diff mbox

ARM: at91: board file for Acme Systems Fox G20

Message ID 1410787655-28263-1-git-send-email-nicolas.ferre@atmel.com (mailing list archive)
State New, archived
Headers show

Commit Message

Nicolas Ferre Sept. 15, 2014, 1:27 p.m. UTC
As Acme Systems Fox G20 is available in Device Tree flavor and that we plan to
remove all the board files soon, we can remove this one without problem.
If you use this board, please use a DT-enabled at91sam9g20 kernel with
at91-foxg20.dts.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
---
 arch/arm/mach-at91/Kconfig.non_dt |   6 -
 arch/arm/mach-at91/Makefile       |   1 -
 arch/arm/mach-at91/board-foxg20.c | 272 --------------------------------------
 3 files changed, 279 deletions(-)
 delete mode 100644 arch/arm/mach-at91/board-foxg20.c

Comments

Nicolas Ferre Sept. 15, 2014, 1:30 p.m. UTC | #1
I should have added a little "remove" in the subject: already corrected
in my tree...

On 15/09/2014 15:27, Nicolas Ferre :
> As Acme Systems Fox G20 is available in Device Tree flavor and that we plan to
> remove all the board files soon, we can remove this one without problem.
> If you use this board, please use a DT-enabled at91sam9g20 kernel with
> at91-foxg20.dts.
> 
> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
> ---
>  arch/arm/mach-at91/Kconfig.non_dt |   6 -
>  arch/arm/mach-at91/Makefile       |   1 -
>  arch/arm/mach-at91/board-foxg20.c | 272 --------------------------------------
>  3 files changed, 279 deletions(-)
>  delete mode 100644 arch/arm/mach-at91/board-foxg20.c
> 
> diff --git a/arch/arm/mach-at91/Kconfig.non_dt b/arch/arm/mach-at91/Kconfig.non_dt
> index 44ace320d2e1..a2ee352a8904 100644
> --- a/arch/arm/mach-at91/Kconfig.non_dt
> +++ b/arch/arm/mach-at91/Kconfig.non_dt
> @@ -212,12 +212,6 @@ config MACH_CPU9G20
>  	  Select this if you are using a Eukrea Electromatique's
>  	  CPU9G20 Board <http://www.eukrea.com/>
>  
> -config MACH_ACMENETUSFOXG20
> -	bool "Acme Systems srl FOX Board G20"
> -	help
> -	  Select this if you are using Acme Systems
> -	  FOX Board G20 <http://www.acmesystems.it>
> -
>  config MACH_PORTUXG20
>  	bool "taskit PortuxG20"
>  	help
> diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
> index 78e9cec282f4..e8efcb00ca94 100644
> --- a/arch/arm/mach-at91/Makefile
> +++ b/arch/arm/mach-at91/Makefile
> @@ -69,7 +69,6 @@ obj-$(CONFIG_MACH_AT91SAM9RLEK)	+= board-sam9rlek.o
>  # AT91SAM9G20 board-specific support
>  obj-$(CONFIG_MACH_AT91SAM9G20EK) += board-sam9g20ek.o
>  obj-$(CONFIG_MACH_CPU9G20)	+= board-cpu9krea.o
> -obj-$(CONFIG_MACH_ACMENETUSFOXG20) += board-foxg20.o
>  obj-$(CONFIG_MACH_STAMP9G20)	+= board-stamp9g20.o
>  obj-$(CONFIG_MACH_PORTUXG20)	+= board-stamp9g20.o
>  obj-$(CONFIG_MACH_PCONTROL_G20)	+= board-pcontrol-g20.o board-stamp9g20.o
> diff --git a/arch/arm/mach-at91/board-foxg20.c b/arch/arm/mach-at91/board-foxg20.c
> deleted file mode 100644
> index 8b22c60bb238..000000000000
> --- a/arch/arm/mach-at91/board-foxg20.c
> +++ /dev/null
> @@ -1,272 +0,0 @@
> -/*
> - *  Copyright (C) 2005 SAN People
> - *  Copyright (C) 2008 Atmel
> - *  Copyright (C) 2010 Lee McLoughlin - lee@lmmrtech.com
> - *  Copyright (C) 2010 Sergio Tanzilli - tanzilli@acmesystems.it
> - *
> - * This program is free software; you can redistribute it and/or modify
> - * it under the terms of the GNU General Public License as published by
> - * the Free Software Foundation; either version 2 of the License, or
> - * (at your option) any later version.
