@@ -10,33 +10,34 @@ MT6397 is a multifunction device with the following sub modules:
It is interfaced to host controller using SPI interface by a proprietary hardware
called PMIC wrapper or pwrap. MT6397 MFD is a child device of pwrap.
See the following for pwarp node definitions:
-Documentation/devicetree/bindings/soc/mediatek,mt8135-pwrap.txt
+Documentation/devicetree/bindings/soc/pwrap.txt
This document describes the binding for mfd device and its sub module.
Required properties:
compatible: "mediatek,mt6397"
-Optional properties:
-- codec: Audio codec
-- pinctrl: GPIO in mt6397
-- rtc: RTC
-- clock: clocks in mt6397
-- regulators: regulators in mt6397
+Optional subnodes:
+
+- rtc:
+ Required properties:
+ - compatible: "mediatek,mt6397-rtc",
+- regulators
+ Required properties:
+ - compatible: "mediatek,mt6397-regulator",
+ see Documentation/devicetree/bindings/regulator/mt6397-regulator.txt
+- codec
+ Required properties:
+ - compatible: "mediatek,mt6397-codec",
+- clk
+ Required properties:
+ - compatible: "mediatek,mt6397-clk",
Example:
pwrap: pwrap@1000f000 {
compatible = "mediatek,mt8135-pwrap";
- reg = <0 0x1000f000 0 0x1000>,
- <0 0x11017000 0 0x1000>;
- reg-names = "pwrap-base", "pwrap-bridge-base";
- interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
- resets = <&infrarst MT8135_INFRA_PMIC_WRAP_RST>,
- <&perirst MT8135_PERI_PWRAP_BRIDGE_SW_RST>;
- reset-names = "infra-pwrap-rst",
- "peri-pwrap-bridge-rst";
- clocks = <&pmicspi_sel>, <&clk26m>;
- clock-names = "pmicspi-sel", "pmicspi-parent";
+
+ ...
pmic {
compatible = "mediatek,mt6397";
@@ -45,12 +46,6 @@ Example:
compatible = "mediatek,mt6397-codec";
};
- pinctrl@0x0000C000 {
- compatible = "mediatek,mt6397-pinctrl";
- reg = <0 0x0000C000 0 0x0108>;
- gpio-controller;
- };
-
mt6397regulator: mt6397regulator {
compatible = "mediatek,mt6397-regulator";
new file mode 100644
@@ -0,0 +1,217 @@
+Mediatek MT6397 Regulator Driver
+
+Required properties:
+- compatible: "mediatek,mt6397-regulator"
+- mt6397regulator: List of regulators provided by this controller. It is named
+ according to its regulator type, buck_<name> and ldo_<name>.
+ The definition for each of these nodes is defined using the standard binding
+ for regulators at Documentation/devicetree/bindings/regulator/regulator.txt.
+
+The valid names for regulators are::
+BUCK:
+ buck_vpca15, buck_vpca7, buck_vsramca15, buck_vsramca7, buck_vcore, buck_vgpu,
+ buck_vdrm, buck_vio18
+LDO:
+ ldo_vtcxo, ldo_va28, ldo_vcama, ldo_vio28, ldo_vusb, ldo_vmc, ldo_vmch,
+ ldo_vemc3v3, ldo_vgp1, ldo_vgp2, ldo_vgp3, ldo_vgp4, ldo_vgp5, ldo_vgp6,
+ ldo_vibr
+
+Example:
+ pmic {
+ compatible = "mediatek,mt6397";
+
+ mt6397regulator: mt6397regulator {
+ compatible = "mediatek,mt6397-regulator";
+
+ mt6397_vpca15_reg: buck_vpca15 {
+ regulator-compatible = "buck_vpca15";
+ regulator-name = "vpca15";
+ regulator-min-microvolt = < 850000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <12500>;
+ regulator-enable-ramp-delay = <200>;
+ };
+
+ mt6397_vpca7_reg: buck_vpca7 {
+ regulator-compatible = "buck_vpca7";
+ regulator-name = "vpca7";
+ regulator-min-microvolt = < 850000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <12500>;
+ regulator-enable-ramp-delay = <115>;
+ };
+
+ mt6397_vsramca15_reg: buck_vsramca15 {
+ regulator-compatible = "buck_vsramca15";
+ regulator-name = "vsramca15";
+ regulator-min-microvolt = < 850000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <12500>;
+ regulator-enable-ramp-delay = <115>;
+
+ };
+
+ mt6397_vsramca7_reg: buck_vsramca7 {
+ regulator-compatible = "buck_vsramca7";
+ regulator-name = "vsramca7";
+ regulator-min-microvolt = < 850000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <12500>;
+ regulator-enable-ramp-delay = <115>;
+
+ };
+
+ mt6397_vcore_reg: buck_vcore {
