[v2,30/30] ARM: sun8i: ippo q8h v5: Convert to DT label based syntax

Commit Message

Maxime Ripard Feb. 11, 2015, 9:01 a.m. UTC

In order to lessen the amount of duplication of the DT tree, ease the
new and follow the trend that prefers to use label based references
when overriding DTSI nodes, convert the board to this syntax

Signed-off-by: Maxime Ripard <[e-mail]>
---
 arch/arm/boot/dts/sun8i-a23-ippo-q8h-v5.dts | 110 ++++++++++++++--------------
 1 file changed, 54 insertions(+), 56 deletions(-)

Patch

diff --git a/arch/arm/boot/dts/sun8i-a23-ippo-q8h-v5.dts b/arch/arm/boot/dts/sun8i-a23-ippo-q8h-v5.dts
index 623573e46080..4cb25f8267c8 100644
--- a/arch/arm/boot/dts/sun8i-a23-ippo-q8h-v5.dts
+++ b/arch/arm/boot/dts/sun8i-a23-ippo-q8h-v5.dts
@@ -66,69 +66,67 @@ 
 	chosen {
 		bootargs = "earlyprintk console=ttyS0,115200";
 	};
+};
 
-	soc@01c00000 {
-		mmc0: mmc@01c0f000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_q8h>;
-			vmmc-supply = <&reg_vcc3v0>;
-			bus-width = <4>;
-			cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
-			cd-inverted;
-			status = "okay";
-		};
-
-		pinctrl@01c20800 {
-			mmc0_cd_pin_q8h: mmc0_cd_pin@0 {
-				allwinner,pins = "PB4";
-				allwinner,function = "gpio_in";
-				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-				allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
-			};
-		};
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+};
 
-		lradc: lradc@01c22800 {
-			vref-supply = <&reg_vcc3v0>;
-			status = "okay";
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_a>;
+	status = "okay";
+};
 
-			button@200 {
-				label = "Volume Up";
-				linux,code = <KEY_VOLUMEUP>;
-				channel = <0>;
-				voltage = <200000>;
-			};
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	/* pull-ups and devices require PMIC regulator */
+	status = "failed";
+};
 
-			button@400 {
-				label = "Volume Down";
-				linux,code = <KEY_VOLUMEDOWN>;
-				channel = <0>;
-				voltage = <400000>;
-			};
-		};
+&lradc {
+	vref-supply = <&reg_vcc3v0>;
+	status = "okay";
 
-		i2c0: i2c@01c2ac00 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&i2c0_pins_a>;
-			status = "okay";
-		};
+	button@200 {
+		label = "Volume Up";
+		linux,code = <KEY_VOLUMEUP>;
+		channel = <0>;
+		voltage = <200000>;
+	};
 
-		i2c1: i2c@01c2b000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&i2c1_pins_a>;
-			status = "okay";
-		};
+	button@400 {
+		label = "Volume Down";
+		linux,code = <KEY_VOLUMEDOWN>;
+		channel = <0>;
+		voltage = <400000>;
+	};
+};
 
-		i2c2: i2c@01c2b400 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&i2c2_pins_a>;
-			/* pull-ups and devices require PMIC regulator */
-			status = "failed";
-		};
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_q8h>;
+	vmmc-supply = <&reg_vcc3v0>;
+	bus-width = <4>;
+	cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
+	cd-inverted;
+	status = "okay";
+};
 
-		r_uart: serial@01f02800 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&r_uart_pins_a>;
-			status = "okay";
-		};
+&pio {
+	mmc0_cd_pin_q8h: mmc0_cd_pin@0 {
+		allwinner,pins = "PB4";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
 	};
 };
+
+&r_uart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&r_uart_pins_a>;
+	status = "okay";
+};