> - *
> - * This program is distributed in the hope that it will be useful,
> - * but WITHOUT ANY WARRANTY; without even the implied warranty of
> - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> - * GNU General Public License for more details.
> - *
> - * You should have received a copy of the GNU General Public License
> - * along with this program; if not, write to the Free Software
> - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
> - */
> -
> -#include <linux/types.h>
> -#include <linux/init.h>
> -#include <linux/mm.h>
> -#include <linux/module.h>
> -#include <linux/platform_device.h>
> -#include <linux/spi/spi.h>
> -#include <linux/spi/at73c213.h>
> -#include <linux/gpio.h>
> -#include <linux/gpio_keys.h>
> -#include <linux/input.h>
> -#include <linux/clk.h>
> -#include <linux/w1-gpio.h>
> -
> -#include <mach/hardware.h>
> -#include <asm/setup.h>
> -#include <asm/mach-types.h>
> -#include <asm/irq.h>
> -
> -#include <asm/mach/arch.h>
> -#include <asm/mach/map.h>
> -#include <asm/mach/irq.h>
> -
> -#include <mach/at91sam9_smc.h>
> -
> -#include "at91_aic.h"
> -#include "board.h"
> -#include "sam9_smc.h"
> -#include "generic.h"
> -#include "gpio.h"
> -
> -/*
> - * The FOX Board G20 hardware comes as the "Netus G20" board with
> - * just the cpu, ram, dataflash and two header connectors.
> - * This is plugged into the FOX Board which provides the ethernet,
> - * usb, rtc, leds, switch, ...
> - *
> - * For more info visit: http://www.acmesystems.it/foxg20
> - */
> -
> -
> -static void __init foxg20_init_early(void)
> -{
> -	/* Initialize processor: 18.432 MHz crystal */
> -	at91_initialize(18432000);
> -}
> -
> -/*
> - * USB Host port
> - */
> -static struct at91_usbh_data __initdata foxg20_usbh_data = {
> -	.ports		= 2,
> -	.vbus_pin	= {-EINVAL, -EINVAL},
> -	.overcurrent_pin= {-EINVAL, -EINVAL},
> -};
> -
> -/*
> - * USB Device port
> - */
> -static struct at91_udc_data __initdata foxg20_udc_data = {
> -	.vbus_pin	= AT91_PIN_PC6,
> -	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
> -};
> -
> -
> -/*
> - * SPI devices.
> - */
> -static struct spi_board_info foxg20_spi_devices[] = {
> -#if !IS_ENABLED(CONFIG_MMC_ATMELMCI)
> -	{
> -		.modalias	= "mtd_dataflash",
> -		.chip_select	= 1,
> -		.max_speed_hz	= 15 * 1000 * 1000,
> -		.bus_num	= 0,
> -	},
> -#endif
> -};
> -
> -
> -/*
> - * MACB Ethernet device
> - */
> -static struct macb_platform_data __initdata foxg20_macb_data = {
> -	.phy_irq_pin	= AT91_PIN_PA7,
> -	.is_rmii	= 1,
> -};
> -
> -/*
> - * MCI (SD/MMC)
> - * det_pin, wp_pin and vcc_pin are not connected
> - */
> -static struct mci_platform_data __initdata foxg20_mci0_data = {
> -	.slot[1] = {
> -		.bus_width	= 4,
> -		.detect_pin	= -EINVAL,
> -		.wp_pin		= -EINVAL,
> -	},
> -};
> -
> -
> -/*
> - * LEDs
> - */
> -static struct gpio_led foxg20_leds[] = {
> -	{	/* user led, red */
> -		.name			= "user_led",
> -		.gpio			= AT91_PIN_PC7,
> -		.active_low		= 0,
> -		.default_trigger	= "heartbeat",
> -	},
> -};
> -
> -
> -/*
> - * GPIO Buttons
> - */
> -#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
> -static struct gpio_keys_button foxg20_buttons[] = {
> -	{
> -		.gpio		= AT91_PIN_PC4,
> -		.code		= BTN_1,
> -		.desc		= "Button 1",
> -		.active_low	= 1,
> -		.wakeup		= 1,
> -	},
> -};
> -
> -static struct gpio_keys_platform_data foxg20_button_data = {
> -	.buttons	= foxg20_buttons,
> -	.nbuttons	= ARRAY_SIZE(foxg20_buttons),
> -};
> -
> -static struct platform_device foxg20_button_device = {
> -	.name		= "gpio-keys",
> -	.id		= -1,
> -	.num_resources	= 0,
