diff mbox

ARM: i.MX: Remove Phytec i.MX27 PCM038/PCM970 board files

Message ID 1408792329-32248-1-git-send-email-shc_work@mail.ru (mailing list archive)
State New, archived
Headers show

Commit Message

Alexander Shiyan Aug. 23, 2014, 11:12 a.m. UTC
pcm970-baseboard.c and mach-pcm038.c can be replaced with their
devicetree equivalents: imx27-phytec-phycore-rdk.dts and
imx27-phytec-phycore-som.dtsi respectively, so remove the board files.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
---
 arch/arm/configs/imx_v4_v5_defconfig |   1 -
 arch/arm/mach-imx/Kconfig            |  30 ---
 arch/arm/mach-imx/Makefile           |   2 -
 arch/arm/mach-imx/board-pcm038.h     |  36 ----
 arch/arm/mach-imx/mach-pcm038.c      | 358 -----------------------------------
 arch/arm/mach-imx/pcm970-baseboard.c | 231 ----------------------
 6 files changed, 658 deletions(-)
 delete mode 100644 arch/arm/mach-imx/board-pcm038.h
 delete mode 100644 arch/arm/mach-imx/mach-pcm038.c
 delete mode 100644 arch/arm/mach-imx/pcm970-baseboard.c

Comments

Shawn Guo Aug. 25, 2014, 7:49 a.m. UTC | #1
On Sat, Aug 23, 2014 at 03:12:09PM +0400, Alexander Shiyan wrote:
> pcm970-baseboard.c and mach-pcm038.c can be replaced with their
> devicetree equivalents: imx27-phytec-phycore-rdk.dts and
> imx27-phytec-phycore-som.dtsi respectively, so remove the board files.
> 
> Signed-off-by: Alexander Shiyan <shc_work@mail.ru>

Applied, thanks.
diff mbox

Patch

diff --git a/arch/arm/configs/imx_v4_v5_defconfig b/arch/arm/configs/imx_v4_v5_defconfig
index f53074c..9d73e69 100644
--- a/arch/arm/configs/imx_v4_v5_defconfig
+++ b/arch/arm/configs/imx_v4_v5_defconfig
@@ -30,7 +30,6 @@  CONFIG_MACH_MX25_3DS=y
 CONFIG_MACH_EUKREA_CPUIMX25SD=y
 CONFIG_MACH_IMX25_DT=y
 CONFIG_MACH_MX27ADS=y
-CONFIG_MACH_PCM038=y
 CONFIG_MACH_MX27_3DS=y
 CONFIG_MACH_IMX27_VISSTRIM_M10=y
 CONFIG_MACH_PCA100=y
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index d48901a..64161aa 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -231,36 +231,6 @@  config MACH_MX27ADS
 	  Include support for MX27ADS platform. This includes specific
 	  configurations for the board and its peripherals.
 
-config MACH_PCM038
-	bool "Phytec phyCORE-i.MX27 CPU module (pcm038)"
-	select IMX_HAVE_PLATFORM_IMX2_WDT
-	select IMX_HAVE_PLATFORM_IMX_I2C
-	select IMX_HAVE_PLATFORM_IMX_UART
-	select IMX_HAVE_PLATFORM_MXC_EHCI
-	select IMX_HAVE_PLATFORM_MXC_NAND
-	select IMX_HAVE_PLATFORM_MXC_W1
-	select IMX_HAVE_PLATFORM_SPI_IMX
-	select USB_ULPI_VIEWPORT if USB_ULPI
-	select SOC_IMX27
-	help
-	  Include support for phyCORE-i.MX27 (aka pcm038) platform. This
-	  includes specific configurations for the module and its peripherals.
-
-choice
-	prompt "Baseboard"
-	depends on MACH_PCM038
-	default MACH_PCM970_BASEBOARD
-
-config MACH_PCM970_BASEBOARD
-	bool "PHYTEC PCM970 development board"
-	select IMX_HAVE_PLATFORM_IMX_FB
-	select IMX_HAVE_PLATFORM_MXC_MMC
-	help
-	  This adds board specific devices that can be found on Phytec's
-	  PCM970 evaluation board.
