| Message ID | 1414486287-25498-3-git-send-email-caesar.wang@rock-chips.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Tue, Oct 28, 2014 at 04:51:24PM +0800, Caesar Wang wrote: > This add the necessary binding documentation for the thermal > found on Rockchip SoCs > > Signed-off-by: zhaoyifeng <zyf@rock-chips.com> > Signed-off-by: Caesar Wang <caesar.wang@rock-chips.com> Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> > --- > .../bindings/thermal/rockchip-thermal.txt | 62 ++++++++++++++++++++++ > 1 file changed, 62 insertions(+) > create mode 100644 Documentation/devicetree/bindings/thermal/rockchip-thermal.txt > > diff --git a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt > new file mode 100644 > index 0000000..fc30e1b > --- /dev/null > +++ b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt > @@ -0,0 +1,62 @@ > +* Temperature Sensor ADC (TSADC) on rockchip SoCs > + > +Required properties: > +- compatible : "rockchip,rk3288-tsadc" > +- reg : physical base address of the controller and length of memory mapped > + region. > +- interrupts : The interrupt number to the cpu. The interrupt specifier format > + depends on the interrupt controller. > +- clocks : Must contain an entry for each entry in clock-names. > +- clock-names : Shall be "tsadc" for the converter-clock, and "apb_pclk" for > + the peripheral clock. > +- #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description. > +- hw-shut-temp : The hardware-controlled shutdown temperature value. > +- tsadc-tshut-mode : The hardware-controlled shutdown mode 0:CRU 1:GPIO. > +- tsadc-tshut-polarity : The hardware-controlled active polarity 0:LOW 1:HIGH. > + > +Exiample: > +tsadc: tsadc@ff280000 { > + compatible = "rockchip,rk3288-tsadc"; > + reg = <0xff280000 0x100>; > + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&cru SCLK_TSADC>, <&cru PCLK_TSADC>; > + clock-names = "tsadc", "apb_pclk"; > + pinctrl-names = "default"; > + pinctrl-0 = <&otp_out>; > + #thermal-sensor-cells = <1>; > + hw-shut-temp = <125000>; > + tsadc-tshut-mode = <0>; > + tsadc-tshut-polarity = <0>; > +}; > + > +Example: referring to thermal sensors: > +thermal-zones { > + cpu_thermal: cpu_thermal { > + polling-delay-passive = <1000>; /* milliseconds */ > + polling-delay = <5000>; /* milliseconds */ > + > + /* sensor ID */ > + thermal-sensors = <&tsadc 1>; > + > + trips { > + cpu_alert0: cpu_alert { > + temperature = <80000>; /* millicelsius */ > + hysteresis = <2000>; /* millicelsius */ > + type = "passive"; > + }; > + cpu_crit: cpu_crit { > + temperature = <120000>; /* millicelsius */ > + hysteresis = <2000>; /* millicelsius */ > + type = "critical"; > + }; > + }; > + > + cooling-maps { > + map0 { > + trip = <&cpu_alert0>; > + cooling-device = > + <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; > + }; > + }; > + }; > +}; > -- > 1.9.1 > >
? 2014?10?29? 07:46, Dmitry Torokhov ??: > On Tue, Oct 28, 2014 at 04:51:24PM +0800, Caesar Wang wrote: >> This add the necessary binding documentation for the thermal >> found on Rockchip SoCs >> >> Signed-off-by: zhaoyifeng <zyf@rock-chips.com> >> Signed-off-by: Caesar Wang <caesar.wang@rock-chips.com> > Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Added. Thank you! > >> --- >> .../bindings/thermal/rockchip-thermal.txt | 62 ++++++++++++++++++++++ >> 1 file changed, 62 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/thermal/rockchip-thermal.txt >> >> diff --git a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt >> new file mode 100644 >> index 0000000..fc30e1b >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt >> @@ -0,0 +1,62 @@ >> +* Temperature Sensor ADC (TSADC) on rockchip SoCs >> + >> +Required properties: >> +- compatible : "rockchip,rk3288-tsadc" >> +- reg : physical base address of the controller and length of memory