> -	.dev		= {
> -		.platform_data	= &foxg20_button_data,
> -	}
> -};
> -
> -static void __init foxg20_add_device_buttons(void)
> -{
> -	at91_set_gpio_input(AT91_PIN_PC4, 1);	/* btn1 */
> -	at91_set_deglitch(AT91_PIN_PC4, 1);
> -
> -	platform_device_register(&foxg20_button_device);
> -}
> -#else
> -static void __init foxg20_add_device_buttons(void) {}
> -#endif
> -
> -
> -#if defined(CONFIG_W1_MASTER_GPIO) || defined(CONFIG_W1_MASTER_GPIO_MODULE)
> -static struct w1_gpio_platform_data w1_gpio_pdata = {
> -	/* If you choose to use a pin other than PB16 it needs to be 3.3V */
> -	.pin		= AT91_PIN_PB16,
> -	.is_open_drain  = 1,
> -	.ext_pullup_enable_pin	= -EINVAL,
> -};
> -
> -static struct platform_device w1_device = {
> -	.name			= "w1-gpio",
> -	.id			= -1,
> -	.dev.platform_data	= &w1_gpio_pdata,
> -};
> -
> -static void __init at91_add_device_w1(void)
> -{
> -	at91_set_GPIO_periph(w1_gpio_pdata.pin, 1);
> -	at91_set_multi_drive(w1_gpio_pdata.pin, 1);
> -	platform_device_register(&w1_device);
> -}
> -
> -#endif
> -
> -
> -static struct i2c_board_info __initdata foxg20_i2c_devices[] = {
> -	{
> -		I2C_BOARD_INFO("24c512", 0x50),
> -	},
> -};
> -
> -
> -static void __init foxg20_board_init(void)
> -{
> -	/* Serial */
> -	/* DBGU on ttyS0. (Rx & Tx only) */
> -	at91_register_uart(0, 0, 0);
> -
> -	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
> -	at91_register_uart(AT91SAM9260_ID_US0, 1,
> -				ATMEL_UART_CTS
> -				| ATMEL_UART_RTS
> -				| ATMEL_UART_DTR
> -				| ATMEL_UART_DSR
> -				| ATMEL_UART_DCD
> -				| ATMEL_UART_RI);
> -
> -	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
> -	at91_register_uart(AT91SAM9260_ID_US1, 2,
> -		ATMEL_UART_CTS
> -		| ATMEL_UART_RTS);
> -
> -	/* USART2 on ttyS3. (Rx & Tx only) */
> -	at91_register_uart(AT91SAM9260_ID_US2, 3, 0);
> -
> -	/* USART3 on ttyS4. (Rx, Tx, RTS, CTS) */
> -	at91_register_uart(AT91SAM9260_ID_US3, 4,
> -		ATMEL_UART_CTS
> -		| ATMEL_UART_RTS);
> -
> -	/* USART4 on ttyS5. (Rx & Tx only) */
> -	at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
> -
> -	/* USART5 on ttyS6. (Rx & Tx only) */
> -	at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
> -
> -	/* Set the internal pull-up resistor on DRXD */
> -	at91_set_A_periph(AT91_PIN_PB14, 1);
> -	at91_add_device_serial();
> -	/* USB Host */
> -	at91_add_device_usbh(&foxg20_usbh_data);
> -	/* USB Device */
> -	at91_add_device_udc(&foxg20_udc_data);
> -	/* SPI */
> -	at91_add_device_spi(foxg20_spi_devices, ARRAY_SIZE(foxg20_spi_devices));
> -	/* Ethernet */
> -	at91_add_device_eth(&foxg20_macb_data);
> -	/* MMC */
> -	at91_add_device_mci(0, &foxg20_mci0_data);
> -	/* I2C */
> -	at91_add_device_i2c(foxg20_i2c_devices, ARRAY_SIZE(foxg20_i2c_devices));
> -	/* LEDs */
> -	at91_gpio_leds(foxg20_leds, ARRAY_SIZE(foxg20_leds));
> -	/* Push Buttons */
> -	foxg20_add_device_buttons();
> -#if defined(CONFIG_W1_MASTER_GPIO) || defined(CONFIG_W1_MASTER_GPIO_MODULE)
> -	at91_add_device_w1();
> -#endif
> -}
> -
> -MACHINE_START(ACMENETUSFOXG20, "Acme Systems srl FOX Board G20")
> -	/* Maintainer: Sergio Tanzilli */
> -	.init_time	= at91sam926x_pit_init,
> -	.map_io		= at91_map_io,
> -	.handle_irq	= at91_aic_handle_irq,
> -	.init_early	= foxg20_init_early,
> -	.init_irq	= at91_init_irq_default,
> -	.init_machine	= foxg20_board_init,
> -MACHINE_END
>
Nicolas Ferre Sept. 16, 2014, 4:39 p.m. UTC | #2
On 15/09/2014 15:27, Nicolas Ferre :
> As Acme Systems Fox G20 is available in Device Tree flavor and that we plan to
> remove all the board files soon, we can remove this one without problem.
