a, b)	(((v) << (b)) & GENMASK(a, b))
>> +
>> +#define SATA_PHY_P0_PARAM0		0x200
>> +#define SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN3(x)	__set(x, 17, 12)
>> +#define SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN3_MASK	GENMASK(17, 12)
>> +#define SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN2(x)	__set(x, 11, 6)
>> +#define SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN2_MASK	GENMASK(11, 6)
>> +#define SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN1(x)	__set(x, 5, 0)
>> +#define SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN1_MASK	GENMASK(5, 0)
>> +
>> +#define SATA_PHY_P0_PARAM1		0x204
>> +#define SATA_PHY_P0_PARAM1_RESERVED_BITS31_21(x)	__set(x, 31, 21)
>> +#define SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN3(x)	__set(x, 20, 14)
>> +#define SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN3_MASK	GENMASK(20, 14)
>> +#define SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN2(x)	__set(x, 13, 7)
>> +#define SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN2_MASK	GENMASK(13, 7)
>> +#define SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN1(x)	__set(x, 6, 0)
>> +#define SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN1_MASK	GENMASK(6, 0)
>> +
>> +#define SATA_PHY_P0_PARAM2		0x208
>> +#define SATA_PHY_P0_PARAM2_RX_EQ(x)	__set(x, 20, 18)
>> +#define SATA_PHY_P0_PARAM2_RX_EQ_MASK	GENMASK(20, 18)
>> +
>> +#define SATA_PHY_P0_PARAM3		0x20C
>> +#define SATA_PHY_SSC_EN			0x8
>> +#define SATA_PHY_P0_PARAM4		0x210
>> +#define SATA_PHY_REF_SSP_EN		0x2
>> +#define SATA_PHY_RESET			0x1
>> +
>> +static inline void qcom_ipq806x_sata_delay_us(unsigned int delay)
>> +{
>> +	/* sleep for max. 50us more to combine processor wakeups */
>> +	usleep_range(delay, delay + 50);
>> +}
>> +
>> +static int qcom_ipq806x_sata_phy_init(struct phy *generic_phy)
>> +{
>> +	struct qcom_ipq806x_sata_phy *phy = phy_get_drvdata(generic_phy);
>> +	u32 reg = 0;
>> +
>> +	/* Setting SSC_EN to 1 */
>> +	reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM3);
> 
> Why readl_relaxed?

because there is no need for readl’s memory barriers here.

>> +	reg = reg | SATA_PHY_SSC_EN;
>> +	writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM3);
>> +
>> +	reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM0) &
>> +			~(SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN3_MASK |
>> +			  SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN2_MASK |
>> +			  SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN1_MASK);
>> +	reg |= SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN3(0xf);
>> +	writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM0);
>> +
>> +	reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM1) &
>> +			~(SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN3_MASK |
>> +			  SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN2_MASK |
>> +			  SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN1_MASK);
>> +	reg |= SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN3(0x55) |
>> +		SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN2(0x55) |
>> +		SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN1(0x55);
>> +	writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM1);
>> +
>> +	reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM2) &
>> +		~SATA_PHY_P0_PARAM2_RX_EQ_MASK;
>> +	reg |= SATA_PHY_P0_PARAM2_RX_EQ(0x3);
>> +	writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM2);
>> +
>> +	/* Setting PHY_RESET to 1 */
>> +	reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM4);
>> +	reg = reg | SATA_PHY_RESET;
>> +	writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM4);
>> +
>> +	/* Setting REF_SSP_EN to 1 */
>> +	reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM4);
>> +	reg = reg | SATA_PHY_REF_SSP_EN | SATA_PHY_RESET;
>> +	writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM4);
>> +	mb();
>> +	qcom_ipq806x_sata_delay_us(20);
>> +
>> +	/* Clearing PHY_RESET to 0 */
>> +	reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM4);
>> +	reg = reg & ~SATA_PHY_RESET;
>> +	writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM4);
>> +
>> +	return 0;
>> +}
>> +
>> +static int qcom_ipq806x_sata_phy_exit(struct phy *generic_phy)
>> +{
>> +	struct qcom_ipq806x_sata_phy *phy = phy_get_drvdata(generic_phy);
>> +	u32 reg = 0;
>> +
>> +	/* Setting PHY_RESET to 1 */
>> +	reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM4);
>> +	reg = reg | SATA_PHY_RESET;
>> +	writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM4);
>> +
>> +	return 0;
>> +}
>> +
>> +static struct phy_ops qcom_ipq806x_sata_phy_ops = {
>> +	.init		= qcom_ipq806x_sata_phy_init,
>> +	.exit		= qcom_ipq806x_sata_phy_exit,
>> +	.owner		= THIS_MODULE,
>> +};
>> +
>> +static int qcom_ipq806x_sata_phy_probe(struct platform_device *pdev)
>> +{
>> +	struct qcom_ipq806x_sata_phy *phy;
>> +	struct device *dev = &pdev->dev;
>> +	struct resource *res;
>> +	struct phy_provider *phy_provider;
>> +	struct phy *generic_phy;
>> +	int ret;
>> +
>> +	phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
>> +	if (!phy) {
>> +		dev_err(dev, "%s: failed to allocate phy\n", __func__);
>> +		return -ENOMEM;
>> +	}
>> +
>> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> +	phy->mmio = devm_ioremap_resource(dev, res);
>> +	if (IS_ERR(phy->mmio)) {
>> +		dev_err(dev, "%s: phy mmio get resource failed\n", __func__);
>> +		return PTR_ERR(phy->mmio);
>> +	}
>> +
>> +	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
>> +	if (IS_ERR(phy_provider)) {
>> +		dev_err(dev, "%s: failed to register phy\n", __func__);
>> +		return PTR_ERR(phy_provider);
>> +	}
> 
> phy_provider_register should be the last step. Move it after phy_set_drvdata().