+ regulator-compatible = "buck_vcore";
+ regulator-name = "vcore";
+ regulator-min-microvolt = < 850000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <12500>;
+ regulator-enable-ramp-delay = <115>;
+ };
+
+ mt6397_vgpu_reg: buck_vgpu {
+ regulator-compatible = "buck_vgpu";
+ regulator-name = "vgpu";
+ regulator-min-microvolt = < 700000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <12500>;
+ regulator-enable-ramp-delay = <115>;
+ };
+
+ mt6397_vdrm_reg: buck_vdrm {
+ regulator-compatible = "buck_vdrm";
+ regulator-name = "vdrm";
+ regulator-min-microvolt = < 800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-ramp-delay = <12500>;
+ regulator-enable-ramp-delay = <500>;
+ };
+
+ mt6397_vio18_reg: buck_vio18 {
+ regulator-compatible = "buck_vio18";
+ regulator-name = "vio18";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <2120000>;
+ regulator-ramp-delay = <12500>;
+ regulator-enable-ramp-delay = <500>;
+ };
+
+ mt6397_vtcxo_reg: ldo_vtcxo {
+ regulator-compatible = "ldo_vtcxo";
+ regulator-name = "vtcxo";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-enable-ramp-delay = <90>;
+ };
+
+ mt6397_va28_reg: ldo_va28 {
+ regulator-compatible = "ldo_va28";
+ regulator-name = "va28";
+ /* fixed output 2.8 V */
+ regulator-enable-ramp-delay = <218>;
+ };
+
+ mt6397_vcama_reg: ldo_vcama {
+ regulator-compatible = "ldo_vcama";
+ regulator-name = "vcama";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-enable-ramp-delay = <218>;
+ };
+
+ mt6397_vio28_reg: ldo_vio28 {
+ regulator-compatible = "ldo_vio28";
+ regulator-name = "vio28";
+ /* fixed output 2.8 V */
+ regulator-enable-ramp-delay = <240>;
+ };
+
+ mt6397_usb_reg: ldo_vusb {
+ regulator-compatible = "ldo_vusb";
+ regulator-name = "vusb";
+ /* fixed output 3.3 V */
+ regulator-enable-ramp-delay = <218>;
+ };
+
+ mt6397_vmc_reg: ldo_vmc {
+ regulator-compatible = "ldo_vmc";
+ regulator-name = "vmc";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-enable-ramp-delay = <218>;
+ };
+
+ mt6397_vmch_reg: ldo_vmch {
+ regulator-compatible = "ldo_vmch";
+ regulator-name = "vmch";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-enable-ramp-delay = <218>;
+ };
+
+ mt6397_vemc_3v3_reg: ldo_vemc3v3 {
+ regulator-compatible = "ldo_vemc3v3";
+ regulator-name = "vemc_3v3";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-enable-ramp-delay = <218>;
+ };
+
+ mt6397_vgp1_reg: ldo_vgp1 {
+ regulator-compatible = "ldo_vgp1";
+ regulator-name = "vcamd";
+ regulator-min-microvolt = <1220000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-enable-ramp-delay = <240>;
+ };
+
+ mt6397_vgp2_reg: ldo_vgp2 {
+ egulator-compatible = "ldo_vgp2";
+ regulator-name = "vcamio";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-enable-ramp-delay = <218>;
+ };
+
+ mt6397_vgp3_reg: ldo_vgp3 {
+ regulator-compatible = "ldo_vgp3";
+ regulator-name = "vcamaf";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-enable-ramp-delay = <218>;
+ };
+
+ mt6397_vgp4_reg: ldo_vgp4 {
+ regulator-compatible = "ldo_vgp4";
+ regulator-name = "vgp4";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-enable-ramp-delay = <218>;
+ };
+
+ mt6397_vgp5_reg: ldo_vgp5 {
+ regulator-compatible = "ldo_vgp5";
+ regulator-name = "vgp5";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-enable-ramp-delay = <218>;
+ };
+
+ mt6397_vgp6_reg: ldo_vgp6 {
+ regulator-compatible = "ldo_vgp6";
+ regulator-name = "vgp6";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-enable-ramp-delay = <218>;
+ };
+
+ mt6397_vibr_reg: ldo_vibr {
+ regulator-compatible = "ldo_vibr";
+ regulator-name = "vibr";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-enable-ramp-delay = <218>;
+ };
+ };
+ };
@@ -433,6 +433,15 @@ config REGULATOR_MC13892
Say y here to support the regulators found on the Freescale MC13892
PMIC.