> If you use this board, please use a DT-enabled at91sam9g20 kernel with
> at91-foxg20.dts.
> 
> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

I've just got the Ack from Sergio in private, so we can add:

Acked-by: Sergio Tanzilli <tanzilli@acmesystems.it>

Bye,

> ---
>  arch/arm/mach-at91/Kconfig.non_dt |   6 -
>  arch/arm/mach-at91/Makefile       |   1 -
>  arch/arm/mach-at91/board-foxg20.c | 272 --------------------------------------
>  3 files changed, 279 deletions(-)
>  delete mode 100644 arch/arm/mach-at91/board-foxg20.c
> 
> diff --git a/arch/arm/mach-at91/Kconfig.non_dt b/arch/arm/mach-at91/Kconfig.non_dt
> index 44ace320d2e1..a2ee352a8904 100644
> --- a/arch/arm/mach-at91/Kconfig.non_dt
> +++ b/arch/arm/mach-at91/Kconfig.non_dt
> @@ -212,12 +212,6 @@ config MACH_CPU9G20
>  	  Select this if you are using a Eukrea Electromatique's
>  	  CPU9G20 Board <http://www.eukrea.com/>
>  
> -config MACH_ACMENETUSFOXG20
> -	bool "Acme Systems srl FOX Board G20"
> -	help
> -	  Select this if you are using Acme Systems
> -	  FOX Board G20 <http://www.acmesystems.it>
> -
>  config MACH_PORTUXG20
>  	bool "taskit PortuxG20"
>  	help
> diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
> index 78e9cec282f4..e8efcb00ca94 100644
> --- a/arch/arm/mach-at91/Makefile
> +++ b/arch/arm/mach-at91/Makefile
> @@ -69,7 +69,6 @@ obj-$(CONFIG_MACH_AT91SAM9RLEK)	+= board-sam9rlek.o
>  # AT91SAM9G20 board-specific support
>  obj-$(CONFIG_MACH_AT91SAM9G20EK) += board-sam9g20ek.o
>  obj-$(CONFIG_MACH_CPU9G20)	+= board-cpu9krea.o
> -obj-$(CONFIG_MACH_ACMENETUSFOXG20) += board-foxg20.o
>  obj-$(CONFIG_MACH_STAMP9G20)	+= board-stamp9g20.o
>  obj-$(CONFIG_MACH_PORTUXG20)	+= board-stamp9g20.o
>  obj-$(CONFIG_MACH_PCONTROL_G20)	+= board-pcontrol-g20.o board-stamp9g20.o
> diff --git a/arch/arm/mach-at91/board-foxg20.c b/arch/arm/mach-at91/board-foxg20.c
> deleted file mode 100644
> index 8b22c60bb238..000000000000
> --- a/arch/arm/mach-at91/board-foxg20.c
> +++ /dev/null
> @@ -1,272 +0,0 @@
> -/*
> - *  Copyright (C) 2005 SAN People
> - *  Copyright (C) 2008 Atmel
> - *  Copyright (C) 2010 Lee McLoughlin - lee@lmmrtech.com
> - *  Copyright (C) 2010 Sergio Tanzilli - tanzilli@acmesystems.it
> - *
> - * This program is free software; you can redistribute it and/or modify
> - * it under the terms of the GNU General Public License as published by
> - * the Free Software Foundation; either version 2 of the License, or
> - * (at your option) any later version.
> - *
> - * This program is distributed in the hope that it will be useful,
> - * but WITHOUT ANY WARRANTY; without even the implied warranty of
> - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> - * GNU General Public License for more details.
