@@ -254,6 +254,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-gw52xx.dtb \
imx6dl-gw53xx.dtb \
imx6dl-gw54xx.dtb \
+ imx6dl-gw551x.dtb \
imx6dl-gw552x.dtb \
imx6dl-hummingboard.dtb \
imx6dl-nitrogen6x.dtb \
@@ -280,6 +281,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-gw53xx.dtb \
imx6q-gw5400-a.dtb \
imx6q-gw54xx.dtb \
+ imx6q-gw551x.dtb \
imx6q-gw552x.dtb \
imx6q-hummingboard.dtb \
imx6q-nitrogen6x.dtb \
new file mode 100644
@@ -0,0 +1,19 @@
+/*
+ * Copyright 2014 Gateworks Corporation
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-gw551x.dtsi"
+
+/ {
+ model = "Gateworks Ventana i.MX6 DualLite/Solo GW551X";
+ compatible = "gw,imx6dl-gw551x", "gw,ventana", "fsl,imx6dl";
+};
new file mode 100644
@@ -0,0 +1,19 @@
+/*
+ * Copyright 2014 Gateworks Corporation
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-gw551x.dtsi"
+
+/ {
+ model = "Gateworks Ventana i.MX6 Dual/Quad GW551X";
+ compatible = "gw,imx6q-gw551x", "gw,ventana", "fsl,imx6q";
+};
new file mode 100644
@@ -0,0 +1,281 @@
+/*
+ * Copyright 2014 Gateworks Corporation
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ /* these are used by bootloader for disabling nodes */
+ aliases {
+ led0 = &led0;
+ nand = &gpmi;
+ ssi0 = &ssi1;
+ usb0 = &usbh1;
+ usb1 = &usbotg;
+ };
+
+ chosen {
+ bootargs = "console=ttymxc1,115200";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_leds>;
+
+ led0: user1 {
+ label = "user1";
+ gpios = <&gpio4 7 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ memory {
+ reg = <0x10000000 0x20000000>;
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_5p0v: regulator@0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "5P0V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_usb_h1_vbus: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "usb_h1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_usb_otg_vbus: regulator@2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ status = "okay";
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ status = "okay";
+};
+
+&hdmi {
+ ddc-i2c-bus = <&i2c3>;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ eeprom1: eeprom@50 {
+ compatible = "atmel,24c02";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+
+ eeprom2: eeprom@51 {
+ compatible = "atmel,24c02";
+ reg = <0x51>;
+ pagesize = <16>;
+ };
+
+ eeprom3: eeprom@52 {
+ compatible = "atmel,24c02";
+ reg = <0x52>;
+ pagesize = <16>;
+ };
+
+ eeprom4: eeprom@53 {
+ compatible = "atmel,24c02";
+ reg = <0x53>;
+ pagesize = <16>;
+ };
+
+ gpio: pca9555@23 {
+ compatible = "nxp,pca9555";
+ reg = <0x23>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ rtc: ds1672@68 {
+ compatible = "dallas,ds1672";
+ reg = <0x68>;
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ gpio_exp: pca9555@24 {
+ compatible = "nxp,pca9555";
+ reg = <0x24>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie>;
+ reset-gpio = <&gpio1 0 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&ssi1 {
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usb_h1_vbus>;
+ status = "okay";
+};
+
+&iomuxc {
+ imx6qdl-gw51xx {
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b0b1
+ MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x1b0b1
+ MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x4001b0b0 /* CAN_STBY */
+ >;
+ };
+
+ pinctrl_gpio_leds: gpioledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpmi_nand: gpminandgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
+ MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_pcie: pciegrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0 /* PCIE RST */
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+ >;
+ };
+ };
+};
Add support for the Gateworks GW5510 board featuring: * i.MX6 SoC * up to 512MB DDR3 * up to 2GB NAND flash * 1x miniPCIe socket (with USB) * HDMI out (micro-HDMI) * HDMI in (micro-HDMI) (currently supported by only vendor kernel) * TTL level I/O (supported by GW16111 breakout board): * I2C * 2x UART * CAN * 2x DIO (GPIO/PWM) * USB OTG For more details see: http://www.gateworks.com/product/item/ventana-gw5510-single-board-computer Signed-off-by: Tim Harvey <tharvey@gateworks.com> --- arch/arm/boot/dts/Makefile | 2 + arch/arm/boot/dts/imx6dl-gw551x.dts | 19 +++ arch/arm/boot/dts/imx6q-gw551x.dts | 19 +++ arch/arm/boot/dts/imx6qdl-gw551x.dtsi | 281 ++++++++++++++++++++++++++++++++++ 4 files changed, 321 insertions(+) create mode 100644 arch/arm/boot/dts/imx6dl-gw551x.dts create mode 100644 arch/arm/boot/dts/imx6q-gw551x.dts create mode 100644 arch/arm/boot/dts/imx6qdl-gw551x.dtsi