| Message ID | 1423763647-11687-5-git-send-email-sylvain.rochet@finsecur.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Le 12/02/2015 18:54, Sylvain Rochet a écrit : > This patch add suspend/resume with wakeup support for Atmel USBA. > > On suspend: We stay continuously clocked if Vbus signal is not > available. If Vbus signal is available we set the Vbus signal as a wake > up source then we stop the USBA itself and all clocks used by USBA. > > On resume: We recover clocks and USBA if we stopped them. If a device is > currently connected at resume time we enable the controller. > > Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com> > Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> > --- > drivers/usb/gadget/udc/atmel_usba_udc.c | 57 +++++++++++++++++++++++++++++++++ > 1 file changed, 57 insertions(+) > > diff --git a/drivers/usb/gadget/udc/atmel_usba_udc.c b/drivers/usb/gadget/udc/atmel_usba_udc.c > index 999e2f2..d019b6c 100644 > --- a/drivers/usb/gadget/udc/atmel_usba_udc.c > +++ b/drivers/usb/gadget/udc/atmel_usba_udc.c > @@ -2177,6 +2177,7 @@ static int usba_udc_probe(struct platform_device *pdev) > ret = usb_add_gadget_udc(&pdev->dev, &udc->gadget); > if (ret) > return ret; > + device_init_wakeup(&pdev->dev, 1); > > usba_init_debugfs(udc); > for (i = 1; i < udc->num_ep; i++) > @@ -2192,6 +2193,7 @@ static int __exit usba_udc_remove(struct platform_device *pdev) > > udc = platform_get_drvdata(pdev); > > + device_init_wakeup(&pdev->dev, 0); > usb_del_gadget_udc(&udc->gadget); > > for (i = 1; i < udc->num_ep; i++) > @@ -2201,10 +2203,65 @@ static int __exit usba_udc_remove(struct platform_device *pdev) > return 0; > } > > +#ifdef CONFIG_PM > +static int usba_udc_suspend(struct device *dev) > +{ > + struct usba_udc *udc = dev_get_drvdata(dev); > + > + /* Not started */ > + if (!udc->driver) > + return 0; > + > + mutex_lock(&udc->vbus_mutex); > + > + if (!device_may_wakeup(dev)) { > + usba_stop(udc); > + goto out; > + } > + > + /* > + * Device may wake up. We stay clocked if we failed > + * to request vbus irq, assuming always on. > + */ > + if (gpio_is_valid(udc->vbus_pin)) { > + usba_stop(udc); > + enable_irq_wake(gpio_to_irq(udc->vbus_pin)); > + } > + > +out: > + mutex_unlock(&udc->vbus_mutex); > + return 0; > +} > + > +static int usba_udc_resume(struct device *dev) > +{ > + struct usba_udc *udc = dev_get_drvdata(dev); > + > + /* Not started */ > + if (!udc->driver) > + return 0; > + > + if (device_may_wakeup(dev) && gpio_is_valid(udc->vbus_pin)) > + disable_irq_wake(gpio_to_irq(udc->vbus_pin)); > + > + /* If Vbus is present, enable the controller and wait for reset */ > + mutex_lock(&udc->vbus_mutex); > + udc->vbus_prev = vbus_is_present(udc); > + if (udc->vbus_prev) > + usba_start(udc); > + mutex_unlock(&udc->vbus_mutex); > + > + return 0; > +} > +#endif > + > +static SIMPLE_DEV_PM_OPS(usba_udc_pm_ops, usba_udc_suspend, usba_udc_resume); > + > static struct platform_driver udc_driver = { > .remove = __exit_p(usba_udc_remove), > .driver = { > .name = "atmel_usba_udc", > + .pm = &usba_udc_pm_ops, > .of_match_table = of_match_ptr(atmel_udc_dt_ids), > }, > }; >
diff --git a/drivers/usb/gadget/udc/atmel_usba_udc.c b/drivers/usb/gadget/udc/atmel_usba_udc.c index 999e2f2..d019b6c 100644 --- a/drivers/usb/gadget/udc/atmel_usba_udc.c +++ b/drivers/usb/gadget/udc/atmel_usba_udc.c @@ -2177,6 +2177,7 @@ static int usba_udc_probe(struct platform_device *pdev) ret = usb_add_gadget_udc(&pdev->dev, &udc->gadget); if (ret) return ret; + device_init_wakeup(&pdev->dev, 1); usba_init_debugfs(udc); for (i = 1; i < udc->num_ep; i++) @@ -2192,6 +2193,7 @@ static int __exit usba_udc_remove(struct platform_device *pdev) udc = platform_get_drvdata(pdev); + device_init_wakeup(&pdev->dev, 0); usb_del_gadget_udc(&udc->gadget); for (i = 1; i < udc->num_ep; i++) @@ -2201,10 +2203,65 @@ static int __exit usba_udc_remove(struct platform_device *pdev) return 0; } +#ifdef CONFIG_PM +static int usba_udc_suspend(struct device *dev) +{ + struct usba_udc *udc = dev_get_drvdata(dev); + + /* Not started */ + if (!udc->driver) + return 0; + + mutex_lock(&udc->vbus_mutex); + + if (!device_may_wakeup(dev)) { + usba_stop(udc); + goto out; + } + + /* + * Device may wake up. We stay clocked if we failed + * to request vbus irq, assuming always on. + */ + if (gpio_is_valid(udc->vbus_pin)) { + usba_stop(udc); + enable_irq_wake(gpio_to_irq(udc->vbus_pin)); + } + +out: + mutex_unlock(&udc->vbus_mutex); + return 0; +} + +static int usba_udc_resume(struct device *dev) +{ + struct usba_udc *udc = dev_get_drvdata(dev); + + /* Not started */ + if (!udc->driver) + return 0; + + if (device_may_wakeup(dev) && gpio_is_valid(udc->vbus_pin)) + disable_irq_wake(gpio_to_irq(udc->vbus_pin)); + + /* If Vbus is present, enable the controller and wait for reset */ + mutex_lock(&udc->vbus_mutex); + udc->vbus_prev = vbus_is_present(udc); + if (udc->vbus_prev) + usba_start(udc); + mutex_unlock(&udc->vbus_mutex); + + return 0; +} +#endif + +static SIMPLE_DEV_PM_OPS(usba_udc_pm_ops, usba_udc_suspend, usba_udc_resume); + static struct platform_driver udc_driver = { .remove = __exit_p(usba_udc_remove), .driver = { .name = "atmel_usba_udc", + .pm = &usba_udc_pm_ops, .of_match_table = of_match_ptr(atmel_udc_dt_ids), }, };