[v2,28/30] ARM: sun7i: olinuxino micro: Convert to DT label based syntax

Commit Message

Maxime Ripard Feb. 11, 2015, 9:01 a.m. UTC

In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax

Signed-off-by: Maxime Ripard <[e-mail]>
---
 arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts | 364 ++++++++++++------------
 1 file changed, 181 insertions(+), 183 deletions(-)

Patch

diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts b/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts
index 714e15ac5416..814cf166f6a1 100644
--- a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts
+++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts
@@ -32,216 +32,214 @@ 
 		spi1 = &spi2;
 	};
 
-	soc@01c00000 {
-		spi1: spi@01c06000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&spi1_pins_a>;
-			status = "okay";
-		};
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins_olinuxino>;
 
-		mmc0: mmc@01c0f000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
-			vmmc-supply = <&reg_vcc3v3>;
-			bus-width = <4>;
-			cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
-			cd-inverted;
-			status = "okay";
+		green {
+			label = "a20-olinuxino-micro:green:usr";
+			gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
 		};
+	};
+};
 
-		mmc3: mmc@01c12000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&mmc3_pins_a>, <&mmc3_cd_pin_olinuxinom>;
-			vmmc-supply = <&reg_vcc3v3>;
-			bus-width = <4>;
-			cd-gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */
-			cd-inverted;
-			status = "okay";
-		};
+&ahci {
+	target-supply = <&reg_ahci_5v>;
+	status = "okay";
+};
 
-		usbphy: phy@01c13400 {
-			usb1_vbus-supply = <&reg_usb1_vbus>;
-			usb2_vbus-supply = <&reg_usb2_vbus>;
-			status = "okay";
-		};
+&ehci0 {
+	status = "okay";
+};
 
-		ehci0: usb@01c14000 {
-			status = "okay";
-		};
+&ehci1 {
+	status = "okay";
+};
 
-		ohci0: usb@01c14400 {
-			status = "okay";
-		};
+&gmac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac_pins_mii_a>;
+	phy = <&phy1>;
+	phy-mode = "mii";
+	status = "okay";
 
-		spi2: spi@01c17000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&spi2_pins_a>;
-			status = "okay";
-		};
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
 
-		ahci: sata@01c18000 {
-			target-supply = <&reg_ahci_5v>;
-			status = "okay";
-		};
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
 
-		ehci1: usb@01c1c000 {
-			status = "okay";
-		};
+	axp209: pmic@34 {
+		compatible = "x-powers,axp209";
+		reg = <0x34>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 
-		ohci1: usb@01c1c400 {
-			status = "okay";
-		};
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+};
 
-		pinctrl@01c20800 {
-			mmc3_cd_pin_olinuxinom: mmc3_cd_pin@0 {
-				allwinner,pins = "PH11";
-				allwinner,function = "gpio_in";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
-			};
-
-			led_pins_olinuxino: led_pins@0 {
-				allwinner,pins = "PH2";
-				allwinner,function = "gpio_out";
-				allwinner,drive = <SUN4I_PINCTRL_20_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-			};
-		};
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_a>;
+	status = "okay";
+};
 
-		lradc: lradc@01c22800 {
-			vref-supply = <&reg_vcc3v0>;
-			status = "okay";
-
-			button@191 {
-				label = "Volume Up";
-				linux,code = <KEY_VOLUMEUP>;
-				channel = <0>;
-				voltage = <191274>;
-			};
-
-			button@392 {
-				label = "Volume Down";
-				linux,code = <KEY_VOLUMEDOWN>;
-				channel = <0>;
-				voltage = <392644>;
-			};
-
-			button@601 {
-				label = "Menu";
-				linux,code = <KEY_MENU>;
-				channel = <0>;
-				voltage = <601151>;
-			};
-
-			button@795 {
-				label = "Search";
-				linux,code = <KEY_SEARCH>;
-				channel = <0>;
-				voltage = <795090>;
-			};
-
-			button@987 {
-				label = "Home";
-				linux,code = <KEY_HOMEPAGE>;
-				channel = <0>;
-				voltage = <987387>;
-			};
-
-			button@1184 {
-				label = "Esc";
-				linux,code = <KEY_ESC>;
-				channel = <0>;
-				voltage = <1184678>;
-			};
-
-			button@1398 {
-				label = "Enter";
-				linux,code = <KEY_ENTER>;
-				channel = <0>;
-				voltage = <1398804>;
-			};
-		};
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	status = "okay";
+};
 
