diff mbox

[v4,4/4] pinctrl: qcom: Make the target processor value configurable

Message ID 1409761696-15435-5-git-send-email-gdjakov@mm-sol.com (mailing list archive)
State New, archived
Headers show

Commit Message

Georgi Djakov Sept. 3, 2014, 4:28 p.m. UTC 
Currently the value used to specify that interrupts from the gpio should
be routed to the application processor is hardcoded for all Qualcomm SoCs.
But the new APQ8084 SoC uses a different value. To resolve this, we make
this value configurable for each SoC. For all existing SoCs we continue
to use the current value, and only for APQ8084 we use the new value.

Suggested-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
---
 drivers/pinctrl/qcom/pinctrl-apq8064.c |    2 ++
 drivers/pinctrl/qcom/pinctrl-apq8084.c |    2 ++
 drivers/pinctrl/qcom/pinctrl-ipq8064.c |    2 ++
 drivers/pinctrl/qcom/pinctrl-msm.c     |    4 +---
 drivers/pinctrl/qcom/pinctrl-msm.h     |    3 +++
 drivers/pinctrl/qcom/pinctrl-msm8960.c |    2 ++
 drivers/pinctrl/qcom/pinctrl-msm8x74.c |    2 ++
 7 files changed, 14 insertions(+), 3 deletions(-)

Comments

Linus Walleij Sept. 4, 2014, 4:20 p.m. UTC | #1 
On Wed, Sep 3, 2014 at 6:28 PM, Georgi Djakov <gdjakov@mm-sol.com> wrote:

> Currently the value used to specify that interrupts from the gpio should
> be routed to the application processor is hardcoded for all Qualcomm SoCs.
> But the new APQ8084 SoC uses a different value. To resolve this, we make
> this value configurable for each SoC. For all existing SoCs we continue
> to use the current value, and only for APQ8084 we use the new value.
>
> Suggested-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
> Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
> Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>

Patch applied.

Yours,
Linus Walleij
Georgi Djakov Sept. 5, 2014, 7:20 a.m. UTC | #2 
On 09/04/2014 07:20 PM, Linus Walleij wrote:
> On Wed, Sep 3, 2014 at 6:28 PM, Georgi Djakov <gdjakov@mm-sol.com> wrote:
> 
>> Currently the value used to specify that interrupts from the gpio should
>> be routed to the application processor is hardcoded for all Qualcomm SoCs.
>> But the new APQ8084 SoC uses a different value. To resolve this, we make
>> this value configurable for each SoC. For all existing SoCs we continue
>> to use the current value, and only for APQ8084 we use the new value.
>>
>> Suggested-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
>> Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
>> Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
> 
> Patch applied.
> 
> Yours,
> Linus Walleij
> 

Thank you, Bjorn and Linus!
diff mbox

Patch

diff --git a/drivers/pinctrl/qcom/pinctrl-apq8064.c b/drivers/pinctrl/qcom/pinctrl-apq8064.c
index feb6f15..f877aed 100644
--- a/drivers/pinctrl/qcom/pinctrl-apq8064.c
+++ b/drivers/pinctrl/qcom/pinctrl-apq8064.c
@@ -258,6 +258,7 @@  static const unsigned int sdc3_data_pins[] = { 95 };
 		.intr_status_bit = 0,			\
 		.intr_ack_high = 1,			\
 		.intr_target_bit = 0,			\
+		.intr_target_kpss_val = 4,		\
 		.intr_raw_status_bit = 3,		\
 		.intr_polarity_bit = 1,			\
 		.intr_detection_bit = 2,		\
@@ -283,6 +284,7 @@  static const unsigned int sdc3_data_pins[] = { 95 };
 		.intr_enable_bit = -1,			\
 		.intr_status_bit = -1,			\
 		.intr_target_bit = -1,			\
+		.intr_target_kpss_val = -1,		\
 		.intr_raw_status_bit = -1,		\
 		.intr_polarity_bit = -1,		\
 		.intr_detection_bit = -1,		\
diff --git a/drivers/pinctrl/qcom/pinctrl-apq8084.c b/drivers/pinctrl/qcom/pinctrl-apq8084.c
index 5362959..138cbf6 100644
--- a/drivers/pinctrl/qcom/pinctrl-apq8084.c
+++ b/drivers/pinctrl/qcom/pinctrl-apq8084.c
@@ -371,6 +371,7 @@  static const unsigned int sdc2_data_pins[] = { 152 };
 		.intr_status_bit = 0,			\
 		.intr_ack_high = 0,			\
 		.intr_target_bit = 5,			\
+		.intr_target_kpss_val = 3,		\
 		.intr_raw_status_bit = 4,		\
 		.intr_polarity_bit = 1,			\
 		.intr_detection_bit = 2,		\
@@ -396,6 +397,7 @@  static const unsigned int sdc2_data_pins[] = { 152 };
 		.intr_enable_bit = -1,                  \
 		.intr_status_bit = -1,                  \
 		.intr_target_bit = -1,                  \
+		.intr_target_kpss_val = -1,		\
 		.intr_raw_status_bit = -1,              \
 		.intr_polarity_bit = -1,                \
 		.intr_detection_bit = -1,               \
diff --git a/drivers/pinctrl/qcom/pinctrl-ipq8064.c b/drivers/pinctrl/qcom/pinctrl-ipq8064.c
index 767cf11..81f49a9 100644
--- a/drivers/pinctrl/qcom/pinctrl-ipq8064.c
+++ b/drivers/pinctrl/qcom/pinctrl-ipq8064.c
@@ -211,6 +211,7 @@  static const unsigned int sdc3_data_pins[] = { 71 };
 		.intr_status_bit = 0,			\
 		.intr_ack_high = 1,			\
 		.intr_target_bit = 0,			\
+		.intr_target_kpss_val = 4,		\
 		.intr_raw_status_bit = 3,		\
 		.intr_polarity_bit = 1,			\
 		.intr_detection_bit = 2,		\
@@ -236,6 +237,7 @@  static const unsigned int sdc3_data_pins[] = { 71 };
 		.intr_enable_bit = -1,                  \
 		.intr_status_bit = -1,                  \
 		.intr_target_bit = -1,                  \
+		.intr_target_kpss_val = -1,		\
 		.intr_raw_status_bit = -1,              \
 		.intr_polarity_bit = -1,                \
 		.intr_detection_bit = -1,               \
diff --git a/drivers/pinctrl/qcom/pinctrl-msm.c b/drivers/pinctrl/qcom/pinctrl-msm.c
index 2738108..592c6fc 100644
--- a/drivers/pinctrl/qcom/pinctrl-msm.c
+++ b/drivers/pinctrl/qcom/pinctrl-msm.c
@@ -649,8 +649,6 @@  static void msm_gpio_irq_ack(struct irq_data *d)
 	spin_unlock_irqrestore(&pctrl->lock, flags);
 }
 
