| Message ID | 1434549844-11704-1-git-send-email-noralf@tronnes.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On 06/17/2015 08:04 AM, Noralf Trønnes wrote: > Currently poweroff/halt results in a reboot on the Raspberry Pi. > The firmware uses the RSTS register to know which partiton to > boot from. The partiton value is spread into bits > 0, 2, 4, 6, 8, 10. Partiton 63 is a special partition used by > the firmware to indicate halt. > > The firmware made this change in 19 Aug 2013 and was matched > by the downstream commit: > Changes for new NOOBS multi partition booting from gsh Tested-by: Stephen Warren <swarren@wwwdotorg.org> Acked-by: Stephen Warren <swarren@wwwdotorg.org> I wonder if, sometime down the road, it's worth querying the firmware version via the firmware driver and dynamically doing the right thing. Still, the combination of a bleeding edge kernel and an ancient firmware seems a bit unlikely, so perhaps not worth the bother.
On 06/17/2015 07:04 AM, Noralf Trønnes wrote: > Currently poweroff/halt results in a reboot on the Raspberry Pi. > The firmware uses the RSTS register to know which partiton to > boot from. The partiton value is spread into bits > 0, 2, 4, 6, 8, 10. Partiton 63 is a special partition used by > the firmware to indicate halt. > > The firmware made this change in 19 Aug 2013 and was matched > by the downstream commit: > Changes for new NOOBS multi partition booting from gsh > > Signed-off-by: Noralf Trønnes <noralf@tronnes.org> Reviewed-by: Guenter Roeck <linux@roeck-us.net>
diff --git a/drivers/watchdog/bcm2835_wdt.c b/drivers/watchdog/bcm2835_wdt.c index 7116968..43dbf5b 100644 --- a/drivers/watchdog/bcm2835_wdt.c +++ b/drivers/watchdog/bcm2835_wdt.c @@ -36,6 +36,13 @@ #define PM_RSTC_WRCFG_FULL_RESET 0x00000020 #define PM_RSTC_RESET 0x00000102 +/* + * The Raspberry Pi firmware uses the RSTS register to know which partiton + * to boot from. The partiton value is spread into bits 0, 2, 4, 6, 8, 10. + * Partiton 63 is a special partition used by the firmware to indicate halt. + */ +#define PM_RSTS_RASPBERRYPI_HALT 0x555 + #define SECS_TO_WDOG_TICKS(x) ((x) << 16) #define WDOG_TICKS_TO_SECS(x) ((x) >> 16) @@ -151,8 +158,7 @@ static void bcm2835_power_off(void) * hard reset. */ val = readl_relaxed(wdt->base + PM_RSTS); - val &= PM_RSTC_WRCFG_CLR; - val |= PM_PASSWORD | PM_RSTS_HADWRH_SET; + val |= PM_PASSWORD | PM_RSTS_RASPBERRYPI_HALT; writel_relaxed(val, wdt->base + PM_RSTS); /* Continue with normal reset mechanism */
Currently poweroff/halt results in a reboot on the Raspberry Pi. The firmware uses the RSTS register to know which partiton to boot from. The partiton value is spread into bits 0, 2, 4, 6, 8, 10. Partiton 63 is a special partition used by the firmware to indicate halt. The firmware made this change in 19 Aug 2013 and was matched by the downstream commit: Changes for new NOOBS multi partition booting from gsh Signed-off-by: Noralf Trønnes <noralf@tronnes.org> --- v2: Fix typo in commit message v3: Only Raspberry Pi is supported so it's ok to just modify the poweroff function (Stephen Warrren) drivers/watchdog/bcm2835_wdt.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-) -- 2.2.2