> - *
> - * You should have received a copy of the GNU General Public License
> - * along with this program; if not, write to the Free Software
> - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
> - */
> -
> -#include <linux/types.h>
> -#include <linux/init.h>
> -#include <linux/mm.h>
> -#include <linux/module.h>
> -#include <linux/platform_device.h>
> -#include <linux/spi/spi.h>
> -#include <linux/spi/at73c213.h>
> -#include <linux/gpio.h>
> -#include <linux/gpio_keys.h>
> -#include <linux/input.h>
> -#include <linux/clk.h>
> -#include <linux/w1-gpio.h>
> -
> -#include <mach/hardware.h>
> -#include <asm/setup.h>
> -#include <asm/mach-types.h>
> -#include <asm/irq.h>
> -
> -#include <asm/mach/arch.h>
> -#include <asm/mach/map.h>
> -#include <asm/mach/irq.h>
> -
> -#include <mach/at91sam9_smc.h>
> -
> -#include "at91_aic.h"
> -#include "board.h"
> -#include "sam9_smc.h"
> -#include "generic.h"
> -#include "gpio.h"
> -
> -/*
> - * The FOX Board G20 hardware comes as the "Netus G20" board with
> - * just the cpu, ram, dataflash and two header connectors.
> - * This is plugged into the FOX Board which provides the ethernet,
> - * usb, rtc, leds, switch, ...
> - *
> - * For more info visit: http://www.acmesystems.it/foxg20
> - */
> -
> -
> -static void __init foxg20_init_early(void)
> -{
> -	/* Initialize processor: 18.432 MHz crystal */
> -	at91_initialize(18432000);
> -}
> -
> -/*
> - * USB Host port
> - */
> -static struct at91_usbh_data __initdata foxg20_usbh_data = {
> -	.ports		= 2,
> -	.vbus_pin	= {-EINVAL, -EINVAL},
> -	.overcurrent_pin= {-EINVAL, -EINVAL},
> -};
> -
> -/*
> - * USB Device port
> - */
> -static struct at91_udc_data __initdata foxg20_udc_data = {
> -	.vbus_pin	= AT91_PIN_PC6,
> -	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
> -};
> -
> -
> -/*
> - * SPI devices.
> - */
> -static struct spi_board_info foxg20_spi_devices[] = {
> -#if !IS_ENABLED(CONFIG_MMC_ATMELMCI)
> -	{
> -		.modalias	= "mtd_dataflash",
> -		.chip_select	= 1,
> -		.max_speed_hz	= 15 * 1000 * 1000,
> -		.bus_num	= 0,
> -	},
> -#endif
> -};
> -
> -
> -/*
> - * MACB Ethernet device
> - */
> -static struct macb_platform_data __initdata foxg20_macb_data = {
> -	.phy_irq_pin	= AT91_PIN_PA7,
> -	.is_rmii	= 1,
> -};
> -
> -/*
> - * MCI (SD/MMC)
> - * det_pin, wp_pin and vcc_pin are not connected
> - */
> -static struct mci_platform_data __initdata foxg20_mci0_data = {
> -	.slot[1] = {
> -		.bus_width	= 4,
> -		.detect_pin	= -EINVAL,
> -		.wp_pin		= -EINVAL,
> -	},
> -};
> -
> -
> -/*
> - * LEDs
> - */
> -static struct gpio_led foxg20_leds[] = {
> -	{	/* user led, red */
> -		.name			= "user_led",
> -		.gpio			= AT91_PIN_PC7,
> -		.active_low		= 0,
> -		.default_trigger	= "heartbeat",
> -	},
> -};
> -
> -
> -/*
> - * GPIO Buttons
> - */
> -#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
> -static struct gpio_keys_button foxg20_buttons[] = {
> -	{
> -		.gpio		= AT91_PIN_PC4,
> -		.code		= BTN_1,
> -		.desc		= "Button 1",
> -		.active_low	= 1,
> -		.wakeup		= 1,
> -	},
> -};
> -
> -static struct gpio_keys_platform_data foxg20_button_data = {
> -	.buttons	= foxg20_buttons,