-
-endchoice
-
 config MACH_MX27_3DS
 	bool "MX27PDK platform"
 	select IMX_HAVE_PLATFORM_FSL_USB2_UDC
diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile
index 614df32..9f1c359 100644
--- a/arch/arm/mach-imx/Makefile
+++ b/arch/arm/mach-imx/Makefile
@@ -57,8 +57,6 @@  obj-$(CONFIG_MACH_IMX25_DT) += imx25-dt.o
 
 # i.MX27 based machines
 obj-$(CONFIG_MACH_MX27ADS) += mach-mx27ads.o
-obj-$(CONFIG_MACH_PCM038) += mach-pcm038.o
-obj-$(CONFIG_MACH_PCM970_BASEBOARD) += pcm970-baseboard.o
 obj-$(CONFIG_MACH_MX27_3DS) += mach-mx27_3ds.o
 obj-$(CONFIG_MACH_IMX27_VISSTRIM_M10) += mach-imx27_visstrim_m10.o
 obj-$(CONFIG_MACH_PCA100) += mach-pca100.o
diff --git a/arch/arm/mach-imx/board-pcm038.h b/arch/arm/mach-imx/board-pcm038.h
deleted file mode 100644
index 6f371e3..0000000
--- a/arch/arm/mach-imx/board-pcm038.h
+++ /dev/null
@@ -1,36 +0,0 @@ 
-/*
- * Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de)
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301, USA.
- */
-
-#ifndef __ASM_ARCH_MXC_BOARD_PCM038_H__
-#define __ASM_ARCH_MXC_BOARD_PCM038_H__
-
-#ifndef __ASSEMBLY__
-/*
- * This CPU module needs a baseboard to work. After basic initializing
- * its own devices, it calls the baseboard's init function.
- * TODO: Add your own baseboard init function and call it from
- * inside pcm038_init().
- *
- * This example here is for the development board. Refer pcm970-baseboard.c
- */
-
-extern void pcm970_baseboard_init(void);
-
-#endif
-
-#endif /* __ASM_ARCH_MXC_BOARD_PCM038_H__ */
diff --git a/arch/arm/mach-imx/mach-pcm038.c b/arch/arm/mach-imx/mach-pcm038.c
deleted file mode 100644
index ee862ad..0000000
--- a/arch/arm/mach-imx/mach-pcm038.c
+++ /dev/null
@@ -1,358 +0,0 @@ 
-/*
- * Copyright 2007 Robert Schwebel <r.schwebel@pengutronix.de>, Pengutronix
- * Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de)
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301, USA.
