Message ID | 1431543609-19646-2-git-send-email-eric@anholt.net (mailing list archive) |
---|---|
State | New, archived |
Headers | show |
On Wed, 13 May 2015, Eric Anholt wrote: > This driver will provide support for calls into the firmware that will > be used by other drivers like cpufreq and vc4. > > Signed-off-by: Eric Anholt <eric@anholt.net> > --- > > v2: Improve commit message, point to mailbox.txt for how mboxes work. > > .../devicetree/bindings/arm/bcm/raspberrypi,firmware.txt | 16 ++++++++++++++++ > 1 file changed, 16 insertions(+) > create mode 100644 Documentation/devicetree/bindings/arm/bcm/raspberrypi,firmware.txt > > diff --git a/Documentation/devicetree/bindings/arm/bcm/raspberrypi,firmware.txt b/Documentation/devicetree/bindings/arm/bcm/raspberrypi,firmware.txt > new file mode 100644 > index 0000000..33b0043 > --- /dev/null > +++ b/Documentation/devicetree/bindings/arm/bcm/raspberrypi,firmware.txt > @@ -0,0 +1,16 @@ > +Raspberry Pi VideoCore firmware driver > + > +Required properties: > + > +- compatible: Should be "rasbperrypi,firmware" > +- mboxes: Single-entry list which specifies which mailbox > + controller and channel is used. See > + Documentation/devicetree/bindings/mailbox/mailbox.txt > + for the semantics of this property That's not what it looks like to me. There is no mention of channels in a 0 cell property. Keep it simple. How about: Phandle to the firmware device's Mailbox. (See: ../mailbox/mailbox.txt for more information) > +Example: > + > +firmware { > + compatible = "rasbperrypi,firmware"; > + mboxes = <&mailbox>; > +};
Lee Jones <lee@kernel.org> writes: > On Wed, 13 May 2015, Eric Anholt wrote: > >> This driver will provide support for calls into the firmware that will >> be used by other drivers like cpufreq and vc4. >> >> Signed-off-by: Eric Anholt <eric@anholt.net> >> --- >> >> v2: Improve commit message, point to mailbox.txt for how mboxes work. >> >> .../devicetree/bindings/arm/bcm/raspberrypi,firmware.txt | 16 ++++++++++++++++ >> 1 file changed, 16 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/arm/bcm/raspberrypi,firmware.txt >> >> diff --git a/Documentation/devicetree/bindings/arm/bcm/raspberrypi,firmware.txt b/Documentation/devicetree/bindings/arm/bcm/raspberrypi,firmware.txt >> new file mode 100644 >> index 0000000..33b0043 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/arm/bcm/raspberrypi,firmware.txt >> @@ -0,0 +1,16 @@ >> +Raspberry Pi VideoCore firmware driver >> + >> +Required properties: >> + >> +- compatible: Should be "rasbperrypi,firmware" >> +- mboxes: Single-entry list which specifies which mailbox >> + controller and channel is used. See >> + Documentation/devicetree/bindings/mailbox/mailbox.txt >> + for the semantics of this property > > That's not what it looks like to me. There is no mention of channels > in a 0 cell property. Keep it simple. How about: > > Phandle to the firmware device's Mailbox. > (See: ../mailbox/mailbox.txt for more information) Sounds good to me.
Den 13.05.2015 21:00, skrev Eric Anholt: > This driver will provide support for calls into the firmware that will > be used by other drivers like cpufreq and vc4. > > Signed-off-by: Eric Anholt <eric@anholt.net> > --- > > v2: Improve commit message, point to mailbox.txt for how mboxes work. > > .../devicetree/bindings/arm/bcm/raspberrypi,firmware.txt | 16 ++++++++++++++++ > 1 file changed, 16 insertions(+) > create mode 100644 Documentation/devicetree/bindings/arm/bcm/raspberrypi,firmware.txt > > diff --git a/Documentation/devicetree/bindings/arm/bcm/raspberrypi,firmware.txt b/Documentation/devicetree/bindings/arm/bcm/raspberrypi,firmware.txt > new file mode 100644 > index 0000000..33b0043 > --- /dev/null > +++ b/Documentation/devicetree/bindings/arm/bcm/raspberrypi,firmware.txt > @@ -0,0 +1,16 @@ > +Raspberry Pi VideoCore firmware driver > + > +Required properties: > + > +- compatible: Should be "rasbperrypi,firmware" > +- mboxes: Single-entry list which specifies which mailbox > + controller and channel is used. See > + Documentation/devicetree/bindings/mailbox/mailbox.txt > + for the semantics of this property > + > +Example: > + > +firmware { > + compatible = "rasbperrypi,firmware"; Typo: rasbperrypi -> raspberrypi > + mboxes = <&mailbox>; > +};
diff --git a/Documentation/devicetree/bindings/arm/bcm/raspberrypi,firmware.txt b/Documentation/devicetree/bindings/arm/bcm/raspberrypi,firmware.txt new file mode 100644 index 0000000..33b0043 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/raspberrypi,firmware.txt @@ -0,0 +1,16 @@ +Raspberry Pi VideoCore firmware driver + +Required properties: + +- compatible: Should be "rasbperrypi,firmware" +- mboxes: Single-entry list which specifies which mailbox + controller and channel is used. See + Documentation/devicetree/bindings/mailbox/mailbox.txt + for the semantics of this property + +Example: + +firmware { + compatible = "rasbperrypi,firmware"; + mboxes = <&mailbox>; +};
This driver will provide support for calls into the firmware that will be used by other drivers like cpufreq and vc4. Signed-off-by: Eric Anholt <eric@anholt.net> --- v2: Improve commit message, point to mailbox.txt for how mboxes work. .../devicetree/bindings/arm/bcm/raspberrypi,firmware.txt | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) create mode 100644 Documentation/devicetree/bindings/arm/bcm/raspberrypi,firmware.txt