> -	.nbuttons	= ARRAY_SIZE(foxg20_buttons),
> -};
> -
> -static struct platform_device foxg20_button_device = {
> -	.name		= "gpio-keys",
> -	.id		= -1,
> -	.num_resources	= 0,
> -	.dev		= {
> -		.platform_data	= &foxg20_button_data,
> -	}
> -};
> -
> -static void __init foxg20_add_device_buttons(void)
> -{
> -	at91_set_gpio_input(AT91_PIN_PC4, 1);	/* btn1 */
> -	at91_set_deglitch(AT91_PIN_PC4, 1);
> -
> -	platform_device_register(&foxg20_button_device);
> -}
> -#else
> -static void __init foxg20_add_device_buttons(void) {}
> -#endif
> -
> -
> -#if defined(CONFIG_W1_MASTER_GPIO) || defined(CONFIG_W1_MASTER_GPIO_MODULE)
> -static struct w1_gpio_platform_data w1_gpio_pdata = {
> -	/* If you choose to use a pin other than PB16 it needs to be 3.3V */
> -	.pin		= AT91_PIN_PB16,
> -	.is_open_drain  = 1,
> -	.ext_pullup_enable_pin	= -EINVAL,
> -};
> -
> -static struct platform_device w1_device = {
> -	.name			= "w1-gpio",
> -	.id			= -1,
> -	.dev.platform_data	= &w1_gpio_pdata,
> -};
> -
> -static void __init at91_add_device_w1(void)
> -{
> -	at91_set_GPIO_periph(w1_gpio_pdata.pin, 1);
> -	at91_set_multi_drive(w1_gpio_pdata.pin, 1);
> -	platform_device_register(&w1_device);
> -}
> -
> -#endif
> -
> -
> -static struct i2c_board_info __initdata foxg20_i2c_devices[] = {
> -	{
> -		I2C_BOARD_INFO("24c512", 0x50),
> -	},
> -};
> -
> -
> -static void __init foxg20_board_init(void)
> -{
> -	/* Serial */
> -	/* DBGU on ttyS0. (Rx & Tx only) */
> -	at91_register_uart(0, 0, 0);
> -
> -	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
> -	at91_register_uart(AT91SAM9260_ID_US0, 1,
> -				ATMEL_UART_CTS
> -				| ATMEL_UART_RTS
> -				| ATMEL_UART_DTR
> -				| ATMEL_UART_DSR
> -				| ATMEL_UART_DCD
> -				| ATMEL_UART_RI);
> -
> -	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
> -	at91_register_uart(AT91SAM9260_ID_US1, 2,
> -		ATMEL_UART_CTS
> -		| ATMEL_UART_RTS);
> -
> -	/* USART2 on ttyS3. (Rx & Tx only) */
> -	at91_register_uart(AT91SAM9260_ID_US2, 3, 0);
> -
> -	/* USART3 on ttyS4. (Rx, Tx, RTS, CTS) */
> -	at91_register_uart(AT91SAM9260_ID_US3, 4,
> -		ATMEL_UART_CTS
> -		| ATMEL_UART_RTS);
> -
> -	/* USART4 on ttyS5. (Rx & Tx only) */
> -	at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
> -
> -	/* USART5 on ttyS6. (Rx & Tx only) */
> -	at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
> -
> -	/* Set the internal pull-up resistor on DRXD */
> -	at91_set_A_periph(AT91_PIN_PB14, 1);
> -	at91_add_device_serial();
> -	/* USB Host */
> -	at91_add_device_usbh(&foxg20_usbh_data);
> -	/* USB Device */
> -	at91_add_device_udc(&foxg20_udc_data);
> -	/* SPI */
> -	at91_add_device_spi(foxg20_spi_devices, ARRAY_SIZE(foxg20_spi_devices));
> -	/* Ethernet */
> -	at91_add_device_eth(&foxg20_macb_data);
> -	/* MMC */
> -	at91_add_device_mci(0, &foxg20_mci0_data);
> -	/* I2C */
> -	at91_add_device_i2c(foxg20_i2c_devices, ARRAY_SIZE(foxg20_i2c_devices));
> -	/* LEDs */
> -	at91_gpio_leds(foxg20_leds, ARRAY_SIZE(foxg20_leds));
> -	/* Push Buttons */
> -	foxg20_add_device_buttons();
> -#if defined(CONFIG_W1_MASTER_GPIO) || defined(CONFIG_W1_MASTER_GPIO_MODULE)
> -	at91_add_device_w1();
> -#endif
> -}
> -
