@@ -42,6 +42,7 @@ struct ohci_at91_priv {
struct clk *uclk;
struct clk *hclk;
bool clocked;
+ bool wakeup; /* Saved wake-up state for resume */
};
/* interface and function clocks; sometimes also an AHB clock */
@@ -61,6 +62,8 @@ extern int usb_disabled(void);
static void at91_start_clock(struct ohci_at91_priv *ohci_at91)
{
+ if (ohci_at91->clocked)
+ return;
if (IS_ENABLED(CONFIG_COMMON_CLK)) {
clk_set_rate(ohci_at91->uclk, 48000000);
clk_prepare_enable(ohci_at91->uclk);
@@ -73,6 +76,8 @@ static void at91_start_clock(struct ohci_at91_priv *ohci_at91)
static void at91_stop_clock(struct ohci_at91_priv *ohci_at91)
{
+ if (!ohci_at91->clocked)
+ return;
clk_disable_unprepare(ohci_at91->fclk);
clk_disable_unprepare(ohci_at91->iclk);
clk_disable_unprepare(ohci_at91->hclk);
@@ -614,15 +619,22 @@ ohci_hcd_at91_drv_suspend(struct device *dev)
struct usb_hcd *hcd = dev_get_drvdata(dev);
struct ohci_hcd *ohci = hcd_to_ohci(hcd);
struct ohci_at91_priv *ohci_at91 = hcd_to_ohci_at91_priv(hcd);
- bool do_wakeup = device_may_wakeup(dev);
int ret;
- if (do_wakeup)
+ /*
+ * Disable wakeup if we are going to sleep with slow clock mode
+ * enabled.
+ */
+ ohci_at91->wakeup = device_may_wakeup(dev)
+ && !at91_suspend_entering_slow_clock();
+
+ if (ohci_at91->wakeup)
enable_irq_wake(hcd->irq);
- ret = ohci_suspend(hcd, do_wakeup);
+ ret = ohci_suspend(hcd, ohci_at91->wakeup);
if (ret) {
- disable_irq_wake(hcd->irq);
+ if (ohci_at91->wakeup)
+ disable_irq_wake(hcd->irq);
return ret;
}
/*
@@ -632,7 +644,7 @@ ohci_hcd_at91_drv_suspend(struct device *dev)
*
* REVISIT: some boards will be able to turn VBUS off...
*/
- if (at91_suspend_entering_slow_clock()) {
+ if (!ohci_at91->wakeup) {
ohci->hc_control = ohci_readl(ohci, &ohci->regs->control);
ohci->hc_control &= OHCI_CTRL_RWC;
ohci_writel(ohci, ohci->hc_control, &ohci->regs->control);
@@ -651,11 +663,10 @@ static int ohci_hcd_at91_drv_resume(struct device *dev)
struct usb_hcd *hcd = dev_get_drvdata(dev);
struct ohci_at91_priv *ohci_at91 = hcd_to_ohci_at91_priv(hcd);
- if (device_may_wakeup(dev))
+ if (ohci_at91->wakeup)
disable_irq_wake(hcd->irq);
- if (!ohci_at91->clocked)
- at91_start_clock(ohci_at91);
+ at91_start_clock(ohci_at91);
ohci_resume(hcd, false);
return 0;
This device needs to be continuously clocked to provide wake up support, previously, if STANDBY target were chosen the device were enable_irq_wake()-prepared and clock still active and if MEM target were chosen the device were also enable_irq_wake()-prepared but not clocked anymore, which is wrong. Now, if STANDBY target is chosen the device is still clocked with wake up support enabled, which were the previous default and if MEM target is chosen the device is declocked with wake up support disabled. Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com> --- drivers/usb/host/ohci-at91.c | 27 +++++++++++++++++++-------- 1 file changed, 19 insertions(+), 8 deletions(-)