-#define INTR_TARGET_PROC_APPS    4
-
 static int msm_gpio_irq_set_type(struct irq_data *d, unsigned int type)
 {
 	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
@@ -674,7 +672,7 @@  static int msm_gpio_irq_set_type(struct irq_data *d, unsigned int type)
 	/* Route interrupts to application cpu */
 	val = readl(pctrl->regs + g->intr_target_reg);
 	val &= ~(7 << g->intr_target_bit);
-	val |= INTR_TARGET_PROC_APPS << g->intr_target_bit;
+	val |= g->intr_target_kpss_val << g->intr_target_bit;
 	writel(val, pctrl->regs + g->intr_target_reg);
 
 	/* Update configuration for gpio.
diff --git a/drivers/pinctrl/qcom/pinctrl-msm.h b/drivers/pinctrl/qcom/pinctrl-msm.h
index 7b2a227..b952c4b 100644
--- a/drivers/pinctrl/qcom/pinctrl-msm.h
+++ b/drivers/pinctrl/qcom/pinctrl-msm.h
@@ -53,6 +53,8 @@  struct msm_function {
  * @intr_status_bit:      Offset in @intr_status_reg for reading and acking the interrupt
  *                        status.
  * @intr_target_bit:      Offset in @intr_target_reg for configuring the interrupt routing.
+ * @intr_target_kpss_val: Value in @intr_target_bit for specifying that the interrupt from
+ *                        this gpio should get routed to the KPSS processor.
  * @intr_raw_status_bit:  Offset in @intr_cfg_reg for the raw status bit.
  * @intr_polarity_bit:    Offset in @intr_cfg_reg for specifying polarity of the interrupt.
  * @intr_detection_bit:   Offset in @intr_cfg_reg for specifying interrupt type.
@@ -88,6 +90,7 @@  struct msm_pingroup {
 	unsigned intr_ack_high:1;
 
 	unsigned intr_target_bit:5;
+	unsigned intr_target_kpss_val:5;
 	unsigned intr_raw_status_bit:5;
 	unsigned intr_polarity_bit:5;
 	unsigned intr_detection_bit:5;
diff --git a/drivers/pinctrl/qcom/pinctrl-msm8960.c b/drivers/pinctrl/qcom/pinctrl-msm8960.c
index 3504703..2ab21ce 100644
--- a/drivers/pinctrl/qcom/pinctrl-msm8960.c
+++ b/drivers/pinctrl/qcom/pinctrl-msm8960.c
@@ -384,6 +384,7 @@  static const unsigned int sdc3_data_pins[] = { 157 };
 		.intr_status_bit = 0,			\
 		.intr_ack_high = 1,			\
 		.intr_target_bit = 0,			\
+		.intr_target_kpss_val = 4,		\
 		.intr_raw_status_bit = 3,		\
 		.intr_polarity_bit = 1,			\
 		.intr_detection_bit = 2,		\
@@ -409,6 +410,7 @@  static const unsigned int sdc3_data_pins[] = { 157 };
 		.intr_enable_bit = -1,			\
 		.intr_status_bit = -1,			\
 		.intr_target_bit = -1,			\
+		.intr_target_kpss_val = -1,		\
 		.intr_raw_status_bit = -1,		\
 		.intr_polarity_bit = -1,		\
 		.intr_detection_bit = -1,		\
diff --git a/drivers/pinctrl/qcom/pinctrl-msm8x74.c b/drivers/pinctrl/qcom/pinctrl-msm8x74.c
index 8c97201..3c85838 100644
--- a/drivers/pinctrl/qcom/pinctrl-msm8x74.c
+++ b/drivers/pinctrl/qcom/pinctrl-msm8x74.c
@@ -366,6 +366,7 @@  static const unsigned int sdc2_data_pins[] = { 151 };
 		.intr_enable_bit = 0,			\
 		.intr_status_bit = 0,			\
 		.intr_target_bit = 5,			\
+		.intr_target_kpss_val = 4,		\
 		.intr_raw_status_bit = 4,		\
 		.intr_polarity_bit = 1,			\
 		.intr_detection_bit = 2,		\
@@ -391,6 +392,7 @@  static const unsigned int sdc2_data_pins[] = { 151 };
 		.intr_enable_bit = -1,			\
 		.intr_status_bit = -1,			\
 		.intr_target_bit = -1,			\
+		.intr_target_kpss_val = -1,		\
 		.intr_raw_status_bit = -1,		\
 		.intr_polarity_bit = -1,		\
 		.intr_detection_bit = -1,		\