will fix

> 
> Thanks
> Kishon
> --
> To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
diff mbox

Patch

diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index 16a2f06..52bfb93 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -178,4 +178,10 @@  config PHY_XGENE
 	help
 	  This option enables support for APM X-Gene SoC multi-purpose PHY.
 
+config PHY_QCOM_IPQ806X_SATA
+	tristate "Qualcomm IPQ806x SATA SerDes/PHY driver"
+	depends on ARCH_QCOM
+	depends on OF
+	select GENERIC_PHY
+
 endmenu
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index b4f1d57..d950317 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -20,3 +20,4 @@  phy-exynos-usb2-$(CONFIG_PHY_EXYNOS4X12_USB2)	+= phy-exynos4x12-usb2.o
 phy-exynos-usb2-$(CONFIG_PHY_EXYNOS5250_USB2)	+= phy-exynos5250-usb2.o
 obj-$(CONFIG_PHY_EXYNOS5_USBDRD)	+= phy-exynos5-usbdrd.o
 obj-$(CONFIG_PHY_XGENE)			+= phy-xgene.o
+obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA)	+= phy-qcom-ipq806x-sata.o
diff --git a/drivers/phy/phy-qcom-ipq806x-sata.c b/drivers/phy/phy-qcom-ipq806x-sata.c
new file mode 100644
index 0000000..fc57340
--- /dev/null
+++ b/drivers/phy/phy-qcom-ipq806x-sata.c
@@ -0,0 +1,204 @@ 
+/*
+ * Copyright (c) 2014, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/time.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/phy/phy.h>
+
+struct qcom_ipq806x_sata_phy {
+	struct device *dev;
+	void __iomem *mmio;
+	struct clk *cfg_clk;
+};
+
+#define __set(v, a, b)	(((v) << (b)) & GENMASK(a, b))
+
+#define SATA_PHY_P0_PARAM0		0x200
+#define SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN3(x)	__set(x, 17, 12)
+#define SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN3_MASK	GENMASK(17, 12)
+#define SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN2(x)	__set(x, 11, 6)
+#define SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN2_MASK	GENMASK(11, 6)
+#define SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN1(x)	__set(x, 5, 0)
+#define SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN1_MASK	GENMASK(5, 0)
+
+#define SATA_PHY_P0_PARAM1		0x204
+#define SATA_PHY_P0_PARAM1_RESERVED_BITS31_21(x)	__set(x, 31, 21)
+#define SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN3(x)	__set(x, 20, 14)
+#define SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN3_MASK	GENMASK(20, 14)
+#define SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN2(x)	__set(x, 13, 7)
+#define SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN2_MASK	GENMASK(13, 7)
+#define SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN1(x)	__set(x, 6, 0)
+#define SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN1_MASK	GENMASK(6, 0)
+
+#define SATA_PHY_P0_PARAM2		0x208
+#define SATA_PHY_P0_PARAM2_RX_EQ(x)	__set(x, 20, 18)
+#define SATA_PHY_P0_PARAM2_RX_EQ_MASK	GENMASK(20, 18)
+
+#define SATA_PHY_P0_PARAM3		0x20C
+#define SATA_PHY_SSC_EN			0x8
+#define SATA_PHY_P0_PARAM4		0x210
+#define SATA_PHY_REF_SSP_EN		0x2
+#define SATA_PHY_RESET			0x1
+
+static inline void qcom_ipq806x_sata_delay_us(unsigned int delay)
+{
+	/* sleep for max. 50us more to combine processor wakeups */
+	usleep_range(delay, delay + 50);
+}
+
+static int qcom_ipq806x_sata_phy_init(struct phy *generic_phy)
+{
+	struct qcom_ipq806x_sata_phy *phy = phy_get_drvdata(generic_phy);
+	u32 reg = 0;
+
+	/* Setting SSC_EN to 1 */
+	reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM3);
+	reg = reg | SATA_PHY_SSC_EN;
+	writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM3);
+
+	reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM0) &
+			~(SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN3_MASK |
+			  SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN2_MASK |
+			  SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN1_MASK);
+	reg |= SATA_PHY_P0_PARAM0_P0_TX_PREEMPH_GEN3(0xf);