- */
-
-#include <linux/i2c.h>
-#include <linux/platform_data/at24.h>
-#include <linux/io.h>
-#include <linux/mtd/plat-ram.h>
-#include <linux/mtd/physmap.h>
-#include <linux/platform_device.h>
-#include <linux/regulator/machine.h>
-#include <linux/mfd/mc13783.h>
-#include <linux/spi/spi.h>
-#include <linux/irq.h>
-#include <linux/gpio.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/time.h>
-
-#include "board-pcm038.h"
-#include "common.h"
-#include "devices-imx27.h"
-#include "ehci.h"
-#include "hardware.h"
-#include "iomux-mx27.h"
-#include "ulpi.h"
-
-static const int pcm038_pins[] __initconst = {
-	/* UART1 */
-	PE12_PF_UART1_TXD,
-	PE13_PF_UART1_RXD,
-	PE14_PF_UART1_CTS,
-	PE15_PF_UART1_RTS,
-	/* UART2 */
-	PE3_PF_UART2_CTS,
-	PE4_PF_UART2_RTS,
-	PE6_PF_UART2_TXD,
-	PE7_PF_UART2_RXD,
-	/* UART3 */
-	PE8_PF_UART3_TXD,
-	PE9_PF_UART3_RXD,
-	PE10_PF_UART3_CTS,
-	PE11_PF_UART3_RTS,
-	/* FEC */
-	PD0_AIN_FEC_TXD0,
-	PD1_AIN_FEC_TXD1,
-	PD2_AIN_FEC_TXD2,
-	PD3_AIN_FEC_TXD3,
-	PD4_AOUT_FEC_RX_ER,
-	PD5_AOUT_FEC_RXD1,
-	PD6_AOUT_FEC_RXD2,
-	PD7_AOUT_FEC_RXD3,
-	PD8_AF_FEC_MDIO,
-	PD9_AIN_FEC_MDC,
-	PD10_AOUT_FEC_CRS,
-	PD11_AOUT_FEC_TX_CLK,
-	PD12_AOUT_FEC_RXD0,
-	PD13_AOUT_FEC_RX_DV,
-	PD14_AOUT_FEC_RX_CLK,
-	PD15_AOUT_FEC_COL,
-	PD16_AIN_FEC_TX_ER,
-	PF23_AIN_FEC_TX_EN,
-	/* I2C2 */
-	PC5_PF_I2C2_SDA,
-	PC6_PF_I2C2_SCL,
-	/* SPI1 */
-	PD25_PF_CSPI1_RDY,
-	PD29_PF_CSPI1_SCLK,
-	PD30_PF_CSPI1_MISO,
-	PD31_PF_CSPI1_MOSI,
-	/* SSI1 */
-	PC20_PF_SSI1_FS,
-	PC21_PF_SSI1_RXD,
-	PC22_PF_SSI1_TXD,
-	PC23_PF_SSI1_CLK,
-	/* SSI4 */
-	PC16_PF_SSI4_FS,
-	PC17_PF_SSI4_RXD,
-	PC18_PF_SSI4_TXD,
-	PC19_PF_SSI4_CLK,
-	/* USB host */
-	PA0_PF_USBH2_CLK,
-	PA1_PF_USBH2_DIR,
-	PA2_PF_USBH2_DATA7,
-	PA3_PF_USBH2_NXT,
-	PA4_PF_USBH2_STP,
-	PD19_AF_USBH2_DATA4,
-	PD20_AF_USBH2_DATA3,
-	PD21_AF_USBH2_DATA6,
-	PD22_AF_USBH2_DATA0,
-	PD23_AF_USBH2_DATA2,
-	PD24_AF_USBH2_DATA1,
-	PD26_AF_USBH2_DATA5,
-};
-
-/*
- * Phytec's PCM038 comes with 2MiB battery buffered SRAM,
- * 16 bit width
- */
-
-static struct platdata_mtd_ram pcm038_sram_data = {
-	.bankwidth = 2,
-};
-
-static struct resource pcm038_sram_resource = {
-	.start = MX27_CS1_BASE_ADDR,
-	.end   = MX27_CS1_BASE_ADDR + 512 * 1024 - 1,
-	.flags = IORESOURCE_MEM,
-};
-
-static struct platform_device pcm038_sram_mtd_device = {
-	.name = "mtd-ram",
-	.id = 0,
-	.dev = {
-		.platform_data = &pcm038_sram_data,
-	},
-	.num_resources = 1,
-	.resource = &pcm038_sram_resource,
-};
-
-/*
- * Phytec's phyCORE-i.MX27 comes with 32MiB flash,
- * 16 bit width
- */
-static struct physmap_flash_data pcm038_flash_data = {
-	.width = 2,
-};
-
-static struct resource pcm038_flash_resource = {
-	.start = 0xc0000000,
-	.end   = 0xc1ffffff,
-	.flags = IORESOURCE_MEM,
-};
-
-static struct platform_device pcm038_nor_mtd_device = {
-	.name = "physmap-flash",