+config REGULATOR_MT6397
+ tristate "MediaTek MT6397 PMIC"
+ depends on MFD_MT6397
+ help
+ Say y here to select this option to enable the power regulator of
+ MediaTek MT6397 PMIC.
+ This driver supports the control of different power rails of device
+ through regulator interface.
+
config REGULATOR_PALMAS
tristate "TI Palmas PMIC Regulators"
depends on MFD_PALMAS
@@ -58,6 +58,7 @@ obj-$(CONFIG_REGULATOR_MAX77802) += max77802.o
obj-$(CONFIG_REGULATOR_MC13783) += mc13783-regulator.o
obj-$(CONFIG_REGULATOR_MC13892) += mc13892-regulator.o
obj-$(CONFIG_REGULATOR_MC13XXX_CORE) += mc13xxx-regulator-core.o
+obj-$(CONFIG_REGULATOR_MT6397) += mt6397-regulator.o
obj-$(CONFIG_REGULATOR_QCOM_RPM) += qcom_rpm-regulator.o
obj-$(CONFIG_REGULATOR_PALMAS) += palmas-regulator.o
obj-$(CONFIG_REGULATOR_PFUZE100) += pfuze100-regulator.o
new file mode 100644
@@ -0,0 +1,332 @@
+/*
+ * Copyright (c) 2014 MediaTek Inc.
+ * Author: Flora Fu <flora.fu@mediatek.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/mfd/mt6397/core.h>
+#include <linux/mfd/mt6397/registers.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/mt6397-regulator.h>
+#include <linux/regulator/of_regulator.h>
+
+/*
+ * MT6397 regulators' information
+ *
+ * @desc: standard fields of regulator description.
+ * @qi: Mask for query enable signal status of regulators
+ * @vselon_reg: Register sections for hardware control mode of bucks
+ * @vselctrl_reg: Register for controlling the buck control mode.
+ * @vselctrl_mask: Mask for query buck's voltage control mode.
+ */
+struct mt6397_regulator_info {
+ struct regulator_desc desc;
+ u32 qi;
+ u32 vselon_reg;
+ u32 vselctrl_reg;
+ u32 vselctrl_mask;
+};
+
+#define MT6397_BUCK(match, vreg, min, max, step, volt_ranges, enreg, \
+ vosel, vosel_mask, voselon, vosel_ctrl) \
+[MT6397_ID_##vreg] = { \
+ .desc = { \
+ .name = #vreg, \
+ .of_match = of_match_ptr(match), \
+ .ops = &mt6397_volt_range_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .id = MT6397_ID_##vreg, \
+ .owner = THIS_MODULE, \
+ .n_voltages = (max - min)/step + 1, \
+ .linear_ranges = volt_ranges, \
+ .n_linear_ranges = ARRAY_SIZE(volt_ranges), \
+ .vsel_reg = vosel, \
+ .vsel_mask = vosel_mask, \
+ .enable_reg = enreg, \
+ .enable_mask = BIT(0), \
+ }, \
+ .qi = BIT(13), \
+ .vselon_reg = voselon, \
+ .vselctrl_reg = vosel_ctrl, \
+ .vselctrl_mask = BIT(1), \
+}
+
+#define MT6397_LDO(match, vreg, ldo_volt_table, enreg, enbit, vosel, \
+ vosel_mask) \
+[MT6397_ID_##vreg] = { \
+ .desc = { \
+ .name = #vreg, \
+ .of_match = of_match_ptr(match), \
+ .ops = &mt6397_volt_table_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .id = MT6397_ID_##vreg, \
+ .owner = THIS_MODULE, \
+ .n_voltages = ARRAY_SIZE(ldo_volt_table), \
+ .volt_table = ldo_volt_table, \
+ .vsel_reg = vosel, \
+ .vsel_mask = vosel_mask, \
+ .enable_reg = enreg, \
+ .enable_mask = BIT(enbit), \
+ }, \
