diff mbox

[v4,04/14] clk: max77686: Improve Maxim 77686 PMIC clocks binding

Message ID 1403723019-6212-5-git-send-email-javier.martinez@collabora.co.uk (mailing list archive)
State New, archived
Headers show

Commit Message

Javier Martinez Canillas June 25, 2014, 7:03 p.m. UTC
Like most clock drivers, the Maxim 77686 PMIC clock binding
follows the convention that the "#clock-cells" property is
used to specify the number of cells in a clock provider.

But the binding document is not clear enough that it shall
be set to 1 since the PMIC support multiple clocks outputs.

Also, explain that the clocks identifiers are defined in a
header file that can be included by Device Tree source with
client nodes to avoid using magic numbers.

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
---

Changes since v3:
 - Don't change clock-names property to make clear that it's
   the consumer clock name and should not match the producer clock.
   Suggested by Doug Anderson.

 Documentation/devicetree/bindings/clock/maxim,max77686.txt | 13 +++++++++----
 1 file changed, 9 insertions(+), 4 deletions(-)

Comments

Doug Anderson June 25, 2014, 7:54 p.m. UTC | #1
Javier,

On Wed, Jun 25, 2014 at 12:03 PM, Javier Martinez Canillas
<javier.martinez@collabora.co.uk> wrote:
> Like most clock drivers, the Maxim 77686 PMIC clock binding
> follows the convention that the "#clock-cells" property is
> used to specify the number of cells in a clock provider.
>
> But the binding document is not clear enough that it shall
> be set to 1 since the PMIC support multiple clocks outputs.
>
> Also, explain that the clocks identifiers are defined in a
> header file that can be included by Device Tree source with
> client nodes to avoid using magic numbers.
>
> Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
> ---
>
> Changes since v3:
>  - Don't change clock-names property to make clear that it's
>    the consumer clock name and should not match the producer clock.
>    Suggested by Doug Anderson.
>
>  Documentation/devicetree/bindings/clock/maxim,max77686.txt | 13 +++++++++----
>  1 file changed, 9 insertions(+), 4 deletions(-)

Reviewed-by: Doug Anderson <dianders@chromium.org>
diff mbox

Patch

diff --git a/Documentation/devicetree/bindings/clock/maxim,max77686.txt b/Documentation/devicetree/bindings/clock/maxim,max77686.txt
index 96ce71b..48e00bb 100644
--- a/Documentation/devicetree/bindings/clock/maxim,max77686.txt
+++ b/Documentation/devicetree/bindings/clock/maxim,max77686.txt
@@ -9,13 +9,18 @@  The MAX77686 contains three 32.768khz clock outputs that can be controlled
 Following properties should be presend in main device node of the MFD chip.
 
 Required properties:
-- #clock-cells: simple one-cell clock specifier format is used, where the
-  only cell is used as an index of the clock inside the provider. Following
-  indices are allowed:
+
+- #clock-cells: from common clock binding; shall be set to 1.
+
+Each clock is assigned an identifier and client nodes can use this identifier
+to specify the clock which they consume. Following indices are allowed:
     - 0: 32khz_ap clock,
     - 1: 32khz_cp clock,
     - 2: 32khz_pmic clock.
 
+Clocks are defined as preprocessor macros in dt-bindings/clock/maxim,max77686.h
+header and can be used in device tree sources.
+
 Example: Node of the MFD chip
 
 	max77686: max77686@09 {
@@ -34,5 +39,5 @@  Example: Clock consumer node
 		compatible = "bar,foo";
 		/* ... */
 		clock-names = "my-clock";
-		clocks = <&max77686 2>;
+		clocks = <&max77686 MAX77686_CLK_PMIC>;
 	};