-		uart0: serial@01c28000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&uart0_pins_a>;
-			status = "okay";
-		};
+&lradc {
+	vref-supply = <&reg_vcc3v0>;
+	status = "okay";
 
-		uart6: serial@01c29800 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&uart6_pins_a>;
-			status = "okay";
-		};
+	button@191 {
+		label = "Volume Up";
+		linux,code = <KEY_VOLUMEUP>;
+		channel = <0>;
+		voltage = <191274>;
+	};
 
-		uart7: serial@01c29c00 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&uart7_pins_a>;
-			status = "okay";
-		};
+	button@392 {
+		label = "Volume Down";
+		linux,code = <KEY_VOLUMEDOWN>;
+		channel = <0>;
+		voltage = <392644>;
+	};
 
-		i2c0: i2c@01c2ac00 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&i2c0_pins_a>;
-			status = "okay";
+	button@601 {
+		label = "Menu";
+		linux,code = <KEY_MENU>;
+		channel = <0>;
+		voltage = <601151>;
+	};
 
-			axp209: pmic@34 {
-				compatible = "x-powers,axp209";
-				reg = <0x34>;
-				interrupt-parent = <&nmi_intc>;
-				interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	button@795 {
+		label = "Search";
+		linux,code = <KEY_SEARCH>;
+		channel = <0>;
+		voltage = <795090>;
+	};
 
-				interrupt-controller;
-				#interrupt-cells = <1>;
-			};
-		};
+	button@987 {
+		label = "Home";
+		linux,code = <KEY_HOMEPAGE>;
+		channel = <0>;
+		voltage = <987387>;
+	};
 
-		i2c1: i2c@01c2b000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&i2c1_pins_a>;
-			status = "okay";
-		};
+	button@1184 {
+		label = "Esc";
+		linux,code = <KEY_ESC>;
+		channel = <0>;
+		voltage = <1184678>;
+	};
 
-		i2c2: i2c@01c2b400 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&i2c2_pins_a>;
-			status = "okay";
-		};
+	button@1398 {
+		label = "Enter";
+		linux,code = <KEY_ENTER>;
+		channel = <0>;
+		voltage = <1398804>;
+	};
+};
 
-		gmac: ethernet@01c50000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&gmac_pins_mii_a>;
-			phy = <&phy1>;
-			phy-mode = "mii";
-			status = "okay";
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+	cd-inverted;
+	status = "okay";
+};
 
-			phy1: ethernet-phy@1 {
-				reg = <1>;
-			};
-		};
-	};
+&mmc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc3_pins_a>, <&mmc3_cd_pin_olinuxinom>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */
+	cd-inverted;
+	status = "okay";
+};
 
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins_olinuxino>;
+&ohci0 {
+	status = "okay";
+};
 
-		green {
-			label = "a20-olinuxino-micro:green:usr";
-			gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>;
-			default-state = "on";
-		};
-	};
+&ohci1 {
+	status = "okay";
+};
 
-	reg_ahci_5v: ahci-5v {
-		status = "okay";
+&pio {
+	mmc3_cd_pin_olinuxinom: mmc3_cd_pin@0 {
+		allwinner,pins = "PH11";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
 	};
 
-	reg_usb1_vbus: usb1-vbus {
-		status = "okay";
+	led_pins_olinuxino: led_pins@0 {
+		allwinner,pins = "PH2";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_20_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
 	};
+};
 
-	reg_usb2_vbus: usb2-vbus {
-		status = "okay";
-	};
+&reg_ahci_5v {
+	status = "okay";
+};
+
+&reg_usb1_vbus {
+	status = "okay";
+};
+
+&reg_usb2_vbus {
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_pins_a>;
+	status = "okay";
+};
+
+&spi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&uart6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart6_pins_a>;
+	status = "okay";
+};
+
+&uart7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart7_pins_a>;
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	usb2_vbus-supply = <&reg_usb2_vbus>;
+	status = "okay";
 };