+ .qi = BIT(15), \
+}
+
+#define MT6397_REG_FIXED(match, vreg, enreg, enbit, volt) \
+[MT6397_ID_##vreg] = { \
+ .desc = { \
+ .name = #vreg, \
+ .of_match = of_match_ptr(match), \
+ .ops = &mt6397_volt_fixed_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .id = MT6397_ID_##vreg, \
+ .owner = THIS_MODULE, \
+ .n_voltages = 1, \
+ .enable_reg = enreg, \
+ .enable_mask = BIT(enbit), \
+ .min_uV = volt, \
+ }, \
+ .qi = BIT(15), \
+}
+
+static const struct regulator_linear_range buck_volt_range1[] = {
+ REGULATOR_LINEAR_RANGE(700000, 0, 0x7f, 6250),
+};
+
+static const struct regulator_linear_range buck_volt_range2[] = {
+ REGULATOR_LINEAR_RANGE(800000, 0, 0x7f, 6250),
+};
+
+static const struct regulator_linear_range buck_volt_range3[] = {
+ REGULATOR_LINEAR_RANGE(1500000, 0, 0x1f, 20000),
+};
+
+static const u32 ldo_volt_table1[] = {
+ 1500000, 1800000, 2500000, 2800000,
+};
+
+static const u32 ldo_volt_table2[] = {
+ 1800000, 3300000,
+};
+
+static const u32 ldo_volt_table3[] = {
+ 3000000, 3300000,
+};
+
+static const u32 ldo_volt_table4[] = {
+ 1220000, 1300000, 1500000, 1800000, 2500000, 2800000, 3000000, 3300000,
+};
+
+static const u32 ldo_volt_table5[] = {
+ 1200000, 1300000, 1500000, 1800000, 2500000, 2800000, 3000000, 3300000,
+};
+
+static const u32 ldo_volt_table5_v2[] = {
+ 1200000, 1000000, 1500000, 1800000, 2500000, 2800000, 3000000, 3300000,
+};
+
+static const u32 ldo_volt_table6[] = {
+ 1200000, 1300000, 1500000, 1800000, 2500000, 2800000, 3000000, 2000000,
+};
+
+static const u32 ldo_volt_table7[] = {
+ 1300000, 1500000, 1800000, 2000000, 2500000, 2800000, 3000000, 3300000,
+};
+
+static int mt6397_get_status(struct regulator_dev *rdev)
+{
+ int ret;
+ u32 regval;
+ struct mt6397_regulator_info *info = rdev_get_drvdata(rdev);
+
+ ret = regmap_read(rdev->regmap, info->desc.enable_reg, ®val);
+ if (ret != 0) {
+ dev_err(&rdev->dev, "Failed to get enable reg: %d\n", ret);
+ return ret;
+ }
+
+ return (regval & info->qi) ? REGULATOR_STATUS_ON : REGULATOR_STATUS_OFF;
+}
+
+static struct regulator_ops mt6397_volt_range_ops = {
+ .list_voltage = regulator_list_voltage_linear_range,
+ .map_voltage = regulator_map_voltage_linear_range,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .get_status = mt6397_get_status,
+};
+
+static struct regulator_ops mt6397_volt_table_ops = {
+ .list_voltage = regulator_list_voltage_table,
+ .map_voltage = regulator_map_voltage_iterate,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .get_status = mt6397_get_status,
+};
+
+static struct regulator_ops mt6397_volt_fixed_ops = {
+ .list_voltage = regulator_list_voltage_linear,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .get_status = mt6397_get_status,
+};
+
+/* The array is indexed by id(MT6397_ID_XXX) */
+static struct mt6397_regulator_info mt6397_regulators[] = {
+ MT6397_BUCK("buck_vpca15", VPCA15, 700000, 1493750, 6250,