-	.id = 0,
-	.dev = {
-		.platform_data = &pcm038_flash_data,
-	},
-	.num_resources = 1,
-	.resource = &pcm038_flash_resource,
-};
-
-static const struct imxuart_platform_data uart_pdata __initconst = {
-	.flags = IMXUART_HAVE_RTSCTS,
-};
-
-static const struct mxc_nand_platform_data
-pcm038_nand_board_info __initconst = {
-	.width = 1,
-	.hw_ecc = 1,
-};
-
-static struct platform_device *platform_devices[] __initdata = {
-	&pcm038_nor_mtd_device,
-	&pcm038_sram_mtd_device,
-};
-
-/* On pcm038 there's a sram attached to CS1, we enable the chipselect here and
- * setup other stuffs to access the sram. */
-static void __init pcm038_init_sram(void)
-{
-	__raw_writel(0x0000d843, MX27_IO_ADDRESS(MX27_WEIM_CSCRxU(1)));
-	__raw_writel(0x22252521, MX27_IO_ADDRESS(MX27_WEIM_CSCRxL(1)));
-	__raw_writel(0x22220a00, MX27_IO_ADDRESS(MX27_WEIM_CSCRxA(1)));
-}
-
-static const struct imxi2c_platform_data pcm038_i2c1_data __initconst = {
-	.bitrate = 100000,
-};
-
-static struct at24_platform_data board_eeprom = {
-	.byte_len = 4096,
-	.page_size = 32,
-	.flags = AT24_FLAG_ADDR16,
-};
-
-static struct i2c_board_info pcm038_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("at24", 0x52), /* E0=0, E1=1, E2=0 */
-		.platform_data = &board_eeprom,
-	}, {
-		I2C_BOARD_INFO("pcf8563", 0x51),
-	}, {
-		I2C_BOARD_INFO("lm75", 0x4a),
-	}
-};
-
-static int pcm038_spi_cs[] = {GPIO_PORTD + 28};
-
-static const struct spi_imx_master pcm038_spi0_data __initconst = {
-	.chipselect = pcm038_spi_cs,
-	.num_chipselect = ARRAY_SIZE(pcm038_spi_cs),
-};
-
-static struct regulator_consumer_supply sdhc1_consumers[] = {
-	{
-		.dev_name = "imx21-mmc.1",
-		.supply	= "sdhc_vcc",
-	},
-};
-
-static struct regulator_init_data sdhc1_data = {
-	.constraints = {
-		.min_uV = 3000000,
-		.max_uV = 3400000,
-		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
-			REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
-		.valid_modes_mask = REGULATOR_MODE_NORMAL |
-			REGULATOR_MODE_FAST,
-		.always_on = 0,
-		.boot_on = 0,
-	},
-	.num_consumer_supplies = ARRAY_SIZE(sdhc1_consumers),
-	.consumer_supplies = sdhc1_consumers,
-};
-
-static struct regulator_consumer_supply cam_consumers[] = {
-	{
-		.dev_name = NULL,
-		.supply	= "imx_cam_vcc",
-	},
-};
-
-static struct regulator_init_data cam_data = {
-	.constraints = {
-		.min_uV = 3000000,
-		.max_uV = 3400000,
-		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
-			REGULATOR_CHANGE_MODE | REGULATOR_CHANGE_STATUS,
-		.valid_modes_mask = REGULATOR_MODE_NORMAL |
-			REGULATOR_MODE_FAST,
-		.always_on = 0,
-		.boot_on = 0,
-	},
-	.num_consumer_supplies = ARRAY_SIZE(cam_consumers),
-	.consumer_supplies = cam_consumers,
-};
-
-static struct mc13xxx_regulator_init_data pcm038_regulators[] = {
-	{
-		.id = MC13783_REG_VCAM,
-		.init_data = &cam_data,