> -MACHINE_START(ACMENETUSFOXG20, "Acme Systems srl FOX Board G20")
> -	/* Maintainer: Sergio Tanzilli */
> -	.init_time	= at91sam926x_pit_init,
> -	.map_io		= at91_map_io,
> -	.handle_irq	= at91_aic_handle_irq,
> -	.init_early	= foxg20_init_early,
> -	.init_irq	= at91_init_irq_default,
> -	.init_machine	= foxg20_board_init,
> -MACHINE_END
>
diff mbox

Patch

diff --git a/arch/arm/mach-at91/Kconfig.non_dt b/arch/arm/mach-at91/Kconfig.non_dt
index 44ace320d2e1..a2ee352a8904 100644
--- a/arch/arm/mach-at91/Kconfig.non_dt
+++ b/arch/arm/mach-at91/Kconfig.non_dt
@@ -212,12 +212,6 @@  config MACH_CPU9G20
 	  Select this if you are using a Eukrea Electromatique's
 	  CPU9G20 Board <http://www.eukrea.com/>
 
-config MACH_ACMENETUSFOXG20
-	bool "Acme Systems srl FOX Board G20"
-	help
-	  Select this if you are using Acme Systems
-	  FOX Board G20 <http://www.acmesystems.it>
-
 config MACH_PORTUXG20
 	bool "taskit PortuxG20"
 	help
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index 78e9cec282f4..e8efcb00ca94 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -69,7 +69,6 @@  obj-$(CONFIG_MACH_AT91SAM9RLEK)	+= board-sam9rlek.o
 # AT91SAM9G20 board-specific support
 obj-$(CONFIG_MACH_AT91SAM9G20EK) += board-sam9g20ek.o
 obj-$(CONFIG_MACH_CPU9G20)	+= board-cpu9krea.o
-obj-$(CONFIG_MACH_ACMENETUSFOXG20) += board-foxg20.o
 obj-$(CONFIG_MACH_STAMP9G20)	+= board-stamp9g20.o
 obj-$(CONFIG_MACH_PORTUXG20)	+= board-stamp9g20.o
 obj-$(CONFIG_MACH_PCONTROL_G20)	+= board-pcontrol-g20.o board-stamp9g20.o
diff --git a/arch/arm/mach-at91/board-foxg20.c b/arch/arm/mach-at91/board-foxg20.c
deleted file mode 100644
index 8b22c60bb238..000000000000
--- a/arch/arm/mach-at91/board-foxg20.c
+++ /dev/null
@@ -1,272 +0,0 @@ 
-/*
- *  Copyright (C) 2005 SAN People
- *  Copyright (C) 2008 Atmel
- *  Copyright (C) 2010 Lee McLoughlin - lee@lmmrtech.com
- *  Copyright (C) 2010 Sergio Tanzilli - tanzilli@acmesystems.it
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/at73c213.h>
-#include <linux/gpio.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-#include <linux/clk.h>
-#include <linux/w1-gpio.h>
-
-#include <mach/hardware.h>
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/at91sam9_smc.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "sam9_smc.h"
-#include "generic.h"
-#include "gpio.h"
-
-/*
- * The FOX Board G20 hardware comes as the "Netus G20" board with
- * just the cpu, ram, dataflash and two header connectors.
- * This is plugged into the FOX Board which provides the ethernet,
- * usb, rtc, leds, switch, ...
- *
- * For more info visit: http://www.acmesystems.it/foxg20
- */
-
-
-static void __init foxg20_init_early(void)
-{
-	/* Initialize processor: 18.432 MHz crystal */
-	at91_initialize(18432000);
-}
-
-/*
- * USB Host port
- */
-static struct at91_usbh_data __initdata foxg20_usbh_data = {
-	.ports		= 2,
-	.vbus_pin	= {-EINVAL, -EINVAL},
-	.overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-/*
- * USB Device port
- */
-static struct at91_udc_data __initdata foxg20_udc_data = {
-	.vbus_pin	= AT91_PIN_PC6,
-	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
-};
-
-
-/*
- * SPI devices.
