diff mbox

[v4,4/5] doc: dt: add documentation for lpc1850-ccu clk driver

Message ID 1432845107-12458-5-git-send-email-manabian@gmail.com (mailing list archive)
State New, archived
Headers show

Commit Message

Joachim Eastwood May 28, 2015, 8:31 p.m. UTC
Add DT binding documentation for lpc1850-ccu clk driver.

Signed-off-by: Joachim Eastwood <manabian@gmail.com>
---
 .../devicetree/bindings/clock/lpc1850-ccu.txt      | 77 ++++++++++++++++++++++
 1 file changed, 77 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/clock/lpc1850-ccu.txt
diff mbox

Patch

diff --git a/Documentation/devicetree/bindings/clock/lpc1850-ccu.txt b/Documentation/devicetree/bindings/clock/lpc1850-ccu.txt
new file mode 100644
index 000000000000..fa97c12014ac
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/lpc1850-ccu.txt
@@ -0,0 +1,77 @@ 
+* NXP LPC1850 Clock Control Unit (CCU)
+
+Each CGU base clock has several clock branches which can be turned on
+or off independently by the Clock Control Units CCU1 or CCU2. The
+branch clocks are distributed between CCU1 and CCU2.
+
+ - Above text taken from NXP LPC1850 User Manual.
+
+This binding uses the common clock binding:
+    Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Required properties:
+- compatible:
+	Should be "nxp,lpc1850-ccu"
+- reg:
+	Shall define the base and range of the address space
+	containing clock control registers
+- #clock-cells:
+	Shall have value <1>.  The permitted clock-specifier values
+	are the branch clock names defined in table below.
+- clocks:
+	Shall contain a list of phandles for the base clocks routed
+	from the CGU to the specific CCU. See mapping of base clocks
+	and CCU in table below.
+- clock-names:
+	Shall contain a list of names for the base clock routed
+	from the CGU to the specific CCU. Valid CCU clock names:
+	"base_usb0_clk",  "base_periph_clk", "base_usb1_clk",
+	"base_cpu_clk",   "base_spifi_clk",  "base_spi_clk",
+	"base_apb1_clk",  "base_apb3_clk",   "base_adchs_clk",
+	"base_sdio_clk",  "base_ssp0_clk",   "base_ssp1_clk",
+	"base_uart0_clk", "base_uart1_clk",  "base_uart2_clk",
+	"base_uart3_clk", "base_audio_clk"
+
+Which branch clocks that are available on the CCU depends on the
+specific LPC part. Check the user manual for your specific part.
+
+A list of CCU clocks can be found in dt-bindings/clock/lpc18xx-ccu.h.
+
+Example board file:
+
+soc {
+	ccu1: clock-controller@40051000 {
+		compatible = "nxp,lpc1850-ccu";
+		reg = <0x40051000 0x1000>;
+		#clock-cells = <1>;
+		clocks = <&cgu BASE_APB3_CLK>,   <&cgu BASE_APB1_CLK>,
+			 <&cgu BASE_SPIFI_CLK>,  <&cgu BASE_CPU_CLK>,
+			 <&cgu BASE_PERIPH_CLK>, <&cgu BASE_USB0_CLK>,
+			 <&cgu BASE_USB1_CLK>,   <&cgu BASE_SPI_CLK>;
+		clock-names = "base_apb3_clk",   "base_apb1_clk",
+			      "base_spifi_clk",  "base_cpu_clk",
+			      "base_periph_clk", "base_usb0_clk",
+			      "base_usb1_clk",   "base_spi_clk";
+	};
+
+	ccu2: clock-controller@40052000 {
+		compatible = "nxp,lpc1850-ccu";
+		reg = <0x40052000 0x1000>;
+		#clock-cells = <1>;
+		clocks = <&cgu BASE_AUDIO_CLK>, <&cgu BASE_UART3_CLK>,
+			 <&cgu BASE_UART2_CLK>, <&cgu BASE_UART1_CLK>,
+			 <&cgu BASE_UART0_CLK>, <&cgu BASE_SSP1_CLK>,
+			 <&cgu BASE_SSP0_CLK>,  <&cgu BASE_SDIO_CLK>;
+		clock-names = "base_audio_clk", "base_uart3_clk",
+			      "base_uart2_clk", "base_uart1_clk",
+			      "base_uart0_clk", "base_ssp1_clk",
+			      "base_ssp0_clk",  "base_sdio_clk";
+	};
+
+	/* A user of CCU brach clocks */
+	uart1: serial@40082000 {
+		...
+		clocks = <&ccu2 CLK_APB0_UART1>, <&ccu1 CLK_CPU_UART1>;
+		...
+	};
+};