@@ -624,6 +624,8 @@ static void analogix_dp_get_max_rx_bandwidth(struct analogix_dp_device *dp,
/*
* For DP rev.1.1, Maximum link rate of Main Link lanes
* 0x06 = 1.62 Gbps, 0x0a = 2.7 Gbps
+ * For DP rev.1.2, Maximum link rate of Main Link lanes
+ * 0x06 = 1.62 Gbps, 0x0a = 2.7 Gbps, 0x14 = 5.4Gbps
*/
analogix_dp_read_byte_from_dpcd(dp, DP_MAX_LINK_RATE, &data);
*bandwidth = data;
@@ -657,7 +659,8 @@ static void analogix_dp_init_training(struct analogix_dp_device *dp,
analogix_dp_get_max_rx_lane_count(dp, &dp->link_train.lane_count);
if ((dp->link_train.link_rate != LINK_RATE_1_62GBPS) &&
- (dp->link_train.link_rate != LINK_RATE_2_70GBPS)) {
+ (dp->link_train.link_rate != LINK_RATE_2_70GBPS) &&
+ (dp->link_train.link_rate != LINK_RATE_5_40GBPS)) {
dev_err(dp->dev, "Rx Max Link Rate is abnormal :%x !\n",
dp->link_train.link_rate);
dp->link_train.link_rate = LINK_RATE_1_62GBPS;
@@ -898,9 +901,6 @@ static void analogix_dp_commit(struct analogix_dp_device *dp)
analogix_dp_enable_rx_to_enhanced_mode(dp, 1);
analogix_dp_enable_enhanced_mode(dp, 1);
- analogix_dp_set_lane_count(dp, dp->video_info->lane_count);
- analogix_dp_set_link_bandwidth(dp, dp->video_info->link_rate);
-
analogix_dp_init_video(dp);
ret = analogix_dp_config_video(dp);
if (ret)
@@ -21,8 +21,9 @@
#define MAX_EQ_LOOP 5
enum link_rate_type {
- LINK_RATE_1_62GBPS = 0x06,
- LINK_RATE_2_70GBPS = 0x0a
+ LINK_RATE_1_62GBPS = DP_LINK_BW_1_62,
+ LINK_RATE_2_70GBPS = DP_LINK_BW_2_7,
+ LINK_RATE_5_40GBPS = DP_LINK_BW_5_4,
};
enum link_lane_count_type {
link_rate and lane_count already configured in analogix_dp_set_link_train(), so we don't need to config those repeatly after training finished, just remove them out. Beside Display Port 1.2 already support 5.4Gbps link rate, the maximum sets would change from {1.62Gbps, 2.7Gbps} to {1.62Gbps, 2.7Gbps, 5.4Gbps}. Signed-off-by: Yakir Yang <ykk@rock-chips.com> --- Changes in v5: None Changes in v4: - Update commit message more readable. (Jingoo) - Adjust the order from 05 to 04 Changes in v3: - The link_rate and lane_count shouldn't config to the DT property value directly, but we can take those as hardware limite. For example, RK3288 only support 4 physical lanes of 2.7/1.62 Gbps/lane, so DT property would like "link-rate = 0x0a" "lane-count = 4". (Thierry) Changes in v2: None drivers/gpu/drm/bridge/analogix/analogix_dp_core.c | 8 ++++---- drivers/gpu/drm/bridge/analogix/analogix_dp_core.h | 5 +++-- 2 files changed, 7 insertions(+), 6 deletions(-)