mapped >> + region. >> +- interrupts : The interrupt number to the cpu. The interrupt specifier format >> + depends on the interrupt controller. >> +- clocks : Must contain an entry for each entry in clock-names. >> +- clock-names : Shall be "tsadc" for the converter-clock, and "apb_pclk" for >> + the peripheral clock. >> +- #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description. >> +- hw-shut-temp : The hardware-controlled shutdown temperature value. >> +- tsadc-tshut-mode : The hardware-controlled shutdown mode 0:CRU 1:GPIO. >> +- tsadc-tshut-polarity : The hardware-controlled active polarity 0:LOW 1:HIGH. >> + >> +Exiample: >> +tsadc: tsadc@ff280000 { >> + compatible = "rockchip,rk3288-tsadc"; >> + reg = <0xff280000 0x100>; >> + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; >> + clocks = <&cru SCLK_TSADC>, <&cru PCLK_TSADC>; >> + clock-names = "tsadc", "apb_pclk"; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&otp_out>; >> + #thermal-sensor-cells = <1>; >> + hw-shut-temp = <125000>; >> + tsadc-tshut-mode = <0>; >> + tsadc-tshut-polarity = <0>; >> +}; >> + >> +Example: referring to thermal sensors: >> +thermal-zones { >> + cpu_thermal: cpu_thermal { >> + polling-delay-passive = <1000>; /* milliseconds */ >> + polling-delay = <5000>; /* milliseconds */ >> + >> + /* sensor ID */ >> + thermal-sensors = <&tsadc 1>; >> + >> + trips { >> + cpu_alert0: cpu_alert { >> + temperature = <80000>; /* millicelsius */ >> + hysteresis = <2000>; /* millicelsius */ >> + type = "passive"; >> + }; >> + cpu_crit: cpu_crit { >> + temperature = <120000>; /* millicelsius */ >> + hysteresis = <2000>; /* millicelsius */ >> + type = "critical"; >> + }; >> + }; >> + >> + cooling-maps { >> + map0 { >> + trip = <&cpu_alert0>; >> + cooling-device = >> + <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; >> + }; >> + }; >> + }; >> +}; >> -- >> 1.9.1 >> >>
diff --git a/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt new file mode 100644 index 0000000..fc30e1b --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/rockchip-thermal.txt @@ -0,0 +1,62 @@ +* Temperature Sensor ADC (TSADC) on rockchip SoCs + +Required properties: +- compatible : "rockchip,rk3288-tsadc" +- reg : physical base address of the controller and length of memory mapped + region. +- interrupts : The interrupt number to the cpu. The interrupt specifier format + depends on the interrupt controller. +- clocks : Must contain an entry for each entry in clock-names. +- clock-names : Shall be "tsadc" for the converter-clock, and "apb_pclk" for + the peripheral clock. +- #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description. +- hw-shut-temp : The hardware-controlled shutdown temperature value. +- tsadc-tshut-mode : The hardware-controlled shutdown mode 0:CRU 1:GPIO. +- tsadc-tshut-polarity : The hardware-controlled active polarity 0:LOW 1:HIGH. + +Exiample: +tsadc: tsadc@ff280000 { + compatible = "rockchip,rk3288-tsadc"; + reg = <0xff280000 0x100>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru SCLK_TSADC>, <&cru PCLK_TSADC>; + clock-names = "tsadc", "apb_pclk"; + pinctrl-names = "default"; + pinctrl-0 = <&otp_out>; + #thermal-sensor-cells = <1>; + hw-shut-temp = <125000>; + tsadc-tshut-mode = <0>; + tsadc-tshut-polarity = <0>; +}; + +Example: referring to thermal sensors: +thermal-zones { + cpu_thermal: cpu_thermal { + polling-delay-passive = <1000>; /* milliseconds */ + polling-delay = <5000>; /* milliseconds */ + + /* sensor ID */ + thermal-sensors = <&tsadc 1>; + + trips { + cpu_alert0: cpu_alert { + temperature = <80000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + cpu_crit: cpu_crit { + temperature = <120000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&cpu_alert0>; + cooling-device = + <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; +};