| Message ID | 1428657168-12495-3-git-send-email-gabriel.fernandez@linaro.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Fri, Apr 10, 2015 at 11:12:45AM +0200, Gabriel FERNANDEZ wrote: > sti pcie is built around a Synopsis Designware PCIe IP. > > Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> > Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org> Arnd, Rob, can you ack this? > --- > Documentation/devicetree/bindings/pci/st-pcie.txt | 53 +++++++++++++++++++++++ > 1 file changed, 53 insertions(+) > create mode 100644 Documentation/devicetree/bindings/pci/st-pcie.txt > > diff --git a/Documentation/devicetree/bindings/pci/st-pcie.txt b/Documentation/devicetree/bindings/pci/st-pcie.txt > new file mode 100644 > index 0000000..25fcab3 > --- /dev/null > +++ b/Documentation/devicetree/bindings/pci/st-pcie.txt > @@ -0,0 +1,53 @@ > +STMicroelectronics STi PCIe controller > + > +This PCIe host controller is based on the Synopsis Designware PCIe IP > +and thus inherits all the common properties defined in designware-pcie.txt. > + > +Required properties: > + - compatible: "st,stih407-pcie" > + - reg: base address and length of the pcie controller, mem-window address > + and length available to the controller. > + - interrupts: A list of interrupt outputs of the controller. Must contain an > + entry for each entry in the interrupt-names property. > + - interrupt-names: Should be "msi". STi interrupt that is asserted when an > + MSI is received. > + - st,syscfg : should be a phandle of the syscfg node. Also contains syscfg > + offset for IP configuration. > + - resets, reset-names: the power-down and soft-reset lines of PCIe IP. > + Associated names must be "powerdown" and "softreset". > + - phys, phy-names: the phandle for the PHY device. > + Associated name must be "pcie" > + > +Optional properties: > + - reset-gpio: a GPIO spec to define which pin is connected to the bus reset. > + > +Example: > + > +pcie0: pcie@9b00000 { > + compatible = "st,pcie", "snps,dw-pcie"; > + device_type = "pci"; > + reg = <0x09b00000 0x4000>, /* dbi cntrl registers */ > + <0x2fff0000 0x00010000>, /* configuration space */ > + <0x40000000 0x80000000>; /* lmi mem window */ > + reg-names = "dbi", "config", "mem-window"; > + st,syscfg = <&syscfg_core 0xd8 0xe0>; > + #address-cells = <3>; > + #size-cells = <2>; > + ranges = <0x82000000 0 0x20000000 0x20000000 0 0x0FFF0000>; /* non-prefetchable memory */ > + num-lanes = <1>; > + interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "msi"; > + #interrupt-cells = <1>; > + interrupt-map-mask = <0 0 0 7>; > + interrupt-map = <0 0 0 1 &intc GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, /* INT A */ > + <0 0 0 2 &intc GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>, /* INT B */ > + <0 0 0 3 &intc GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>, /* INT C */ > + <0 0 0 4 &intc GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>; /* INT D */ > + > + resets = <&powerdown STIH407_PCIE0_POWERDOWN>, > + <&softreset STIH407_PCIE0_SOFTRESET>; > + reset-names = "powerdown", > + "softreset"; > + phys = <&phy_port0 PHY_TYPE_PCIE>; > + phy-names = "pcie"; > +}; > -- > 1.9.1 >
diff --git a/Documentation/devicetree/bindings/pci/st-pcie.txt b/Documentation/devicetree/bindings/pci/st-pcie.txt new file mode 100644 index 0000000..25fcab3 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/st-pcie.txt @@ -0,0 +1,53 @@ +STMicroelectronics STi PCIe controller + +This PCIe host controller is based on the Synopsis Designware PCIe IP +and thus inherits all the common properties defined in designware-pcie.txt. + +Required properties: + - compatible: "st,stih407-pcie" + - reg: base address and length of the pcie controller, mem-window address + and length available to the controller. + - interrupts: A list of interrupt outputs of the controller. Must contain an + entry for each entry in the interrupt-names property. + - interrupt-names: Should be "msi". STi interrupt that is asserted when an + MSI is received. + - st,syscfg : should be a phandle of the syscfg node. Also contains syscfg + offset for IP configuration. + - resets, reset-names: the power-down and soft-reset lines of PCIe IP. + Associated names must be "powerdown" and "softreset". + - phys, phy-names: the phandle for the PHY device. + Associated name must be "pcie" + +Optional properties: + - reset-gpio: a GPIO spec to define which pin is connected to the bus reset. + +Example: + +pcie0: pcie@9b00000 { + compatible = "st,pcie", "snps,dw-pcie"; + device_type = "pci"; + reg = <0x09b00000 0x4000>, /* dbi cntrl registers */ + <0x2fff0000 0x00010000>, /* configuration space */ + <0x40000000 0x80000000>; /* lmi mem window */ + reg-names = "dbi", "config", "mem-window"; + st,syscfg = <&syscfg_core 0xd8 0xe0>; + #address-cells = <3>; + #size-cells = <2>; + ranges = <0x82000000 0 0x20000000 0x20000000 0 0x0FFF0000>; /* non-prefetchable memory */ + num-lanes = <1>; + interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &intc GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, /* INT A */ + <0 0 0 2 &intc GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>, /* INT B */ + <0 0 0 3 &intc GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>, /* INT C */ + <0 0 0 4 &intc GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>; /* INT D */ + + resets = <&powerdown STIH407_PCIE0_POWERDOWN>, + <&softreset STIH407_PCIE0_SOFTRESET>; + reset-names = "powerdown", + "softreset"; + phys = <&phy_port0 PHY_TYPE_PCIE>; + phy-names = "pcie"; +};