-	}, {
-		.id = MC13783_REG_VMMC1,
-		.init_data = &sdhc1_data,
-	},
-};
-
-static struct mc13xxx_platform_data pcm038_pmic = {
-	.regulators = {
-		.regulators = pcm038_regulators,
-		.num_regulators = ARRAY_SIZE(pcm038_regulators),
-	},
-	.flags = MC13XXX_USE_ADC | MC13XXX_USE_TOUCHSCREEN,
-};
-
-static struct spi_board_info pcm038_spi_board_info[] __initdata = {
-	{
-		.modalias = "mc13783",
-		/* irq number is run-time assigned */
-		.max_speed_hz = 300000,
-		.bus_num = 0,
-		.chip_select = 0,
-		.platform_data = &pcm038_pmic,
-		.mode = SPI_CS_HIGH,
-	}
-};
-
-static int pcm038_usbh2_init(struct platform_device *pdev)
-{
-	return mx27_initialize_usb_hw(pdev->id, MXC_EHCI_POWER_PINS_ENABLED |
-			MXC_EHCI_INTERFACE_DIFF_UNI);
-}
-
-static const struct mxc_usbh_platform_data usbh2_pdata __initconst = {
-	.init	= pcm038_usbh2_init,
-	.portsc	= MXC_EHCI_MODE_ULPI,
-};
-
-static void __init pcm038_init(void)
-{
-	imx27_soc_init();
-
-	mxc_gpio_setup_multiple_pins(pcm038_pins, ARRAY_SIZE(pcm038_pins),
-			"PCM038");
-
-	pcm038_init_sram();
-
-	imx27_add_imx_uart0(&uart_pdata);
-	imx27_add_imx_uart1(&uart_pdata);
-	imx27_add_imx_uart2(&uart_pdata);
-
-	mxc_gpio_mode(PE16_AF_OWIRE);
-	imx27_add_mxc_nand(&pcm038_nand_board_info);
-
-	/* only the i2c master 1 is used on this CPU card */
-	i2c_register_board_info(1, pcm038_i2c_devices,
-				ARRAY_SIZE(pcm038_i2c_devices));
-
-	imx27_add_imx_i2c(1, &pcm038_i2c1_data);
-
-	/* PE18 for user-LED D40 */
-	mxc_gpio_mode(GPIO_PORTE | 18 | GPIO_GPIO | GPIO_OUT);
-
-	mxc_gpio_mode(GPIO_PORTD | 28 | GPIO_GPIO | GPIO_OUT);
-
-	/* MC13783 IRQ */
-	mxc_gpio_mode(GPIO_PORTB | 23 | GPIO_GPIO | GPIO_IN);
-
-	imx27_add_spi_imx0(&pcm038_spi0_data);
-	pcm038_spi_board_info[0].irq = gpio_to_irq(IMX_GPIO_NR(2, 23));
-	spi_register_board_info(pcm038_spi_board_info,
-				ARRAY_SIZE(pcm038_spi_board_info));
-
-	imx27_add_mxc_ehci_hs(2, &usbh2_pdata);
-
-	imx27_add_fec(NULL);
-	platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
-	imx27_add_imx2_wdt();
-	imx27_add_mxc_w1();
-
-#ifdef CONFIG_MACH_PCM970_BASEBOARD
-	pcm970_baseboard_init();
-#endif
-}
-
-static void __init pcm038_timer_init(void)
-{
-	mx27_clocks_init(26000000);
-}
-
-MACHINE_START(PCM038, "phyCORE-i.MX27")
-	.atag_offset = 0x100,
-	.map_io = mx27_map_io,
-	.init_early = imx27_init_early,
-	.init_irq = mx27_init_irq,
-	.init_time	= pcm038_timer_init,
-	.init_machine = pcm038_init,
-	.restart	= mxc_restart,
-MACHINE_END
diff --git a/arch/arm/mach-imx/pcm970-baseboard.c b/arch/arm/mach-imx/pcm970-baseboard.c
deleted file mode 100644
index 51c6082..0000000
--- a/arch/arm/mach-imx/pcm970-baseboard.c
+++ /dev/null
@@ -1,231 +0,0 @@ 
-/*
- * Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de)
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301, USA.