+ buck_volt_range1, MT6397_VCA15_CON7, MT6397_VCA15_CON9, 0x7f,
+ MT6397_VCA15_CON10, MT6397_VCA15_CON5),
+ MT6397_BUCK("buck_vpca7", VPCA7, 700000, 1493750, 6250,
+ buck_volt_range1, MT6397_VPCA7_CON7, MT6397_VPCA7_CON9, 0x7f,
+ MT6397_VPCA7_CON10, MT6397_VPCA7_CON5),
+ MT6397_BUCK("buck_vsramca15", VSRAMCA15, 700000, 1493750, 6250,
+ buck_volt_range1, MT6397_VSRMCA15_CON7, MT6397_VSRMCA15_CON9,
+ 0x7f, MT6397_VSRMCA15_CON10, MT6397_VSRMCA15_CON5),
+ MT6397_BUCK("buck_vsramca7", VSRAMCA7, 700000, 1493750, 6250,
+ buck_volt_range1, MT6397_VSRMCA7_CON7, MT6397_VSRMCA7_CON9,
+ 0x7f, MT6397_VSRMCA7_CON10, MT6397_VSRMCA7_CON5),
+ MT6397_BUCK("buck_vcore", VCORE, 700000, 1493750, 6250,
+ buck_volt_range1, MT6397_VCORE_CON7, MT6397_VCORE_CON9, 0x7f,
+ MT6397_VCORE_CON10, MT6397_VCORE_CON5),
+ MT6397_BUCK("buck_vgpu", VGPU, 700000, 1493750, 6250, buck_volt_range1,
+ MT6397_VGPU_CON7, MT6397_VGPU_CON9, 0x7f,
+ MT6397_VGPU_CON10, MT6397_VGPU_CON5),
+ MT6397_BUCK("buck_vdrm", VDRM, 800000, 1593750, 6250, buck_volt_range2,
+ MT6397_VDRM_CON7, MT6397_VDRM_CON9, 0x7f,
+ MT6397_VDRM_CON10, MT6397_VDRM_CON5),
+ MT6397_BUCK("buck_vio18", VIO18, 1500000, 2120000, 20000,
+ buck_volt_range3, MT6397_VIO18_CON7, MT6397_VIO18_CON9, 0x1f,
+ MT6397_VIO18_CON10, MT6397_VIO18_CON5),
+ MT6397_REG_FIXED("ldo_vtcxo", VTCXO, MT6397_ANALDO_CON0, 10, 2800000),
+ MT6397_REG_FIXED("ldo_va28", VA28, MT6397_ANALDO_CON1, 14, 2800000),
+ MT6397_LDO("ldo_vcama", VCAMA, ldo_volt_table1,
+ MT6397_ANALDO_CON2, 15, MT6397_ANALDO_CON6, 0xC0),
+ MT6397_REG_FIXED("ldo_vio28", VIO28, MT6397_DIGLDO_CON0, 14, 2800000),
+ MT6397_REG_FIXED("ldo_vusb", VUSB, MT6397_DIGLDO_CON1, 14, 3300000),
+ MT6397_LDO("ldo_vmc", VMC, ldo_volt_table2,
+ MT6397_DIGLDO_CON2, 12, MT6397_DIGLDO_CON29, 0x10),
+ MT6397_LDO("ldo_vmch", VMCH, ldo_volt_table3,
+ MT6397_DIGLDO_CON3, 14, MT6397_DIGLDO_CON17, 0x80),
+ MT6397_LDO("ldo_vemc3v3", VEMC3V3, ldo_volt_table3,
+ MT6397_DIGLDO_CON4, 14, MT6397_DIGLDO_CON18, 0x10),
+ MT6397_LDO("ldo_vgp1", VGP1, ldo_volt_table4,
+ MT6397_DIGLDO_CON5, 15, MT6397_DIGLDO_CON19, 0xE0),
+ MT6397_LDO("ldo_vgp2", VGP2, ldo_volt_table5,
+ MT6397_DIGLDO_CON6, 15, MT6397_DIGLDO_CON20, 0xE0),
+ MT6397_LDO("ldo_vgp3", VGP3, ldo_volt_table5,
+ MT6397_DIGLDO_CON7, 15, MT6397_DIGLDO_CON21, 0xE0),
+ MT6397_LDO("ldo_vgp4", VGP4, ldo_volt_table5,
+ MT6397_DIGLDO_CON8, 15, MT6397_DIGLDO_CON22, 0xE0),
+ MT6397_LDO("ldo_vgp5", VGP5, ldo_volt_table6,
+ MT6397_DIGLDO_CON9, 15, MT6397_DIGLDO_CON23, 0xE0),
+ MT6397_LDO("ldo_vgp6", VGP6, ldo_volt_table5,
+ MT6397_DIGLDO_CON10, 15, MT6397_DIGLDO_CON33, 0xE0),
+ MT6397_LDO("ldo_vibr", VIBR, ldo_volt_table7,
+ MT6397_DIGLDO_CON24, 15, MT6397_DIGLDO_CON25, 0xE00),
+};
+
+static int mt6397_set_buck_vosel_reg(struct platform_device *pdev)
+{
+ struct mt6397_chip *mt6397 = dev_get_drvdata(pdev->dev.parent);
+ int i;
+ u32 regval;
+