- */
-static struct spi_board_info foxg20_spi_devices[] = {
-#if !IS_ENABLED(CONFIG_MMC_ATMELMCI)
-	{
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 1,
-		.max_speed_hz	= 15 * 1000 * 1000,
-		.bus_num	= 0,
-	},
-#endif
-};
-
-
-/*
- * MACB Ethernet device
- */
-static struct macb_platform_data __initdata foxg20_macb_data = {
-	.phy_irq_pin	= AT91_PIN_PA7,
-	.is_rmii	= 1,
-};
-
-/*
- * MCI (SD/MMC)
- * det_pin, wp_pin and vcc_pin are not connected
- */
-static struct mci_platform_data __initdata foxg20_mci0_data = {
-	.slot[1] = {
-		.bus_width	= 4,
-		.detect_pin	= -EINVAL,
-		.wp_pin		= -EINVAL,
-	},
-};
-
-
-/*
- * LEDs
- */
-static struct gpio_led foxg20_leds[] = {
-	{	/* user led, red */
-		.name			= "user_led",
-		.gpio			= AT91_PIN_PC7,
-		.active_low		= 0,
-		.default_trigger	= "heartbeat",
-	},
-};
-
-
-/*
- * GPIO Buttons
- */
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
-static struct gpio_keys_button foxg20_buttons[] = {
-	{
-		.gpio		= AT91_PIN_PC4,
-		.code		= BTN_1,
-		.desc		= "Button 1",
-		.active_low	= 1,
-		.wakeup		= 1,
-	},
-};
-
-static struct gpio_keys_platform_data foxg20_button_data = {
-	.buttons	= foxg20_buttons,
-	.nbuttons	= ARRAY_SIZE(foxg20_buttons),
-};
-
-static struct platform_device foxg20_button_device = {
-	.name		= "gpio-keys",
-	.id		= -1,
-	.num_resources	= 0,
-	.dev		= {
-		.platform_data	= &foxg20_button_data,
-	}
-};
-
-static void __init foxg20_add_device_buttons(void)
-{
-	at91_set_gpio_input(AT91_PIN_PC4, 1);	/* btn1 */
-	at91_set_deglitch(AT91_PIN_PC4, 1);
-
-	platform_device_register(&foxg20_button_device);
-}
-#else
-static void __init foxg20_add_device_buttons(void) {}
-#endif
-
-
-#if defined(CONFIG_W1_MASTER_GPIO) || defined(CONFIG_W1_MASTER_GPIO_MODULE)
-static struct w1_gpio_platform_data w1_gpio_pdata = {
-	/* If you choose to use a pin other than PB16 it needs to be 3.3V */
-	.pin		= AT91_PIN_PB16,
-	.is_open_drain  = 1,
-	.ext_pullup_enable_pin	= -EINVAL,
-};
-
-static struct platform_device w1_device = {
-	.name			= "w1-gpio",
-	.id			= -1,
-	.dev.platform_data	= &w1_gpio_pdata,
-};
-
-static void __init at91_add_device_w1(void)
-{
-	at91_set_GPIO_periph(w1_gpio_pdata.pin, 1);
-	at91_set_multi_drive(w1_gpio_pdata.pin, 1);
-	platform_device_register(&w1_device);
-}
-
-#endif
-
-
-static struct i2c_board_info __initdata foxg20_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("24c512", 0x50),
-	},
-};
-
-
-static void __init foxg20_board_init(void)
-{
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1,
-				ATMEL_UART_CTS
-				| ATMEL_UART_RTS
-				| ATMEL_UART_DTR
-				| ATMEL_UART_DSR
-				| ATMEL_UART_DCD
-				| ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2,
-		ATMEL_UART_CTS
-		| ATMEL_UART_RTS);
-
-	/* USART2 on ttyS3. (Rx & Tx only) */
-	at91_register_uart(AT91SAM9260_ID_US2, 3, 0);
-
-	/* USART3 on ttyS4. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9260_ID_US3, 4,
-		ATMEL_UART_CTS
-		| ATMEL_UART_RTS);
-
-	/* USART4 on ttyS5. (Rx & Tx only) */
-	at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
-
-	/* USART5 on ttyS6. (Rx & Tx only) */
-	at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
-
-	/* Set the internal pull-up resistor on DRXD */
-	at91_set_A_periph(AT91_PIN_PB14, 1);
-	at91_add_device_serial();
-	/* USB Host */
-	at91_add_device_usbh(&foxg20_usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&foxg20_udc_data);
-	/* SPI */
-	at91_add_device_spi(foxg20_spi_devices, ARRAY_SIZE(foxg20_spi_devices));
-	/* Ethernet */
-	at91_add_device_eth(&foxg20_macb_data);
-	/* MMC */
-	at91_add_device_mci(0, &foxg20_mci0_data);
-	/* I2C */
-	at91_add_device_i2c(foxg20_i2c_devices, ARRAY_SIZE(foxg20_i2c_devices));
-	/* LEDs */
-	at91_gpio_leds(foxg20_leds, ARRAY_SIZE(foxg20_leds));
-	/* Push Buttons */
-	foxg20_add_device_buttons();
-#if defined(CONFIG_W1_MASTER_GPIO) || defined(CONFIG_W1_MASTER_GPIO_MODULE)
-	at91_add_device_w1();
-#endif
-}
-
-MACHINE_START(ACMENETUSFOXG20, "Acme Systems srl FOX Board G20")
-	/* Maintainer: Sergio Tanzilli */
-	.init_time	= at91sam926x_pit_init,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= foxg20_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= foxg20_board_init,
-MACHINE_END