- */
-
-#include <linux/gpio.h>
-#include <linux/irq.h>
-#include <linux/platform_device.h>
-#include <linux/can/platform/sja1000.h>
-
-#include <asm/mach/arch.h>
-
-#include "common.h"
-#include "devices-imx27.h"
-#include "hardware.h"
-#include "iomux-mx27.h"
-
-static const int pcm970_pins[] __initconst = {
-	/* SDHC */
-	PB4_PF_SD2_D0,
-	PB5_PF_SD2_D1,
-	PB6_PF_SD2_D2,
-	PB7_PF_SD2_D3,
-	PB8_PF_SD2_CMD,
-	PB9_PF_SD2_CLK,
-	/* display */
-	PA5_PF_LSCLK,
-	PA6_PF_LD0,
-	PA7_PF_LD1,
-	PA8_PF_LD2,
-	PA9_PF_LD3,
-	PA10_PF_LD4,
-	PA11_PF_LD5,
-	PA12_PF_LD6,
-	PA13_PF_LD7,
-	PA14_PF_LD8,
-	PA15_PF_LD9,
-	PA16_PF_LD10,
-	PA17_PF_LD11,
-	PA18_PF_LD12,
-	PA19_PF_LD13,
-	PA20_PF_LD14,
-	PA21_PF_LD15,
-	PA22_PF_LD16,
-	PA23_PF_LD17,
-	PA24_PF_REV,
-	PA25_PF_CLS,
-	PA26_PF_PS,
-	PA27_PF_SPL_SPR,
-	PA28_PF_HSYNC,
-	PA29_PF_VSYNC,
-	PA30_PF_CONTRAST,
-	PA31_PF_OE_ACD,
-	/*
-	 * it seems the data line misses a pullup, so we must enable
-	 * the internal pullup as a local workaround
-	 */
-	PD17_PF_I2C_DATA | GPIO_PUEN,
-	PD18_PF_I2C_CLK,
-	/* Camera */
-	PB10_PF_CSI_D0,
-	PB11_PF_CSI_D1,
-	PB12_PF_CSI_D2,
-	PB13_PF_CSI_D3,
-	PB14_PF_CSI_D4,
-	PB15_PF_CSI_MCLK,
-	PB16_PF_CSI_PIXCLK,
-	PB17_PF_CSI_D5,
-	PB18_PF_CSI_D6,
-	PB19_PF_CSI_D7,
-	PB20_PF_CSI_VSYNC,
-	PB21_PF_CSI_HSYNC,
-};
-
-static int pcm970_sdhc2_get_ro(struct device *dev)
-{
-	return gpio_get_value(GPIO_PORTC + 28);
-}
-
-static int pcm970_sdhc2_init(struct device *dev, irq_handler_t detect_irq, void *data)
-{
-	int ret;
-
-	ret = request_irq(gpio_to_irq(IMX_GPIO_NR(3, 29)), detect_irq,
-			  IRQF_TRIGGER_FALLING, "imx-mmc-detect", data);
-	if (ret)
-		return ret;
-
-	ret = gpio_request(GPIO_PORTC + 28, "imx-mmc-ro");
-	if (ret) {
-		free_irq(gpio_to_irq(IMX_GPIO_NR(3, 29)), data);
-		return ret;
-	}
-
-	gpio_direction_input(GPIO_PORTC + 28);
-
-	return 0;
-}
-
-static void pcm970_sdhc2_exit(struct device *dev, void *data)
-{
-	free_irq(gpio_to_irq(IMX_GPIO_NR(3, 29)), data);
-	gpio_free(GPIO_PORTC + 28);
-}
-
-static const struct imxmmc_platform_data sdhc_pdata __initconst = {
-	.get_ro = pcm970_sdhc2_get_ro,
-	.init = pcm970_sdhc2_init,
-	.exit = pcm970_sdhc2_exit,
-};
-
-static struct imx_fb_videomode pcm970_modes[] = {
-	{
-		.mode = {
-			.name		= "Sharp-LQ035Q7",
-			.refresh	= 60,
-			.xres		= 240,
-			.yres		= 320,
-			.pixclock	= 188679, /* in ps (5.3MHz) */
-			.hsync_len	= 7,
-			.left_margin	= 5,
-			.right_margin	= 16,
-			.vsync_len	= 1,