+ for (i = 0; i < MT6397_MAX_REGULATOR; i++) {
+ if (mt6397_regulators[i].vselctrl_reg) {
+ if (regmap_read(mt6397->regmap,
+ mt6397_regulators[i].vselctrl_reg,
+ ®val) < 0) {
+ dev_err(&pdev->dev,
+ "Failed to read buck ctrl\n");
+ return -EIO;
+ }
+
+ if (regval & mt6397_regulators[i].vselctrl_mask) {
+ mt6397_regulators[i].desc.vsel_reg =
+ mt6397_regulators[i].vselon_reg;
+ }
+ }
+ }
+
+ return 0;
+}
+
+static int mt6397_regulator_probe(struct platform_device *pdev)
+{
+ struct mt6397_chip *mt6397 = dev_get_drvdata(pdev->dev.parent);
+ struct regulator_config config = {};
+ struct regulator_dev *rdev;
+ int i;
+ u32 reg_value, version;
+
+ /* Query buck controller to select activated voltage register part */
+ if (mt6397_set_buck_vosel_reg(pdev))
+ return -EIO;
+
+ /* Read PMIC chip revision to update constraints and voltage table */
+ if (regmap_read(mt6397->regmap, MT6397_CID, ®_value) < 0) {
+ dev_err(&pdev->dev, "Failed to read Chip ID\n");
+ return -EIO;
+ }
+ dev_info(&pdev->dev, "Chip ID = 0x%x\n", reg_value);
+
+ version = (reg_value & 0xFF);
+ switch (version) {
+ case MT6397_REGULATOR_ID91:
+ mt6397_regulators[MT6397_ID_VGP2].desc.volt_table =
+ ldo_volt_table5_v2;
+ break;
+ default:
+ break;
+ }
+
+ for (i = 0; i < MT6397_MAX_REGULATOR; i++) {
+ config.dev = &pdev->dev;
+ config.driver_data = &mt6397_regulators[i];
+ config.regmap = mt6397->regmap;
+ rdev = devm_regulator_register(&pdev->dev,
+ &mt6397_regulators[i].desc, &config);
+ if (IS_ERR(rdev)) {
+ dev_err(&pdev->dev, "failed to register %s\n",
+ mt6397_regulators[i].desc.name);
+ return PTR_ERR(rdev);
+ }
+ }
+
+ return 0;
+}
+
+static struct platform_driver mt6397_regulator_driver = {
+ .driver = {
+ .name = "mt6397-regulator",
+ },
+ .probe = mt6397_regulator_probe,
+};
+
+module_platform_driver(mt6397_regulator_driver);
+
+MODULE_AUTHOR("Flora Fu <flora.fu@mediatek.com>");
+MODULE_DESCRIPTION("Regulator Driver for MediaTek MT6397 PMIC");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:mt6397-regulator");
new file mode 100644
@@ -0,0 +1,49 @@
+/*
+ * Copyright (c) 2014 MediaTek Inc.
+ * Author: Flora Fu <flora.fu@mediatek.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __LINUX_REGULATOR_MT6397_H
+#define __LINUX_REGULATOR_MT6397_H
+
+enum {
+ MT6397_ID_VPCA15 = 0,
+ MT6397_ID_VPCA7,
+ MT6397_ID_VSRAMCA15,
+ MT6397_ID_VSRAMCA7,
+ MT6397_ID_VCORE,
+ MT6397_ID_VGPU,
+ MT6397_ID_VDRM,
+ MT6397_ID_VIO18 = 7,
+ MT6397_ID_VTCXO,
+ MT6397_ID_VA28,
+ MT6397_ID_VCAMA,
+ MT6397_ID_VIO28,
+ MT6397_ID_VUSB,
+ MT6397_ID_VMC,
+ MT6397_ID_VMCH,
+ MT6397_ID_VEMC3V3,
+ MT6397_ID_VGP1,
+ MT6397_ID_VGP2,
+ MT6397_ID_VGP3,
+ MT6397_ID_VGP4,
+ MT6397_ID_VGP5,
+ MT6397_ID_VGP6,
+ MT6397_ID_VIBR,
+ MT6397_ID_RG_MAX,
+};
+
+#define MT6397_MAX_REGULATOR MT6397_ID_RG_MAX
+#define MT6397_REGULATOR_ID97 0x97
+#define MT6397_REGULATOR_ID91 0x91
+
+#endif /* __LINUX_REGULATOR_MT6397_H */