+	writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM0);
+
+	reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM1) &
+			~(SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN3_MASK |
+			  SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN2_MASK |
+			  SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN1_MASK);
+	reg |= SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN3(0x55) |
+		SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN2(0x55) |
+		SATA_PHY_P0_PARAM1_P0_TX_AMPLITUDE_GEN1(0x55);
+	writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM1);
+
+	reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM2) &
+		~SATA_PHY_P0_PARAM2_RX_EQ_MASK;
+	reg |= SATA_PHY_P0_PARAM2_RX_EQ(0x3);
+	writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM2);
+
+	/* Setting PHY_RESET to 1 */
+	reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM4);
+	reg = reg | SATA_PHY_RESET;
+	writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM4);
+
+	/* Setting REF_SSP_EN to 1 */
+	reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM4);
+	reg = reg | SATA_PHY_REF_SSP_EN | SATA_PHY_RESET;
+	writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM4);
+	mb();
+	qcom_ipq806x_sata_delay_us(20);
+
+	/* Clearing PHY_RESET to 0 */
+	reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM4);
+	reg = reg & ~SATA_PHY_RESET;
+	writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM4);
+
+	return 0;
+}
+
+static int qcom_ipq806x_sata_phy_exit(struct phy *generic_phy)
+{
+	struct qcom_ipq806x_sata_phy *phy = phy_get_drvdata(generic_phy);
+	u32 reg = 0;
+
+	/* Setting PHY_RESET to 1 */
+	reg = readl_relaxed(phy->mmio + SATA_PHY_P0_PARAM4);
+	reg = reg | SATA_PHY_RESET;
+	writel_relaxed(reg, phy->mmio + SATA_PHY_P0_PARAM4);
+
+	return 0;
+}
+
+static struct phy_ops qcom_ipq806x_sata_phy_ops = {
+	.init		= qcom_ipq806x_sata_phy_init,
+	.exit		= qcom_ipq806x_sata_phy_exit,
+	.owner		= THIS_MODULE,
+};
+
+static int qcom_ipq806x_sata_phy_probe(struct platform_device *pdev)
+{
+	struct qcom_ipq806x_sata_phy *phy;
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	struct phy_provider *phy_provider;
+	struct phy *generic_phy;
+	int ret;
+
+	phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+	if (!phy) {
+		dev_err(dev, "%s: failed to allocate phy\n", __func__);
+		return -ENOMEM;
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	phy->mmio = devm_ioremap_resource(dev, res);
+	if (IS_ERR(phy->mmio)) {
+		dev_err(dev, "%s: phy mmio get resource failed\n", __func__);
+		return PTR_ERR(phy->mmio);
+	}
+
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	if (IS_ERR(phy_provider)) {
+		dev_err(dev, "%s: failed to register phy\n", __func__);
+		return PTR_ERR(phy_provider);
+	}
+
+	generic_phy = devm_phy_create(dev, &qcom_ipq806x_sata_phy_ops, NULL);
+	if (IS_ERR(generic_phy)) {
+		dev_err(dev, "%s: failed to create phy\n", __func__);
+		return PTR_ERR(generic_phy);
+	}
+
+	phy->cfg_clk = devm_clk_get(dev, "cfg");
+	if (IS_ERR(phy->cfg_clk)) {
+		dev_err(dev, "Failed to get sata cfg clock\n");
+		return PTR_ERR(phy->cfg_clk);
+	}
+
+	ret = clk_prepare_enable(phy->cfg_clk);
+	if (ret)
+		return ret;
+
+	phy->dev = dev;
+	phy_set_drvdata(generic_phy, phy);
+
+	return 0;
+}
+
+static const struct of_device_id qcom_ipq806x_sata_phy_of_match[] = {
+	{ .compatible = "qcom,ipq806x-sata-phy" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, qcom_ipq806x_sata_phy_of_match);
+
+static struct platform_driver qcom_ipq806x_sata_phy_driver = {
+	.probe	= qcom_ipq806x_sata_phy_probe,
+	.driver = {
+		.name	= "qcom-ipq806x-sata-phy",
+		.owner	= THIS_MODULE,
+		.of_match_table	= qcom_ipq806x_sata_phy_of_match,
+	}
+};
+module_platform_driver(qcom_ipq806x_sata_phy_driver);
+
+MODULE_DESCRIPTION("QCOM IPQ806x SATA PHY driver");
+MODULE_LICENSE("GPL v2");