-			.upper_margin	= 7,
-			.lower_margin	= 9,
-		},
-		/*
-		 * - HSYNC active high
-		 * - VSYNC active high
-		 * - clk notenabled while idle
-		 * - clock not inverted
-		 * - data not inverted
-		 * - data enable low active
-		 * - enable sharp mode
-		 */
-		.pcr		= 0xF00080C0,
-		.bpp		= 16,
-	}, {
-		.mode = {
-			.name		= "TX090",
-			.refresh	= 60,
-			.xres		= 240,
-			.yres		= 320,
-			.pixclock	= 38255,
-			.left_margin	= 144,
-			.right_margin	= 0,
-			.upper_margin	= 7,
-			.lower_margin	= 40,
-			.hsync_len	= 96,
-			.vsync_len	= 1,
-		},
-		/*
-		 * - HSYNC active low (1 << 22)
-		 * - VSYNC active low (1 << 23)
-		 * - clk notenabled while idle
-		 * - clock not inverted
-		 * - data not inverted
-		 * - data enable low active
-		 * - enable sharp mode
-		 */
-		.pcr = 0xF0008080 | (1<<22) | (1<<23) | (1<<19),
-		.bpp = 32,
-	},
-};
-
-static const struct imx_fb_platform_data pcm038_fb_data __initconst = {
-	.mode = pcm970_modes,
-	.num_modes = ARRAY_SIZE(pcm970_modes),
-
-	.pwmr		= 0x00A903FF,
-	.lscr1		= 0x00120300,
-	.dmacr		= 0x00020010,
-};
-
-static struct resource pcm970_sja1000_resources[] = {
-	{
-		.start   = MX27_CS4_BASE_ADDR,
-		.end     = MX27_CS4_BASE_ADDR + 0x100 - 1,
-		.flags   = IORESOURCE_MEM,
-	}, {
-		/* irq number is run-time assigned */
-		.flags   = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
-	},
-};
-
-static struct sja1000_platform_data pcm970_sja1000_platform_data = {
-	.osc_freq	= 16000000,
-	.ocr		= OCR_TX1_PULLDOWN | OCR_TX0_PUSHPULL,
-	.cdr		= CDR_CBP,
-};
-
-static struct platform_device pcm970_sja1000 = {
-	.name = "sja1000_platform",
-	.dev = {
-		.platform_data = &pcm970_sja1000_platform_data,
-	},
-	.resource = pcm970_sja1000_resources,
-	.num_resources = ARRAY_SIZE(pcm970_sja1000_resources),
-};
-
-/*
- * system init for baseboard usage. Will be called by pcm038 init.
- *
- * Add platform devices present on this baseboard and init
- * them from CPU side as far as required to use them later on
- */
-void __init pcm970_baseboard_init(void)
-{
-	mxc_gpio_setup_multiple_pins(pcm970_pins, ARRAY_SIZE(pcm970_pins),
-			"PCM970");
-
-	imx27_add_imx_fb(&pcm038_fb_data);
-	mxc_gpio_mode(GPIO_PORTC | 28 | GPIO_GPIO | GPIO_IN);
-	imx27_add_mxc_mmc(1, &sdhc_pdata);
-	pcm970_sja1000_resources[1].start = gpio_to_irq(IMX_GPIO_NR(5, 19));
-	pcm970_sja1000_resources[1].end = gpio_to_irq(IMX_GPIO_NR(5, 19));
-	platform_device_register(&pcm970_sja1000);
-}